AC 00-45G

Change 1Historical

Advisory circular · Aviation Weather Services

Approved
July 29, 2010
Last reviewed
September 13, 2024
This change
This entire document series, all through the H Revision, is canceled.
Cancels
AC00-45G
Cancelled by
AC00-45G CHG 2
Family
AC 00-45 · 10 versions
Revision
G, change 1
14 CFR parts
1

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 329–340
Page 341OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) The Icing Severity plus Supercooled Large Droplets (SLD) product (Figure 9-21) depicts at all altitudes, between 1,000 feet MSL and FL300, the intensity of icing expected as well as locations where a threat for SLD exists.

SLD is defined as supercooled water droplets larger than 50 micrometers in diameter. These size droplets include freezing drizzle and/or freezing rain aloft. SLD, which are outside the icing certification envelopes (FAR Part 25 Appendix C), can be particularly hazardous to some aircraft.

ly FAA policy CIP is a Supplementary Meather Product for enhanced situational awareness only and must bi sed mith one or more primary products (safety decision) such as an AIRMET or SIGMET (see AIM 7-1-3) Maximum icing severity (1000 ft. MSL to FL300) Analysis valid 1500 UTC Mon 27 Nov 2006 SLD threat None Trace Light Moderate Heavy

4) Trace-Light W Light-Maderate \ Moderate-Savare cing PIREP Symbols W Trace Yes Light y Moderate # Severe Figure 9-21. CIP Icing Severity plus Supercooled Large Droplets (SLD) - Max Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate Section 9: Supplementary Products Page 9-23

Page 342Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-24 Section 9: Supplementary Products where no probability of icing exists and, therefore, no intensity is necessary. Locations where a threat for SLD exists are depicted with red hatching.

9.3.3 Strengths and Limitations

9.3.3.1 Strengths The CIP product suite is updated hourly and provides a diagnostic tool to assist in determining the probability for icing, the intensity of icing and the threat for SLD.

9.3.3.2 Limitations Actual icing severity may be different than what is depicted on the CIP graphics and plotted PIREPS because:

Different aircraft types experience different severities of icing in the same atmospheric environments. Severity definitions are currently pilot-based and thus are a function of the aircraft type, flight phase (takeoff/landing, cruise, etc.), aircraft configuration, as well as the pilot’s experience and perception of the icing hazard.

Assessing the amount and drop size of supercooled liquid water (SLW) in the atmosphere is difficult.

The Icing Severity products depict the severity of the meteorological icing environment and not the resultant icing that may occur on the aircraft.

9.3.4 Uses The CIP Icing Probability product can be used to identify the current three-dimensional probability of icing.

The CIP Icing Severity product can be used to determine the intensity of icing. The CIP Icing Severity – Probability > 25% or Probability > 50% depicts the probability of a given intensity of icing occurring.

Finally the Icing Severity plus SLD product can help in determining the threat of SLD which is particularly hazardous to some aircraft.

Icing PIREPs are plotted on single altitude graphics if the PIREP is within 1,000 feet of the graphic’s altitude and has been observed within 75 minutes of the chart’s valid time. On CIP Max product, PIREPs for all altitudes (i.e. 1,000 feet MSL to FL300) are displayed. However, negative reports of icing are not plotted on the CIP Max product in an effort to reduce clutter.

The PIREP legend is located on the bottom of each graphic.

Page 343Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Section 9: Supplementary Products Page 9-25

9.4 Forecast Icing Potential (FIP) The Forecast Icing Potential (FIP) provides a three-dimensional forecast of icing potential (or likelihood) using numerical weather prediction model output (Figure 9-17). The FIP product suite is automatically generated with no human modifications. It may be used as a higher resolution supplement to AIRMETs and SIGMETs but is not a substitute for them. It is authorized for operational use only by meteorologists and dispatchers. The forecast area covers the 48-contiguous states, much of Canada and Mexico and their respective coastal waters.

9.4.1 Issuance The FIP is issued every hour and generates hourly forecast for 3 hours into the future. For example, forecasts issued at 1300Z would be valid for 1400Z, 1500Z and 1600Z. Six-, 9-, and 12-hour forecasts are issued every three hours beginning at 00Z. For example, a forecast suite issued at 0300Z would have valid times at 0900Z, 1200Z and 1500Z respectively. The product is issued by the Aviation Weather Center (AWC) and is available through the Aviation Digital Data Service (ADDS) web site at: http://adds.aviationweather.noaa.gov/icing/icing_nav.php.

