3-13
3.6.1.2 Awareness Criteria:
1. Exhibit adequate knowledge of the correct engine start procedures under various atmospheric conditions, normal and abnormal starting limitations, and the proper action required in the event of a malfunction.
2. Ensure ground safety procedures are followed during the before-start, start, and after-start phases.
3. Ensure the use of appropriate ground crew personnel during the start procedures.
4. Consider the effect of jet blast on personnel, other aircraft, vehicles, ground equipment, and structures.
3.6.1.3 Action Criteria:
1. Use required ground crew personnel during the before-start, start, and after-start phases (as appropriate).
2. Start the engine(s) under varying environmental conditions using normal, APU, external power, battery, pneumatic sources, or cross-bleed, as appropriate.
3. Take appropriate action in the event of a malfunction during the start process.
3.6.2 Pushback and Powerback.
3.6.2.1 Condition(s). Select appropriate weather and environmental conditions.
3.6.2.2 Awareness Criteria:
1. Maintain constant vigilance and lookout of the general area around the airplane for hazards to the safety of the airplane, personnel, other aircraft, vehicles, equipment, and structures.
2. Properly divide attention inside and outside the flight deck.
3. Consider the effect of jet blast on personnel, other aircraft, vehicles, ground equipment, and structures.
3.6.2.3 Action Criteria:
1. Maintain proper spacing from other aircraft, obstructions, and personnel.
2. Maintain communications with the ground crew.
3. Avoid use of brakes unless requested by the ground crew.
3-14
3.6.3 Taxi.
3.6.3.1 Condition(s). Select appropriate weather and environmental conditions.
Training must, as required by §§ 119.5(g), 121.415(h), and OpSpec C078, IFR Lower Than Standard Takeoff Minima, 14 CFR Part 121 Airplane Operations - All Airports, as applicable, be conducted in taxi operations at the lowest visibility authorized for takeoff by OpSpecs. Training should also include Surface Movement Guidance and Control System (SMGCS) procedures if the air carrier is authorized to conduct operations at an airport with SMGCS. Refer to the current edition of AC 120-57, Surface Movement Guidance and Control System, for recommended training items for SMGCS.
Refer to the Seaplane, Skiplane, and Float/Ski Equipped Helicopter Operations Handbook (FAA-H-8083-23) for recommended training items for seaplanes.
3.6.3.2 Awareness Criteria:
1. Comply with air carrier and airport low-visibility procedures, as applicable.
2. Exhibit adequate knowledge of safe taxi procedures.
3. Maintain constant vigilance and lookout of the general area around the airplane for hazards to the safety of the airplane, personnel, other aircraft, vehicles, equipment, and structures.
4. Properly divide attention inside and outside the flight deck.
5. Consider the effect of jet blast on personnel, other aircraft, vehicles, ground equipment, and structures.
3.6.3.3 Action Criteria:
1. Use the minimum thrust necessary to breakaway and to maintain taxi speed.
2. Demonstrate proficiency by maintaining correct and positive airplane control.
3. Maintain proper spacing on other aircraft, vehicles, ground equipment, structures, and persons.
4. Maintain desired track and speed.
5. Comply with ATC instructions.
6. Use airport diagram (surface movement chart).
7. Obtain appropriate clearance before crossing or entering active runways.
8. Observe all surface movement guidance control markings and lighting.
3-15
3.6.4 Pretakeoff Procedures.
3.6.4.1 Condition(s). Not applicable.
3.6.4.2 Awareness Criteria:
1. Be aware of the operational factors that could affect takeoff, such as takeoff warning inhibit systems or other airplane characteristics, runway length, surface conditions, wind, wake turbulence, obstructions, and other related factors that could adversely affect safety.
2. Divide attention properly inside and outside flight deck.
3. Be able to determine the need for deicing and/or anti-icing prior to takeoff.
3.6.4.3 Action Criteria:
1. Determine if the airplane is safe for the proposed flight.
2. Determine the airplane’s takeoff performance, considering such factors as wind, density altitude, weight, temperature, pressure altitude, obstructions, and runway condition and length.
