# TCDS HR1SO: Orlando Helicopter Airways Inc. - Type: Type certificate data sheet - Status: Current - Holder: Orlando Helicopter Airways Inc. - Revision: 11 - Revised: August 13, 2003 - Product: Aircraft, Rotorcraft - Certification basis: Part 21, Part 27 - Registered aircraft: 10, by the registry models matched to it (OpenAirDocs) - Data sheet PDF: https://openairdocs.org/files/sha256/03/41/0341dc87c4a28019506e4b0c2a9778d2d4a72769be652f2d9a34cbfd2041f098 - FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/ABC1FE0A127203B786256F3C005EB334.0001 - Page: https://openairdocs.org/tcds/HR1SO ## Models (10) As the data sheet lists them. - UH-19C - CH-19E - H-19A - HRS-3/H-19B - UH-19D - H-19G - UH-19F - H-19D - YH-19A - HRS-1/CH-19 ## What the data sheet says From the PDF's text layer, line by line; tables lose their columns. The PDF is the record. ```text DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION HR1SO Revision 11 Orlando Helicopter Airways, Inc. HRS-1/CH-19 H-19D H-19A H-19G YH-19A UH-19F UH-19C CH-19E HRS-3/H-19B UH-19D August 13, 2003 TYPE CERTIFICATE DATA SHEET NO. HR1SO This data sheet, which is part of Type Certificate No. HR1SO, prescribes conditions and limitations under which the product for which the type certificate was issued, meets the airworthiness requirements of the Federal Aviation Regulations. Type Certificate Holder: Orlando Helicopter Airways, Inc. 1380 Flightline Blvd. Deland Airport Deland, FL 32723 I. - Model HRS-1/CH-19 (Restricted Category Military Surplus) approved April 8, 1966 II. - Model H-19A, YH-19A, UH-19C (Restricted Category Military Surplus) approved November 3, 1970 Engine: Pratt and Whitney R-1340-57 (See Note 8 regarding helicopter, engines and appliances) Fuel: 91/96 minimum grade aviation gasoline (See note 11 for alternate fuels) Engine Limits: Maximum Continuous (Sea level) 35.0 in. Hg., 2250 rpm (550 hp) (Straight line manifold pressure variation with altitude to 8000 ft.) 33.0 in. Hg. 2200 rpm (550 hp) Take-off (one minute) 36.5 in. Hg., 2250 rpm (600 hp) Rotor Speed Limits: Maximum 245 rpm Normal Operating Range 185 rpm to 220 rpm, Minimum 170 rpm Airspeed limits: Vne (never exceed) 95 knots (See NOTE 2 for required placard) Other Limits: T.O. AN 01-230HJA-1 and Orlando Helicopter Airways FAA approved Flight Manual Supplement dated April 8, 1966. The helicopters approved under this type certificate are done so under the concept of limited exposure associated with escape from inadvertent ice encounters, and are prohibited against flight into known icing. The helicopters must be re-evaluated if certification to the General Ice protection Airworthiness Regulations is requested. Page No. 1 2 3 4 5 6 Rev. 11 11 11 11 11 11 HR1SO Page 2 of 6 Center of Gravity (C.G.) Range: (125.0) to (136.0) Empty Weight Refer to Operators Manual USAF Model HRS-1/CH-19, H-19A, YH-19A, UH-19C (C.G.) Range: Helicopters. Datum: 130.6 in. forward of center of main rotor hub. Leveling Means: Plumb line from top of cabin doorframe to index plate on cabin floor. (See Note 1.) Maximum Weight: 7200 lbs. Minimum Crew: 1 (Pilot) Number of Seats: See Note 11 Fuel Capacity: 100 gallons forward tank, 72 gallons rear tank. Oil Capacity: 9.4 gallons Rotor Blade and For rigging information, refer to Maintenance Manual USAF Model HRS-1/CH-19, Control Movement: H-19A, YH-19A, UH-19C Helicopters. Serial No’s. Approved: Model HRS-1/CH-19, H-19A, YH-19A, UH-19C helicopters that have been approved are identified in FAA approved Orlando Helicopter Airways, Inc., Eligible Serial Number Report # 01-3551, dated October 21, 2001 or later FAA approved revision. Current copy is available at the Atlanta Aircraft Certification Office, Atlanta, Georgia. III. - Model HRS-3/H-19B, H-19D, H-19G, (Restricted Category Military Surplus) approved January 23, 1967 IV. - Model UH-19F, CH-19E (Restricted Category Military Surplus) approved November 3, 1970 V. - Model UH-19D (Restricted Category Military Surplus) approved October 17, 1978 Engine: Wright R 1300-3 series (See Note 8 regarding helicopter, engines and appliances) Fuel: 91/96 minimum grade aviation gasoline (See note 11 for alternate fuels) Engine Limits: Maximum Continuous (all operations) (Sea level) 39.5 in. Hg., 2400 rpm (700 hp) (Straight line manifold pressure variation with altitude to 5000 ft.) 38.0 in. Hg. 2400 rpm (700 hp) Rotor Speed Limits: Maximum 245 rpm Normal Operating Range 185 rpm to 220 rpm, Minimum 170 rpm Airspeed Limits: Vne (never exceed) 95 knots (See Note 2 for required placard) Other Limits: T.O. AN 01-230HJA-1 for HRS-3 or T.O. 1H-19(H)B-1for H-19B/ -19D/-19G and Orlando Helicopter Airways FAA approved Flight Manual Supplement dated April 8, 1966. The helicopters approved under this type certificate are done so under the concept of limited exposure associated with escape from inadvertent ice encounters, and are prohibited against flight into known icing. The helicopters must be re-evaluated if certification to the General Ice protection Airworthiness Regulations is requested. HR1SO Page 3 of 6 Center of Gravity (C.G.) Range: (125.0) to (136.0) Empty Weight Refer to Operators Manual USAF Model HRS-1/CH-19, H-19A, YH-19A, UH-19C (C.G.) Range: Helicopters. Datum: 130.6 in. forward of center of main rotor hub. Leveling Means: Plumb line from top of cabin doorframe to index plate on cabin floor. (See Note 1.) Maximum Weight: 7900 lbs. Minimum Crew: 1 (Pilot) No of Seats: See Note 11 Fuel Capacity: 100 gallons forward tank, 72 gallons rear tank. Oil Capacity: 9.4 gallons Rotor Blade and For rigging information, refer to Maintenance Manual USAF Model HRS-1/CH-19, Control Movement: H-19A, YH-19A, UH-19C Helicopters. Serial No’s. Approved: Model HRS-3/H-19B, H-19D, H-19G, UH-19F, CH-19E, UH-19D helicopters that have been approved are identified in FAA approved Orlando Helicopter Airways, Inc., Eligible Serial Number Report # 01-3551, dated October 21, 2001 or later FAA approved revision. Current copy is available at the Atlanta Aircraft Certification Office, Atlanta, Georgia. Data Pertinent to All Models: Certification Basis: FAR 21.25(a)(2), effective February 1, 1965, including Amendments 21-1 through 21-71 for the special purpose of: (1) Agriculture Operations under FAR 21.25(b)(1) Note: In accordance with FAR 36.1(a)(4), compliance with the noise requirements was not shown. Therefore, aircraft certificated under this type certificate are only eligible for agricultural operations excepted by FAR 36.1(a)(4) and defined under FAR 137.3 (2) Forest and Wildlife Conservation Operations under FAR 21.25(b)(2). Note: In accordance with FAR 36.1(a)(4), compliance with the noise requirements was not shown. Therefore, aircraft certificated under this type certificate are only eligible for dispensing fire fighting materials excepted by FAR 36.1(a)(4) and defined under FAR 137.3 (3) External Load Operations. Note: In accordance with FAR 36.1(a)(4), compliance with the noise requirements was not shown. Therefore, aircraft certificated under this type certificate are only eligible for external load operations excepted by FAR 36.1(a)(4) and defined under FAR 133.1(a). HR1SO Page 4 of 6 Any alteration to the helicopter for Special Purposes not identified above require further FAA approval and in addition, may require additional noise and/or flight testing. General Note: Any subsequent modifications to the helicopters type certified under this Type Certificate are to have the certification basis for that modification established under 14CFR 21.101 published June 7, 2000 which became effective June 10, 2003. Otherwise non-significant modifications are to meet the requirements of CAR 6, Amendment 6-1 thru 6-5 dated December 20, 1956, normal category, and 14 CFR 27.1529, Instructions for continued airworthiness, Amendment 18, effective September 11, 1980. Date of Application: April 5, 1966, Amended: April 8, 1966, January 23, 1967, November 3, 1970, October 17, 1978. Production Basis: None. No helicopters may be produced under this approval. (See Note 4) Prior to adding serial numbers to this Type Certificate, each candidate helicopter must undergo a conformity inspection. The conformity inspection will be conducted in accordance with a Type Inspection Authorization, Part 