AC 00-45F

Change 1Historical

Advisory circular · Aviation Weather Services

Approved
July 1, 2008
Last reviewed
September 13, 2024
This change
This entire document series, all through the H Revision, is canceled.
Cancels
AC00-45F
Cancelled by
AC00-45F CHG 2
Family
AC 00-45 · 10 versions
Revision
F, change 1
14 CFR parts
1

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 106–117
Page 118Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-8

5.1.2.3.12 Swell Information Swell direction, period, and height are represented in the surface observations by a 6-digit code.

The first two digits represent the swell direction, the middle digits describe the swell period (in seconds), and the last two digits are the swell's height (in half meters).

090703 09 - The swell direction is from 90 degrees (i.e. it is coming from due east).

07 - The period of the swell is 7 seconds.

03 - The height of the swell is 3 half meters.

271006 27 - The swell direction is from 270 degrees (due west).

10 - The period is 10 seconds.

06 - The height of the swell is 6 half meters.

5.1.2.3.13 Wave Information Period and height of waves are represented by a 5-digit code. The first digit is always 1. The second and third digits describe the wave period (in seconds), and the final two digits give the wave height (in half meters).

10603 1 - A group identifier. The first digit will always be 1.

06 - The wave period is 6 seconds.

03 - The wave height is 3 half meters.

10515 1 - The group identifier again.

05 - The wave period is 5 seconds.

15 - Wave height is 15 half meters.

In some charts by the OPC, only the wave height (in feet) is plotted.

5.1.2.4 Analyses Isobars, pressure systems, and fronts are the most common analyses depicted on surface analysis charts.

5.1.2.4.1 Isobars An isobar is a line of equal or constant pressure commonly used in the analysis of pressure patterns.

On a Surface Analysis Chart, isobars are solid lines usually spaced at intervals of 4 millibars (mb). Each isobar is labeled. For example, 1032 signifies 1,032.0 mb and 992 signify 992.0 mb.

METAR/SPECI (Section 2.1) reports pressure in hectopascals. However, one millibar is equivalent to one hectopascal, so no conversion is required.

Page 119Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-9

5.1.2.4.2 Pressure Systems On a Surface Analysis Chart, a High (H) is a maximum of atmospheric pressure, while a Low (L) is a minimum of atmospheric pressure. Central pressure is the atmospheric pressure located at the center of a High or Low. In general, the central pressure is the highest pressure in the center of a High and the lowest pressure at the center of a Low. The central pressure is denoted near each pressure center.

A trough or an elongated area of low atmospheric pressure is denoted by dashed lines and identified with the word TROF. A ridge or an elongated area of high atmospheric pressure is denoted by saw-toothed symbols. Ridges are rarely denoted on charts produced by the HPC.

Tropical storms, hurricanes, and typhoons (See Figure 5-2) are low-pressure systems with their names and central pressures denoted.

5.1.2.4.3 Fronts The analysis shows positions and types of fronts by the symbols in Figure 5-2. The symbols on the front indicate the type of front and point in the direction toward which the front is moving.

Two short lines across a front indicate a change in front type.

Figure 5-10. HPC Surface Analysis Chart – North America Example

Page 120Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-10

Figure 5-11. HPC Surface Analysis Chart - Contiguous U.S. Example

Figure 5-12. HPC Surface Analysis Chart - Northeast U.S. Example

Page 121Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-11

Figure 5-13. HPC Surface Analysis Chart for Aviation Interests – Contiguous U.S. Example

Figure 5-14. HPC Surface Analysis Chart for Aviation Interests – South central U.S. Example

Page 122OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1

5.1.3 OPC and WFO Honolulu Surface Analysis Charts The Ocean Prediction Center (OPC) in Camp Spring, Maryland is responsible for the Atlantic and Pacific Oceans north of 30°N latitude. The charts are found at:

• http://www.opc.ncep.noaa.gov/ The Weather Forecast Office in Honolulu, Hawaii (WFO HNL) is responsible for the tropical Pacific Ocean, south of 30°N latitude and west of 160°E longitude. The charts are found at:

• http://www.prh.noaa.gov/hnl/pages/analyses.php

5.1.3.1 Issuance The Ocean Prediction Center (OPC) produces surface analysis charts for the Atlantic and Pacific Oceans north of 30°N latitude four times daily (Table 5-2). The Weather Forecast Office in Honolulu, Hawaii (WFO HNL) issues surface analysis charts for the tropical Pacific Ocean, south of 30°N latitude and west of 160°E longitude four times daily. Surface analysis charts for the North Pacific are jointly issued by both offices.

