# TCDS TC 652: Lockheed Martin Aeronautics Company

- Type: Type certificate data sheet
- Status: Current
- Holder: Lockheed Martin Aeronautics Company
- Revision: 1
- Revised: July 23, 2012
- Product: Aircraft, Small Airplane
- Data sheet PDF: https://openairdocs.org/files/sha256/91/3b/913bcd787f9a85d1a2b32a7429be5ee7d9eed46fbf0193f64dea5900a80b1dfb
- FAA DRS: https://drs.faa.gov/browse/excelExternalWindow/999314CDC972AF5386257A4500475328.0001
- Page: https://openairdocs.org/tcds/TC%20652

## Models (1)

As the data sheet lists them.

- 12-B

## What the data sheet says

From the PDF's text layer, line by line; tables lose their columns. The PDF is the record.

```text
Page No. 1 2 3 4 5 
Rev. No. 1 1 1 1 1 
 
DEPARTMENT OF TRANSPORTATION 
FEDERAL AVIATION ADMINISTRATION 
652 
REVISION 1 
 
LOCKHEED 12-B 
   
July 23, 2012 
 
AIRCRAFT SPECIFICATION NO. 652 
 
This data sheet which is part of Type Certificate No. 652 prescribes conditions and limitations under which the product for which 
the type certificate was issued meets the airworthiness requirements of the Civil Air Regulations. 
 
Type Certificate Holder Lockheed Martin Aeronautics Company 
 86 South Cobb Drive 
 Marietta, GA 30063 
 
Type Certificate Holder Record Lockheed Aircraft Corporation 
  Burbank, California 
 
Model 12-B Designation 8 PCLM 
 
Engines 2 Wright R-975E-3 
  
Placard limits Maximum, except takeoff 34-5 in. Hg, 2,200 rpm (420 hp) 
 Takeoff (one minute) 36.5 in. Hg. 2,250 rpm (450 hp) 
  
Propellers 2 controllable metal (Ham Std., hubs 2D30, blades 6095-8; low pitch setting 16o)  
 152 lbs. (-84) (Maximum permissibl e propeller diameter 9 ft. 0 in.) 
  
Placard speeds (a) Never exceed 275 mph.   
 (b) Cruising 216 mph. 
 (c) Flaps extended 125 mph. 
  
Placard ceiling 5,500 ft. Usable in standard air at 8,650 lb s. at an indicated airspeed of 96 mph with either 
 engine inoperative and the inoperative prope ller idling in high pitch (1,100 rpm).  The 
 operating engine at full throttle at 2,200 rpm. 
  
Fuel capacity 200 gals. [4 tanks in wing:  2 fwd. of spar at 49 gals. each 62 lbs. (-15) and 2 aft of spar 
 at 51 gals. Each 60 lbs. (+17)] 
  
Oil capacity 14 gals. (2 tanks at 7 gals. each) 25 lbs. (-37)  
  
No. passengers 6 (See item 19) (Crew 2, -43) 
  
Baggage 450 lbs. [nose compt, 200 lbs. (-101) and aft of cabin compt. 250 lbs. (+111)] (See NOTE 1) 
  
Weights Empty              Use actual (approx. 5,800 lbs. (-10.77) as 8 PCLM with Class I items only) 
  Standard          8,650 lbs. (See NOTES 1 and 6) 
 Provisional      9,200 lbs. (See NOTES 1 and 6) 
  
C. G. limits (-16.3 and (+1.6) Level for we ighing on base line of main cabin windows.

652  2  
 
Specification basis Approved Type Certificate No. 652 
  
Serial Numbers 1228 and up eligible 
 
EQUIPMENT:  (Values in inches shown in parenthesis after each item represent horizontal arms to C.G. of the item, measured 
(minus) ahead and (plus) to the rear of the spar center line on under side of wing) (*Means net increase)  
 
Class I:  Required equipment which must be installed unless replaced by either Class II or III equivalent items (such items than  
to be marked “required” on the airworthiness certificate) subject to inspection and C.G. check. 
 
  1.  2 Engine ring cowls  75 lbs. (-65) 
  2.  2 Exhaust collector rings 105 lbs. (-44) 
  3.  2 Oil radiators (UAP 6”)  28 lbs. (-41) 
  4.  2 retracting landing lights in wing, 1 warning light in nose    8 lbs. (-19) 
  5.  2 flares and brackets (3 min.)  50 lbs. (-88) 