1, or request for conformity that will include as a minimum, the inspections contained in the FAA Rotorcraft Directorate Restricted Category Conformity document dated September 25, 2001 or later FAA approved revisions. Equipment: The basic required equipment as prescribed in the applicable airworthiness regulations (see Certification Basis) must be installed in or on each helicopter for certification. In addition, equipment necessary for the particular special purpose must be installed. NOTES Note 1: A current weight and balance report including a list of equipment included in the certified empty weight, and loading instructions, when necessary, must be in each type helicopter at time of original airworthiness certification and at all times thereafter. Note 2: The following placards must be prominently displayed in the cabin in clear view of the pilot: Placard No. 1 THIS ROTOR CRAFT MUST BE OPERATED IN ACCORDANCE WITH THE RESTRICTED CATEGORY OPERATING LIMITATIONS OF FAR 91.313. Placard No. 2 AIRSPEED LIMITS: NEVER EXCEED SPEED, Vne 95 KIAS WHEN SPRAY BOOM INSTALLED, 50 KIAS EXTERNAL LOAD IN CARGO SLING, 40 KIAS. Placard No. 3 AGRICULTURAL OPERATIONS MUST BE CONDUCTED IN ACCORDANCE WITH FAR PART 137. Placard No. 4 INSTRUMENT FLIGHT PROHIBITED Placard No. 5 See Note 14 below. Placard No. 6 See Note 15 below. Note 3: This model helicopter must be serviced, maintained, inspected, repaired and overhauled in accordance with the following technical manuals: AN 01-230HJA, AN 02A-10DD-2, T.O. 2R-R1300-12, AN 01-230HGA-4, AN 01-230HG-3 and T.O. 1H-19(H)A-3. HR1SO Page 5 of 6 Note 4: In addition to the standard helicopter requirements, the following additional data and/or helicopter configuration requirements must be met for each individual HRS-1/CH-19, H- 19D, H-19A, H-19G, YH-19A, UH-19F, UH-19C, CH-19E, HRS-3/H-19B and UH-19D helicopter upon application for an original Special Airworthiness Certificate: (a) A completed Application for Airworthiness Certificate, FAA Form 8130-6 that has correctly identified the type certificate holder’s helicopter and its intended special purpose(s). (b) Written confirmation from the certifying office that the affected serial number has been added to Orlando Helicopter Airways type certificate. (c) The application for airworthiness cer tification and the helicopter’s registration certification must match the information on Orlando Helicopter Airways data plate. (d) The Helicopter Flight Manual and documents specified in Note 3 are with the helicopter. (e) The conditions and limitations specified in Orlando Helicopter Airways Type Certificate Data Sheet HR1SO dated August 6, 2003 or later FAA approved revisions are met. (f) Modifications in accordance with Orlando Helicopter Airways Report OHA-1A, OHA-1B or other FAA approved special purpose modification. (g) The provisions of AD 54-1-3, AD 54-13-1, AD 54-16-1, AD 54-19-2, AD 54-20-2, AD 55-25-4, AD 56-16-3, AD 56-23-3, AD 60-13-4 and AD 63-5-2 (AD 63-5-2 extended service life to 1200 hours when operating over sparsely populated areas), AD 65-8-2, AD 66-4-3 (AD 66-4-3 extended service life to 3500 hours when operating over sparsely populated areas), and AD 67-17-6. (h) The provisions of USAF T.O. 1H-19-532, 1H-19-543 and 1H-19-556. Note 5: This helicopter is prohibited from carrying cargo for compensation or hire. Carriage of cargo is limited to such cargo that is incidental to the helicopter owners/operator’s business, which is other than air transportation. Note 6: A restricted category helicopter may not be operated in a foreign country without the express written approval of that country. Note 7: This helicopter has not been shown to meet the requirements of the applicable comprehensive and detailed Airworthiness Code as provided by Annex 8, to the Convention of the International Civil Aviation Organization. Note 8: Military to Civil or Military to Military engine changes are allowed, provided the replacement engine is of the same make and model as identified in this TCDS. The military or civil replacement engine must have proper military or civil records and have the applicable