Table 5-2. OPC and WFO Honolulu Surface Analysis Charts Issuance Schedule UTC 00 06 12 18

5.1.3.2 Analysis Symbols Figure 5-15 shows analysis symbols used on OPC and WFO HNL surface analysis charts.

H 30 MODERATE ICING TEXT ABBREVIATIONS:

1024 AND PRES IN MBS 24HR HIGH PRES MOVI O HEAVY ICING STORM = 48-63 KT GALE = 34-47 KT HIGH PRES CENTER WIND BARBS: HURCN => 64 KT WITH PRES IN MBS = 5 KT KI = KNOTS, G = GUSTS 99 HR = HOUR 10 KT MBS = MILLIBARS LOW PRES 996 CENTER AND PRES 24HR LOW PRES MOVI IN MBS = 20 КТ 15 KT PRES = PRESSURE HURCN = HURRICANE DSIPT = DISSIPATED WITH PRES IN MBS = 25 KT SINRY = STATIONARY = 35 KT WKNG = WEAKENING COLD FRONT = 50 кТ RPDLY = RAPIDLY FRMG = FORMING = 60 KT MOVG = MOVING WARM FRONT - = 65 KT TROF = TROUGI AlL =75 KT TRPCL = TROPICAI INLD = INLANI SINRY FRONT L = 100 KT DVLPG = DEVELOPING OCCLUDED FRONT L =110 KT COMB = COMBINING DCRS = DECREASING RIDGE LIL = 120 KT INCR = INCREASING INTSFYG = INTENSIFYING ) HURCN TROF • HURCN SOUTHERN HEMISPHERE PSN = POSITION Q TRPCL STORM I TROPICAL DEPRESSION « TROPICAL DISTURBANCE Figure 5-15. OPC and WFO HNL Surface Analysis Chart Symbols AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-12

Page 123Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-13

Figure 5-16. WFO HNL Surface Analysis Chart – North Pacific Example

5.1.3.3 Wave Information Period and height of waves are represented by a 5-digit code. The first digit is always 1. The second and third digits describe the wave period (in seconds), and the final two digits give the wave height (in half meters). Below are two examples:

10603 1 - A group identifier. The first digit will always be 1.

06 - The wave period is 6 seconds.

03 - The wave height is 3 half meters.

10515 1 - The group identifier again.

05 - The wave period is 5 seconds.

15 - Wave height is 15 half meters.

In certain charts by the OPC, only the wave height (in feet) is plotted.

5.1.3.4 Analyses Isobars, pressure systems, and fronts are the most common analyses depicted on the surface analysis charts.

5.1.3.4.1 Isobars An isobar is a line of equal or constant pressure commonly used to analyze pressure patterns.

Page 124Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-14 On a Surface Analysis Chart, isobars are solid lines usually spaced at intervals of 4 millibars (mb). Each isobar is labeled. For example, 1032 signifies 1,032.0 mb and 992 signify 992.0 mb.

METAR/SPECI (Section 2.1) reports pressure in hectopascals. However, one millibar is equivalent to one hectopascal, so no conversion is required.

5.1.3.4.2 Pressure Systems On a Surface Analysis Chart, a High (H) is a maximum of atmospheric pressure, while a Low (L) is a minimum of atmospheric pressure. Central pressure is the atmospheric pressure at the center of a High or Low -- the highest pressure in a High and the lowest pressure in a Low. The central pressure is denoted near each pressure center. Tropical storms, hurricanes, and typhoons (See Figure 5-15) are low-pressure systems with their names and central pressures denoted.

A trough or an elongated area of low atmospheric pressure is denoted by dashed lines and identified with the word TROF. A ridge or an elongated area of high atmospheric pressure is denoted with saw-toothed symbols. Ridges are rarely denoted on charts produced by the HPC.

5.1.3.4.3 Fronts The analysis shows positions and types of fronts by the symbols in Figure 5-15. The symbols on the front indicate the type of front and point in the direction toward which the front is moving.

Two short lines across a front indicate a change in front type.

