AC 00-45G

Change 2Historical

Advisory circular · Aviation Weather Services

Approved
October 1, 2014
Last reviewed
September 13, 2024
This change
CHG 2 of AC 00-45G. This entire document series, all through the H Revision, is canceled.
Cancelled by
AC00-45H
Family
AC 00-45 · 10 versions
Revision
G, change 2
14 CFR parts
1

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 21–32

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

• Introduction. Includes the preparation time and the route and/or the area of coverage. The service area may be configured to meet the individual facility’s needs.

• Adverse Conditions. A summary of Convective SIGMETs, SIGMETs, AIRMETs, Center Weather Advisories, Alert Severe Weather Watch Bulletins, and any other available information that may adversely affect flight in the route/area.

• VNR Statement. Included when current or forecast conditions, surface or aloft, would make the flight under VFR doubtful.

• Synopsis. A brief statement describing the type, location, and movement of weather systems and/or air masses that might affect the route or the area. This element may be combined with adverse conditions and/or the VNR element, in any order, when it will help to more clearly describe conditions.

• Current Conditions. A summary of current weather conditions over the route/area.

PIREPs are included on conditions reported aloft and a summary of observed radar echoes. Specific departure/destination observation may also be included.

• Density Altitude. The statement “check density altitude” will be included for any weather reporting point with a field elevation of 2,000 feet mean sea level (MSL) or above that meets certain temperature criteria.

• En Route Forecast. A summary of appropriate forecast data provided in logical order,

i.e., climb out, en route, and descent.

• Winds Aloft. A summary of winds aloft forecast for the route/area as interpolated from forecast data for the local and/or the adjacent reporting locations for levels through 12,000 feet. The broadcast should include the levels from 3,000 to 12,000 feet, but usually includes at least 2 forecast levels above the surface.

• Request for PIREPs. When weather conditions within the area or along the route meet requirements for soliciting PIREPs, a request will be included in the recording.

• NOTAM information that affects the route/area may be included as part of the briefing, on a separate channel, or obtained by direct contact with a pilot weather briefer.

• Military Training Activity. A statement is included in the closing announcement to contact a briefer for information on military training activity.

• Closing Announcement.

TIBS services may be reduced during the hours of 1800–0600 local time only. Resumption of full broadcast service is adjusted seasonally to coincide with daylight hours. During the period of reduced broadcast, a recorded statement may indicate when the broadcast will be resumed and to contact Flight Service for weather briefing and other services.

For those pilots already in flight and needing weather information and assistance, the following services are provided by FSSs. They can be accessed over the proper radio frequencies printed in flight information publications.

Section 1: Aviation Weather Service Program Page 1-9

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

1.3.5 Hazardous Inflight Weather Advisory Service (HIWAS) HIWAS is a national program for broadcasting hazardous weather information continuously over selected navigational aids (NAVAIDs). The broadcasts include advisories such as AIRMETs, SIGMETS, Convective SIGMETs, and urgent PIREPs. These broadcasts are only a summary of the information, and pilots should contact an FSS or EFAS for detailed information.

The HIWAS broadcast area is defined as the area within 150 NM of HIWAS outlets.

HIWAS broadcasts are not interrupted or delayed except for emergency situations, when an aircraft requires immediate attention, or for reasonable use of the voice override capability on specific HIWAS outlets in order to use the limited Remote Communications Outlet (RCO) to maintain en route communications. The service is provided 24 hours a day. An announcement is made for no hazardous weather advisories.

Hazardous weather information is recorded if it is occurring within the HIWAS broadcast area.

The broadcast includes the following elements:

• A statement of introduction including the appropriate area(s) and a recording time.

• A summary of Convective SIGMETs, SIGMETs, AIRMETs, Urgent PIREPs, Aviation Watch Notification Messages, Center Weather Advisories, and any other weather such as isolated thunderstorms that are rapidly developing and increasing in intensity, or low ceilings and visibilities that are becoming widespread which are considered significant and are not included in a current hazardous weather advisory.

• A request for PIREPs, if applicable.

• A recommendation to contact FSS/FLIGHT WATCH for additional details concerning hazardous weather.

