# TCDS A62CE: Costruzioni Aeronautiche Tecnam S.P.A.

- Type: Type certificate data sheet
- Status: Current
- Holder: Costruzioni Aeronautiche Tecnam S.P.A.
- Revision: 12
- Revised: October 2, 2025
- Product: Aircraft, Small Airplane
- Certification basis: Part 23
- Registered aircraft: 104, by the registry models matched to it (OpenAirDocs)
- Data sheet PDF: https://openairdocs.org/files/sha256/8f/25/8f25278abd7f13663a04f5ffd7b04351ed6d4f0920fe2def5790991b4deb9f41
- FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/DRSDOCID132467602920251113165559.0001
- Page: https://openairdocs.org/tcds/A62CE

## Models (1)

As the data sheet lists them.

- P2006T

## What the data sheet says

From the PDF's text layer, line by line; tables lose their columns. The PDF is the record.

```text
Page No. 1 2 3 4 5 6 
Rev. No. 12 12 8 11 12 12 
 
DEPARTMENT OF TRANSPORTATION 
FEDERAL AVIATION ADMINISTRATION 
 
A62CE 
Revision 12 
Costruzioni Aeronautiche Tecnam S.P.A. 
P2006T 
October 02, 2025 
 
TYPE CERTIFICATE DATA SHEET No. A62CE 
 
This Data Sheet, which is part of Type Certificate No. A62CE, prescribes conditions and limitations under which the 
product for which the Type Certificate was issued meets the airworthiness requirements of the Federal Aviation 
Regulations. 
 
Type Certificate Holder Costruzioni Aeronautiche Tecnam S.P.A. 
Via S. D’acquisto 62 
80042 Boscotrecase (NA) 
Italy 
 
Type Certificate Holder Record Costruzioni Aeronautiche Tecnam srl transferred TC A62CE to Costruzioni 
Aeronautiche Tecnam S.P.A. on March 14, 2018. 
 
I - Model P2006T (Normal Category), Approved November 10, 2010 
 
Engines Two Bombardier-Rotax 912 S3 (TC E00051EN) 
 
Fuel MOGAS ASTM D4814 (Min RON 95) 
AVGAS 100LL (ASTM D910) 
 
Engine Limits Max rotational speed (5 min) 5800 r.p.m. (98.6 hp) 
Max continuous rotational speed 5500 r.p.m. (92.5 hp) 
(Engine shaft r.p.m) 
 
Propeller and Two MT Propeller MTV-21-A-C-F/CF178-05 (TC P16BO) 
Propeller Limits Two blades, constant speed, variable pitch with feathering capability, wood 
construction.  Diameter: 1780 mm (70.08 in) - no reduction allowed. 
Low Pitch Setting     10° 
Feather Position        82° 
 
Oil Oil with API classification "SG" or higher. 
For additional info, refer to "Rotax Operators Manual" - latest issue –  
"Operating Media" Section. 
 
KIAS KCAS  
Airspeed Limits VA (Design Manoeuvring Speed) 119 117  
VFE (Flap Extended Speed)    93   92  LND 
 119 117  TO 
VMC (Minimum Control Speed)   62   62 
VLO (Maximum Landing Gear Operation Speed)   93   92 
VLE (Maximum Landing Gear Extended Speed)   93   92 
VNO (Maximum Structural Cruising Speed)  135 134 
VNE (Never Exceed Speed)  167 168 
 
The following values apply when Tecnam MOD2006/033 is installed (Other Air 
Speeds remain unchanged.)

A62CE           Page 2 of 6  
 
      KIAS KCAS  
VLO (Maximum Landing Gear Operation Speed) 122 119 
VLE (Maximum Landing Gear Extended Speed) 122 119 
 
The following values apply when Tecnam MOD2006/015 is installed (Other Air 
Speeds remain unchanged.) (See NOTE 7) 
      KIAS KCAS  
      VA (Design Manoeuvring Speed) 122 119  
     VFE (Flap Extended Speed)    93   93  LND 
 122 119  TO 
     VNO (Maximum Structural Cruising Speed)  138 135 
     VNE (Never Exceed Speed)  171 172  
 
The following values apply when Tecnam MOD2006/416 is installed (Other Air 
Speeds remain unchanged.) (See NOTE 11) 
      KIAS KCAS  
      VA (Design Manoeuvring Speed) 125 122  
     VFE (Flap Extended Speed)    97   95  LND 
 124 122  TO 
     VNO (Maximum Structural Cruising Speed)  138 135 
     VNE (Never Exceed Speed)  171 170 
 
Center of Gravity (C.G.) Range Forward limit: 8.7 in (16.5 % MAC) behind datum up to 2712 lbs 
   10.7 in (19.5% MAC) behind datum at 2844 lbs (See NOTE 11) 
   Straight line variation between indicated points. 
 Rear limit: 16.34 in (31.0% MAC) behind datum 
 
Empty Weight C.G. Range None 
 
Datum Wing leading edge (MAC = 52.72 in) 
 
Levelling Means Seat support trusses (see Airplane Flight Manual (AFM), 2006/044, Sect.6 for the 
procedure). 
 
Maximum Weight Take-off  2600 lbs 
   2712 lbs (See NOTE 7) 
   2844 lbs (See NOTE 11) 
Zero Fuel 2524 lbs 
  2635 lbs (See NOTE 7) 
  2767 lbs (See NOTE 11) 
Landing   2600 lbs 
  2712 lbs (See NOTE 7) 
  2844 lbs (See NOTE 11) 
 
Minimum Crew 1 pilot 
 
Number of Seats 4 
 
Maximum Compartments Weights 176 lbs at 47.83 in aft the datum 
 
Fuel Capacity 52.8 US Gal (+ 29.7 in) 
Usable 51.35 US Gal 
 
Oil Capacity (each engine)  Maximum:  0.79 US Gal 
Minimum:  0.66 US Gal 
 
Control Surface Movements (*) Ailerons 20° TEU (**) 17° TED (***) 
Stabilator   4° TEU 15° TED

A62CE           Page 3 of 6  
 
Stabilator trim tab   2° TEU 19° TED 
Rudder 26° RH 26° LH 
Rudder trim tab 20° RH 20° LH 
Flaps 15° TED (Take-off position) 
40° TED (Landing position) 
(*) Nominal Values 
(**) Trailing Edge Up 
(***) Trailing Edge Down 
 