5.1.4 TPC Surface Analysis Charts The Tropical Prediction Center (TPC) in Miami, Florida is responsible for the tropical regions of the western hemisphere south of 30oN latitude and east of 160oE longitude. The surface analysis chart is located at:

http://www.nhc.noaa.gov/marine_forecasts.shtml

5.1.4.1 Issuance The Tropical Prediction Center (TPC) issues Surface Analysis Charts for tropical regions of the western hemisphere south of 30oN latitude and east of 160oE longitude four times a day (Table 5-3).

Table 5-3. TPC Surface Analysis Charts Issuance Schedule Valid Time (UTC) 00 06 12 18

5.1.4.2 Analysis Symbols Figure 5-17 shows analysis symbols used on TPC surface analysis charts.

Page 125OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 †1024 TITH PRES IN MILLIBARS CENTER OF HIGH PRES TRPCL × 999 WITH PRES IN MILLIBARS CENTER OF LOW PRES DEPRESSION STORM (TS) — 10 KT 5 KT COLD FRONT • HURRICANE (HRON) •— 15 KT 20 KT L 25 КТ WARM FRONT P CONVECTION GALE OR TRPCL STORM W- 35 KT STATIONARY FRONT TRPCL - 50 KT STORM WAVE Ille 74 KT HRCN

OCCLUDED FRONT TEXT ABBREVIATIONS M 105 KT DRY LN KT KNOTS 24 HR HIGH PRES

FT FEET MOVEMENT " SQUALL LN NIM NAUTICAL MILES GUSTS

TROF LN HRCN - HURRICANE TRPCL- TROPICAL 24 HR LOW PRES

PRES - PRESSURE MOVEMENT

RIDGE AXIS IN TROF - TROUGH LINE

MONR - SOAIIONARY MOVING Figure 5-17. TPC Surface Analysis Chart Symbols SON 1028 04 1026 1026 | 24 SINRY 30м 20 TROF 1016) 20 08 08- 12 09 12 1007 XX

IPC PSN Se 120KT ITCZI 994 • ITCZ.

N 35 30 0900T 5055КГ 6 65К PS% los .

16 16 130W 120W 110W 100W 90K .... 80W. 16 10y 16 G0H 50W 30W 20W O6Z TROPICAL SURFACE ANALYSIS SALLOP LINES2004 TROPICAL PREDICTION CENTER SSUED: FLORIDA THUNDERSTORMS: COLLABORATING CENTERS! ANALYST: FORMOSA TPČ OPC HPC HFO Figure 5-18. TPC Tropical Surface Analysis Chart Example

5.1.4.2.1 Wind Wind is plotted in increments of 5 knots (kts). The wind direction is in "true" degrees and is depicted by a stem (line) pointed in the direction from which the wind is blowing. The wind speed is determined by adding up the value of the flags (50 kts), lines (10 kts), and half-lines (5 kts), each of which has the following individual values:

AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-15

Page 126Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-16

A single circle over the station with no wind symbol indicates a calm wind.

Figure 5-19 shows some sample wind symbols:

Figure 5-19: TPC Surface Analysis Chart Wind Plotting Model

5.1.4.3 Analyses Isobars, pressure systems, and fronts are the most common analyses depicted on the surface analysis charts.

5.1.4.3.1 Isobars An isobar is a line of equal or constant pressure commonly used to analyze pressure patterns.

On a Surface Analysis Chart, isobars are solid lines usually spaced at intervals of 4 millibars (mb). Each isobar is labeled. For example, 1032 signifies 1,032.0 mb and 992 signify 992.0 mb.

METAR/SPECI (Section 2.1) reports pressure in hectopascals. However, one millibar is equivalent to one hectopascal, so no conversion is required.

5.1.4.3.2 Pressure Systems On a Surface Analysis Chart, a High (H) is a maximum of atmospheric pressure, while a Low (L) is a minimum of atmospheric pressure. Central pressure is the atmospheric pressure at the center of a High or Low -- the highest pressure in a High and the lowest pressure in a Low. The central pressure is denoted near each pressure center. Tropical storms, hurricanes, and

Page 127Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-17 typhoons (See Figure 5-17) are low-pressure systems with their names and central pressures denoted.

A trough or an elongated area of low atmospheric pressure is denoted by dashed lines and identified with the word TROF. A ridge or an elongated area of high atmospheric pressure is denoted by saw-toothed symbols. Ridges are rarely denoted on charts produced by the TPC.