3. Determine airspeeds/V-speeds and properly set all instrument references.
4. Configure the FD and autoflight controls, and navigation and communications equipment, to properly fly the airplane in accordance with the ATC clearance.
5. Review procedures for emergency and abnormal situations which may be encountered during takeoff.
6. Obtain and correctly interpret the takeoff and departure clearance as issued by ATC.
7. Confirm that the airplane trim and high-lift devices are configured properly.
8. Complete engine checks.
9. In accordance with the air carrier’s procedures, ensure the wings, control surfaces, and other critical surfaces are free of frost, ice, and snow before flight.
10. Correctly operate anti-icing and deicing systems or equipment.
11. Confirm airplane location and FMS entry (if appropriate) for departure runway prior to crossing hold-short line for takeoff.
3.7 Takeoffs.
3.7.1 Normal Takeoff with All Engines Operating.
3.7.1.1 Condition(s). Select appropriate weather and environmental conditions.
3-16
3.7.1.2 Awareness Criteria:
1. Monitor engine and other airplane controls, settings, and instruments during takeoff to ensure all predetermined parameters are achieved and maintained.
2. Monitor airplane airspeed to determine normal acceleration during takeoff ground roll.
3. Assess takeoff and climb hazards, particularly those related to obstacles.
4. Consider the effect of land-and-hold-short operations (LAHSO), if applicable.
5. Monitor the airplane’s position relative to the departure end of the runway using runway signage, marking(s), and lighting.
3.7.1.3 Action Criteria:
1. Taxi into position to maximize the available runway.
2. Align the airplane on the runway centerline (RCL).
3. Apply the controls correctly to maintain longitudinal alignment on the center line of the runway prior to and during the takeoff.
4. Adjust the engine controls for the existing conditions and verify expected engine performance.
5. Maintain a wings-level attitude during the takeoff roll and during the rotation to proper pitch attitude.
6. For tricycle-gear airplanes, maintain forward pitch control pressure, as necessary, to ensure positive contact of the nose gear with the runway surface for adequate nosewheel/rudder pedal steering capability until sufficient aerodynamic control is achieved.
7. Rotate at the proper airspeed, at the proper rate, to the proper pitch attitude for the airplane configuration.
8. Perform required pitch changes and, as appropriate, perform or call for and verify the accomplishment of, gear and flap retractions, power adjustments, and other required pilot-related activities at the required airspeeds.
9. After lift-off, maintain required ground track or heading ±5°, as appropriate, until a turn is required.
10. Maintain a positive rate of climb throughout the takeoff and initial climb.
11. Adjust to the desired pitch attitude at the predetermined airspeed ±5 knots to attain the desired performance for the particular takeoff segment.
12. Use the applicable noise abatement and wake turbulence avoidance procedures, as required.
3-17
3.7.2 Takeoff with Instrument Meteorological Conditions (IMC).
3.7.2.1 Condition(s):
1. Takeoffs with instrument conditions simulated at or before reaching an altitude of 100 feet above the airport elevation.
2. Takeoffs practiced to proficiency in training under the lowest visibility authorized by the air carrier’s OpSpecs.
3.7.2.2 Awareness Criteria:
1. Comply with normal takeoff awareness criteria in paragraph 3.7.1.2.
2. Exhibit knowledge of an instrument takeoff.
3.7.2.3 Action Criteria:
1. Comply with normal takeoff action criteria in paragraph 3.7.1.3.
2. Transition smoothly and accurately from outside visual references to IMC.
3.7.3 Crosswind Takeoff Including Crosswind Takeoff with Gusts.
3.7.3.1 Condition(s):
1. When conducting training or checking in a flight simulation training device (FSTD), select appropriate weather and environmental conditions, including crosswind with gusts.
2. When conducting training or checking in an airplane in flight, crosswind takeoff with gusts is required, if practicable under the existing meteorological, airport, and traffic conditions.