Once the HIWAS broadcast is updated, an announcement will be made once on all communications/NAVAID frequencies except emergency, EFAS, and navigational frequencies already dedicated to continuous broadcast services. In the event a HIWAS broadcast area is out of service, an announcement is made on all communications/NAVAID frequencies except on emergency, EFAS, and navigational frequencies already dedicated to continuous broadcast services.

1.3.6 En Route Flight Advisory Service (EFAS) The purpose of EFAS, radio call “FLIGHT WATCH” (FW), is to provide en route aircraft with timely and pertinent weather data tailored to a specific altitude and route using the most current available sources of aviation meteorological information.

EFAS specialists tailor en route flight advisories to the phase of flight that begins after climb out and ends with descent to land. Current weather and terminal forecast at the airport of first intended landing and/or the alternate airport is provided on request. When conditions dictate, EFAS specialists provide information on weather for alternate routes and/or altitudes to assist the pilot in the avoidance of hazardous flight conditions. The pilot is advised to contact the adjacent flight watch facility when adverse weather conditions along the intended route extend beyond the Flight Watch Area (FWA).

Section 1: Aviation Weather Service Program Page 1-10

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) EFAS is not used for routine in-flight services; e.g., flight plan filing, position reporting, or full route (pre-flight) briefings. If a request for information is received that is not within the scope of EFAS, the pilot is advised of the appropriate FSS to contact.

EFAS specialists suggest route or destination changes to avoid areas of weather that in the judgment of the specialists constitutes a threat to safe flight.

EFAS is provided on 122.0 MHz to aircraft below FL180. An assigned discrete frequency is used to provide EFAS to aircraft at FL180 and above. This frequency can also be used for communications with aircraft below FL180 when communication coverage permits. Aircraft operating at FL180 or above that contact FW on frequency 122.0 MHz are advised to change to the discrete frequency for EFAS.

1.3.7 Automatic Dependent Surveillance – Broadcast (ADS-B) ADS-B is a surveillance system combining the advanced technologies of satellite positioning, aircraft avionics, and ground-based transceivers. ADS-B equipped aircraft automatically broadcast their identification, current position, altitude, and velocity information approximately once per second. This continuous broadcast of flight data improves aircraft position accuracy beyond the capabilities of current NAS radar/transponder-based surveillance systems.

In the United States, two different data links have been adopted for use with ADS-B: 1090 MHz Extended Squitter (1090ES) and the 978 MHz, Universal Access Transceiver (UAT). The 1090ES link is intended for aircraft that primarily operate at FL240 and above, whereas the UAT link is intended for use by aircraft that primarily operate at lower altitudes. From a pilot’s standpoint, the two links operate similarly and support ADS-B and Traffic Information Services-Broadcast (TIS-B). The UAT link will provide additional weather and other aeronautical information through the Flight Information Service - Broadcast (FIS-B).

1.3.7.1 Flight Information Service – Broadcast (FIS-B) FIS-B is a ground-based broadcast service provided through the FAA’s ADS-B Services UAT network. The service provides users with a 978 MHz data link capability when operating within range and line-of-sight of a transmitting ground station. FIS-B enables users of properly equipped aircraft to receive and display a suite of broadcast weather and aeronautical information products.

The following list represents the initial suite of textual and graphical products available through FIS-B and provided free-of-charge. This advisory circular (AC) and the current edition of AC 00-63, Use of Cockpit Displays of Digital Weather and Aeronautical Information, contain detailed information concerning FIS-B meteorological products. Chapters 3, 4 and 5 of the AIM contain information on Special Use Airspace (SUA), TFR, and NOTAM products.

• Text: METAR and Aviation Selected Special Weather Report (SPECI);

• Text: PIREP;

• Text: Winds and Temperatures Aloft;

• Text: Terminal Aerodrome Forecast (TAF) and amendments;

• Text: NOTAM Distant and Flight Data Center;

Section 1: Aviation Weather Service Program Page 1-11

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

• Text/Graphic: AIRMET;

• Text/Graphic: SIGMET;

• Text/Graphic: Convective SIGMET;

• Text/Graphic: Special Use Airspace

• Text/Graphic: TFR NOTAM; and

• Graphic: Next generation weather radar (NEXRAD) Composite Reflectivity Products (Regional and National).

