AC 00-45G

Change 2Historical

Advisory circular · Aviation Weather Services

Approved
October 1, 2014
Last reviewed
September 13, 2024
This change
CHG 2 of AC 00-45G. This entire document series, all through the H Revision, is canceled.
Cancelled by
AC00-45H
Family
AC 00-45 · 10 versions
Revision
G, change 2
14 CFR parts
1

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 333–344
Page 345Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

Figure 9-17. CIP/FIP Icing Severity Probability >25 Percent Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. A gray color is used to mask the intensity pixels where the probability of icing is 25 percent or less.

Icing Severity – Probability > 50 Percent The Icing Severity – Probability > 50 percent product (Figure 9-18) depicts, at a single altitude, where the probability of the indicated icing intensity 51 to 100 percent. Icing intensity is displayed using icing intensity categories: trace, light, moderate, and heavy.

Section 9: New Generation Weather Products Page 9-20

Page 346Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

Figure 9-18. CIP/FIP Icing Severity Probability > 50 Percent Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. Brown regions indicate where higher-elevation terrain extends above the altitude of the particular graphic. A gray color is used to mask the intensity pixels where the probability of icing is 50 percent or less.

Icing Severity – Probability > 50 Percent – Maximum The Icing Severity – Probability > 50 percent - Maximum product (Figure 9-19) depicts, at all altitudes from 1,000 feet MSL to FL300, where the probability of the indicated icing intensity is 51 to 100 percent. Icing intensity is displayed using icing intensity categories: trace, light, moderate, and heavy.

Section 9: New Generation Weather Products Page 9-21

Page 347Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

Figure 9-19. CIP/FIP Icing Severity Probability > 50 Percent – Max Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. A gray color is used to mask the intensity pixels where the probability of icing is 50 percent or less.

Icing Severity Plus Supercooled Large Drops (SLD) The Icing Severity plus Supercooled Large Drops (SLD) product (Figure 9-20) depicts, at a single altitude, the intensity of icing expected as well as locations where a threat for SLD exists.

SLD is defined as supercooled water droplets larger than 50 micrometers in diameter. These size droplets include freezing drizzle and/or freezing rain aloft. SLD, which are outside the icing certification envelopes (14 CFR part 25 Appendix C), can be particularly hazardous to some aircraft.

Icing intensity is displayed using icing intensity categories: trace, light, moderate, and heavy.

Section 9: New Generation Weather Products Page 9-22

Page 348Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

Figure 9-20. CIP/FIP Icing Severity Plus Supercooled Large Drops (SLD) Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. Brown regions indicate where higher-elevation terrain extends above the altitude of the particular graphic. Locations where a threat for SLD exists are depicted with red hatching.

Icing Severity Plus Supercooled Large Drops (SLD) – Maximum The SLD-Maximum product (Figure 9-21) depicts at all altitudes, between 1,000 feet MSL and FL300, the intensity of icing expected as well as locations where a threat for SLD exists.

SLD is defined as supercooled water drops larger than 50 micrometers in diameter. These size drops include freezing drizzle and/or freezing rain aloft. SLD, which are outside the icing Section 9: New Generation Weather Products Page 9-23

Page 349Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) certification envelopes (14 CFR part 25 Appendix C), can be particularly hazardous to some aircraft.

Figure 9-21. CIP/FIP Icing Severity Plus Supercooled Large Droplets (SLD) – Max Example The lightest blue color represents trace icing. As the blue color shades become darker, the icing intensity increases. The darkest blue color represents heavy icing. White regions indicate where no probability of icing exists and, therefore, no intensity is necessary. Locations where a threat for SLD exists are depicted with red hatching.

Section 9: New Generation Weather Products Page 9-24

Page 350Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) Strengths and Limitations Strengths The CIP product suite is updated hourly and provides a diagnostic tool to assist in determining the probability for icing, the intensity of icing, and the threat for SLD.

Limitations Actual icing severity may be different than what is depicted on the CIP graphics and plotted PIREPS because:

• Different aircraft types experience different severities of icing in the same atmospheric environments. Severity definitions are currently pilot-based and thus are a function of the aircraft type, flight phase (takeoff/landing, cruise, etc.), aircraft configuration, as well as the pilot’s experience and perception of the icing hazard.

• Assessing the amount and drop size of supercooled liquid water (SLW) in the atmosphere is difficult.

• The Icing Severity products depict the severity of the meteorological icing environment and not the resultant icing that may occur on the aircraft.