Applicable Serial Numbers S/N 1/US to 9999/US 
 
Import Requirements a) A U.S. airworthiness certificate may be issued on the basis of an NAA Export 
Certificate of Airworthiness (Export of C of A) signed by a representative of the 
Ente Nazionale per l'Aviazione Civile (ENAC) on behalf of the European 
Community. The Export C of A should contain the following statement "The 
aircraft covered by this certificate has been examined, tested, and found to 
comply with U.S. Type Certificate No. A62CE and to be in a condition for safe 
operation." 
 
b) The U.S. airworthiness certification basis for aircraft type certificated under 14 
CFR part 21, section 21.29 and exported 
 
c) Each P2006T aircraft must have the following modifications: 
• MOD2006/049 “Engine Starting Battery”, 
• MOD2006/066 “New Powerplant Control Setting Layout” and 
It must be identified with a “Steel identification plate” showing USA S/N 
(xxx/US) and TCDS references.  Aircraft in-service can be modified by Tecnam 
incorporating these modifications using Tecnam Service Bulletin SB 35-CS 
 
d) Refer to the applicable bilateral agreement to verify eligibility for import into the 
United States of both new and used aircraft based on the scope of the agreement, 
to identify any required statements by the exporting authority on the export 
certificate of airworthiness (or equivalent document), and for procedures for 
coordinating exceptions to conformity statements on these documents. Refer to 
FAA Order 8130.2, Airworthiness Certification of Aircraft, for requirements for 
issuance of an airworthiness certificate for imported aircraft. 
 
Certification Basis Type Certification under 14 CFR Section 21.29 including the following 
requirements: 
14 CFR Part 23 effective February 1, 1965 including amdt 23-1 through 23-57 
14 CFR Part 36 effective December 1, 1969 including amdt 36-1 through 36-28 
 
Equivalent levels of safety (ELOS): findings made per the provisions of 14 CFR Part 
21.21(b)(1) for: 
a) ELOS ACE-10-15:  14 CFR § 23. 807(e) Emergency Exits - overhead 
emergency exit size 
b) ELOS ACE-10-16:  14 CFR § 23. 783(b) Doors - proximity of propeller and 
main door 
c) ELOS ACE-10-17:  14 CFR §§ 23.1061 (b), 23.1063 Liquid Cooling and 
Cooling Tank 
d) ELOS ACE-10-18:  14 CFR § 23.777 (d) Cockpit Controls Location - 
Carburetor Heat Location 
 
Approved Kinds of Operation: 
Day and Night, Visual Flight Rules (VFR) and Instrument Flight Rules (IFR)  
 
Prohibited Kinds of Operation: 
Flight into known icing conditions

A62CE           Page 4 of 6  
 
 
Type Certificate No. A62CE was issued November 10, 2010. 
Date of Application for FAA Type Certificate was November 14, 2007. 
 
The European Aviation Safety Agency (EASA) originally type certified this aircraft 
under its type certificate number A.185. 
 
Maximum Operating Altitude 14000 ft 
 
Equipment The basic required equipment as prescribed in the applicable airworthiness  
regulations (see Certification Basis) must be installed in the airplane for certification.  
Such equipment is listed in the current FAA approved AFM: 2006/044 Ed. 2, Rev. 2 
or later approved revisions.  
 
Service Information Each of the documents listed below must state that it is approved by the EASA : 
• Service bulletins,  
• Structural repair manuals,  
• Vendor manuals,  
• Aircraft flight manuals, and  
• Overhaul and maintenance manuals.  
 
The FAA accepts such documents and considers them FAA-approved for type design 
data only unless one of the following conditions exists: 
• The documents change the limitations, performance, or procedures of the 
FAA approved manuals; or 
• The documents make an acoustical or emissions changes to this product’s 
U.S. type certificate as defined in 14 CFR § 21.93.  
 
The FAA uses the post type validation procedures to approve these documents.  The 
FAA may delegate on case-by-case to EASA to approve on behalf of the FAA for the 
U.S. type certificate.  If this is the case, it will be noted on the document.  
 
Each airplane is provided with the following approved documents: 
a) AFM doc. 2006/044 Ed. 2, Rev. 2, or later FAA approved revision. 
b) Airplane Maintenance Manual (AMM) doc. 2006/045 Ed. 2, Rev. 0, or later 
FAA approved revision, including Chapter 4: "Airworthiness Limitations" 
and Chapter 5: "Time Limits/ Maintenance Check".  
c) The appropriate Rotax 912 series engine maintenance manuals. 
d) The appropriate Instruction Manual MT Propellers Doc No. E-124. 
 
NOTES 
 
NOTE 1  Current weight and balance report, including list of equipment included in certificated empty weight 
and loading instructions when necessary, must be provided for each aircraft at the time of original 
certification.  The certificated empty weight and corresponding center of gravity location must include:  
Unusable fuel 8.8 lbs at 29.7 in aft of datum 
Full oil 11.9 lbs at 23.27 in aft of datum 
 
