3-2
3.5 Timetable for Certification. At the initial informal meeting the FAA will review with you the steps necessary to develop the formal application and complete certification.
They will also assist you in determining the timetable you should meet in order to complete all aspects of preparing for, and completing, certification by the date you plan to begin operations under part 125.
3.6 Should You Submit a Request for Deviation Authority? After initial contact with the FSDO or IFO, as applicable, you should begin the process of deciding whether or not a deviation request from 14 CFR part 119, § 119.23(a)(3) and § 125.5 (the requirement to hold an operating certificate and operations specifications (OpSpecs)) will be required for your operation. You should consider early whether or not to submit a request for an A125 Letter of Deviation Authority (LODA) authority to deviate from certain sections of part 125. Chapter 10 outlines the procedures for making this request.
3.7 Determine How You Will Comply with Part 125.
3.7.1 Compliance Statement/Letter of Compliance. You will be required to submit a compliance statement/letter of compliance which summarizes, for each applicable part 125 section, how your organization intends to comply with part 125, and the applicable sections of 14 CFR parts 91 and 119.
3.7.2 Manual References. When developing the compliance statement/letter of compliance, a determination should be made of which sections of part 125 will be included in your Policy and Procedures Manual (PPM) to satisfy the type(s) of operations planned. In the compliance statement, your intentions should be specifically referenced as to the location in the manual of how you will otherwise assure compliance with the applicable sections.
3.8 Developing Company Manuals.
3.8.1 Manual’s Contents. After the operation planning has been completed, the next step would be the formulation of the policies and procedures that you want company personnel to follow in the performance of their duties. Part 125 requires these policies and procedures to be contained in a manual and specifies the required contents (refer to §§ 125.71,
125.73, and 125.249). Contents other than that required by the rule may be part of your PPM, as applicable to your operation.
3.8.2 Manual Formulation Guidance. Specific guidance on the formulation of this manual is included in Chapter 7 and Appendix A.
3.8.3 Approved Flight Manual. Section 125.75 requires that you have FAA-approved flight manuals for each airplane. Procedures should assure that these manuals are up-to-date and available to the crewmembers as required by § 125.71(e). Modifications to the operating procedures and performance data must be approved by the FAA (refer to § 125.75(b)).
3-3
3.9 Minimum Equipment List (MEL).
3.9.1 MEL Definition. An MEL is a method by which a part 125 holder can, under controlled conditions, operate an airplane with specified items of equipment inoperative until repairs are available or feasible. Authority for the use of an approved MEL is provided in § 125.201(a).
3.9.2 MEL Guidelines. Items of equipment required on an airplane may be dictated by the airplane type certificate, the operational requirements (e.g., part 125), or, in the case of optional equipment, by the operator. The MEL is developed by the operator from the Master Minimum Equipment List (MMEL). The MEL submitted by the operator may not be less restrictive than the MMEL from which it was developed, and provides for approval to deviate under controlled conditions from certain operational requirements.
These “controlled conditions” may be restrictions from flight during night, in instrument flight rules (IFR) or icing conditions, or by changes in in-flight operational procedures, temporary deactivation of components, or other procedures.
3.9.3 Approval of MEL. If you desire to use an MEL:
1. You should obtain a copy of the MMEL for your airplane. A copy of the MMEL can be obtained from the FAA’s Web site at http://fsims.faa.gov. If you do not have access to the internet, you can obtain a copy from your jurisdictional FSDO.
2. Section 125.201 authorizes flight with inoperative equipment under specific conditions.
3. An aviation safety inspector (ASI) may approve MELs for part 125 operators as part of the certification process.
4. You should submit your proposed MEL, as a separate document or as a section of your PPM, in your formal application for certification.
3.9.4 MEL Differences. Due to differences in operational factors (e.g., lack of maintenance bases), some options provided in the MMEL may not apply to part 125 certificate or A125 LODA holders. Each approved MEL will be tailored to the particular operator’s operations.
3.10 Maintenance Program.
3.10.1 Develop Maintenance Program. During your initial contacts with the FAA, and when developing the maintenance inspection program, you should follow the information provided in Chapter 9. It should be noted that a certificate holder under part 125 is not authorized by part 125 certification to perform preventive maintenance, rebuilding, or alteration. Such authority is not contained in part 43. This does not prevent an operator who holds a part 125 operating certificate from providing for its maintenance requirements by employing persons authorized to perform maintenance under part 43.