9.4.2 Content The FIP forecasts the likelihood of icing from super-cooled liquid water droplets. The likelihood field ranges from 0 (no icing) to 100 (icing likely). The scale depicts likelihood of icing using “cool” and “warm” colors, with warmer colors indicating a higher likelihood of icing. Regions depicted in white indicate zero icing potential according to the CIP. Brown regions indicate areas of terrain.

The scale is not calibrated as a true probability value. It does, however, have value in pointing out differences in the likelihood of encountering icing at a given location. For example, a value of 70 does not indicate there is a 70 percent chance of encountering icing. However, when comparing it to other higher or lower values will indicate if there is a greater or lesser likelihood of encountering icing. No information is provided as to the severity of icing and none should be inferred. FIP output is available for 1,000 foot vertical intervals. ADDS displays every third level except on the Flight Path Tool which provides access to all levels.

Page 344Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-26 Section 9: Supplementary Products

Figure 9-22. FIP Example

9.4.3 Strengths and Limitations

Strengths

 The FIP can be used to help determine the forecast for potential for icing through the entire vertical depth of the atmosphere.

 The product is updated hourly.

Limitations

 The product does not display any information about the severity of icing.

 The product only displays the forecast potential for icing, not the absolute probability.

 It is only approved for use by meteorologists and dispatchers.

Page 345Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Section 9: Supplementary Products Page 9-27

 The product is generated without human modification. Therefore, the forecasts are only as accurate the computer model output used to create them.

9.4.4 Use The FIP is primarily used to help determine the likelihood of icing at the specified forecast valid times.

Page 346Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-28 Section 9: Supplementary Products

9.5 Graphical Turbulence Guidance (GTG-2) The Graphical Turbulence Guidance (GTG-2) graphics are computer-generated fourdimensional forecasts of information related to the likelihood of encountering Clear Air Turbulence (CAT) associated with upper-level fronts and jet streams. It is not intended to predict turbulence associated with convection and thunderstorm clouds or breaking mountain waves.

The product provides forecasts for the 48 contiguous United States, much of Canada and Mexico, and their respective coastal waters at flight altitudes from 10,000 MSL to FL450 only, that is, it does not provide forecasts from the surface to 10,000 ft MSL.

GTG-2 graphics may be used as a higher-resolution supplement to AIRMETs and SIGMETs, but not as a substitute for the turbulence information they provide. GTG-2 graphics are authorized for use as an unrestricted, supplementary weather product. The GTG is issued by the Aviation Weather Center (AWC) and are available through the Aviation Digital Data Service (ADDS) web site at: http://adds.aviationweather.noaa.gov/turbulence/turb_nav.php.

9.5.1 Issuance The GTG-2 product consists of a 00, 01, 02, and 03 hour forecast, which are updated every hour, and a 06, 09, and 12 hour forecast, which are updated every three hours, starting at 00Z.

GTG-2 graphics are "snapshot" graphics, intended to depict forecasted clear air turbulence conditions at the valid time (for example, at 1200Z), not for a valid time range (for example, from 1200Z to 1300Z). The GTG-2 graphics suite is automatically produced with no human modifications. Information on the graphics is determined from observational data, pilot weather reports, upper air soundings, satellite soundings, automated aircraft reports, and surface weather reports, all of which are integrated with computer model output. The GTG-2 does not have the capability to be amended.

9.5.2 Content

9.5.2.1 GTG-2 Analysis and Forecast The GTG-2 00-hr (analysis) and forecast graphics depict the location and intensity of potential Clear Air Turbulence (CAT). Standard intensity terminology is used: The only turbulence intensities depicted are light and moderate or greater. Pilot reports (PIREPs) of turbulence are overlaid on the (00-hr (analysis). The GTG-2 output is available for 1,000 foot vertical intervals between 10,000 ft MSL and FL450. ADDS turbulence page displays every two thousand feet starting at 11,000 ft MSL. The ADDS Flight Path Tool allows access to GTG-2 turbulence data for different altitudes in 1000 foot increments, as well as vertical cross sections for a specific route, interactive overlays of additional weather data, and a closer look at specific geographic areas

Page 347OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Supplementary Weather Product (AIM 7-1-3): Clear-air turbulence forecast only.

See FYI/Help page for more information.

