# TCDS E9NE: Pratt & Whitney - Type: Type certificate data sheet - Status: Current - Holder: Pratt & Whitney - Revision: 12 - Revised: December 13, 2010 - Product: Engine - Certification basis: Part 33 - Registered aircraft: 24, by the registry models matched to it (OpenAirDocs) - Data sheet PDF: https://openairdocs.org/files/sha256/79/17/791731dc01d77a749c3980460ced272988422e008d6b6779757df9cbf2800c26 - FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/E902A54C589CFACA862586B800631B4F.0001 - Page: https://openairdocs.org/tcds/E9NE ## Models (5) As the data sheet lists them. - JT8D-217C - JT8D-217A - JT8D-219 - JT8D-209 - JT8D-217 ## What the data sheet says From the PDF's text layer, line by line; tables lose their columns. The PDF is the record. ```text PAGE 1 2 3 4 5 6 7 REV. 12 12 12 8 12 9 12 LEGEND: "- -" INDICATES "SAME AS PRECEDING MODEL" "---" NOT APPLICABLE U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION TYPE CERTIFICATE SHEET NO. E9NE TCDS NUMBER E9NE REVISION: 12 DATE: December 13, 2010 PRATT & WHITNEY MODELS: JT8D-209 JT8D-217 JT8D-217A JT8D-217C JT8D-219 Engines of models described herein conforming with this data sheet (which is part of Type Certificate Number E9NE) and other approved data on file with the Federal Aviation Administration, meet the minimum standards for use in certificated aircraft in accordance with pertinent aircraft data sheets and applicable portions of the Federal Aviation Regulations, provided they are installed, operated, and maintained as prescribed by the approved manufacturer's manuals and other approved instructions. TYPE CERTIFICATE (TC) HOLDER: Pratt & Whitney United Technologies Corporation East Hartford, Connecticut 06108 I. MODELS JT8D-209 JT8D-217 JT8D-217A JT8D-217C JT8D-219 TYPE Dual, axial 14-stage compressor / four-stage turbine / nine can-annular combustion chambers / exhaust mixer RATINGS Sea Level Static Thrust (lbs) Maximum continuous Normal takeoff (5 min.) (See NOTE 19 and NOTE 21) Maximum takeoff (5 min.) (See NOTES 19, 20 and 21) 16,000 18,500 19,250 18,000 20,000 20,850 - - - - - - - - - - - - 18,900 21,000 21,700 FUEL CONTROL Hamilton Standard JFC60-6 - - - - - - - - FUEL PUMP Argo-Tech Corp P/N 384300 - - - - - - - - PRESSURE RATIO BLEED CONTROL PW, P/N 777537 - - PW, P/N 790312 - - - - IGNITION Bendix Type TCFN-2 of Simmonds Type 49988 exciter with two igniters; Champion AA-72S, AC JB-3 FUEL See Note 11 - - - - - - - - TCDS E9NE PAGE 2 I. MODELS (cont.) JT8D-209 JT8D-217 JT8D- 217A JT8D-217C JT8D-219 OIL See Note 12 - - - - - - - - PRINCIPAL DIMENSIONS: Length, in. Width, in. Height, in. 154.20 59.20 67.30 - - - - - - - - - - - - - - - - - - - - - - - - CENTER OF GRAVITY, INCHES (Reflects engines which incorporates the high pressure containment shield identified in Service Bulletin 6053 and the 6th stage bleed system identified in EC 86HA037.) Aft of front mount area centerline Below engine centerline 22.4 2.1 23.0 - - - - - - 23.2 - - - - - - WEIGHT (DRY) Basic engine, (lbs) (includes all essential accessories, with fuel heater, oil tank, and fuel-oil cooler, but excludes starter, exhaust nozzle, and power source for the ignition system. (*See Note 22, **23, ***24) Airframe Brackets, (lbs). (See Note 25) Transition Duct, (lbs) 4,588 20 85 4,623 - - - - - - - - - - 4,684* 4,646** 4,750*** 10 - - - - - - - - - - - - NOTES 1-20 TCDS E9NE PAGE 3 CERTIFICATION BASIS JT8D-209 JT8D-217, -217A JT8D-217C, -219 14 CFR Part 33 effective February 1, 1965, as amended by 33-1, 33-2, 33-3, 33-4, 33-5, 33-6. Exemption Numbers 2479 and 2743 14 CFR Part 33 effective February 1, 1965, as amended by 33-1, 33-2, 33-3, 33-4, 33-5, 33-6. Exemption Number 2897 14 CFR Part 33 effective February 1, 1965, as amended by 33-1, 33-2, 33-3, 33-4, 33-5, 33-6. Exemption Number 2897-1. Equivalent Level of Safety (ELOS) No. 8040-ELOS-10-NE04 to 14 CFR §33.87 (b)(2)(ii) is also applicable for JT8D-217C and -219 Models that incorporate the High