FAA Airworthiness Inspection accomplished and is in an airworthy condition. Note 9: The Airworthiness Directives (AD) for the helicopter and engine contained in Orlando Helicopter Airways, Airworthiness Directive Report must be complied with prior to original certification. Provisions of applicable AD’s shall apply to each model. (See Note 4 above for list of applicable AD’s and Military Technical Orders.) Note 10: Alternate and emergency fuels are listed in the applicable Operators Manual for each applicable Model Helicopter. Some limitations apply for the use of certain alternative fuels. These limitations are listed in this section. Note 11: No person may be carried in this helicopter during flight unless that person is essential to the purpose of the flight. HR1SO Page 6 of 6 Note 12: Any Alteration to the type design of this aircraft may require Instructions for Continued Airworthiness. If so, these instructions must be submitted and accepted by the FAA Fort Worth Evaluation Group (FTW-AEG), prior to approval for return to service. Note 13: Component overhaul intervals and replacement time shall be in accordance with Sikorsky Aircraft Engineering recommended and customer approved component overhaul intervals and replacement times. Part I (8 pages), Part II (4 pages), Part III (5 pages) and Part IV (5pages), dated 1 December 1956, unless superseded by appropriate Airworthiness Directive. Note 14: Reference Note 4, item (g) AD 63-5-2. Placard required on instrument panel in front of pilot: “WHEN OPERATING WITH S14-10-2000 ROTOR BLADES INSTALLED IN EXCESS OF 1000 HRS. OPERATIONS AUTHORIZED OVER SPARSELY POPULATED AREAS ONLY. NO OPERATIONS AUTHORIZED BEYOND 1200 HRS. BLADE TIME.” Note 15: Reference Note 4, item (g) AD 66-4-3. Placard required on instrument panel in front of pilot: “WHEN OPERATING WITH S14-10-2100 ROTOR BLADES INSTALLED IN EXCESS OF 2250 HRS. OPERATIONS AUTHORIZED OVER SPARSELY POPULATED AREAS ONLY. NO OPERATIONS AUTHORIZED BEYOND 3500 HRS. BLADE TIME.” …..END….. ``` ## ADs (17, in force first) - [AD 66-04-03](https://openairdocs.org/ad/66-04-03): Main Rotor Blades · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 3 more. Effective Apr 27, 1976 - [AD 75-04-02](https://openairdocs.org/ad/75-04-02): Main Rotor Spindles · Orlando Helicopter Airways CH-19E, H-19A, H-19D and 8 more. Effective Feb 19, 1975 - [AD 74-19-04](https://openairdocs.org/ad/74-19-04): Applicability to All HRS/H19 Series · Orlando Helicopter Airways HRS-1/CH-19 and HRS-3/H-19B. Effective Sep 10, 1974 - [AD 70-09-05](https://openairdocs.org/ad/70-09-05): Main Rotor Shaft · Orlando Helicopter Airways H-19D, H-19G, HRS-1/CH-19 and 1 more. Effective Apr 30, 1970 - [AD 67-29-07](https://openairdocs.org/ad/67-29-07): Azimuth Control Rod Assembly · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more. Effective Nov 3, 1967 - [AD 67-17-06](https://openairdocs.org/ad/67-17-06): Pylon Lower Ring · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more. Effective May 21, 1967 - [AD 65-08-02](https://openairdocs.org/ad/65-08-02): Main Rotor Blades · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 11 more. Effective Apr 9, 1965 - [AD 63-05-02](https://openairdocs.org/ad/63-05-02): Main Rotor Blades · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more. Effective Mar 6, 1963 - [AD 54-01-03](https://openairdocs.org/ad/54-01-03): Fuel Strainer Screen · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 54-13-01](https://openairdocs.org/ad/54-13-01): Star Assembly Bolt Replacement · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 54-16-01](https://openairdocs.org/ad/54-16-01): Main Transmission · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 54-19-02](https://openairdocs.org/ad/54-19-02): Servo Safety Clip · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 54-20-02](https://openairdocs.org/ad/54-20-02): Support Assembly Cracks · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 55-25-04](https://openairdocs.org/ad/55-25-04): Tail Cone Skin Reinforcements · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 56-16-03](https://openairdocs.org/ad/56-16-03): Main