GTG2 - Turbulence forecast at FL370 Valid 1400 UTC Thu 22 Apr 2010 00-hr forecast from 1400 UTC 22 Apr ALA None Light Moderate or greater Turb PIREP Symbole g Smooth A Light A Moderate _ASavere Smooth-Light A Light-Moderate Moderate-Severe Extreme Figure 9-23. GTG Example

9.5.2.2 GTG-2 Maximum Turbulence Intensity (10000 ft. MSL to FL450) The "GTG-2 Maximum turbulence intensity (10000 ft MSL to FL45)" analysis and forecast products display the maximum intensity of potential turbulence between 10,000 ft MSL and FL450 (Figure 9-24). In other words, at any given location, the displayed value represents the maximum potential turbulence between 10,000 ft MSL and FL450. Single altitude graphics must be examined to determine the altitude of the potential turbulence.

Section 9: Supplementary Products Page 9-29

Page 348OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Supplementary Weather Product (AIM 7-1-3): Clear-air turbulence forecast only.

See FYI/Help page for more information.

GTG2 - Maximum turbulence intensity (10000 ft. MSL to FL450) Valid 1400 UTC Thu 22 Apr 2010 00-hr forecast from 1400 UTC 22 Apr ДХ None Light Moderate or greater Turb PIREP Symbols @ Smooth A Light A Moderate A Severe Smooth-Light A Light-Moderate A Moderate-Severe Extreme Figure 9-24. GTG Composite Example

9.5.3 Strengths and Limitations The GTG-2 provides an hourly, high resolution analysis (00-hr) and forecast of clear-air turbulence (CAT) potential between 10,000 ft. MSL and FL450. CAT is depicted to a higher resolution than AIRMETs and SIGMETs. However, the product is only for CAT associated with upper level fronts and jet streams and is not intended to predict turbulence associated with convection and thunderstorm clouds or breaking mountains waves. Users should also be aware that turbulence is a highly dynamic phenomenon and in case of rapidly changing conditions the product may not accurately convey a significant hazard.

9.5.4 Use The "GTG-2 Maximum turbulence intensity (10000 ft MSL to FL45)" analysis and forecast products can provide a quick method to determine what the greatest potential of clear-air Page 9-30 Section 9: Supplementary Products

Page 349Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Section 9: Supplementary Products Page 9-31 turbulence (CAT) is at a given location. However, to determine the CAT potential at any given altitude, the individual altitude products must be viewed.

Page 350Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-32 Section 9: Supplementary Products

9.6 Meteorological Impact Statement (MIS) A Meteorological Impact Statement (MIS) is an unscheduled flow control and flight operations planning forecast issued by Center Weather Service Units (CWSUs) (Figures 9-21 and 9-22). It is a forecast and briefing product for personnel at Air Route Traffic Control Centers (ARTCCs), Air Traffic Control System Command Center (ATCSCC), Terminal Radar Approach Control Facilities (TRACONS) and Airport Traffic Control Towers (ATCTs) responsible for making flow control-type decisions.

A MIS may be tailored to meet the unique requirements of the host ARTCC. These special requirements will be coordinated between the host ARTCC and the CWSU.

MISs are available on the Aviation Weather Center (AWC) web site at:

http://aviationweather.gov/products/cwsu/.

9.6.1 Valid Period A MIS is valid up to 12 hours after issuance time and details weather conditions expected to adversely impact air traffic flow in the CWSU area of responsibility. The MIS can be immediately effective for existing conditions when CWSU operations begin or for rapidly deteriorating conditions or be effective up to two hours in advance of expected conditions.

9.6.2 MIS Criteria A MIS enables Air Traffic Control (ATC) facility personnel to include the impact of specific weather conditions in their flow control decision-making. At a minimum, a MIS should be issued when:

Any of the following conditions occur, are forecast to occur, and, if previously forecast, are no longer expected:

o Conditions meeting convective SIGMET criteria (Section 5.1.8)

o Icing - moderate or greater

o Turbulence - moderate or greater

o Heavy precipitation

o Freezing precipitation

o Conditions at or approaching Low IFR

o Surface winds/gusts >30 knots

o Low Level Wind Shear (surface - 2,000 feet)

o Volcanic ash, dust storms, or sandstorms; and

In the forecaster's judgment, the conditions listed above, or any others, will adversely impact the flow of air traffic within the ARTCC area of responsibility.

Page 351Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Section 9: Supplementary Products Page 9-33

9.6.3 MIS Issuance MIS phenomena forecasts use the location reference point identifiers depicted on the In-Flight Advisory Plotting Chart (Appendix F), and include the height, extent, and movement of the conditions. MIS product issuances are numbered sequentially beginning at Midnight local time each day. The MIS is disseminated and stored as a "replaceable" product. Therefore, each issuance will contain the details of all pertinent known conditions meeting MIS issuance criteria, including ongoing conditions described in previously issued MISs.

