AC 00-45G

Change 1Historical

Advisory circular · Aviation Weather Services

Approved
July 29, 2010
Last reviewed
September 13, 2024
This change
This entire document series, all through the H Revision, is canceled.
Cancels
AC00-45G
Cancelled by
AC00-45G CHG 2
Family
AC 00-45 · 10 versions
Revision
G, change 1
14 CFR parts
1

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 325–336
Page 337OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) By FAA policy CIP is a Supplementary Weather Product for enhanced situational awareness only and must be used with one or more primary products (safety decision) such as an AIRMET or SIGMET (see AIM 7—1—3).

Maximum icing severity (prob>25%) (1000 ft. MSL to FL300) Analysis valid 1700 UTC Mon 27 Nov 2006 None <25⅞ Trace Light Moderate Hedyy

4) Trace-Light V Light-Moderate 1) Moderdte-Savare Icing PIREP Symbols W Trace 4) Light H' Moderate Yul Severa Figure 9-17. CIP Icing Severity Probability >25% Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. A gray color is used to mask the intensity pixels where the probability of icing is 25% or less.

9.3.2.7 Icing Severity - Probability > 50% The Icing Severity - Probability > 50% product (Figure 9-18) depicts, at a single altitude, where the probability of the indicated icing intensity 51 to 100 percent. Icing intensity is displayed using icing intensity categories: trace, light, moderate and heavy.

Section 9: Supplementary Products Page 9-19

Page 338OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) By FAA policy CIP is a Supplementary Weather Product for enhanced situational awareness only and must be used with one or more primary products (safety decision) such as an AIRMET or SIGMET (see AIM 7—1-3).

Icing severity (prob>50%) at 3000 ft. MSL Analysis valid 1500 UTC Mon 27 Nov 2006 terrain None <50% Trace Light Moderate Heavy @ Negative 4J Trace-Light I Light-Moderate 1I Moderate-Savare Icing PIREP Symbols W Trace Al Light Y Severe Figure 9-18. CIP Icing Severity Probability > 50% Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. Brown regions indicate where higher-elevation terrain extends above the altitude of the particular graphic. A gray color is used to mask the intensity pixels where the probability of icing is 50% or less.

9.3.2.8 Icing Severity - Probability > 50% - Maximum The Icing Severity - Probability > 50% - Maximum product (Figure 9-19) depicts, at all altitudes from 1,000 feet MSL to FL300, where the probability of the indicated icing intensity is 51 to 100 percent. Icing intensity is displayed using icing intensity categories: trace, light, moderate and heavy.

Page 9-20 Section 9: Supplementary Products

Page 339OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) dy FAR policy LIP is a supplementary heather Product tor enhanced situational awareness only and must be used with one or more primary products (safety decision) such as an AIRMET or SIGMET (see AIM 7-1-3).

Maximum icing severity (prob>50%) (1000 fl. MSL to FL300) Analysis valid 1700 UTC Mon 27 Nov 2006 None <50% Trace Light Moderate Heavy Ul Trace-Light Nu Light-Moderate I Moderate-Severa Icing PIREP Symbals Lf Trace YuLight /Moderate Yul Severe Figure 9-19. CIP Icing Severity Probability > 50% - Max Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. A gray color is used to mask the intensity pixels where the probability of icing is 50% or less.

9.3.2.9 Icing Severity plus Supercooled Large Droplets (SLD) The Icing Severity plus Supercooled Large Droplets (SLD) product (Figure 9-20) depicts, at a single altitude, the intensity of icing expected as well as locations where a threat for SLD exists.

SLD is defined as supercooled water droplets larger than 50 micrometers in diameter. These size droplets include freezing drizzle and/or freezing rain aloft. SLD, which are outside the icing Section 9: Supplementary Products Page 9-21

Page 340OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) certification envelopes (FAR Part 25 Appendix C), can be particularly hazardous to some aircraft.

Icing intensity is displayed using icing intensity categories: trace, light, moderate and heavy.

By FAA policy CIP is a Supplementary Weather Product for enhanced situational avareness only and must be used with one or more primary products (safety decision) such as an AIRMET or SIGMET (see AIM 7—1—3).

Icing severity at 3000 ft. MSL Analysis valid 1800 UTC Mon 27 Nov 2006 SLD threat terrain None Trace Light Moderate Heavy ø Negative If Trace-Light W| Light-Moderate W! Maderate-Savare cing PIREP Symbols W Trace Ll Light If Moderate H/ Severa Figure 9-20. CIP Icing Severity plus Supercooled Large Droplets (SLD) Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. Brown regions indicate where higher-elevation terrain extends above the altitude of the particular graphic.

Locations where a threat for SLD exists are depicted with red hatching.

9.3.2.10 Icing Severity plus Supercooled Large Droplets (SLD) - Maximum Page 9-22 Section 9: Supplementary Products

Page 341OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) The Icing Severity plus Supercooled Large Droplets (SLD) product (Figure 9-21) depicts at all altitudes, between 1,000 feet MSL and FL300, the intensity of icing expected as well as locations where a threat for SLD exists.