Uses The CIP/FIP Icing Probability product can be used to identify the current and forecast three-dimensional probability of icing. The CIP/FIP should be used in conjunction with the report and forecast information contained in an AIRMET and SIGMET.

The CIP/FIP Icing Severity product can be used to determine the intensity of icing. The CIP/FIP Icing Severity – Probability > 25 percent or Probability > 50 percent depicts the probability of a given intensity of icing occurring.

Finally, the Icing Severity plus SLD product can help in determining the threat of SLD, which is particularly hazardous to some aircraft.

Icing PIREPs are plotted on single altitude graphics if the PIREP is within 1,000 feet of the graphic’s altitude and has been observed within 75 minutes of the chart’s valid time. On CIP/FIP Max product, PIREPs for all altitudes (i.e. 1,000 feet MSL to FL300) are displayed. However, negative reports of icing are not plotted on the CIP/FIP Max product in an effort to reduce clutter. The PIREP legend is located on the bottom of each graphic.

Section 9: New Generation Weather Products Page 9-25

Page 351Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) Graphical Turbulence Guidance (GTG2) The Graphical Turbulence Guidance (GTG) product suite provides a three-dimensional diagnosis and forecast of Clear Air Turbulence (CAT) potential. The GTG is created using a combination of computer model output and turbulence observations. The GTG product suite, which consists of the GTG analysis and forecast and Composite analysis and forecast, is automatically generated with no human modifications. It should be used in conjunction with the report and forecast information contained in an AIRMET and SIGMET. The GTG is available for the 48 contiguous states, much of Canada and Mexico and their respective coastal waters.

Issuance The GTG analysis is issued hourly. The 3-, 6-, 9-, and 12-hour forecasts are issued every three hours beginning at 00Z. For example, a forecast suite issued at 0600Z would have valid times at 0900Z, 1200Z, 1500Z, and 1800Z respectively. The GTG Analysis and Forecasts, along with the Composite products, are issued by the Aviation Weather Center (AWC) and are available through the Aviation Digital Data Service (ADDS) Web site.

Content GTG Analysis and Forecast The GTG Analysis and Forecast graphics depict the location and intensity of potential Clear Air Turbulence (CAT) (Figure 9-22). Standard intensity terminology is used. The GTG output is available for 1,000-foot vertical intervals between 10,000 feet MSL and FL450. ADDS turbulence page displays every second level starting at 10,000 feet MSL, while the ADDS Flight Path Tool provides access to all levels.

Section 9: New Generation Weather Products Page 9-26

Page 352Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014)

Figure 9-22. GTG Example GTG Composite Analysis and Forecast The GTG Composite products display the maximum intensity of potential turbulence between 10,000 feet MSL and FL450 (Figure 9-23). In other words, at any given location, the displayed value represents the maximum potential turbulence between 10,000 feet MSL and FL450.

Single altitude graphics must be examined to determine the altitude of the potential turbulence.

Section 9: New Generation Weather Products Page 9-27

Page 353OCROpen in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) GTG2 - Maximum turbulence intensity (10000 ft. MSL to FL450) Valid 1200 UTC Fri 18 Oct 2013 00-hr forecast from 1200 VTC 18 Oct ADDE None Light Moderate or greater Turb PIREP Symbols 1 Smooth A Light A Moderate A Savera Smooth-Light - A Light-Moderate / Moderate-Severe A Extreme Figure 9-23. GTG Composite Example

9.5.3 Strengths and Limitations The GTG provides an hourly, high resolution analysis and forecast of clear-air eddy dissipation rate (EDR) at and above 10,000 feet MSL. However, the product is only for turbulence associated with upper level fronts and jet streams while other known causes of turbulence are not forecasted.

9.5.3.1 Strengths

• The product is issued hourly

• Turbulence is plotted to a high resolution.

Section 9: New Generation Weather Products Page 9-28

Page 354Open in PDF

Aviation Weather Services, Advisory Circular 00-45G Change 2 (October 2014) Limitations

• T he accuracy of the analysis is dependent on the number of PIREPs available.

Typically at night fewer pilot reports are received, so the accuracy decreases.

• For the GTG forecast, the product is only as accurate the computer model output used to create them.

• The product only displays clear-air turbulence (CAT) for upper-level fronts and the jet stream. Other known causes of turbulence are not included in the product.

• Data and forecast are only available for 11,000 feet MSL and above.