3-4
3.10.2 Airplane Requirements. Before submitting the formal application, you should assure that your airplane meet all applicable special airworthiness requirements in part 125 subpart E and all instrument and equipment requirements of part 125 subpart F for the operations proposed. Inoperative or unavailable equipment may be cause for denial of certification or place limitations on the proposed operations.
3.10.3 Qualified Personnel. You should also assure that adequate qualified personnel are available to perform your maintenance program, or agreements with other companies to perform this maintenance are satisfactory.
3.11 Airplane Required. Part 125 does not specifically require an applicant to own or have exclusive use of an airplane. Sections 125.27 and 125.31 require that a determination be made that you are properly equipped (refer to § 125.27(a)) and the registration number and airplane type be shown in your OpSpecs (refer to § 125.31(b)(2)). Essentially, this requires that a specific airplane which meets the requirements of part 125 for the operations shown in your OpSpecs be available at the time of certification. You may, however, request changes to the OpSpecs at any time after certification. The procedures for adding or deleting airplanes are discussed in Chapter 6.
3.12 Crewmembers.
3.12.1 Number of Qualified Crewmembers. You should review the requirements of § 125.263 through § 125.271 in light of your proposed operations and assure that you will have an adequate number of qualified crewmembers to conduct your proposed operations.
3.12.2 Crewmember Training. You are not required to have a formal training program; however, you should provide training for your crewmembers, or otherwise assure that they will be capable of successfully completing the testing requirements of §§ 125.287, 125.289, and
125.291. Section 125.296 permits crewmembers to complete training, testing, or checking in accordance with an approved training program that meets the requirements of part 125 and is conducted in accordance with an approved course conducted by a training center certificated under 14 CFR part 142. The regulatory responsibility for ensuring that an operator’s training program remains current and continues to meet the operator’s needs resides with the operator. Training, testing, and/or checking to be conducted by the training center will be authorized by the principal operations inspector (POI) via the Web-based Operations Safety System (WebOPSS) before any training is accomplished.
3.12.3 Contract Training Restrictions. If you elect to use a contract training provider, you are limited to the use of a part 142 certificated training facility (refer to § 125.296). The part 142 training facility must meet the simulator requirements of § 125.297. Use of a part 142 training facility to meet the crewmember requirements of part 125 must be approved by the POI through the appropriate WebOPSS paragraph. The training program should be reviewed and approved by the POI.
3.12.4 Review of Qualifications. Your crewmembers’ qualifications will be reviewed in light of their intended duties (refer to §§ 125.281, 125.283, and 125.285). These qualifications will be reviewed immediately prior to their oral and practical tests under part 125.
3-5
3.12.5 Crewmember Testing and Checking Requirements. Crewmembers must meet the testing and checking requirements of §§ 125.287, 125.289, and 125.291 prior to acting as a qualified crewmember for the company. All testing elements delineated in the rule are required. All testing must be conducted by a qualified ASI or authorized check pilot, and documented in accordance with the crewmember record requirements of § 125.401.
3.12.6 Pilot Proficiency Check. A pilot proficiency check conducted under 14 CFR part 121, § 121.441 that meets the checking requirements of part 121 appendix F may be accepted by the POI as meeting the requirements for operations conducted under part 125, under the following specified conditions:
1. The check is conducted in the same type of airplane, or in an airplane simulator or other training device, approved under § 125.297 for each flight maneuver or procedure to be accomplished during the proficiency check.
2. The pilot has passed a written or oral test on the appropriate provisions of 14 CFR parts 61, 91, and 125, and the OpSpecs and PPM of the certificate holder (refer to § 125.287(a)(1), (8), and (9)).
3. A properly documented record of that crewmember is maintained in accordance with the requirements of § 125.401.
4. If the POI elects to accept a § 121.441 check that meets the checking requirements of part 121 appendix F to satisfy the requirements for the proficiency check required under part 125, the requirements for items 2 and 3 above must be conducted by a part 125 company authorized check pilot. The discretion used by the POI to accept the part 121 appendix F check does not authorize the check pilot, who conducted the part 121 appendix F check, the authority to conduct the requirements specific to a part 125 operator (requirements of items 2 and 3 above).