3. Per § 121.415(h), takeoff with the maximum crosswind for the airplane, as specified in the air carrier’s manual, must be trained to proficiency (if practicable for training conducted in an airplane in flight).
3.7.3.2 Awareness Criteria:
1. Assess the changing effect of the crosswind component to make control corrections, as required.
2. Comply with normal takeoff awareness criteria in paragraph 3.7.1.2.
3.7.3.3 Action Criteria. Comply with normal takeoff action criteria in paragraph 3.7.1.3.
3-18
3.7.4 Takeoff with Simulated Engine Failure.
3.7.4.1 Condition(s). Select appropriate weather and environmental conditions. Per part 121 appendices E and F, takeoff must be demonstrated with a simulated failure of the most critical engine:
1. After takeoff decision speed (V1) and prior to takeoff safety speed (V2);
2. As close as possible after V1 when V1 and V2, or V1 and rotation speed (VR), are identical; or
3. At the appropriate speed for nontransport category airplanes.
3.7.4.2 Awareness Criteria:
1. Comply with normal takeoff awareness criteria in paragraph 3.7.1.2.
2. For nontransport category airplanes, be able to determine the appropriate speed at which the takeoff will continue with an abnormality or emergency.
3. Observe flight and engine instruments or divergence from the RCL to assess loss of thrust.
4. Identify those situations that require a rejected takeoff and make a timely decision to continue the takeoff or reject the takeoff.
5. Identify the location of the engine failure (e.g., right side, left side, or center).
3.7.4.3 Action Criteria:
1. Comply with normal takeoff action criteria in paragraph 3.7.1.3.
2. Apply rudder as required to counteract asymmetric thrust.
3. Maintain the airplane alignment with the runway.
4. For transport category airplanes, continue the takeoff if an abnormality or emergency occurs at or after V1 speed. For nontransport category airplanes, continue the takeoff if an abnormality or emergency occurs at or after the predetermined speed.
5. Transition smoothly and accurately into a stabilized climb, achieving and maintaining the airplane in coordinated flight.
6. Maintain the required ground track (or heading) and attitude appropriate for climb performance and terrain clearance, as appropriate, until a turn is required.
7. Make a suitable decision to return to airport or divert, as appropriate.
3-19
3.7.5 Rejected Takeoff.
3.7.5.1 Condition(s). Select appropriate weather and environmental conditions. The cause for the decision to reject needs to be presented so that the first action to reject the takeoff may be made by, (1) V1 speed for transport category airplanes or (2) a predetermined speed for nontransport category airplanes.
Rejected takeoffs should be conducted in realistic scenarios, such as:
1. Airspeed discrepancies;
2. Takeoff configuration warnings;
3. Cargo or cabin door warnings;
4. Mechanical issues;
5. Tire failures;
6. ATC instruction to reject or canceled clearance;
7. Bird strike;
8. Engine failure; or
9. Other scenarios, that per the air carrier’s manual, should require a rejected takeoff.
3.7.5.2 Awareness Criteria:
1. Identify a critical situation and take action to reject the takeoff prior to either V1 speed for transport category airplanes or a predetermined speed for non-transport category airplanes.
2. For nontransport category airplanes, be able to determine the appropriate speed at which the takeoff will continue with an abnormality or emergency.
3.7.5.3 Action Criteria:
1. Reduce the power promptly to idle and simultaneously apply maximum wheel brakes when a cause for aborting the takeoff is recognized.
2. Use spoilers, thrust or propeller reverse, and other drag or braking devices, as appropriate, to bring the airplane to a safe stop on the runway or stopway surface.
3.8 In-Flight Maneuvers. The purpose of these maneuvers is to provide familiarity with the handling behavior of the airplane. The intent is to teach the pilot to recognize deviation from normal flight and to practice the return of the airplane to a safe state. In this context, a safe state is considered an airplane attitude (e.g., pitch, bank, and yaw), airspeed, trim, and thrust setting appropriate for the airplane configuration and altitude at which the pilot is able to maintain control of the airplane. If the instructor or check pilot requires the assistance of the pilot to maneuver or configure the airplane, to fly a particular airspeed,
3-20 or to set a particular power or trim setting, the instructor or check pilot should provide progressive instructions to the pilot to achieve the desired “set up” position for the task.