NOTE 2 Airplane operation must be in accordance with the EASA approved AFM listed above.  All placards 
listed in Section 2 must be displayed. 
 
NOTE 3 Airworthiness Limitations are specified in the Section 2 LIMITATIONS of the AFM  and Chapter 4 of 
the AMM and are approved by the EASA and the FAA.  These LIMITATIONS specify mandatory 
replacement times, and operating limitations, and may not be changed without FAA approval . 
 
Revisions to the Airworthiness Limitations must be approved by the FAA.  The inspections, 
maintenance, repair and painting must be accomplished according to the Maintenance Manual or other 
procedures acceptable to the FAA.

A62CE           Page 5 of 6  
 
 
NOTE 4 Information essential for the proper operation, maintenance and inspection of the airplane is contained 
in the Tecnam P2006T AFM and AMM.  
 
NOTE 5 Tecnam Modification No. MOD2006-001 (S-TEC 55x Autopilot). Airplanes can be modified by 
Tecnam at the factory under their major level 1 type design change approval. Airplanes with this 
modification must have Tecnam AFM doc. 2006/044 Ed. 2, Rev.2, Supplement No. A-12 with EASA 
approval date November 12, 2010 or later FAA/EASA approved revisions.   Airplanes with Tecnam 
Modification No. MOD2006-001 (S-TEC 55x Autopilot) when coupled with Garmin G950/1000 
Avionics Suite, must have Tecnam AFM doc. 2006/044 Ed. 2, Rev.2, Supplement No. G -2 with EASA 
approval date November 12, 2010 or later FAA/EASA approved revisions.    
   
NOTE 6 Tecnam Modification No. MOD2006-002 (Glass Cockpit Garmin G950). Airplanes can be modified by 
Tecnam at the factory under their major level 1 type design change approval. Airplanes with this 
modification must have Tecnam AFM doc. 2006/044 Ed. 2, Rev.2, Supplement No. G-1 with EASA 
approval date November 12, 2010 or later FAA/EASA approved revisions and Tecnam P2006T AMM  
Supplement No. SG-1, Ed. 2, Rev. 0, dated. February 28, 2011 or later FAA/EASA approved revisions. 
 
NOTE 7 Tecnam Modification No. MOD2006-015 (Increase Maximum Take-off Weight 1230kg (2712lbs)). 
Airplanes can be modified by Tecnam under their major level 1 type design change approval.  Aircraft 
in-service can incorporate this modification using Tecnam Service Bulletin SB 76-CS (Analogue 
Version) or Tecnam Service Bulletin SB 77-CS (Digital Version). 
 
Analogue Version - Airplanes with this modification must have Tecnam AFM Supplement No. A19 – 
Increased MTOW (1230kg), Ed. 3, Rev. 1 with EASA approval date October 15, 2012 or later 
FAA/EASA approved revisions and Tecnam P2006T AMM Supplement No. S3, Ed. 1, Rev. 0, dated. 
June 25, 2012 or later FAA/EASA approved revisions. 
 
Digital Version - Airplanes with this modification and equipped with Tecnam Modification No. 
MOD2006-002 (Glass Cockpit Garmin G950) must have Tecnam AFM Supplement No. G10 –  
Increased MTOW (1230kg), Ed. 3, Rev. 1 with EASA approval date October 15, 2012 or later 
FAA/EASA approved revisions and Tecnam P2006T AMM Supplement No. S3, Ed. 1, Rev. 0, dated. 
June 25, 2012 or later FAA/EASA approved revisions.  
 
NOTE 8 Tecnam Modification No. MOD2006-033 (VLE and VLO Increment). Airplanes can be modified by 
Tecnam under their major level 1 type design change approval.  Aircraft in-service can incorporate this 
modification using Tecnam Service Bulletin SB 98-CS “VLO and VLE Increment for P2006T aircraft”. 
 
Analogue Version - Airplanes with this modification must have Tecnam AFM Supplement No. A20 –  
VLO/VLE Increase, Ed. 3, Rev. 1, with EASA approval date October 1, 2012 or later FAA/EASA 
approved revisions. 
 
Digital Version - Airplanes with this modification must have Tecnam AFM Supplement No. G11 – 
VLO/VLE Increase, Ed. 3, Rev. 1, with EASA approval date October 1, 2012 or later FAA/EASA 
approved revisions. 
 
NOTE 9 Tecnam Modification No. MOD2006-212 (MD302 Alternative Stand-By Instrument). Airplanes with 
this modification must have Tecnam AFM Supplement No. G16, Rev. 0 with EASA approval date May 
31, 2016 or later FAA/EASA approved revisions and Tecnam P2006T AMM Supplement No. S7, Ed. 
1, Rev 0, dated February 19, 2016 or later FAA/EASA approved revisions. 
 
NOTE 10 Tecnam Modification No. MOD2006-394 (Landing gear fatigue life extension). Airplanes with this 
modification must have Tecnam AMM Chapter 04 Airworthiness Limitations, Ed. 3, Rev. 1, or later 
FAA/EASA approved revision.  Aircraft in service can incorporate this modification using Tecnam 
Service Bulletin SB 467 CS. 
 
NOTE 11 Tecnam Modification No. MOD2006-416 (MTOW up to 1290 kg (2844 lb)). Airplanes with this 
modification must have Tecnam P2006T AFM Supplement No. G29, Rev 0 or later FAA/EASA

A62CE           Page 6 of 6  
 
approved revisions and Tecnam P2006T AMM Doc. No. 2006/045, Ed 3, Rev 3 or later FAA/EASA 
approved revisions.  Aircraft in service can incorporate this modification using Tecnam Service 
Bulletin SB-717-CS. 
 
 
- END -
```