Horsepower Extraction Option (Note 24). DATE OF TYPE CERTIFICATE MODEL DATE OF APPLICATION NO. E9NE ISSUED/REVISED JT8D-209 April 20, 1977 June 22, 1979 JT8D-209A December 2, 1977 Canceled October 31, 1981 JT8D-217 October 27, 1978 October 31, 1980 JT8D-217A February 16, 1981 October 30, 1981 JT8D-219 January 25, 1983 February 22, 1985 JT8D-217C November 25, 1985 February 26, 1986 PRODUCTION BASIS Producti on Certificate No. 2 TCDS E9NE PAGE 4 NOTES JT8D-209 JT8D-217 JT8D- 217A JT8D-217C JT8D-219 NOTE 1. Rotor Speeds - Maximum permissible engine oper ating speeds for the engine rotors are as follows: Low Pressure rotor (N1), rpm Normal takeoff (ARTS armed) All other operating conditions High pressure rotor (N2), rpm Normal takeoff (ARTS armed) All other operating conditions 7,850 8,150 12,150 12,370 7,770 - - 12,285 12,550 8,080 8,350 12,350 - - 8,080 - - - - - - 8,120 - - - - - - NOTE 2. Temperatures - Maximum permissible temperatures are as follows: Turbine outlet gas temperature, ºC/ºF: Maximum takeoff (5 min) Normal takeoff (5 min) Maximum continuous Maximum for acceleration-- Maximum takeoff (2 min) Normal takeoff (2 min) 570/1058 550/1022 530/986 625/1157 590/1094 580/1076 630/1166 595/1103 - - - - - - - - - - - - - - - - - - - - - - - - - - - - Turbine outlet gas temperature at start-up, ºC/ºF: Ground In-Flight 500/932 570/1058 - - 625/1157 - - - - - - - - - - - - Oil inlet temperature, ºC/ºF: Continuous operation Transient operation 135/275 165/329 - - - - - - - - - - - - - - - - Transient operation above 135ºC (275ºF), is limited to 15 minutes. External engine component maximum limiting temperatures are specified in the Installation Handbook, Part A. NOTE 3. Pressures - Fuel and oil pressure limits are as follows: Fuel Pressure - At inlet to engine system pump, not less that 5 psig above true vapor pressure of the fuel and not greater that 50 psig with a vapor liquid ratio of zero. Oil Pressure - Minimum 35 psig Normal Range 40-55 psig Note: During cold weather starting, oil pressure in excess of 55 psig may be evidenced until oil viscosities are reduced by increasing oil temperature. Engine operation is limited to idle power when oil pressure is in excess of 55 psig during cold weather starts. TCDS E9NE PAGE 5 NOTE 4. Air Bleed Extraction - Maximum permissible air bleed extraction is as follows: Percentage of Primary Engine Airflow Simultaneous Individual Bleeding Bleeding of Two at a Single Station or More Stations Station N o r m a l Maximum Normal Maximum High-Pressure Bleed: At and below 90 percent maximum continuous thrust Above 90 percent maximum continuous thrust Eight-Stage Bleed: At and below maximum continuous thrust Above maximum continuous thrust Low Pressure Bleed: At 20% maximum continuous thrust and above Below 20% maximum continuous thrust 8.0 3.5 4.0 2.75 3.5 2.8 8.0 *5.5 4.0 *3.25 3.5 2.8 8.0 3.5 4.0 2.75 3.5 2.8 8.0 *5.5 4.0 *3.25 3.5 2.8 NOTE: The above limits apply when the bleed is taken fr om all available bleed ports of any one bleed station. The allowable eighth-stage bleed is in addition to the bleed used to anti-ice the engine inlet guide vanes and the airframe supplied nose cone. Percentage of Secondary Airflow Fan Air bleed: At and below maximum continuous thrust Above maximum continuous thrust 3.0 2.0 *4.0 2.0 3.0 2.0 3.0 2.0 *Usable only when required by a malfunction and only until the next landing. NOTE 5. The ratings are based on static test stand operation under the follow ing conditions: Compressor inlet air at 59°F and 29.92 in. Hg. Nozzle exhaust pipe per P&WA 46701. P&WA bellmouth on air inlet. No aircraft accessory l oads or air extraction. No anti-icing air flow. Turbine outlet gas temperature limits and engine rotor speed limits not exceeded. TCDS E9NE PAGE 6 NOTE 6. The following accessory drive provisions are incorporated: Torque Speed Ratio to (lb-in.) Overhang Drive Rotation Turbine Shaft Cont. Static (in.