Returning the airplane to a safe state requires that the pilot continue to control the airplane away from attitudes and airspeeds that would exceed critical performance parameters (e.g., airspeed limits and “G” loading).
3.8.1 Turns With and Without Spoilers.
3.8.1.1 Condition(s):
1. The airplane may be equipped with ailerons or a combination of ailerons and roll control flight spoilers. For those airplanes equipped with a combination of ailerons and roll control flight spoilers, this maneuver should be accomplished without the roll control flight spoilers.
2. Training should include use of manual and autoflight controls at altitudes, airspeeds, airplane configurations, and environmental conditions representative of normal operations during departures, arrivals, and cruise.
3.8.1.2 Awareness Criteria. Experience the handling qualities of the airplane with various spoiler configurations.
3.8.1.3 Action Criteria:
1. Make turns left and right with a normal flight control configuration.
2. Make turns left and right with ailerons only.
3.8.2 Mach Tuck and Mach Buffet.
3.8.2.1 Condition(s). Select appropriate weather and environmental conditions.
3.8.2.2 Awareness Criteria. Experience the handling qualities of the airplane at high Mach numbers.
3.8.2.3 Action Criteria:
1. Increase airspeed slowly.
2. Observe the performance of the compensating device or system, if installed.
3. Disable the compensating device or system, if installed, and continue to accelerate until the tuck or buffet occurs.
4. Observe the airframe vibration and/or flight instrument indications.
5. Make a shallow level turn to feel the increased buffeting associated with an increase in G load.
3-21
3.8.3 En Route Navigation.
3.8.3.1 Condition(s). All.
3.8.3.2 Awareness Criteria:
1. Monitor fuel burn, cruise speed, and thrust to achieve planned performance.
2. Monitor navigation system performance.
3. Understand maximum operating altitude and optimum cruise altitude.
3.8.3.3 Action Criteria:
1. Use Class I or oceanic and remote continental airspace navigation procedures as authorized by the OpSpecs and prescribed by the air carrier’s manual.
2. Navigate to the degree of accuracy required by the airspace in which the airplane is being operated.
3. Conduct required navigation system crosschecks.
4. Perform correct altimetry procedures and monitor flight level or altitude clearances.
5. Report equipment failure that may degrade navigation as dictated by airspace or regional differences.
6. Determine the optimum cruise altitude for a given gross weight and desired airspeed or Mach.
7. Use appropriate onboard reference to determine the maximum cruise altitude for the gross weight that affords the required maneuver buffet margin.
3.8.4 Runaway Pitch Trim or Stabilizer.
3.8.4.1 Condition(s). Select appropriate weather and environmental conditions.
3.8.4.2 Awareness Criteria:
1. Experience the pitch handling qualities of the airplane with runaway stabilizer or runaway pitch trim during takeoff, cruise, and landing.
2. Observe the effects of early versus late detection of runaway.
3. Observe the effects of deactivation of pitch trim or stabilizer or correction of runaway.
3-22
3.8.4.3 Action Criteria:
1. Identify runaway pitch trim or stabilizer.
2. Take appropriate action to stop runaway.
3. Disengage autoflight, as appropriate.
4. Use alternative methods to control pitch, such as manual stabilizer trim and thrust.
5. Use PM and Crew Resource Management (CRM), as necessary, to maintain control of pitch.
6. Comply with runaway trim procedures provided in the air carrier’s manual.
3.8.5 Jammed Pitch Trim or Stabilizer.
3.8.5.1 Condition(s). Select appropriate weather and environmental conditions.
3.8.5.2 Awareness Criteria:
1. Experience the pitch handling qualities of the airplane with jammed stabilizer or pitch trim during takeoff, cruise, and landing.