## ADs (9, in force first)

- [AD 2026-19-06](https://openairdocs.org/ad/2026-19-06): Aileron Control System · Costruzioni Aeronautiche Tecnam P2006T. Effective Oct 13, 2026
- [AD 2021-22-22](https://openairdocs.org/ad/2021-22-22): Nose/Tail Landing Gear · Costruzioni Aeronautiche Tecnam P2006T. Effective Dec 3, 2021
- [AD 2018-15-07](https://openairdocs.org/ad/2018-15-07): Flight Controls · Costruzioni Aeronautiche Tecnam P2006T. Effective Sep 4, 2018
- [AD 2015-02-09](https://openairdocs.org/ad/2015-02-09): Engine Exhaust · Costruzioni Aeronautiche Tecnam P2006T. Effective Mar 5, 2015
- [AD 2014-11-09](https://openairdocs.org/ad/2014-11-09): Power Plant · Costruzioni Aeronautiche Tecnam P2006T. Effective Jul 15, 2014
- [AD 2014-02-07](https://openairdocs.org/ad/2014-02-07): Landing Gear · Costruzioni Aeronautiche Tecnam P2006T. Effective Mar 14, 2014
- [AD 2013-04-09](https://openairdocs.org/ad/2013-04-09): Wings · Costruzioni Aeronautiche Tecnam P2006T. Effective Apr 9, 2013
- [AD 2012-18-04](https://openairdocs.org/ad/2012-18-04): Landing Gear · Costruzioni Aeronautiche Tecnam P2006T. Effective Oct 22, 2012
- [AD 2011-13-02](https://openairdocs.org/ad/2011-13-02): Landing Gear · Costruzioni Aeronautiche Tecnam P2006T. Effective Jul 22, 2011