Users of FIS-B should familiarize themselves with the operational characteristics and limitations of the system, including: system architecture; service environment; product lifecycles; modes of operation; and indications of system failure.

Update intervals are defined as the rate at which the product data is available from the source for transmission. Transmission intervals are defined as the amount of time within which a new or updated product transmission must be completed and/or the rate or repetition interval at which the product is rebroadcast. Table 1-1 provides update and transmission intervals for each product.

Where applicable, FIS-B products include a look-ahead range expressed in nautical miles (NM) for three service domains: Airport Surface; Terminal Airspace; and En-route/Gulf-of-Mexico (GOMEX). Table 1-1 provides service domain availability and look-ahead ranging for each FIS-B product.

Prior to using this capability, users should familiarize themselves with the operation of FIS-B avionics by referencing the applicable User’s Guides. Users should obtain guidance concerning the interpretation of information displayed from the appropriate avionics manufacturer.

Users should report FIS-B malfunctions not attributed to aircraft system failures or covered by active NOTAM to the nearest FSS facility by radio or telephone. Users may also report malfunctions by submitting FAA Form 8740-5, Safety Improvement Report, via mail, fax, or email to your local Flight District Standards Office (FSDO) Safety Program Manager.

Section 1: Aviation Weather Service Program Page 1-12

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) Table 1-1. FIS-B Over UAT Product Update and Transmission Intervals Product FIS-B Over UAT Service Update Intervals1 FIS-B Service Transmission Intervals2 AIRMET As available 5 minutes Convective SIGMET As available 5 minutes METARs / SPECIs 1 minute / as available 5 minutes NEXRAD Composite Reflectivity (CONUS) 15 minutes 15 minutes NEXRAD Composite Reflectivity (Regional) 5 minutes 2.5 minutes NOTAMs-D/FDC/TFR As available 10 minutes PIREP As available 10 minutes SIGMET As available 5 minutes Special Use Airspace Status As available 10 minutes TAF/AMEND 8 hours/as available 10 minutes Temperature Aloft 12 hours 10 minutes Winds Aloft 12 hours 10 minutes 1 The Update Interval is the rate at which the product data is available from the source.

2 The Transmission Interval is the amount of time within which a new or updated product transmission must be completed and the rate or repetition interval at which the product is rebroadcast.

Section 1: Aviation Weather Service Program Page 1-13

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) Table 1-2. Product Parameters for Low/Medium/High Altitude Tier Radios Product Surface Radios Low Altitude Tier Medium Altitude Tier High Altitude Tier

CONUS NEXRAD N/A CONUS NEXRAD not provided CONUS NEXRAD imagery CONUS NEXRAD imagery Winds & Temps Aloft 500 NM look-ahead range 500 NM look-ahead range 750 NM look-ahead range 1,000 NM look-ahead range METAR 100 NM look-ahead range 250 NM look-ahead range 375 NM look-ahead range CONUS: CONUS Class B & C airport METARs and 500 NM look-ahead range Outside of CONUS: 500 NM look-ahead range TAF 100 NM look-ahead range 250 NM look-ahead range 375 NM look-ahead range CONUS: CONUS Class B & C airport TAFs and 500 NM look-ahead range Outside of CONUS: 500 NM look-ahead range

AIRMET, SIGMET, PIREP, and Special Use Airspace / SAA 100 NM look-ahead range.

PIREP/SUA is N/A 250 NM look-ahead Range 375 NM look-ahead range 500 NM look-ahead range Regional NEXRAD 150 NM look-ahead range 150 NM look-ahead range 200 NM look-ahead range 250 NM look-ahead range NOTAMs D, FDC, TFR 100 NM look-ahead range 100 NM look-ahead range 100 NM look-ahead range 100 NM look-ahead range Users should obtain guidance concerning the content, format, and symbology of individual FIS-B products from the manufacturer of the avionics equipment used to receive and display them.

Section 1: Aviation Weather Service Program Page 1-14

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

1.3.7.2 Operational Use of FIS-B Products FIS-B products are intended to enhance the user’s situational awareness and enable more efficient use of ATC/FSS/AOCC services. The information provided by FIS-B is advisory in nature and should not be used in lieu of individual pre-flight, in-flight, weather, or flight planning briefings provided by ATC/FSS/AOCC services.