Rotor Blade Inspection · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-51 and 3 more - [AD 56-23-03](https://openairdocs.org/ad/56-23-03): Horizontal Hinge Pin Assembly · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-55 and 2 more - [AD 60-13-04](https://openairdocs.org/ad/60-13-04): Rotor Shank Rod · Orlando Helicopter Airways HRS-1/CH-19, HRS-3/H-19B, S-51 and 3 more ## Registered aircraft by registry model (OpenAirDocs) - [Sikorsky UH-19D](https://openairdocs.org/model/sikorsky-uh-19d): 6 aircraft (registry code 814161G) - [Sikorsky H-19D](https://openairdocs.org/model/sikorsky-h-19d): 3 aircraft (registry code 8141610) - [Sikorsky CH-19E](https://openairdocs.org/model/sikorsky-ch-19e): 1 aircraft (registry code 8141616) - [Orlando Helicopter H-19D](https://openairdocs.org/model/orlando-helicopter-h-19d): 0 aircraft (registry code 8151610) - [Sikorsky H-19A](https://openairdocs.org/model/sikorsky-h-19a): 0 aircraft (registry code 8141608) - [Sikorsky H-19G](https://openairdocs.org/model/sikorsky-h-19g): 0 aircraft (registry code 8141618) - [Sikorsky HRS-3/H-19B](https://openairdocs.org/model/sikorsky-hrs-3-h-19b): 0 aircraft (registry code 8141611) - [Sikorsky UH-19C](https://openairdocs.org/model/sikorsky-uh-19c): 0 aircraft (registry code 8141609) - [Sikorsky UH-19F](https://openairdocs.org/model/sikorsky-uh-19f): 0 aircraft (registry code 814161J) ## STCs approved under this data sheet (15) - [STC SH3319NM](https://openairdocs.org/stc/SH3319NM): Installation of Precise Flight Pulselite Control Unit in the Landing /Taxi Recognition Visual Control Light system,. Precise Flight Inc - [STC SR02704SE](https://openairdocs.org/stc/SR02704SE): Installation and maintenance of the Sunspot 36 and 46 series lights. AeroLED's Holdings LLC - [STC SA02268CH](https://openairdocs.org/stc/SA02268CH): Installation of Airwolf Filter Corp. Air Oil Separator. Airwolf Filter Corporation - [STC SR00359BO](https://openairdocs.org/stc/SR00359BO): Installation of Parmetheus Plus LED PAR36 and PAR46 taxi and landing lights.. Whelen Aerospace Technologies - [STC SA01282NY](https://openairdocs.org/stc/SA01282NY): Installation of Airwolf remote mounted engine oil filter kit AFC-K015 on aircraft powered by Pratt & Whitney radial reciprocating engine Series R-985, R-1340 and R-1830.. Airwolf Filter Corporation - [STC SA01406NY](https://openairdocs.org/stc/SA01406NY): Installation of Airwolf remote mounted engine oil filter kit AFC-K017 on single and multi-engine fixed light aircraft and rotary wing. Airwolf Filter Corporation - [STC SR02394AK](https://openairdocs.org/stc/SR02394AK): Replacement of existing landing and/or hover light bulbs with Light Emitting Diode (LED) lighting system. Seaplanes North LLC - [STC SA2693NM](https://openairdocs.org/stc/SA2693NM): Installation of Electronics International digital volt/amp gauges and accessories.. Electronics International Inc. - [STC SA1626NM PAGE 2](https://openairdocs.org/stc/SA1626NM%20PAGE%202): Installation of Electronics Int'l Digital EGT/CHT Instruments and accessories. (201 Series). Electronics International - [STC SA4302NM](https://openairdocs.org/stc/SA4302NM): Installation of Electronics Int'l digital automatic engine analyzer.. Electronics International - [STC SH1599SO](https://openairdocs.org/stc/SH1599SO): Removal of main transmission oil cooler blower and associated parts.. Orlando Heli Airways Inc - [STC SH1524SO](https://openairdocs.org/stc/SH1524SO): Add approved fuels: unleaded automotive gasoline, 87 minimum antiknock index and leaded automotive gasoline, 88 minimum antiknock index (RON & MON)/2. Intermixing with aviation gasoline also approved.. Orlando Heli Airways Inc - [STC SH1072SO](https://openairdocs.org/stc/SH1072SO): Installation of dust boot retainer rings (in rotor head dampers).. Orlando Heli Airways Inc - [STC SA519WE](https://openairdocs.org/stc/SA519WE): Wheel adapters on Goodyear wheels3LMBM.. Lamb Robert P - [STC SA784WE](https://openairdocs.org/stc/SA784WE): Ceconite 101 covering of complete aircraft.. Cooper Engineering Corporation --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.