## Registered aircraft by registry model (OpenAirDocs)

- [Costruzioni Aeronautiche Tecna P2006T](https://openairdocs.org/model/costruzioni-aeronautiche-tecna-p2006t): 104 aircraft (registry code 0330001)

## STCs approved under this data sheet (16)

- [STC SA02636SE](https://openairdocs.org/stc/SA02636SE): Installation of Garmin GPS 175 Navigation System and GNX 375 Navigation System with ADS-B In/Out Transponder.. Garmin International Inc.
- [STC SA02019SE-D](https://openairdocs.org/stc/SA02019SE-D): Installation of Garmin Model GTN 625/635/650; 725/750 Navigation System. Garmin International Inc.
- [STC SA02511SE](https://openairdocs.org/stc/SA02511SE): Installation of replacement fuel quantity indicator sending unit(s). CiES Inc.
- [STC SA04046CH PAGE 1](https://openairdocs.org/stc/SA04046CH%20PAGE%201): Installation of L-3 GENESIS  (TM) Electronic Standby Instrument System (ESI-500/MAG-500). Acron Aviation Inc.
- [STC SA02658SE](https://openairdocs.org/stc/SA02658SE): Installation of Garmin GI 275 Multi-Function Display System. Garmin International Inc.
- [STC SA02571SE](https://openairdocs.org/stc/SA02571SE): Installation of Garmin G500/G600 TXi Integrated Avionics System (Primary Flight Display, Multi-Function Display, and Engine Indicating System Display).. Garmin International Inc.
- [STC SA02444AK](https://openairdocs.org/stc/SA02444AK): Approval of the L-3 Communications NGT 9000/9000R ADS-B system installed. ADS-B Technologies LLC
- [STC SA00198MC](https://openairdocs.org/stc/SA00198MC): Installation of mission equipment, to include operator console, RADAR, radome, equipment rack and various antenna. Spec Ops Technology LLC
- [STC SA01714WI](https://openairdocs.org/stc/SA01714WI): Installation of a Garmin transponders: (a) GTX 330/330D/33/33D with ADS-B Out functionality; (b) GTX 335/335R/345/345R with ADS-B Out and In functionality; or (c) GTX 335R/345R with ADS-B Out functionality in select airplanes installed with G950/G1000 systems.. Garmin International Inc
- [STC SA02153LA-D PAGE 1](https://openairdocs.org/stc/SA02153LA-D%20PAGE%201): Installation of Garmin G600 Primary Flight Display (PFD) and Multifunction Display (MFD) System. Garmin International Inc.
- [STC SA02493AK](https://openairdocs.org/stc/SA02493AK): Installation of airborne surveillance Multi Mission Platform (MMP). Borsight, Inc.
- [STC SA04063NY](https://openairdocs.org/stc/SA04063NY): Installation of the mission system Leica City Mapper (Sensor Unit and its respective server, cockpit display and operator stand and display). S4A Solutions For Aviation, S.L.
- [STC SA02119SE PAGE 1](https://openairdocs.org/stc/SA02119SE%20PAGE%201): Installation of Garmin GDL 88 ADS-B UAT Transceiver System. Garmin International Inc
- [STC SA02442AK PAGE 1](https://openairdocs.org/stc/SA02442AK%20PAGE%201): Approval of the L-3 Communications NGT 2000/2500 ADS-B system. ADS-B Technologies, LLC
- [STC SA02121SE](https://openairdocs.org/stc/SA02121SE): Installation of Garmin GTS 825 (TAS) or GTS 855 (TCAS I) Traffic System. Garmin International Inc
- [STC SA02153LA-D](https://openairdocs.org/stc/SA02153LA-D) (historical): Installation of Garmin G600 Primary Flight Display (PFD) and Multifunction Display (MFD) System. Garmin International Inc

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.