SLD is defined as supercooled water droplets larger than 50 micrometers in diameter. These size droplets include freezing drizzle and/or freezing rain aloft. SLD, which are outside the icing certification envelopes (FAR Part 25 Appendix C), can be particularly hazardous to some aircraft.

ly FAA policy CIP is a Supplementary Meather Product for enhanced situational awareness only and must bi sed mith one or more primary products (safety decision) such as an AIRMET or SIGMET (see AIM 7-1-3) Maximum icing severity (1000 ft. MSL to FL300) Analysis valid 1500 UTC Mon 27 Nov 2006 SLD threat None Trace Light Moderate Heavy

4) Trace-Light W Light-Maderate \ Moderate-Savare cing PIREP Symbols W Trace Yes Light y Moderate # Severe Figure 9-21. CIP Icing Severity plus Supercooled Large Droplets (SLD) - Max Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate Section 9: Supplementary Products Page 9-23

Page 342Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-24 Section 9: Supplementary Products where no probability of icing exists and, therefore, no intensity is necessary. Locations where a threat for SLD exists are depicted with red hatching.

9.3.3 Strengths and Limitations

9.3.3.1 Strengths The CIP product suite is updated hourly and provides a diagnostic tool to assist in determining the probability for icing, the intensity of icing and the threat for SLD.

9.3.3.2 Limitations Actual icing severity may be different than what is depicted on the CIP graphics and plotted PIREPS because:

Different aircraft types experience different severities of icing in the same atmospheric environments. Severity definitions are currently pilot-based and thus are a function of the aircraft type, flight phase (takeoff/landing, cruise, etc.), aircraft configuration, as well as the pilot’s experience and perception of the icing hazard.

Assessing the amount and drop size of supercooled liquid water (SLW) in the atmosphere is difficult.

The Icing Severity products depict the severity of the meteorological icing environment and not the resultant icing that may occur on the aircraft.

9.3.4 Uses The CIP Icing Probability product can be used to identify the current three-dimensional probability of icing.

The CIP Icing Severity product can be used to determine the intensity of icing. The CIP Icing Severity – Probability > 25% or Probability > 50% depicts the probability of a given intensity of icing occurring.

Finally the Icing Severity plus SLD product can help in determining the threat of SLD which is particularly hazardous to some aircraft.

Icing PIREPs are plotted on single altitude graphics if the PIREP is within 1,000 feet of the graphic’s altitude and has been observed within 75 minutes of the chart’s valid time. On CIP Max product, PIREPs for all altitudes (i.e. 1,000 feet MSL to FL300) are displayed. However, negative reports of icing are not plotted on the CIP Max product in an effort to reduce clutter.

The PIREP legend is located on the bottom of each graphic.

Page 343Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Section 9: Supplementary Products Page 9-25

9.4 Forecast Icing Potential (FIP) The Forecast Icing Potential (FIP) provides a three-dimensional forecast of icing potential (or likelihood) using numerical weather prediction model output (Figure 9-17). The FIP product suite is automatically generated with no human modifications. It may be used as a higher resolution supplement to AIRMETs and SIGMETs but is not a substitute for them. It is authorized for operational use only by meteorologists and dispatchers. The forecast area covers the 48-contiguous states, much of Canada and Mexico and their respective coastal waters.

9.4.1 Issuance The FIP is issued every hour and generates hourly forecast for 3 hours into the future. For example, forecasts issued at 1300Z would be valid for 1400Z, 1500Z and 1600Z. Six-, 9-, and 12-hour forecasts are issued every three hours beginning at 00Z. For example, a forecast suite issued at 0300Z would have valid times at 0900Z, 1200Z and 1500Z respectively. The product is issued by the Aviation Weather Center (AWC) and is available through the Aviation Digital Data Service (ADDS) web site at: http://adds.aviationweather.noaa.gov/icing/icing_nav.php.

9.4.2 Content The FIP forecasts the likelihood of icing from super-cooled liquid water droplets. The likelihood field ranges from 0 (no icing) to 100 (icing likely). The scale depicts likelihood of icing using “cool” and “warm” colors, with warmer colors indicating a higher likelihood of icing. Regions depicted in white indicate zero icing potential according to the CIP. Brown regions indicate areas of terrain.

The scale is not calibrated as a true probability value. It does, however, have value in pointing out differences in the likelihood of encountering icing at a given location. For example, a value of 70 does not indicate there is a 70 percent chance of encountering icing. However, when comparing it to other higher or lower values will indicate if there is a greater or lesser likelihood of encountering icing. No information is provided as to the severity of icing and none should be inferred. FIP output is available for 1,000 foot vertical intervals. ADDS displays every third level except on the Flight Path Tool which provides access to all levels.

Page 344Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-26 Section 9: Supplementary Products

Figure 9-22. FIP Example

9.4.3 Strengths and Limitations

Strengths

 The FIP can be used to help determine the forecast for potential for icing through the entire vertical depth of the atmosphere.

 The product is updated hourly.

Limitations

 The product does not display any information about the severity of icing.

 The product only displays the forecast potential for icing, not the absolute probability.

 It is only approved for use by meteorologists and dispatchers.

