CHAPTER 5. ACCOMPLISHMENT AND APPROVAL OF MAINTENANCE AND
ALTERATIONS
500. ACCOMPLISHMENT OF MAINTENANCE.
a. As a maintenance entity, you have authorization under §§ 43.3(f), 43.7(e), 121.379, and
135.437 to perform maintenance on your own air carrier aircraft and to approve them for return to service without obtaining any other maintenance certification. In addition, §§ 121.379 and
135.437 provide clear authority for you, under your air carrier certificate, to perform maintenance on behalf of other air carriers who conduct operations under the same part as you do. You may also perform maintenance for an air carrier or other operator conducting operations under a different part than you are. However, we did not include this maintenance in your air carrier maintenance authority; therefore, you must separate any maintenance that you perform under this circumstance so that it is independent of your authority and certification as an air carrier.
b. Each individual who makes an airworthiness determination on your behalf must hold an appropriate airman’s certificate. Sections 121.378 and 135.435 require that any individual who you put directly in charge of performing maintenance hold an airman certificate. Section 121.371 requires that any individual that you authorize to perform RII for you hold an appropriate airman certificate. Section 121.709 requires that anyone who you authorize to issue an approval for return to service hold an appropriate airman’s certificate. Your DOM and chief inspector must hold an airman’s certificate with Airframe and Powerplant (A&P) ratings. These certificate requirements are air carrier qualification requirements, not requirements for an airman certificate that the individual needs to do maintenance. You accomplish all maintenance and approval for return to service on your aircraft under your air carrier certificate by your maintenance organization or persons authorized by you, not by any individual or organization under their own individual certificate. There is, however, one exception to the individual airman certificate requirement. It occurs if you arrange for a certificated repair station located outside the United States to perform maintenance. At such repair stations, individuals directly in charge of performing maintenance or required inspections are not required to hold an FAA airman certificate.
501. MAJOR REPAIRS AND ALTERATIONS. Under §§ 121.379(b) and 135.437(b), major repairs and alterations must be done in accordance with technical data approved by the FAA.
Appendix A to part 43 contains a list of repairs and alterations that are considered to be major.
However, you should note that the Civil Aeronautics Administration (CAA) published a list of repairs and alterations to specific parts, as well as specific types of repairs that were considered major repairs during 1953. The CAA later adopted this major repair and alteration list, unchanged, as part of appendix A of part 43. Exclusive reliance on the part 43 appendix A list of major repairs and alterations to make the major/minor classification will result in the classification of some minor repairs as major and classification of some major repairs as minor simply because the appendix A list has not been updated to include evolving airplane design and construction techniques such as composite structures and the high-speed, high-altitude pressurized jet transport that did not exist when the CAA developed the list. You should have detailed major/minor classification procedures in your manual to evaluate each repair or alteration on a case-by-case basis using such factors as the certification basis of the aircraft;
Par 500 Page 15
classification of the structure as primary, secondary, or a primary structural element; or classification as a fail-safe, safe-life, or damage-tolerant structure.
502. AIRWORTHINESS RELEASE FORM OR AIRCRAFT LOG ENTRY AND APPROVAL FOR RETURN TO SERVICE. After performing any maintenance on your airplane, you must approve it for return to service before you may operate it. As an air carrier, you must issue an approval for return to service under § 121.709 or § 135.443 as appropriate.
You can read additional, more detailed information about the process for approving your airplanes for return to service in Chapter 8.
503. SCOPE OF MAINTENANCE. You must provide instructions in your maintenance program and maintenance manual for maintenance and alterations encompassing the four areas of “what to do,” “when to do it,” how to do it,” and “was it done properly” in at least three major areas: scheduled maintenance, unscheduled maintenance, and specific maintenance requirements for major components of the aircraft.
a. Scheduled Maintenance. Scheduled maintenance consists of all the individual maintenance tasks performed according to the maintenance time limitations (maintenance schedule). Your scheduled maintenance activities should include procedural instructions for the maintenance tasks and requirements to record the results of the inspections, checks, tests, and other maintenance. Your procedures should also provide for time-related activities such as recurring ADs, Certification Maintenance Requirements (CMR), and life-limited parts retirement.