2. Observe the effect of an increase and decrease in airspeed.
3. Recognize the insidious nature of the failure during periods of unaccelerated flight.
3.8.5.3 Action Criteria:
1. Identify jammed pitch trim or stabilizer.
2. Disengage autoflight, as appropriate.
3. Use alternative methods to control pitch, such as thrust.
4. Use PM and CRM, as necessary, to maintain control of pitch.
5. Comply with runaway trim procedures provided in the air carrier’s manual.
3.8.6 Steep Turns.
3.8.6.1 Condition(s). Per part 121 appendices E and F, each steep turn must involve a bank angle of 45° with a heading change of at least 180°, but not more than 360°.
3.8.6.2 Awareness Criteria. Exhibit knowledge of factors associated with steep turns, including wing loading, angle of bank, stall speed, pitch, power requirements, and overbanking tendency.
3-23
3.8.6.3 Action Criteria:
1. Apply smooth coordinated pitch, bank, and power to maintain the specified altitude within ±100 feet, airspeed within ±10 knots, and bank angle of 45° ±5°.
2. Complete a steep turn of at least 180° left and right.
3. Roll out of steep turn within ±10° of specified heading.
3.8.7 Recovery From Specific Flight Characteristics Peculiar to the Airplane Type.
3.8.7.1 Condition(s). Select appropriate weather and environmental conditions.
Specific flight characteristics are identified in the Flight Standardization Board (FSB) Report for the specific airplane.
3.8.7.2 Awareness Criteria. Exhibit knowledge of the specific flight characteristics appropriate to the specific airplane type.
3.8.7.3 Action Criteria. Use proper technique to recover from specific flight situations.
3.8.8 Manually Controlled Slow Flight. Refer to the current edition of AC 120-111, Upset Prevention and Recovery Training.
3.8.9 Stall Prevention.
3.8.9.1 Condition(s). Select appropriate weather and environmental conditions:
1. Per part 121 appendices E and F, recovery procedures must be initiated at the first indication of an impending stall (e.g., buffet, stick shaker, aural warning).
2. Per part 121 appendices E and F, stall prevention must be conducted in at least the following configurations:
• Takeoff configuration (except where the airplane uses only a zero-flap takeoff configuration);
• Clean configuration; and
• Landing configuration.
3. The pilot should not be expected to be proficient in executing the method used to enter the maneuver.
3.8.9.2 Awareness Criteria. Refer to the current edition of AC 120-109, Stall Prevention and Recovery Training.
3.8.9.3 Action Criteria. Refer to AC 120-109.
3-24
3.8.10 Full Stall Recovery.
3.8.10.1 Condition(s). Select appropriate weather and environmental conditions.
1. This maneuver should only be conducted during training in an FSTD. This maneuver should not be conducted in an airplane in flight.
2. This maneuver should be conducted as instructor guided hands-on experience of recovery from full stall and stick pusher activation, if equipped.
3.8.10.2 Awareness Criteria. Refer to AC 120-109.
3.8.10.3 Action Criteria. Refer to AC 120-109.
3.8.11 Upset Prevention and Recovery. Refer to AC 120-111.
3.8.12 Manually Controlled Loss of Reliable Airspeed.
3.8.12.1 Condition(s):
1. Select appropriate IMC weather and environmental conditions for the task.
2. This event may be conducted in any phase of flight.
3. Select appropriate maneuvers for the selected phase of flight to then be accomplished with sole reference to pitch and power.
3.8.12.2 Awareness Criteria. Refer to AC 120-111.
3.8.12.3 Action Criteria. Refer to AC 120-111.
3.8.13 Operation of Systems and Controls at the Flight Engineer’s (FE) Panel.
3.8.13.1 Condition(s). All environmental conditions and circumstances.
3.8.13.2 Awareness Criteria:
1. Demonstrate an understanding and proper use of the systems, controls, and displays represented on the FE’s panel.
2. Demonstrate an understanding of the relationship of the airplane’s phase of flight, how to assess the status of the airplane’s systems, and when to take necessary corrective actions.
3.8.13.3 Action Criteria. Be familiar with the systems and properly exercise the controls represented at the FE’s panel during all phases of flight.