-lb.) Low-Pressure Rotor N1: Tachometer C 0.511:1 7 50 --- High-Pressure Rotor N2: Starter C 0.597:1 * * 625 Generator C 0.700:1 1500 6600** 2500 Fluid Power Pump C 0.292:1 1000 4400 400 Tachometer CC 0.343:1 7 50 --- C - Clockwise: CC - Counterclockwise * - Maximum starter torque - 550 lb-ft. The shear section will fail at 850 - 0 + 100 lb-ft. ** - Maximum torque when used as a starter, 410 lb-ft. NOTE 7. Power setting, power checks, and control of engine output in all operations is to be based upon Pratt & Whitney Aircraft engine charts referring to turbine discharge section gas pressures. Pressure probes are included in the engine assembly for this reason. NOTE 8. These engines meet FAA requirements for adequat e turbine disk integrity and rotor blade containment and do not require external armoring. These engines have demonstrated satisfactory operation in icing conditions as defined in Federal Aviation Regulation 33.68. NOTE 9. DELETED. NOTE 10. The maximum continuous static thrust at sea level at 19°F temperature and below is 19,250 pounds (JT8D-209), 20,850 pounds (JT8D-217, -217A, -217C) and 21,700 pounds (JT8D-219) respectively. The Engine Installation Handbook, Part A, should be consulted for variation in thrust between standard and 19°F. NOTE 11. The following fuels are approved for these engines: Fuels and fuel additives conforming to the latest applicable issue for FAA approved Pratt & Whitney Service Bulletin No. 2016 may be used separately or mixed in any proportions without adversely affecting the engine operation or power output. No fuel control adjustment is required when switching fuel types. NOTE 12. The following oils are approved for these engines : brand name oils listed in Pratt & Whitney Service Bulletin No. 238. (Synthetic type conforming to Pratt & Whitney Aircraft Specification 521, as revised). NOTE 13. All these engines meet t he January 1, 1984, fuel venting emission requirements of SFAR-27. NOTE 14. All these engines meet t he January 1, 1984, smoke and gaseous emission requirements of SFAR-27. NOTE 15. Certain engine parts are life lim ited. These limits are listed in the FAA approved Pratt & Whitney Aircraft JT8D-200 Series Turbofan Engine Manual, Part No. 773128, Time Limit Section. See NOTE 20 when using the JT8D-219 auxiliary maximum takeoff rating. NOTE 16. Maximum permissible inlet dist ortion limit for these engines is specified in the Installation Handbook, Part A. NOTE 17. Information regarding transient rotor shaft over-speed rpm and number of overspeed occurrences, as well as transient gas over-temperature and number of over-temperature occurrences, is specified in the Maintenance Manual, Part No. 773127. TCDS E9NE PAGE 7 NOTE 18. The JT8D-217 is the same as JT8D-209 except for incorporation of a cooled high pressure turbine and improved engine parts. JT8D-217A is the same as JT8D-217 except for 20,000 pounds of static takeoff thrust at sea level flat rated to 84°F ambient temperature and improved engine parts. The JT8D-219 is the same as the JT8D-217A except that it incorporates improved parts including longer fan blades and an improved cooled high pressure turbine to permit increases in the thrust ratings. The JT8D-217C is the same as the JT8D-219 except that it has -217A ratings and operating limits. NOTE 19. A thrust setting limited to 19,250 lbs. (JT8D-209), 20,850 lbs. (JT8D-217, -217A, -217C) and 21,700 lbs. (JT8D-219) static thrust at sea level, flat rated to 84°F ambient temperature has been established as maximum takeoff thrust rating. A thrust setting limited to 18,500 lbs. (JT8D-209), 20,000 lbs. (JT8D-217) static thrust at seal level, flat rated to 77°F ambient temperature and 20,000 lbs. (JT8D-217A-217C) and 21,000 lbs. (JT8D-219) static thrust at sea level, flat rated to 84°F ambient temperature has been established as normal takeoff thrust rating for normal takeoff operation. When the automatic reset mechanism in the fuel control is armed, operation