b. Unscheduled Maintenance. Unscheduled maintenance includes procedures, instructions, and standards for maintenance that occurs on an unscheduled or unforeseen basis. A need for unscheduled maintenance may result from scheduled maintenance tasks, pilot reports, or unforeseen events, such as high-load events, hard or overweight landings, tail strikes, ground damage, lightning strikes, or an engine over-temperature. In your maintenance manual, you should include instructions and standards for the accomplishment and recording of unscheduled maintenance and detailed procedures for recording all types of unscheduled maintenance.
c. Specific Maintenance Requirements for Major Aircraft Components.
(1) Engine Maintenance Program. Your engine maintenance program should cover the maintenance of installed engines and off-wing engines for each engine model you operate. If your aircraft has auxiliary power units (APU), you may want to include APU maintenance as part of your engine maintenance program. Usually, the installed engine or APU requirements will be contained in the maintenance time limitations. In addition to procedural information, the off-wing program described in your maintenance manual should provide shop scheduling information or intervals for cleaning, adjusting, inspecting, testing, and lubricating each part of the engine or APU requiring that maintenance. You should include in your maintenance manual the degree of inspection, the applicable wear tolerances, and the work required when the engine or APU is in the shop.
(2) Propeller Maintenance Program. If applicable, your propeller maintenance program should cover the maintenance of installed propellers and off-wing propellers for each Page 16 Par 501
Par 503 Page 17 (and 18) model you operate. Usually, the installed propeller system scheduled maintenance requirements will be contained in the maintenance time limitations. In addition to procedural information, the off-wing program described in your manual should provide shop scheduling information or intervals for cleaning, inspecting, adjusting, testing, and lubricating each part of the propeller system requiring that maintenance. You should include in your maintenance manual the degree of inspection, the applicable wear tolerances, and the work required at these periods. Some modern propellers are constructed of composite materials and, therefore, may require unique tools, repair procedures, and specialized training for your maintenance personnel.
504. PARTS AND APPLIANCES MAINTENANCE PROGRAM. For the most part, this component of your maintenance program covers shop operations, which may include both scheduled and unscheduled tasks. You may conduct these shop operations at some location other than where you perform maintenance on your aircraft. Your parts and appliance maintenance program should cover both installed parts and appliances and off-wing maintenance for each part and appliance model that you operate. Usually, the installed part and appliance scheduled maintenance requirements will be contained in the maintenance time limitations. In addition to procedural information, the off-wing program described in your maintenance manual should provide shop scheduling information or intervals for cleaning, adjusting, inspecting, testing, and lubricating each component of the part and appliance requiring that maintenance. Include in your maintenance manual the degree of inspection, the applicable wear tolerances, and the work required when the part or appliance is in the shop.
Par 600 Page 19 CHAPTER 6. MAINTENANCE SCHEDULE
600. THE MAINTENANCE SCHEDULE. Sections 119.49 and 121.135(b) require you to have maintenance time limitations, also called a maintenance schedule. These same rules permit you to use standards for determining your maintenance time limitations. This language is the regulatory basis of FAA-approved reliability programs that we developed in the 1960s. The maintenance time limitations set out the what, how, and when of your scheduled maintenance effort. Although in the past the schedule included only basic overhaul limits and other general requirements, today it includes a specific list of each individual maintenance task and its associated time limit. The regulations are broad enough to permit you to organize all of these individual tasks into a series of integrated scheduled work packages of your own design that provide a continuous succession of necessary or desirable scheduled maintenance tasks for your entire airplane.
601. THE FAA’s ROLE IN RELATION TO THE MAINTENANCE SCHEDULE. The FAA authorizes your maintenance schedule through your OpSpecs, and your CASS monitors that schedule to verify its effectiveness (i.e., producing the desired results). Your CASS will be your principal source of information that might indicate a needed change to your maintenance schedule. (We describe the CASS in Chapter 11 and in much more detail in AC 120-79.) We expect you to correct any deficiencies in your maintenance schedule. Under §§ 121.373(b) and
135.431(b), if you do not make needed changes, we can require you to change your maintenance schedule or any other element of your maintenance program found deficient.