  6.  2 starters (electric )  64 lbs.  (-48) 
  7.  Battery (Exide 6-FHM-13-1  75 lbs. (-81) 
  8.  Generator (25 amp.)  21 lbs. (-54) 
  9.  Pressure fire extinguisher system (Alfite, 5 lb. bottle under co-pilot’s seat, or at rear of nose   
       baggage compt).  23 lbs. (-43) 
10.  30x13-6 wheels (Goodyear 6HBM)  62 lbs. (-18) 
11.  30X13-6 tires (HD 6-ply) and plain tubes  86 lbs. (-28) 
12.  Shock struts (Aerol SP-350L-12   89 lbs. (-28) 
13.  13.25 in. streamline tail wheel and tire  10 lbs. (+290) 
14.  Tail wheel shock strut (Aerol 300L)  20 lbs. (+282) 
15.  Instruments and Panel  50 lbs. (-72) 
16.  Wheel fenders    5 lbs. (-20) 
17.  (a) Residual fuel and oil in system  15 lbs. (-34) 
       (b) Old type dump valves and controls (Lockheed dwg. Nos. 68002, 68004) (see NOTE 6)   
18.  (a) Heater and ventilator  32 lbs. (+35) 
       (b) Toilet equipment  16 lbs. (+131) 
19.  Six standard passenger seats at 20 lbs. each (-11, -11, +31, +31, +64, +64) (See items 21 and 77)    
 
Class II:  Optional equipment which may be installed or removed, subject to inspection and check of C.G. limits. 
 
21.  Standard passengers chair removed; deduct 20 lbs. each (Roman numerals in parenthesis signify   
       Number of seats removed)  (See items 19 and 77)   
22.  Extra fire extinguisher   7 lbs. (-50) 
23.  Cockpit partition and door assembly  25 lbs. (-50) 
24.  Constant speed propeller control (Low pitch setting 11o or 11 1/2o  for 6095-8 blades  20 lbs (-64) 
25.  Exhaust gas analyzer (Cambridge)  12 lbs. (-45) 
26.  Pesco vacuum pumps (two)  10 lbs. (-59) 
27.  Vacuum pumps (two) (Eclipse or Romec)  14 lbs. (-59) 
28.  Couch – three place  81 lbs. (+42) 
29.  Card table    8 lbs, (+140) 
30.  Buffet and refrigerator (See NOTE 1b)   42 lbs. (-17) 
31. Omitt 
32. ed 
  
32.  Abrasion Strips (tail surfaces (L.E.)    5 lbs. (+250) 
33.  Generator, 50 amp.   36 lbs. (+54) 
34.  (a) Antenna reel (H & K)   10 lbs. (+290) 
       (b) Antenna     5 lbs. (+20) 
35.  Automatic pilot (Sperry) 100 lbs. (-64) 
36.  Battery (Prestolite R-1213-G   91 lbs. (-81) 
37.  Radio receiver (RCA)   25 lbs. (-14) or 
(-43) 
39.  Omitted   
41.  Radio (complete 2-way W.E.) 160 lbs. (-29) 
42.  Omitted

3 652 
43.  Omitted   
44.  Omitted   
45.  Omitted   
46.  Oil immersion heaters   6 lbs.  (-37) 
47.  De-icing equipment (fixed portion 30 lbs., removable 65 lbs.)  (See NOTE 4)  95 lbs. (-13) 
48.  Radio compass and loop  45 lbs. (-24) 
49.  Extra antennae  10 lbs.  (+50) 
50.  Abrasion strips on lower fins     2 lbs. (+270) 
51.  Carpet (cabin)   23 lbs. (+50) 
52.  Radio Receivers (2 TCA (AVR-7)   46 lbs. (-40) 
53.  (a)  Radio transmitter (RCA (AVT-12)   80 lbs. (+85) 
       (b)  Radio transmitter (RCA AVT-12)   80 lbs. (-17) 
       (c)  Radio transmitter (RCA (AVT-12)   80 lbs. (-85) 
55.  Radio compass and loop (RCA AVR-8 series)   63 lbs. (-22) 
56.  Radio (complete 2-way W. E. ) (one receiver 137 lbs. (-31) 
58.  Two electric fans (cabin)     4 lbs. (+50) 
59.  Brake Controls dual set – co-pilot     4 lbs. (-74) 
60.  Omitted   
61.  Omitted   
62.  30x13-6 cactus proof tire liners    20 lbs. (-28) 
63.  Omitted   
64.  Tail wheel lock    3 lbs (-50) 
65.  Two foot rests  15 lbs. (+37) 
66.  Loading step    4 lbs. (+88) 
67.  Propeller spinners   16 lbs. (-84) 
68.  Omitted   
69.  Omitted   
70.  Cactus proof tail wheel and tire liner     8 lbs. (+290) 
71.  Antenna reel and fairlead     7 lbs. (-47) 
72.  Omitted   
73.  Special cabin upholstery    10 lbs. (+20) 