The MIS is for internal use by ARTCC personnel, including Traffic Management Unit (TMU) and TRACON as needed. The MIS is not intended for use by pilots or dispatchers.

9.6.4 Format

Figure 9-25. Meteorological Impact Statement (MIS) Decoding Example

Table 9-5. Meteorological Impact Statement (MIS) – Decoding

LINE CONTENT DESCRIPTION 1 ZFW ARTCC Identification MIS Product type 01 Issuance number VALID 190200-191200 Valid period UTC date/time 2 …FOR ATC PLANNING PURPOSES ONLY… Product use statement 3 FROM OKC TO CDS TO GAG TO END TO OKC Phenomenon location 4 LLWS BLO 020 AGL DUE TO LLJ.

CONDS GRDLY IPVG AFT 10Z Phenomenon description

Any remarks such as “SEE CONVECTIVE SIGMET 8W"; "NO UPDATES AVBL AFT 0230Z";

and forecaster initials and/or facility identifier may be placed at the end of the MIS.

If the phenomenon described in a MIS is no longer expected, a cancellation MIS message may be issued. The FAA header does not contain an issuance number. If the phenomenon described in the MIS is expected to continue beyond the operating hours of the CWSU, then the remark "NO UPDATES AFT ttttZ" (where "ttttZ" is the UTC closing time of the CWSU) is added at the text end.

Page 352Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 1 (July 2010) Page 9-34 Section 9: Supplementary Products

9.6.5 Examples

ZOA MIS 01 VALID 041415-041900 ...FOR ATC PLANNING PURPOSES ONLY...

FOR SFO BAY AREA BR/FG WITH CEILING BLW 005 AND VIS OCNL BLW 1SM.

ZOA CWSU

Meteorological Impact Statement issued by the Freemont, California CWSU. First MIS issuance of the day, valid from the 4th day of the month at 1415 UTC, to the 4th day of the month at 1900 UTC. For air traffic control planning purposes only. For the San Francisco Bay Area…mist and fog with ceilings below 500 feet MSL and visibility occasionally below 1 statute mile.

ZOA MIS 02 VALID 041650 ...FOR ATC PLANNING PURPOSES ONLY...

FOR SFO BAY AREA CNL ZOA MIS 01. CONDS HAVE IMPRD.

ZOA CWSU

Meteorological Impact Statement issued by the Freemont, California CWSU. The second MIS issuance of the day, valid the 4th day of the month at 1650 UTC. For air traffic control planning purposes only. For the San Francisco Bay Area. Cancel Freemont, California Meteorological Impact Statement number 1. Conditions have improved.

ZID MIS 03 VALID 041200-042330 ...FOR ATC PLANNING PURPOSES ONLY...

FROM IND TO 17WSW APE TO LOZ TO 13NE PXV TO IND TIL 21Z MOD TURB FL310-390 DUE TO JTST WS.

ZID W OF A LINE FM FWA TO BWG AFT 18Z OCNL SEV TSGR TOPS TO FL450. MOV FM 24035KT. MAX SFC WINDS 60KT.

ZID E OF A LINE FM FWA TO 35SE BKW MOD MXD ICE IN CLDS/PRECIPITATION 020-120. CONDS ENDING W OF A 40S CLE TO 20NE BKW LINE BY 19Z.

ZID CWSU

Meteorological Impact Statement issued by the Indianapolis, Indiana CWSU. The third MIS issuance of the day, valid from the 4th day of the month at 1200 UTC to the 4th day of the month at 2130 UTC. For air traffic control planning purposes only. From Indianapolis, Indiana to 17 nautical miles west-southwest of Appleton, Ohio to London, Kentucky to 13 nautical miles northeast of Pocket City, Indiana to Indianapolis, Indiana. Until 21Z, moderate turbulence between flight level 310 and flight level 390 due to jet stream wind shear.

For the Indianapolis ARTCC airspace west of a line from Fort Wayne, Indiana to Bowling Green, Kentucky. After 18Z, occasional severe thunderstorms, hail, tops to flight level 450. Moving from 240 degrees at 35 knots. Maximum surface winds 60 knots.

For the Indianapolis, Indiana ARTCC airspace east of a line from Fort Wayne, Indiana to 35 nautical miles southeast of Beckley, West Virginia. Moderate mixed icing in clouds and precipitation between 2,000 feet to 12,000 feet MSL. Conditions ending west of a line from 40