602. MAINTENANCE SCHEDULE CONTENTS.
a. Maintenance Schedule Should Contain the Following Information:
(1) What (Unique Identifier). This is the item that you are going to maintain. Your identifier should be specific enough to allow the individual that you assign to do the scheduled maintenance task to easily and accurately identify the item.
(2) How (Task). How to maintain the item; the scheduled maintenance task to be done.
A scheduled maintenance task is a maintenance action that you perform at regular, scheduled intervals so that you can ensure the item can continue to perform its intended function within its operating context, or so you can discover a hidden failure, or to ensure that a hidden function is available. You should not use terms such as hard-time (HT), on-condition, or condition monitored in your maintenance schedule. These terms represent obsolete 1960s methodology, are vague, and do not describe the maintenance task you are performing. If your maintenance schedule contains these terms, there is a risk that the scheduled maintenance that you want and need may not be the maintenance that is being performed.
(3) When (Frequency). Frequency is the time in service interval between the time when you accomplish a scheduled maintenance task. You may measure time in service intervals in calendar-time, operational hours, flight cycles, or any other appropriate parameter. In addition, for task management, inventory, and audit purposes, you should identify, on the maintenance schedule, the task or work card associated with each scheduled maintenance task. This way, you
can ensure that you accomplish all of your scheduled maintenance tasks according to your schedule.
b. Your overall maintenance schedule objective is to do the correct tasks at the correct interval. Keep in mind that more maintenance is not always a good idea, so if you decide to decrease intervals or add tasks, you should go through the same justification process as any other change to the maintenance schedule.
603. STANDARDS FOR DETERMINING MAINTENANCE TIME LIMITATIONS. As we mentioned in paragraph 600, §§ 119.49 and 121.135 permit you to have standards for determining your maintenance time limitations. In the past, we used this language as the regulatory basis for FAA-approved reliability programs that evolved during the 1960s. These programs were based on the Air Transport Association of America’s (ATA) now obsolete process-based Maintenance Steering Group – 2nd Task Force (MSG-2) decision logic that focused on failure rates and maintaining individual parts of the aircraft. Consistent with the continuous evolution of aviation, MSG–2 became obsolete in 1980 with the advent of ATAs task-based Maintenance Steering Group – 3rd Task Force (MSG-3) decision logic. MSG-3 focused on aircraft systems and a loss of function rather than an individual part failure. In any case, the management of these MSG-2 process-based programs was actuarial analysis. Air carriers used the failure rates of a part to determine, through a probability process, the likelihood that the part would have a similar failure rate in the future. The standard was the acceptable failure rate. Air carriers used a failure rate alert program with upper control limits (UCL) and lower control limits (LCL) to track part failure rates. The air carrier was obliged to take action only when the failure rate deviated from the probability-based prediction (i.e., exceeded the UCL or the LCL). If the part did not respond, the air carrier had authorization to move the UCL or LCL to make the failure rate within the alert program limits.
a. During the 1970s, after collecting a large amount of operational data over time, the industry came to the realization that using failure rates and alert programs was not the most effective way of managing scheduled maintenance. Using the vast amount of operational data that was available, United Airlines developed and published a report during 1978 under a U.S.
Department of Defense (DOD) contract entitled “Reliability Centered Maintenance (RCM).”
This very significant document was in stark contrast to the previous part failure rate focus. RCM focused on the loss of function of an aircraft system. RCM determined that everything doesn’t fail the same way; failures occur according to six different failure patterns. RCM also determined that everything doesn’t require the same type of maintenance; there are four different types of scheduled maintenance. RCM also took into account the different consequences (safety, operational, and economic) of a loss of function, as well as system functional redundancy and inherent design safety when determining if scheduled maintenance was required. In some cases, RCM determined that no scheduled maintenance was required. This resulted in doing only required maintenance and a much lower maintenance burden.
b. The RCM document was the major basis for the ATA’s development of the MSG-3 decision logic in 1980. Since then, most aircraft manufacturers have used the ATA’s MSG-3 decision logic to help them develop scheduled maintenance requirements for their new products.