Use The Composite product can provide a quick method to determine what the greatest potential of current or forecast turbulence is at a given location. However, to determine the turbulence potential at any given altitude, the individual altitude products must be viewed.

The ADDS Web site allows users to overlay turbulence PIREPS on the single altitude graphics.

For the PIREP to be plotted on the single altitude product, it must be located within 1,000 feet vertically of the altitude and have been reported within 90 minutes of the chart time. For example, if a user viewed the FL240 GTG product with a valid time of 1400Z the displayed PIREPS could be located between FL230 and FL250 and reported between 1230Z and 1400Z.

Section 9: New Generation Weather Products Page 9-29

Page 355Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 2 (October 2014)

Meteorological Impact Statement (MIS) An MIS is an unscheduled flow control and flight operations planning forecast issued by Center Weather Service Units (CWSUs) (Figures 9-24 and 9-25 and Table 9-5). It is a forecast and briefing product for personnel at Air Route Traffic Control Centers (ARTCCs), Air Traffic Control System Command Center (ATCSCC), Terminal Radar Approach Control Facilities (TRACONS) and Airport Traffic Control Towers (ATCTs) responsible for making flow control-type decisions.

An MIS may be tailored to meet the unique requirements of the host ARTCC. These special requirements will be coordinated between the host ARTCC and the CWSU.

MISs are available on the Aviation Weather Center (AWC) Web site.

Valid Period An MIS is valid up to 12 hours after issuance time and details weather conditions expected to adversely impact air traffic flow in the CWSU area of responsibility. The MIS can be immediately effective for existing conditions when CWSU operations begin or for rapidly deteriorating conditions or be effective up to two hours in advance of expected conditions.

MIS Criteria An MIS enables Air Traffic Control (ATC) facility personnel to include the impact of specific weather conditions in their flow control decision-making. At a minimum, an MIS should be issued when:

• Any of the following conditions occur, are forecast to occur, and, if previously forecast, are no longer expected:

• Conditions meeting convective SIGMET criteria (Section 5.1.8)

• Icing - moderate or greater

• Turbulence - moderate or greater

• Heavy precipitation

• Freezing precipitation

• Conditions at or approaching Low Instrument Flight Rules (IFR)

• Surface winds/gusts >30 knots

• Low Level Wind Shear (surface - 2,000 feet)

• Volcanic ash, dust storms, or sandstorms; and

• In the forecaster's judgment, the conditions listed above, or any others, will adversely impact the flow of air traffic within the ARTCC area of responsibility.

Section 9: New Generation Weather Products Page 9-30

Page 356Open in PDF

Aviation Weather Services, Advisory Circular 00-45G, Change 2 (October 2014)

MIS Issuance MIS phenomena forecasts use the location reference point identifiers depicted on the In-Flight Advisory Plotting Chart (Appendix F), and include the height, extent, and movement of the conditions. MIS product issuances are numbered sequentially beginning at Midnight local time each day. The MIS is disseminated and stored as a "replaceable" product. Therefore, each issuance will contain the details of all pertinent known conditions meeting MIS issuance criteria, including ongoing conditions described in previously issued MISs.

The MIS is for internal use by ARTCC personnel, including Traffic Management Unit (TMU) and TRACON as needed. The MIS is not intended for use by pilots or dispatchers.

Format

Figure 9-24. Meteorological Impact Statement (MIS) Decoding Example

Table 9-5. Meteorological Impact Statement (MIS) – Decoding

LINE CONTENT DESCRIPTION 1 ZFW ARTCC Identification 1 MIS Product type 1 01 Issuance number 1 VALID 190200-191200 Valid period UTC date/time 2 …FOR ATC PLANNING PURPOSES ONLY… Product use statement 3 FROM OKC TO CDS TO GAG TO END TO OKC Phenomenon location 4 LLWS BLO 020 AGL DUE TO LLJ.

CONDS GRDLY IPVG AFT 10Z Phenomenon description Any remarks such as “SEE CONVECTIVE SIGMET 8W"; "NO UPDATES AVBL AFT 0230Z";

and forecaster initials and/or facility identifier may be placed at the end of the MIS.

If the phenomenon described in an MIS is no longer expected, a cancellation MIS message may be issued. The FAA header does not contain an issuance number. If the phenomenon described in the MIS is expected to continue beyond the operating hours of the CWSU, then the remark "NO UPDATES AFT ttttZ" (where "ttttZ" is the UTC closing time of the CWSU) is added at the text end.

Section 9: New Generation Weather Products Page 9-31