3.12.7 Pilot Services for Multiple Part 125 Operators. Flightcrew members who meet the initial and recurrent pilot testing requirements or the pilot in command (PIC) instrument proficiency requirements of part 125 are permitted to make lateral moves between part 125 operators. For example, a pilot may provide services to more than one operator if the pilot meets the requirements of § 125.287(a)(1), (8), and (9) for each certificate holder. However, if a pilot fails to meet this requirement for one operator, that pilot may not provide the same services to any operator. Additionally, a failure of the required competency or proficiency check under part 125 requires notification of any part 121 or other part 125 operators who may employ the pilot. This can be accomplished by notifying the certificate-holding district offices (CHDO) of other operators that employ the pilot that failed the part 125 check.
3.13 Request for Check Pilot Authorization.
3.13.1 Issuing a Check Pilot Authorization. A check pilot authorization may be issued to an applicant for a part 125 certificate, an A125 LODA, an existing part 125 certificate holder, or existing A125 LODA holder. Although an individual is assigned check airman duties to conduct initial, recurrent, and instrument checks required by §§ 125.265(b),
3-6
125.285, 125.287, and 125.291, the authorization is issued to the applicant or operator planning to operate or operating under part 125.
3.13.2 Check Pilot Nominees. The FAA may authorize a company pilot to act as a check pilot for that company, or authorize a contract check airman from a part 142 training center, or authorize another part 125 check pilot as a check pilot for the company, to conduct the pilot testing and checking required by §§ 125.287 and 125.291 (refer to § 125.295).
These authorizations are issued when the FAA determines that a need exists based on factors such as the complexity of the operation (number of airplanes and flight personnel) and where the company can provide a qualified nominee. Requests for check airman authorizations should be submitted by letter to the jurisdictional FDSO. Further information on this subject can be found in Chapter 8.
3.13.3 Check Airman Scheduling. The operator should understand that the scheduling and use of a check airman is their responsibility. An operator entering into a multiple use arrangement may employ a check airman on a part time basis, may contract with another part 125 operator or part 142 training center to provide a check airman, or may contract directly with the check airman. However, each operator must ensure that the check airman maintains currency, as specified in the appropriate operating rule, and performs adequately when serving the operator.
3.13.4 Check Airman Approval for More Than One Operator. An operator seeking check airman approval for an individual already serving as a check airman for another operator must provide the same information to its POI as if the check pilot nominee was their company pilot. The operator’s POI must consider the means the company will use to train, qualify, and maintain the qualifications of the check airman candidate, and the required documentation. A check airman serving as a check airman for another operator may meet recurrent training requirements for more than one operator simultaneously. When the operator and the POI have agreed on the training and qualifications necessary for the check airman, serving as a check airman for another operator, the operator must submit a written letter of request to the POI.
3.13.5 Ensure Nominees Complete Training. Regardless, whether the check airman is a company pilot, contract check pilot from a part 142 training center, or a check pilot from another part 125 operator, the company requesting check airman authorization will ensure the check airman nominee completes all necessary training and checking. Once approved by the POI, the check airman will be approved, by a letter of authorization (LOA), to conduct checks for that operator.
Note: See Chapter 8, paragraphs 8.11–8.15 for additional information.
3.14 Administrative Resources. Adequate forms and manuals will need to be developed to properly document your company’s compliance with the applicable Federal aviation regulations and company procedures. During certification, the Certificate Management Team (CMT) will review these documents to assure that you have the necessary documentation and resources to begin operation.
3-7
3.15 List of Personnel. A list of the personnel who will be employed in management positions will be included in the PPM (refer to § 125.25(b)).
1. Each operator must show that they have enough management personnel, including at least a director of operations, to assure that its operations are conducted in accordance with the requirements of part 125.
2. The PPM will set forth the duties, responsibilities, and authority of each management personnel. This information will be placed in the PPM.
3. The names and addresses of each management position will be placed in the manual.
4. A person must be designated as the responsible person for the scheduling of inspections required by the manual and for the updating of the approved Weight and Balance (W&B) system on all of the operators airplanes.
5. The certificate holder will notify the FSDO of any changes made in the assignment of persons to the listed management positions within 10 calendar-days, excluding Saturdays, Sundays, and Federal holidays.
6. The FAA may deny an application for a certificate if it finds that any management person you intend to employ was previously employed in a similar position by a holder of a certificate under 14 CFR parts 121, 125, or 135 whose operating certificate was revoked, if that person’s employment or control contributed materially to the reasons for revoking that certificate (refer to § 125.27).
3.16 Preapplication Statement of Intent (PASI) and Formal Application Letter.
3.16.1 PASI. A potential applicant will submit a copy of the PASI (FAA Form 8400-6) after reviewing the appropriate regulations and advisory material and considering the personnel, facility, equipment, airplane, and document requirements for certification and operation.