Besides providing organization and flow to the deliberative process, the primary attribute of the MSG-3 process is that the user can develop initial scheduled maintenance requirements without Page 20 Par 602
Par 603 Page 21 (and 22) the operational data that is required to determine the need for scheduled maintenance tasks.
Using the techniques of the MSG-3 decision logic, it is fairly simple to decide what tasks are required to be included in an initial scheduled maintenance program. However, the MSG-3 decision logic does not contain task interval selection decision logic to help the user determine where to set the task intervals, or how to adjust them after service is initiated. Using the MSG-3 process, initial task intervals are set on the basis of knowledge of the design, and the best judgment of the working group members. Under MSG-3, initial intervals are, essentially, a best guess. As a result, validation of initial interval selections must occur when the aircraft begins service and starts generating the operational data that was not available when the initial intervals were set.
c. An inherent function of your CASS is to determine the effectiveness of your scheduled maintenance effort through operational data collection and analysis activity. You use this important function to determine the level of scheduled maintenance effectiveness and to make the changes necessary to achieve the standard of effectiveness that you have set. Effective means “it is producing the desired results.” Thus, from an operational standpoint, an indicator of effectiveness of your scheduled maintenance effort is the availability of your aircraft for flight operations. If your aircraft are unavailable for flight operations due to maintenance reasons, then your scheduled maintenance program may not be as effective as it should be. There may be other elements of your maintenance program besides the scheduled maintenance element that may be deficient as well, but your CASS procedures will identify the root cause and help you identify and make the adjustments/changes necessary to achieve the level of flight operations availability (the result) that you have set.
Par 700 Page 23 CHAPTER 7. REQUIRED INSPECTION ITEMS
700. RIIs.
a. Tasks as RIIs. Sections 121.369(b) and 135.427(b) require you to designate certain tasks as RII. Your RIIs must designate those items of maintenance and alteration that you must inspect (required inspections), including at least those that could result in a failure, malfunction, or defect that endangers the safe operation of the aircraft if you do not do it properly or if you use improper parts or material. If other persons perform maintenance tasks for you, you may authorize them to accomplish your RII requirement, provided that your manual satisfies the regulatory requirements, as outlined in paragraph 701. Consistent with the regulations, you remain primarily responsible for the performance of each RII accomplished by the other person.
b. Making RII Lists. With consideration of the exception at §§ 121.378(a) and
135.435(a), each individual that you grant an RII authorization to must hold an appropriate airman’s certificate. Instead, you should identify specific items of inspection for each aircraft type (it is inappropriate to designate entire systems as RII). You should adhere to a decision process, similar to the following, when creating a list of RIIs:
FIGURE 7.1. REQUIRED INSPECTION ITEMS Page 24 Par 700
c. RIIs and Safety. RIIs relate directly to flight safety. Consider all your RIIs with the same safety of flight consideration and emphasis even if accomplishing an individual RII adversely impacts your flight schedule, it is related to a scheduled or an unscheduled task, or it arises at an awkward time or at an inconvenient location.
701. RII PROCEDURES, STANDARDS, AND LIMITS.
a. List of Other Persons. Your manual must include a list of persons with whom you have arranged for the performance of any required inspections (§§ 121.369(a) and 135.427(a)) both within your organization and within other organizations that perform maintenance on your behalf. This listing must include a designation by occupational title of the personnel authorized to perform each required inspection (§§ 121.369(b)(3) and 135.427(b)(3)).
b. Certification. With consideration of the exception at §§ 121.378(a) and 135.435(a), each individual that you grant an RII authorization to must hold an appropriate airman’s certificate. This is an air carrier qualification requirement; the individual does not exercise that certificate when accomplishing the RII. You must formally notify each of these individuals of their RII authorization as well as its scope (§§ 121.371(d) and 135.429(e)).