74.  Omitted   
75.  Cannon tuning unit     4 lbs. (+295) 
76.  Revised brake control system in accordance with data submitted June 18, and June 21, 1937 No 
weight 
change  
 
77.  Standard Model 14 chair installed at 53 lbs. each  (Roman numerals in parenthesis signify number of 
seats installed) (See items 19 and 21) 
  
78.  Propeller spinners (Heavier type)   22 lbs. (-84) 
79.  Closeable dump valves, controls and discharge chutes (See NOTE 6)   14 lbs.* (+8) 
80.  Heavy type nose baggage compt. Flooring   10 lbs.* (-101) 
81.  Revised empennage assembly with dynamically balanced rudders (Lockheed Dwg. No. 63012)   55 lbs.* (+273) 
82.  Aileron 100% static balance (Lockheed Dwg. 62002G)   23 lbs.* (+26) 
85.  Miscellaneous items as noted in approved weight and balance report.   
86.  Zeiss special camera installation   10 lbs. (+87) 
 
Class III:  Optional equipment which may be installed or removed subject to insp ection only, except when the airplane is alread y 
equipped for the effect on C.G. limits of th e Class III item installation.  (Note that when any Class II item is installed, wit h Class 
III items are in effect Class II items) 
 
38.  (a) Fuel capacity increased 49 gals. (One fuselage tank Lockheed Dwg. No. 69350   40 lbs. (-16) 
       (b) Oil capacity 19 gals. (9 ½ gals. Tanks, Lockheed Dwg. Nos. 64331 or 63429 in each nacelle 
             Replacing standard 7 gal. tanks) 
No 
weight 
change 
 
40.  Radio cabinet   20 lbs. (-15) 
54.  Fuel capacity increased 96 gals.   80 gals. (-16) 
57.  Map case   16 lbs. (-15) 
84.  Wing fuel tank installation (Lockheed Dwg. No. 68007 (4 tanks in wing:  2 fwd. of spar at 49 gals.  
        And 2 aft of spar at 50 gals.)                                                                                              Net 
increase 
 
  62 lbs. 
 
(+0.5)

652  4  
 
NOTE 1. (a) Weight and balance report including list of equipm ent included in certificated weight empty, and loading  
      schedule when necessary must be submitted for each aircraft with original inspector’s report and each  
      subsequent report covering change in equipment.  (This note applies when standard weight exceeds 8,450 lbs. 
  
(b)  When item 30 is installed, baggage may be increased 45 lbs.  (capacity of refrigerator). 
  
 
NOTE 1. Weight and balance report including list of equipm ent included in certificated weight empty, and loading 
instructions when necessary, must be submitted for each  aircraft with original inspector’s report and each 
subsequent report covering changes in equipment. 
 
NOTE 2. Omitted. 
 
NOTE 3. Eligible for export, at standard weight, as follows  subject to inspection for required equipment:  (August 1, 1939) 
 (a)  Canada 
       - Landplane – eligible. 
       -  Skiplane – not eligible.  
(b)  All other countries except Australia. 
 
NOTE 4. Include weight of de-icer, when carried, in empty weight- no deduction – and add as terisk by standard weight 
value referring to the following note to be added to airwor thiness certificate:  “Standard weight may be increased 
52 lbs. when complete de-icer is installed.” 
 
NOTE 5. Same as Model 12-A (ATC 616) except for change in engines. 
 
NOTE 6. A.  If provisions other than Item 79 are made fo r dumping, the fuel dump valves shall be made positively 
      Inoperative. 
 B.  If Item 79 (which complies with (EI-11c) is installed,  the airworthiness certificate shall incorporate one of the 
following statements, as the case may be: 
 