Page 345Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Section 9: Supplementary Products Page 9-27

 The product is generated without human modification. Therefore, the forecasts are only as accurate the computer model output used to create them.

9.4.4 Use The FIP is primarily used to help determine the likelihood of icing at the specified forecast valid times.

Page 346Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-28 Section 9: Supplementary Products

9.5 Graphical Turbulence Guidance (GTG-2) The Graphical Turbulence Guidance (GTG-2) graphics are computer-generated fourdimensional forecasts of information related to the likelihood of encountering Clear Air Turbulence (CAT) associated with upper-level fronts and jet streams. It is not intended to predict turbulence associated with convection and thunderstorm clouds or breaking mountain waves.

The product provides forecasts for the 48 contiguous United States, much of Canada and Mexico, and their respective coastal waters at flight altitudes from 10,000 MSL to FL450 only, that is, it does not provide forecasts from the surface to 10,000 ft MSL.

GTG-2 graphics may be used as a higher-resolution supplement to AIRMETs and SIGMETs, but not as a substitute for the turbulence information they provide. GTG-2 graphics are authorized for use as an unrestricted, supplementary weather product. The GTG is issued by the Aviation Weather Center (AWC) and are available through the Aviation Digital Data Service (ADDS) web site at: http://adds.aviationweather.noaa.gov/turbulence/turb_nav.php.

9.5.1 Issuance The GTG-2 product consists of a 00, 01, 02, and 03 hour forecast, which are updated every hour, and a 06, 09, and 12 hour forecast, which are updated every three hours, starting at 00Z.

GTG-2 graphics are "snapshot" graphics, intended to depict forecasted clear air turbulence conditions at the valid time (for example, at 1200Z), not for a valid time range (for example, from 1200Z to 1300Z). The GTG-2 graphics suite is automatically produced with no human modifications. Information on the graphics is determined from observational data, pilot weather reports, upper air soundings, satellite soundings, automated aircraft reports, and surface weather reports, all of which are integrated with computer model output. The GTG-2 does not have the capability to be amended.

9.5.2 Content

9.5.2.1 GTG-2 Analysis and Forecast The GTG-2 00-hr (analysis) and forecast graphics depict the location and intensity of potential Clear Air Turbulence (CAT). Standard intensity terminology is used: The only turbulence intensities depicted are light and moderate or greater. Pilot reports (PIREPs) of turbulence are overlaid on the (00-hr (analysis). The GTG-2 output is available for 1,000 foot vertical intervals between 10,000 ft MSL and FL450. ADDS turbulence page displays every two thousand feet starting at 11,000 ft MSL. The ADDS Flight Path Tool allows access to GTG-2 turbulence data for different altitudes in 1000 foot increments, as well as vertical cross sections for a specific route, interactive overlays of additional weather data, and a closer look at specific geographic areas

Page 347OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Supplementary Weather Product (AIM 7-1-3): Clear-air turbulence forecast only.

See FYI/Help page for more information.

GTG2 - Turbulence forecast at FL370 Valid 1400 UTC Thu 22 Apr 2010 00-hr forecast from 1400 UTC 22 Apr ALA None Light Moderate or greater Turb PIREP Symbole g Smooth A Light A Moderate _ASavere Smooth-Light A Light-Moderate Moderate-Severe Extreme Figure 9-23. GTG Example

9.5.2.2 GTG-2 Maximum Turbulence Intensity (10000 ft. MSL to FL450) The "GTG-2 Maximum turbulence intensity (10000 ft MSL to FL45)" analysis and forecast products display the maximum intensity of potential turbulence between 10,000 ft MSL and FL450 (Figure 9-24). In other words, at any given location, the displayed value represents the maximum potential turbulence between 10,000 ft MSL and FL450. Single altitude graphics must be examined to determine the altitude of the potential turbulence.

Section 9: Supplementary Products Page 9-29

Page 348OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Supplementary Weather Product (AIM 7-1-3): Clear-air turbulence forecast only.

See FYI/Help page for more information.

GTG2 - Maximum turbulence intensity (10000 ft. MSL to FL450) Valid 1400 UTC Thu 22 Apr 2010 00-hr forecast from 1400 UTC 22 Apr ДХ None Light Moderate or greater Turb PIREP Symbols @ Smooth A Light A Moderate A Severe Smooth-Light A Light-Moderate A Moderate-Severe Extreme Figure 9-24. GTG Composite Example

9.5.3 Strengths and Limitations The GTG-2 provides an hourly, high resolution analysis (00-hr) and forecast of clear-air turbulence (CAT) potential between 10,000 ft. MSL and FL450. CAT is depicted to a higher resolution than AIRMETs and SIGMETs. However, the product is only for CAT associated with upper level fronts and jet streams and is not intended to predict turbulence associated with convection and thunderstorm clouds or breaking mountains waves. Users should also be aware that turbulence is a highly dynamic phenomenon and in case of rapidly changing conditions the product may not accurately convey a significant hazard.

9.5.4 Use The "GTG-2 Maximum turbulence intensity (10000 ft MSL to FL45)" analysis and forecast products can provide a quick method to determine what the greatest potential of clear-air Page 9-30 Section 9: Supplementary Products