to the Normal Takeoff Rating Operating limits will prevent the engine from exceeding the Maximum Takeoff Rating Operating Limits when the reset mechanism is actuated. The time limit at the Normal takeoff Rating is five minutes and shall include any time accumulated above the Normal Takeoff Rating. NOTE 20. A thrust setting is limited to 21,700 lbs. static thrust at sea level, flat rated to 90.4°F ambient temperature has been established as auxiliary maximum takeoff for the JT8D-219 engine model. The auxiliary maximum takeoff setting provides additional hot day performance on the JT8D-219 engine model only and is achieved by manual setting of the power lever only, with the automatic reset mechanism disarmed (off). The part life accounting procedure is the same as for the maximum takeoff rating except that a two for one cycle penalty must be applied to the sixth stage compressor disk whenever the auxiliary maximum takeoff rating is applied. NOTE 21. Note 22. Note 23. Note 24. Note 25. The 5 minute takeoff time may be extended to 10 minutes for one engine inoperative or shutdown for engines which have incorporated all the features specified in Pratt & Whitney Aircraft Turbojet Engine Service Bulletin Numbers 5514, 5643 and Alert Service Bulletin Number A6196. For MD80 installations. Reflects Boeing approval of increased engine weight up to 4704 lbs including airframe brackets. Also includes SB5871, 6th stage bleed system (32 lbs); SB6053, HPT containment (65 lbs); SB6346, improved HPT containment (22 lbs); and SB6478, Improved forward fan case, approved for MD80 aircraft by STC00228BO (34 lbs). For Super 27 installations. Includes SB6053, HPT containment (65 lbs); SB6346, Improved HPT containment (22 lbs); and SB6491, improved forward fan case (34 lbs). For Boeing 707 installations. Includes SB5871, 6th stage bleed system (32 lbs); SB6053, HPT containment (65 lbs); SB6346, improved HPT containment (22 lbs); and SB6491, Improved forward fan case (34 lbs) as well as the following features: Externals Modification Option for B707 Top Mount (17 lbs); Nickel HPC Disks and Spacer Option (10 lbs); and High Horsepower Extraction Option (60 lbs). For Boeing 707 installations add 10 lbs for airframe brackets (instead of 20 lbs for all other installations). ----END---- ``` ## ADs (38, in force first) - [AD 2021-22-19](https://openairdocs.org/ad/2021-22-19): Turbine Engine Compressor Section · Pratt & Whitney JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Dec 28, 2021 - [AD 2015-14-05](https://openairdocs.org/ad/2015-14-05): Cracking in the low-pressure turbine (LPT) shaft · Pratt & Whitney Division JT8D-217C and JT8D-219. Effective Aug 25, 2015 - [AD 2011-04-04](https://openairdocs.org/ad/2011-04-04): Critical life-limited parts · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Mar 22, 2011 - [AD 97-17-04 R1](https://openairdocs.org/ad/97-17-04-R1): Front compressor front hub · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217C and 1 more. Effective Apr 22, 2010 - [AD 2006-17-07 R1](https://openairdocs.org/ad/2006-17-07-R1): High pressure compressor (HPC) front hubs and HPC disk · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Nov 2, 2006 - [AD 2005-21-01](https://openairdocs.org/ad/2005-21-01): High pressure turbine (HPT) shaft · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Nov 21, 2005 - [AD 2005-17-16](https://openairdocs.org/ad/2005-17-16): Critical life-limited rotating parts · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 17 more. Effective Sep 30, 2005 - [AD 2004-26-04](https://openairdocs.org/ad/2004-26-04): HPT containment hardware · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Feb 9, 2005 - [AD 2003-16-05](https://openairdocs.org/ad/2003-16-05): High pressure compressor (HPC) disks · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Sep 12, 2003 - [AD 2002-21-17](https://openairdocs.org/ad/2002-21-17): Fan duct and fan exit guide vane · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Nov 29, 2002 - [AD 2002-16-08](https://openairdocs.org/ad/2002-16-08): Combustion Chamber Outer Case (CCOC) · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Sep 20, 2002 - [AD 99-10-11](https://openairdocs.org/ad/99-10-11): Fan Blades and Shrouds · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Jun 14, 1999 - [AD 99-01-08](https://openairdocs.org/ad/99-01-08): Stage 7 through Stage 15 High-Pressure Compressor (HPC) Disks · Pratt & Whitney Division JT3D-1, JT3D-1-MC6, JT3D-1-MC7 and 30 more. Effective Jan 5, 1999 - [AD 98-21-24](https://openairdocs.org/ad/98-21-24): Compressor Disks · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 17 more. Effective Nov 16, 1998 - [AD 96-15-06](https://openairdocs.org/ad/96-15-06): First Stage Fan Hubs · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Sep 3, 1996 - [AD 95-02-16](https://openairdocs.org/ad/95-02-16): Fuel Nozzle and Support Assembly · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 17 more. Effective Feb 21, 1995 - [AD 91-24-14](https://openairdocs.org/ad/91-24-14): Bearing Seal Spacer · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Jan 21, 1992 - [AD 88-04-02](https://openairdocs.org/ad/88-04-02): Anti-rotation Pin Failures · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Mar 4, 1988 - [AD 87-03-13](https://openairdocs.org/ad/87-03-13): Compressor Blade · Pratt & Whitney Division JT8D-209, JT8D-217 and JT8D-217A. Effective Feb 16, 1987 - [AD 80-15-51](https://openairdocs.org/ad/80-15-51): Engine Rear Compressor Front Hubs · Pratt & Whitney Division JT8D-209, JT8D-1, JT8D-11 and 11 more. Effective Aug 21, 1980 - [AD 75-05-06](https://openairdocs.org/ad/75-05-06): Fuel Manifold Leakage · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Feb 24, 1977 - [AD 70-26-05](https://openairdocs.org/ad/70-26-05): First Stage Compressor Rotor Blades · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Dec 29, 1970 - [AD 70-25-08](https://openairdocs.org/ad/70-25-08): Seventh Stage Compressor Rotor Disc · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Dec 15, 1970 - [AD 70-11-03](https://openairdocs.org/ad/70-11-03): Sixth Stage Compressor Discs · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Jun 12, 1970 - [AD 70-02-02](https://openairdocs.org/ad/70-02-02): Sixth Stage Compressor Rotor Disc · Pratt & Whitney Division JT8D-1, JT8D-11, JT8D-15 and 18 more. Effective Apr 15, 1970 - [AD 2011-07-02](https://openairdocs.org/ad/2011-07-02) (historical): Turbine Blade · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Apr 28, 2011 - [AD 2006-17-07](https://openairdocs.org/ad/2006-17-07) (historical): Fretting and fluorescent magnetic particle inspections (FMPI) for cracking in the area of the tierod holes on the HPC front hubs · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 18 more. Effective Oct 4, 2006 - [AD 2005-18-02](https://openairdocs.org/ad/2005-18-02) (historical): Engine manufacturer's time limits section (TLS) · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Feb 28, 2006 - [AD 2005-02-03](https://openairdocs.org/ad/2005-02-03) (historical): Turbine (LPT) Blades 3rd and 4th Stage · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Mar 3, 2005 - [AD 2002-23-14](https://openairdocs.org/ad/2002-23-14) (historical): High Pressure Compressor (HPC) Front Hubs · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Dec 31, 2002 - [AD 2002-13-09](https://openairdocs.org/ad/2002-13-09) (historical): Rotating engine parts · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Dec 30, 2002 - [AD 2000-21-07](https://openairdocs.org/ad/2000-21-07) (historical): Critical Life-Limited Parts · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Apr 23, 2001 - [AD 99-26-06](https://openairdocs.org/ad/99-26-06) (historical): Combustion Chamber Outer Case · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Feb 22, 2000 - [AD 99-27-01](https://openairdocs.org/ad/99-27-01) (historical): Low