 (1)  Non-Airline Carrier.  “Fuel shall not be dumped except in accordance with the provisions of Civil Air  
Regulation 60.900.” 
 (2)  Airline Carrier: 
         (a)  With authorized weight in excess of sta ndard – “landing shall not be made at a weight in excess of  
              standard except in accordance with Civil Air Regulation 61.7811.  Fuel shall not be dumped except  
              in accordance with Civil Air Regulation 61.7811 and then only if the pilot deems it safer than landing 
              at a weight in excess of standard.” 
 (b)  With authorized weight not in excess of standard “Fuel shall not be dumped except in accordance 
With Civil Air Regulation 61.7811. 
 
INSPECTORS MUST REPORT COMPLIANCE WITH THE FOLLOWING SPECIAL NOTES IN ACCORDANCE WITH DI-
15: 
 
SPECIAL NOTE 1.  (Annual inspection required – February 7, 1938, revised August 1, 1939) 
 
Make sure that the old type bronze flap actuating screw and steel nut have been replaced with new type steel screw and bronze 
nut.  (This note applies to Serial Nos. 1228 to 1247, inclusive, only.) New parts have been furnished all owners. 
 
SPECIAL NOTE 2.  (Annual inspection required – February 7, 1938, revised August 1, 1939) 
 
In all airplanes up to and including serial No. 1240, ascertain that a new fuselage bulkhead or bulkhead reinforcements (two in 
latter case – one left – one right – in vicinity of stabilizer front spar bulkhead joint) have been installed in the plane of the 
fuselage-stabilizer front spar bulkhead joint) have been installed in the plane of the fuselage-stabilizer front spar attachment. 
 
The stabilizer front spar must also be reinforced by plates connecting the open ends of the new bulkhead or bulkhead 
reinforcement. 
 
The stabilizer rear spar must be reinforced in a similar manner to front spar by the addition of reinforcing plates (one left, one 
right).

5 652 
Installation instructions Nos. 4, 5, 6, and 7, together with reinforcement parts covering “Bulkhead Replacement” or “Bulkhead 
Reinforcement” and also “Stabilizer Front and Rear Spar Reinforcement” were forwarded to owners by the manufacturer. 
 
SPECIAL NOTE 3.  (Annual inspection required – August 9, 1938, revised August 1, 1939) 
 
In airplanes serial Nos. 1201 to 1250, inclusive, it is necessary to reinforce the front spars and forward rib flanges of the ailerons 
in the vicinity of the counter weight attachments.  The reinforcement should be fabricated and installed in accordance with 
Lockheed Dwg. No. 62211. 
 
SPECIAL NOTE 4.  (Inspection required on regular itinerary – May 18, 1939, revised June 24, 1939) 
 
In all airplanes up to and including serial No. 1271, ascertain that braces in accordance with Lockheed Dwg. No. 61143 have 
been added to the rear spar and flap actuating mechanism.  Braces consist of additional extrusion on front face of spar opposite 
first roller bracket for flap tube, a brace tube to the first roller from the top of the spar, and two brace tubes to the thrust bearing 
just inboard of the actuating screw. 
-END-
```

## ADs (1, in force first)

- [AD 2023-10-02](https://openairdocs.org/ad/2023-10-02): Indicating/Recording System, Navigation · Boeing 18, 23, 35 and 1,060 more. Effective May 26, 2023

## STCs approved under this data sheet (1)

- [STC SA04652CH](https://openairdocs.org/stc/SA04652CH): To allow use of 100R grade aviation fuel meeting Swift Fuel, LLC specification. Swift Fuels LLC

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain.