Section 1: Aviation Weather Service Program Page 1-15

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) 2 AVIATION WEATHER PRODUCT POLICY The demand for new and improved aviation weather products continues to grow and, with new products introduced to meet the demand, some confusion has resulted in the aviation community regarding the relationship between regulatory requirements and the new weather products.

This section will clarify that relationship by providing:

• P olicy guidance for using aviation weather products,

• D escriptions of the types of aviation weather information, and

• Ca tegorization of the sources of aviation weather information.

2.1 Use of Aviation Weather Products With increased access to these weather products via the public Internet, the aviation community has access to an overwhelming amount of weather information and data that support self-briefing. This advisory circular (AC) describes the weather products distributed by the National Weather Service (NWS). Pilots and operators using the public Internet to access weather from a third-party vendor should request and/or review an appropriate description of services and provider disclosure. This should include, but is not limited to, the type of weather product (e.g., current weather or forecast weather), the currency of the product (i.e., product issue and valid times), and the relevance of the product. Pilots and operators should be cautious when using unfamiliar weather products and when in doubt, consult with a Flight Service Specialist.

The development of new weather products, coupled with the termination of some legacy textual and graphical products may create confusion between regulatory requirements and the new products. All flight-related aviation weather decisions must be based on all available pertinent weather products. As every flight is unique and the weather conditions for that flight vary hour by hour, day to day, multiple weather products may be necessary to meet aviation weather regulatory requirements. Many new weather products now have a Precautionary Use Statement that details the proper use or application of the specific product.

Section 2: Aviation Weather Product Policy Page 2-1

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

2.2 Types of Aviation Weather Information The Federal Aviation Administration (FAA) has identified the following three distinct types of weather information that may be needed to conduct aircraft operations: observations, analyses, and forecasts.

2.2.1 Observations Observations are raw weather data collected by some type of sensor(s). The observations can either be in situ (e.g., surface or airborne) or remote (e.g., weather radar, satellite, profiler, and lightning).

2.2.2 Analysis Analyses of weather information are an enhanced depiction and/or interpretation of observed weather data.

2.2.3 Forecasts Forecasts are the predictions of the development and/or movement of weather phenomena based on meteorological observations and various mathematical models.

In-flight weather advisories, including Significant Meteorological Information (SIGMET), Convective SIGMETs, Airman’s Meteorological Information (AIRMET), Center Weather Advisories (CWA), and Meteorological Impact Statements (MIS), are considered forecast weather information products.

Section 2: Aviation Weather Product Policy Page 2-2

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

2.3 Categorizing Aviation Weather Sources The regulations pertaining to aviation weather reflect that, historically, the Federal Government was the only source of aviation weather information. That is, the FAA and NWS, or its predecessor organizations, were solely responsible for the collection and dissemination of weather data, including forecasts. Thus, the term “approved source(s)” referred exclusively to the Federal Government. The Federal Government is no longer the only source of weather information, due to the growing sophistication of aviation operations and scientific and technological advances.

Since all three types of weather information defined in paragraph 2.2 are not available from all sources of aviation weather information, the FAA has categorized the sources as follows: Federal Government, Enhanced Weather Information System (EWINS), and commercial weather information providers.

2.3.1 Federal Government The FAA and NWS collect weather observations. The NWS analyzes the observations, and produces forecasts, including in-flight aviation weather advisories (e.g., SIGMETs). The FAA and NWS disseminate meteorological observations, analyses, and forecast products through a variety of systems. The Federal Government is the only approval authority for sources of weather observations (e.g., contract towers and airport operators).

Commercial weather information providers contracted by the FAA to provide weather observations

(e.g., contract towers, Lockheed Martin, Direct Use Access Terminal Service (DUAT/DUATS) are included in the Federal Government category of approved sources by virtue of maintaining required technical and quality assurance standards under FAA and NWS oversight.

2.3.2 Enhanced Weather Information System (EWINS) An EWINS is a system for gathering, evaluating, and disseminating aviation weather information, and for issuing weather reports and forecasts prepared by properly trained and qualified aviation meteorologists or aircraft dispatchers. Air carriers use EWINS, which are proprietary to each carrier.