3.16.2 Formal Application Letter. The formal application letter serves as the vehicle to transmit the package of documents required to complete the Formal Application Phase of the certification process. The inspector must inform the applicant that the formal application must be a letter containing a statement that the letter serves as a formal application for an operating certificate.
3.16.3 Application for Certification. The formal application for certification should be submitted as a letter, preferably on company letterhead.
3.16.4 Letter Content. This letter must contain:
1. A statement that you are applying for a certificate to conduct operations under part 125.
2. The full and official name of the applicant. This letter must be signed by the owner, when applying as an individual or sole proprietorship; all partners,
3-8 when applying as a partnership; or an authorized officer(s), when applying as an organization such as a company or a corporation.
3. A general outline of the areas where you intend to conduct flight operations.
The letter must contain the principal base of operation and/or principal place of business. The applicant must include their mailing address in the formal application letter, if it is different from his/her physical location address.
4. A reference to the compliance statement, referenced in Chapter 3, which outlines how you intend to meet the applicable sections of parts 91, 119, and
125.
5. The date you intend to begin flight operations under part 125.
3.17 Formal Application. The CMT ensures the formal application package represents a feasible proposal and is of sufficient quality to continue the certification process.
3.17.1 Application Quality. If the applicant has been thoroughly briefed and has acquired a thorough understanding of the requirements during the preapplication phase, the formal application should be of sufficient quality that any discrepancies can be resolved during the formal application meeting.
3.17.2 Rejected Formal Applications. Rejecting a formal application will be a sensitive issue since the applicant most likely will have expended considerable funds and resources to prepare it. Therefore, it is important for the Certificate Project Manager (CPM) to document thoroughly the reasons for rejection. The reasons must clearly indicate that to proceed with the certification process would not be productive. Reasons for rejection might include inadequate agreement on appropriate courses of action or evidence that the applicant has a serious lack of understanding of regulatory requirements and the certification process.
3.17.3 Formal Application Package. The formal application package should include:
• The formal application letter;
• A listing of management personnel and flightcrew members, including their résumés, certificates, and medicals;
• The compliance statement specifying how you propose to comply with each applicable section of part 91, 119, and 125;
• A copy of your Schedule of Events (SOE);
• A copy of the manuals required by §§ 125.71, 125.75, and 125.249;
• A copy of any deviation authority received; and
• A copy of any contracts or agreements with a person or persons who will perform required inspections or maintenance.
3-9
3.18 Foreign-Based Operators.
3.18.1 U.S. Citizen. If you are a U.S. citizen operating a U.S.-registered airplane applicable to part 125, you must comply with part 125 regardless of where your airplane is based or operated within the U.S., its commonwealth, territories, or possessions. If you are a U.S. citizen and your operation is entirely foreign based (i.e., you maintain your principal base of operations outside the United States, or conduct operations entirely outside of the United States), you will not be issued a part 125 operating certificate. Your application should be submitted to your jurisdictional FSDO or IFO, as applicable.
3.18.2 Non-U.S. Citizens Operating Outside the United States. If you are not a U.S. citizen and operate a U.S.-registered airplane subject to part 125 entirely outside the United States, its commonwealth, territories, or possessions, you need to only comply with the inspection programs and maintenance requirements of § 125.247. If the operator is foreign based, the inspection programs and maintenance required by § 125.247 would normally be approved by the applicable IFO prior to their use.
Note: A foreign-owned entity that operates U.S.-registered airplanes subject to part 125 entirely outside the U.S., its commonwealth, territories, or possessions will not be issued a part 125 operating certificate. They will only be required to comply with § 125.247.
3.18.3 Non-U.S. Citizens Operating Within the United States. If you are not a U.S. citizen and wish to operate a U.S.-registered airplane in any portion of the United States, its commonwealth, territories, or possessions, you must be certificated under part 125, or hold deviation authority under part 125. Your application should be submitted to your jurisdictional FSDO based on your U.S. base of operations/operator business address or if foreign based your applicable IFO.
3.19 Ready for the Inspection. Completion of the formal application package is considered to be an indication that your organization is ready for the Document Compliance Phase of the certification process.