c. RII Requirements. You should clearly identify your RII requirements on work forms, job cards, engineering orders, etc., or by any other method consistent with your maintenance program. A primary concept of the RII function is to prevent any person who performs any item of work from performing any required inspection of that work (§§ 121.369(b)(7) and
135.427(b)(7)). Therefore, it is important that you identify RIIs whenever possible so that everyone knows that an RII is required. You should also clearly state RII buy-back procedures (§§ 121.369(b)(4) and 135.427(b)(4)).
d. Standards and Limitations. You must set procedures, standards, and limits necessary for required inspections and acceptance or rejection of the RII (§§ 121.369(b)(5) and
135.427(b)(5)). You should have those procedures, standards, and limits necessary for the accomplishment of your required inspections. You must also have those procedures, standards, and limits necessary for the acceptance or rejection of each of your RIIs. As you will not find RIIs or procedures, standards, and limits for required inspection items in an OEM manual, you will have to develop these and put them in your manual. Your manual must specify the method of performing required inspections (§§ 121.369(b)(3) and 135.427(b)(3)).
e. Procedures. Your manual must include procedures to ensure that you perform and complete all required inspections (§§ 121.369(b)(6) and 135.427(b)(6)) before you release the aircraft to service (§§ 121.369(b)(9) and 135.427(b)(9)).
Par 700 Page 25 (and 26)
Par 800 Page 27 CHAPTER 8. MAINTENANCE RECORDKEEPING SYSTEM
800. REASONS FOR MAKING AND KEEPING MAINTENANCE RECORDS. Your primary reason to make and retain air carrier maintenance records is to show that the U.S. Standard Airworthiness Certificate on your aircraft is effective and that your aircraft is Airworthy. A U.S. standard airworthiness certificate is effective only as long as the maintenance and alterations are performed according to the requirements of the FAA’s regulations. If your required aircraft maintenance records are incomplete or inaccurate, it can render your aircraft’s Standard Airworthiness Certificate ineffective. Maintenance actions, in almost all cases, become intangible or abstract after the fact. Therefore, in order for you to make a maintenance action tangible, you must make a record of that maintenance action. Additionally, making a record of certain summary information supports identification of the current inspection and airworthiness status of your aircraft.
801. PART 43 REQUIREMENTS. You can find the basic requirement to make a maintenance record in § 43.9(a); however, § 43.9(b) indicates that the governing requirements for you, an air carrier, are found in part 121 or 135. That is another way of saying that the recordkeeping requirements of § 43.9(a) do not apply to you. However, the requirements of § 43.9(b) are consistent with the air carrier maintenance recordkeeping requirements of §§ 121.369(c) and
121.380(a) and (c), or §§ 135.427(c) and 135.439.
802. WORK PERFORMED BY A PART 145 REPAIR STATION.
a. Part 145, § 145.219 sets forth requirements for a certificated repair station to retain certain records of maintenance that it performs. It also requires the repair station to make those records available to the FAA. However, these §§ 43.9(a) and 145.219 requirements do not apply when the repair station is accomplishing any work on your aircraft.
b. The wording of the § 145.205 regulations, as well as §§ 119.1(c), 121.1(b), and
135.1(a)(2), compel a part 145 certificated repair station to follow the procedures and requirements of your maintenance program and applicable sections of your maintenance manual when accomplishing any maintenance or alterations on your aircraft. Consequently, a certificated repair station must use the performance standards of part 121 or 135, including the recordkeeping requirements, instead of following the provisions in part 145 and the repair station’s repair station manual. This is consistent with the requirements of the Paperwork Reduction Act, which does not permit the government to require two separate but identical sets of records. The responsibility for retaining records in accordance with the retention requirements of §§ 121.380(c) and 135.439(b) rests with you, the air carrier, not the repair station. However, if a part 145 repair station wants to retain a copy of those records generated by working on your aircraft, our regulations do not preclude them from doing so. Asking the part 145 repair station to keep your records for you is consistent with regulations, although you are responsible for retaining them and making them available to the FAA. This is consistent with the requirements of § 119.59(c).