In order to use an EWINS, each air carrier requires FAA approval.

To receive FAA approval, each carrier’s EWINS must have sufficient procedures, personnel, and communications and data processing equipment to effectively obtain, analyze, and disseminate aeronautical weather data. For a full explanation of the requirements for EWINS approval, see the Flight Standards Information Management System (FSIMS), Order 8900.1, Volume 3, Chapter 26, Section 4, Enhanced Weather Information Systems. An EWINS source may produce weather analyses and forecasts based on meteorological observations provided by the Federal Government. Approval to use EWINS weather products is issued on a case-by-case basis and is currently only applicable to Title 14 of the Code of Federal Regulations (14 CFR) part 91K Program Managers and 14 CFR part 121/135 certificate holders, who may either act as their own EWINS or contract those services from a separate entity. These approved operators may conduct flight operations using the weather analyses and forecasts produced by their approved EWINS.

Section 2: Aviation Weather Product Policy Page 2-3

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

2.3.3 Commercial Weather Information Providers Commercial weather providers are a major source of weather products for the aviation community.

In general, they produce proprietary weather products based on NWS products with formatting and layout modifications but no material changes to the weather information itself. This is also referred to as “repackaging.”

Commercial providers may also produce forecasts, analyses, and other proprietary weather products and substantially alter the information contained in NWS-produced products. Operators who desire to use products prepared by a commercial weather provider as opposed to using products that are simply repackaged, may require FAA approval to use an EWINS. For more information on whether an EWINS is required to use products prepared by a commercial weather provider, refer to FSIMS, Order 8900.1, Volume 3, Chapter 26, Section 2, Regulatory Sources of Aviation Weather Information. Operators and pilots contemplating using such services should request and/or review an appropriate description of services and provider disclosure. This should include, but is not limited to:

• The type of weather product (e.g., current weather or forecast weather),

• The currency of the product (i.e., product issue and valid times), and

• The relevance of the product.

Pilots and operators should be cautious when using unfamiliar products, or products not supported by FAA/NWS technical specifications.

Section 2: Aviation Weather Product Policy Page 2-4

Aviation Weather Services, Advisory Circular 00-45G Change 1 (July 2010) 3 OBSERVED TEXT PRODUCTS

3.1 Aviation Routine Weather Reports (METAR) and Aviation Selected Special Weather Reports (SPECI) Surface weather observations are fundamental to all meteorological services. Observations are the basic information upon which forecasts and warnings are made in support of a wide range of weather sensitive activities within the public and private sectors, including aviation.

Although the METAR/SPECI code is used worldwide, each country is allowed to make modifications or exceptions to the code for use in their particular country. This section will focus on the U.S. modifications and exceptions. METAR/SPECIs are available online at:

http://adds.aviationweather.gov/metars/

3.1.1 Aviation Routine Weather Report (METAR) Aviation Routine Weather Report (METAR) is the primary observation code used in the U. S. to satisfy World Meteorological Organization (WMO) and International Civil Aviation Organization (ICAO) requirements for reporting surface meteorological data. A METAR report includes the airport identifier, time of observation, wind, visibility, runway visual range, present weather phenomena, sky conditions, temperature, dew point, and altimeter setting. Excluding the airport identifier and the time of observation, this information is collectively referred to as “the body of the report.” As an addition, coded and/or plain language information elaborating on data in “the body of the report” may be appended to the end of the METAR in a section coded as “Remarks.” The contents of the “Remarks” section vary with the type of reporting station. The METAR may be abridged at some designated stations only including a few of the mentioned elements.

3.1.2 Aviation Selected Special Weather Report (SPECI) An Aviation Selected Special Weather Report (SPECI) is an unscheduled report taken when any of the criteria given in Table 3-1 are observed during the interim period between the hourly reports. SPECI contains all data elements found in a METAR plus additional plain language information which elaborates on data in the body of the report. All SPECIs are made as soon as possible after the relevant criteria are observed.

Whenever SPECI criteria are met at the time of the routine METAR, a METAR is issued.

Section 3: Observed Text Products Page 3-1