4-1 CHAPTER 4. CERTIFICATION
4.1 Scope and Contents. This chapter outlines the usual sequence of events in the certification process.
4.2 Application Acknowledgment Letter.
4.2.1 Receipt of Application Acknowledgment. Upon receipt of your Preapplication Statement of Intent (PASI), the Flight Standards District Office (FSDO) will issue a letter acknowledging receipt. In addition, the letter will notify you if they have the resources to start processing your request.
4.2.2 Application Processing Notification. If the FSDO cannot start processing your request normally within 60 calendar-days, you will be notified. When the FSDO is able to begin processing your request, a subsequent letter will be sent notifying you that the FSDO can begin processing your request.
4.3 Inspection Team. The district office will normally assign a team of inspectors from operations, airworthiness, and avionics specialties. This team is commonly referred to as the Certificate Management Team (CMT). The CMT will have a Certification Project Manager (CPM) assigned; usually this will be the operations specialist but could be an airworthiness or avionics specialist. The CPM will normally be the point of contact (POC) between the CMT and the applicant. The CMT will assist you during the certification process, and answer your questions. They will review your submitted documents and perform the required inspections. You will be responsible for submitting documentation, and being ready for the necessary inspections in accordance with your submitted Schedule of Events (SOE). If you are unable to consistently meet your SOE, or are unable to complete the certification process, your certification will be terminated and you will be notified by letter. You can re-apply at any time after termination; however, your application will be processed in the order in which it is received, and you will have to start the certification process again, from the beginning, starting with the PASI.
4.4 Certification Procedures. This section provides the procedures for certificating a part 125 operator. The process allows interaction between the applicant and the FAA from initial inquiry to certificate issuance or denial. It ensures that programs, systems, and intended methods of compliance are thoroughly reviewed, evaluated, and tested. The certification process consists of the following five phases:
• Preapplication Phase,
• Formal Application Phase,
• Document Compliance Phase,
• Demonstration and Inspection Phase, and
• Certification Phase.
4-2
4.5 Preapplication Phase.
4.5.1 Review the Regulations and Requirements. The submission of FAA Form 8400-6, Preapplication Statement of Intent (PASI), indicates intent by the applicant to continue the certification process. It also allows the FAA to plan activities and commit resources.
Therefore, a potential applicant submits a copy of the PASI after reviewing the appropriate regulations and advisory material and considering the personnel, facility, equipment, airplane, and document requirements for certification and operation.
4.5.2 Proposed Certification Review. The FSDO manager uses the PASI to evaluate the complexity of the proposed certification, and if it is appropriate for the office to conduct the certification. The office manager ensures that trained and experienced inspectors are available for the certification.
4.5.3 FSDO Resources. The FSDO will gather and summarize the PASI information and start the Certification Service Oversight Process (CSOP), if office resources are available.
4.5.4 Preapplication Meeting. The CPM shall contact the applicant to arrange a preapplication meeting. The applicant is advised that key management personnel, as shown on the PASI, should attend the meeting and be prepared to discuss specific aspects of the applicant’s proposed operation. During the preapplication meeting, the CPM should ensure the applicant is informed about the certification process. The CPM will also discuss the form, content, and documents required for formal application.
4.5.5 Documents and Manuals. The CMT will furnish guidance and advice for the preparation of required documents and manuals. It is the responsibility of the applicant to produce acceptable documents and manuals.
4.5.6 Submitting Required Items. The applicant may submit required items in draft form before submitting the formal package. Whenever a problem or change occurs in the proposed operation, the applicant should notify the CPM immediately.
4.5.7 SOE Development. The applicant will need to develop an SOE. The SOE is intended to encourage you to submit material well in advance of the date operations are proposed to begin. If, however, the application is submitted with only the minimum lead time required by the regulation, complete documents (such as, the Policy and Procedures Manual (PPM)) may be required at the time of formal application. The SOE will contain the dates and the events, associated with those dates, when the CMT can expect documents and material from you, and when you will be ready for inspection and demonstration events. The SOE, when accepted, represents a commitment on the part of the applicant.
4.5.8 Sequence of Events. When developing the SOE, the applicant must remember the correct sequence of events. For example, airplane conformity inspections must be completed before emergency evacuation demonstrations begin.
4.5.9 Events and Activities. The number and types of events and activities that occur during certification vary according to the operation proposed. The SOE must include a complete
4-3 listing of each document to be submitted, activity to be performed, and item to be inspected.
4.5.10 Certification Delays or Termination. Failure to accomplish an item or event in a satisfactory or timely manner in accordance with the SOE could delay or terminate certification. In addition, if deficiencies are detected during the review of manuals or other documents, they will be returned for amendment or correction, which also may delay final certification.