5.1.4.3.3 Fronts The analysis shows positions and types of fronts by the symbols in Figure 5-17. The symbols on the front indicate the type of front and point in the direction toward which the front is moving.

Two short lines across a front indicate a change in front type.

5.1.5 Unified Surface Analysis Chart The Unified Surface Analysis Chart is a composite of all the surface analysis charts produced by HPC, OPC, TPC and WFO Honolulu. It contains an analysis of isobars, pressure systems and fronts.

5.1.5.1 Issuance The chart is issued four times daily by the OPC (see Table 5-4).

Table 5-4. Unified Surface Analysis Chart Issuance Schedule Valid Time (UTC) 00 06 12 18

Figure 5-20. Unified Surface Analysis Chart Example

5.1.5.2 Analysis Symbols Figure 5-21 shows analysis symbols used on the Unified Surface Analysis charts.

Page 128Open in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1 AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-18

Figure 5-21. Unified Surface Analysis Chart Symbols

5.1.5.3 Analyses Isobars, pressure systems, and fronts are the most common analyses depicted on the surface analysis charts.

5.1.5.3.1 Isobars An isobar is a line of equal or constant pressure commonly used to analyze pressure patterns.

On a Surface Analysis Chart, isobars are solid lines usually spaced at intervals of 4 millibars (mb). Each isobar is labeled. For example, 1032 signifies 1032.0 mb and 992 signify 992.0 mb.

METAR/SPECI (Section 2.1) reports pressure in hectopascals. However, one millibar is equivalent to one hectopascal, so no conversion is required.

5.1.5.3.2 Pressure Systems On a Surface Analysis Chart, a High (H) is a maximum of atmospheric pressure while a Low (L) is a minimum of atmospheric pressure. Central pressure is the atmospheric pressure at the center of a High or Low -- the highest pressure in a High and the lowest pressure in a Low. The central pressure is denoted near each pressure center. Tropical storms, hurricanes, and typhoons (See Figure 5-21) are low-pressure systems with their names and central pressures denoted.

On a Surface Analysis Chart, a trough is an elongated area of relatively low atmospheric pressure, while a ridge is an elongated area of relatively high atmospheric pressure. Troughs are denoted by dashed lines and identified with the word TROF. Ridges are denoted by sawtoothed symbols. Ridges are rarely denoted on charts produced by the HPC.

5.1.5.3.3 Fronts The analysis shows positions and types of fronts by the symbols in Figure 5-21. The symbols on the front indicate the type of front and point in the direction toward which the front is moving.

Two short lines across a front indicate a change in front type.

Page 129OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45F, Revision 1

5.1.6 AAWU Surface Charts The Alaskan Aviation Weather Unit (AAWU) in Anchorage, Alaska is responsible for the state of Alaska. The surface analysis chart is located at:

http://aawu.arh.noaa.gov/surface.php

5.1.6.1 Issuance The AAWU issues Surface Analysis Charts 4 times daily for the state of Alaska. The valid times are shown in Table 5-5.

Table 5-5. AAWU Surface Analysis Issuance Schedule Valid Time 00 06 12 18 (UTC)

5.1.6.2 Analysis Symbols The symbols (Figure 5-22) used on the Alaskan Surface Analysis Chart are similar to those found on the HPC Surface Analysis chart. However, since the Alaskan Surface Analysis chart is in black and white all of the symbols are black and white as well.

A Key to Symbols used on the AAWU Graphic Products

- Cold Front H 1032 - High Pressure Center Pressure in millibars

- Warm Front L 988 - Low Pressure Center

- Occluded Front Pressure in millibars

- Stationary Front

- Occasional or greater

- Trough Precipitation

- Ridge

- Fog - Freezing Rain - Mixed Rain/Snow аю - Haze - Freezing Drizzle - Rain Showers

- Smoke - Light Icing - Snow Showers ‡→ - Drifting Snow - Moderate Icing - Rain/Snow Showers

- Sandstorm - Severe Icing K -Thunderstorm

• - Drizzle * - Snow A - Light Turbulence

• - Rain > - Ice Crystals A - Moderate Turbulence A - Ice Pellets A - Severe Turbulence Figure 5-22. AAWU Surface Analysis Chart Symbols AC 00-45F (July 2008) Section 5: Graphical Observations and Derived Products Page 5-19