803. PENALTIES FOR IMPROPER AIR CARRIER MAINTENANCE RECORDKEEPING.
a. Maintenance Records are Important for:
(1) You, as operator, to fulfill your responsibility to determine the airworthiness status of your aircraft.
(2) Us, to use them for its continuing review of aircraft maintenance records as a direct means of determining the airworthiness and safety status of air carrier aircraft.
b. Reviewing Maintenance Records. Because reviewing maintenance records is often the only direct means of determining the accomplishment of required maintenance, Federal law treats the act of intentionally failing to make and keep, as well as the act of intentionally falsifying, mutilating, or altering air carrier aircraft records, as a criminal act subject to the imposition of substantial fines and/or imprisonment.
804. MAKING AND KEEPING REQUIRED RECORDS.
a. Recordkeeping System. FAA regulations (§ 121.369(c) or § 135.427(c)) require you to have and use a recordkeeping system for the preparation, storage, and retention of required aircraft maintenance records. You must document your system in your maintenance manual. The primary objectives of these systems are the generation, storage, retention, and retrieval of accurate and complete air carrier aircraft maintenance records. As stated earlier, these records are primarily made to show that the U.S. Standard Airworthiness Certificate of your air carrier aircraft is effective, and your aircraft is Airworthy and capable of safe flight.
b. Record Locations. FAA regulations (§ 119.59(b)(1)(ii)) also require you to make and keep a listing that identifies the location of each record, document, and report that you are required to make and keep, as well as a listing that identifies each person that is responsible for each of those records, documents, and reports.
c. ADs. FAA regulations §§ 121.380(a)(2)(vii) and 135.439(a)(2)(v) also require you to keep a record of the current status of applicable ADs, including the date and methods of compliance, and, if the AD involves recurring action, the time and date when the next action is required.
805. REQUIRED AIR CARRIER MAINTENANCE RECORDS. Current requirements found in §§ 121.380 and 135.439 call for two types of records: a list of current status information and air carrier airworthiness release form records.
806. WHEN TO MAKE RECORDS AVAILABLE TO THE FAA. Section 119.59(c) mandates you must make your air carrier maintenance records available to us. We can require you to make your records available to us at any time.
807. RESPONSIBILITY FOR MAKING RECORDS AVAILABLE TO THE FAA. Under § 119.59(b)(1), you must make a list of persons in your organization that you have designated to be responsible for making each required maintenance record, document, or report available to the Page 28 Par 803
FAA upon request. You must make a list of the location of each record, document, or report.
You must keep this list current and make it available to the FAA at your principal base of operations.
808. REQUIRED RECORDS. You are required to make and keep certain current status records. Current status recordkeeping requirements are listed in §§ 121.380 and 135.439 and explained as follows:
a. Total Time in Service. The total time in service of the airframe, each installed engine, and each installed propeller is a record that contains the time in service accrued since new or rebuilt, expressed in hours, landings, or cycles.
NOTE: It is important for you to know that rebuilt does not have the same meaning as overhauled (§ 43.2(b)).
b. Current Status of Each Life-Limited Part. The current status of each life-limited part of each airframe, engine, propeller, and appliance means a record that contains at least the following information:
(1) Time in service since new, expressed in the appropriate parameter (hours, cycles, calendar-time);
(2) The time in service remaining to the specified life limit expressed in the appropriate parameter (hours, cycles, calendar-time);
(3) The specified life limit expressed in the appropriate parameter (hours, cycles, calendar-time); and
(4) A record of any action that alters the part’s life limit or changes the parameter of the life limit.
NOTE: If you conduct operations under part 135, total time in service and the current status of life-limited parts also includes rotors.
c. Time Since Last Overhaul. The listing of the time since last overhaul means a record that contains at least the following information:
(1) An identification of the item that requires overhaul and its associated scheduled overhaul interval,
(2) The time in service since the last overhaul was accomplished,
(3) The time in service remaining until the next scheduled overhaul is due, and
(4) The time in service when the next scheduled overhaul is due.
NOTE: The listing of time since last overhaul refers to summary current status information. You must not confuse it with an overhaul record, which is Par 807 Page 29