4.5.11 Deviation Petition. If the applicant plans to petition for deviation, processing time must be considered in developing the SOE. Part 125, § 125.3 requires that a petition for deviation must be submitted to the appropriate FSDO at least 60 calendar-days before the date of intended operation.
4.5.12 Proposed Schedule. When reviewing the SOE, the team must carefully consider the feasibility of the proposed schedule with respect to logic of sequence, timeliness of events, completeness of events, and inspector availability.
4.6 Formal Application Phase. The Formal Application Phase is described in Chapter 3, paragraph 3.17. In addition to the information in paragraph 3.17, the applicant may want to have all of their documentation ready for review at the time of formal application.
Although not necessary, completion of most or all the documentation at the formal application meeting will reinforce, to the FSDO, the applicants willingness and commitment to see the certification process through to certification.
4.7 Document Compliance Phase.
4.7.1 Document Review. In the Document Compliance Phase, the applicant’s compliance statement, manuals and other documents are thoroughly reviewed for compliance with applicable regulations and for conformity with safe operating practices. After review by the CMT, each document is accepted or approved, as applicable, or rejected.
4.7.2 Operations Specifications (OpSpecs). OpSpecs outline the specific operations which a part 125 certificate holder is allowed to conduct and any deviations the certificate holder has been granted. They also supplement the operating rules and contain limitations not addressed in the regulations. Often the regulations require that certain authorizations and limitations be written in the OpSpecs. For example, § 125.363(d) states that the minimum requirements for over water operations will be indicated in the OpSpecs. This could include additional requirements for emergency equipment or personnel required for that particular operation but not indicated in the regulation.
4.7.3 The Policy and Procedures Manual (PPM). Section 125.71 requires a part 125 air operator to prepare and keep current a manual which describes the operator’s procedures and policies. The manual is for use by all of the operator’s personnel and also indicates to the FAA how the operator intends to conduct its operation. The manual’s complexity depends upon the complexity of the operation. As a general rule, if the applicant submits the formal application only 60 calendar-days before operations are scheduled to begin
4-4 and draft documents were not previously submitted, the team may require that additional manual material be submitted at the time of formal application.
4.7.3.1 The CMT will review the company PPM to determine that it:
1. Contains adequate procedures and policies concerning all items listed in §§ 125.73 and 125.249, and similar information relating to §§ 125.401, 125.403, 125.405, 125.407, 125.409, and 125.411.
2. Contains any other procedures and policies necessary to meet any unique operations conducted by the company or authorized by the OpSpecs.
3. Does not contain procedures or policies contrary to the applicable CFRs or OpSpecs.
4.7.3.2 The operator will maintain a copy of this manual at their principal operations base (refer to § 125.7l (b)) and make copies available to ground and maintenance personnel and furnish copies to flightcrew members as outlined in § 125.7l (d).
4.7.3.3 Manuals not acceptable to the certification team will be returned to the applicant for revision and/or correction with a letter stating what the CMT found as unacceptable.
4.7.4 Management Positions. The position of Director of Operations (DO) is the only management position specified by § 125.25. The chief pilot’s position is only a suggested position. Additionally, § 125.25 states that management personnel be enough “to assure that its operations are conducted in accordance with the requirements of part 125”. The applicant may elect not to have any management positions other than director of operations, or the applicant may have more positions. In that case, qualifications are up to the judgment of the certification team, based on the type of management position and the complexity of the operation.
4.7.5 Acceptable Weight and Balance (W&B) Procedures. Acceptable W&B procedures may be found in the current edition of Advisory Circular (AC) 120-27, Aircraft Weight and Balance Control. Material from this publication, can be cited as a resource and adapted to the applicant or operator’s procedures, but reference to these publications as a means of compliance is not acceptable. Certain W&B procedures described in AC 120-27 require authorization.
4.7.6 Hazardous Materials (Hazmat) Program. Although a training program is not required by part 125, the operator should be encouraged to prepare a hazmat program for all flightcrew members and ground personnel. Whether or not an operator elects to transport hazmat, the company manual required by § 125.73 must include certain procedures and instructions relating to hazmat. Some form of training in this area should be addressed.
There are numerous all-cargo operators, with approved hazmat training programs, who could be contracted with to provide initial and recurrent training. (The inspector might consider keeping a current list of such operators as a resource.) If the operator uses a