Pressure Turbine Blades · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Feb 2, 2000 - [AD 99-22-14](https://openairdocs.org/ad/99-22-14) (historical): High Pressure Turbine Shaft · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Dec 28, 1999 - [AD 99-12-04](https://openairdocs.org/ad/99-12-04) (historical): Critical Life Limited Part Inspection · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Jul 8, 1999 - [AD 97-19-13](https://openairdocs.org/ad/97-19-13) (historical): High Pressure Turbine (HPT) Shaft · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217A and 2 more. Effective Oct 24, 1997 - [AD 97-17-04](https://openairdocs.org/ad/97-17-04) (historical): Fan Hubs · Pratt & Whitney Division JT8D-209, JT8D-217, JT8D-217C and 1 more. Effective Sep 30, 1997 ## Registered aircraft by registry model (OpenAirDocs) - [Pratt & Whitney JT8D-219](https://openairdocs.org/engine/pratt-whitney-jt8d-219): 22 aircraft (registry code 51694) - [Pratt & Whitney JT8D-217C](https://openairdocs.org/engine/pratt-whitney-jt8d-217c): 2 aircraft (registry code 51693) - [Pratt & Whitney JT8D-209](https://openairdocs.org/engine/pratt-whitney-jt8d-209): 0 aircraft (registry code 51690) - [Pratt & Whitney JT8D-217](https://openairdocs.org/engine/pratt-whitney-jt8d-217): 0 aircraft (registry code 51691) - [Pratt & Whitney JT8D-217A](https://openairdocs.org/engine/pratt-whitney-jt8d-217a): 0 aircraft (registry code 51692) ## STCs approved under this data sheet (12) - [STC SE482CH](https://openairdocs.org/stc/SE482CH): Installation of Tube Processing Corporation (TPC) JT8D-200 Anti-Ice tube assemblies Part Numbers 2026-TP, 2027-TP, 2028-TP and 2029-TP and support brackets Part Number 2060-TP, 2061-TP, 2062-TP and 2063-TP. United Technologies Corporation, Pratt & Whitney Division - [STC SE01944LA](https://openairdocs.org/stc/SE01944LA): Installation of a JET Engineering, Ltd. Turbine Exhaust Cone Mixer (TECM).. Jet Engineering LTD - [STC SE02128AT](https://openairdocs.org/stc/SE02128AT): Installation of a replacement ring manufactured by Praxair as part of the Praxair Second Stage Turbine inner air seal ring assembly.. PAS Technologies Inc - [STC SE00429AT](https://openairdocs.org/stc/SE00429AT): Incorporate an alternate gear box stud installation.. Jet Avion Corporation - [STC SE2117SO](https://openairdocs.org/stc/SE2117SO): Installation of an oil tank safety cap adapter which prevents loss of oil in the event of loss or damage to the oil filler cap.. Jet Avion Corporation - [STC SE01650SE](https://openairdocs.org/stc/SE01650SE): Installation of Aviation Fleet Solutions MD-80 heavy weight noise abatement system. Aviation FLeet Solutions LLC - [STC SE6025NM](https://openairdocs.org/stc/SE6025NM): Installation of P/N T98781 first stage turbine nozzle guide vanes.. Kellstrom Defense Aerospace Inc. - [STC SE2930SO](https://openairdocs.org/stc/SE2930SO): Installation of an alternate gearbox cover seal utilizing an aluminum retainer .040-inch thick with a molded-in-place elastomeric seal contoured to fit the main housing/cover flange interface.. Parker O-Seal Division - [STC SE1683GL](https://openairdocs.org/stc/SE1683GL): Installation of Rexnord O-Ring face seal P/N's 1-1337-701, 1-1633-701, 1-1738-701, and/or1-2233-701.. Rexnord, Inc - [STC SE86WE](https://openairdocs.org/stc/SE86WE): Replace the airoils on P&WA P/Ns 495051, 478351, 583751, 653851, 653951, 572451, 583351, 653751, 653151, 676951, 728951, 709951, 710751, 627751, 737271, 578551, 738271, 747171, 792871, 786471, 583751, 777971, 780591, 782571, 793181, 799771, 794481, 794491 , 798781, and 799191.. Chromizing Company - [STC SE557NE](https://openairdocs.org/stc/SE557NE): Installation of oil tank shuttle valve.. Stockbridge William D - [STC SE1930SO](https://openairdocs.org/stc/SE1930SO): Installation of power control shaft bushing.. Cook Airtomic Division --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.