11 July 72 AC 20-78 CHAPTER 10. MAINTENANCE INFORMATION DC-8 AIRCRAFT MAINTENANCE INFORMATION. The following is & listing of selected significant maintenance difficulties that have been reported by air carriers as mechanical reliability reports from 1970 and 1971 records. This information may be useful in identifying additional structural inspection problem areas. In all cases, check the corresponding trouble area, left right, top bottom, forward aft,etc.
Wing:
During routine inspection a l2" crack was found in the upper R/W skin at W/S Xrs 367. The total time on the aircraft was 30,358 hours. The operators report referred to this as being a corrosion type crack.
During overhaul a 6-inch crack was found in the L/W bulkhead upper cap fitting P/N 5615314-1 at W/S Xrs 508.
The crack was adjacent to the center spar along the bulkhead cap fitting radius. The aircraft total time 38,513 hours.
(3) Routine inspection disclosed a 2-inch crack in the L/W leading edge lower skin P/N 5754700-3 above #2 pylon and a one-inch crack above #3 pylon. A 4-inch crack was also found in the R/W leading edge skin P/N 5754701-3 above #4 pylon. (Reference marufacturer's All Operator Letter (AOL) 8-490 dated 10/28/70.)
(4) Routine inspection disclosed a 2-inch crack in L/W front spar upper splice angle at W/S Xps 63, and an 11-inch crack in the R/w front spar forward cap progressing 1/B from W/S Afs 67.5. Aircrait total time 31,992 hours.
(5) During overhaul found a 4-inch crack in L/W stringer #8 The crack was located along the radius formed by the vertical and 'Y" legs of the splice. Aircraft total time was 34,888 hours.
During overhaul a 2 3/4-inch crack was detected in the L/W lower front spar cap at W/S Xrs 67.5. The crack originated at an attach hole and progressed through two other attach holes. Aircraft total time 17,902 hours.
During approach the aircraft had a tendency to roll with wing flaps extended beyond 25° accompanied by a split flap indication. Inspection after landing disclosed a broken compensator link and shaft, P/N 2647101. Aircraft time since overhaul 1,048 hours.
Chap 10 Par 32 Page 27
AC 20-78 11 July 72
(8) During inspection an 8-inch crack was found in the R/W flap support fitting, P/N 5614374-2, at W/S Xys 219. The aircraft total time was 34,261 hours.
During overhaul a 3-inch crack was found in the L/W support fitting, P/N 5614374-1 at W/S Xrs 219. Total aircraft time was 17,700 hours.
(10) During overhaul a 5-inch crack was found in the radius of attach bracket, P/N 3653812-3 located between the I/B support bearing and the R/H 0/B aileron. Total aircraft time 34,345 hours, time since overhaul 10,613 hours.
(11) Routine inspection disclosed broken mount lugs on the I/H I/B flap actuating cylinder, P/N 5642074-5015. Time since overhaul was 10,915 hours. Operators report attributed breakage to stress corrosion.
(12) One aircraft was taken out of scheduled service and ferried to a maintenance base due to finding broken I/H O/B flap hinge base fittings P/N's 5653754-1 and 5653755-1 at station 219.
Total aircraft time 37,788 hours, time since last service check was 329 hours. Another operator reported a 4-inch crack in the R/H 0/B flap hinge base at station 219. Aircrait total time was 37,640 hours.
Routine inspection revealed partial separation of the L/W flap follow-up cable at W/S Xps 22.750. Cable P/N 5652981-529, total aircraft time l1,346 hours. Operators report attributed separation to be a result of oxidation.
(14) Routine inspection disclosed a cracked R/H O/B flap hinge base fitting at station 339. Total aircraft time was 37,867 hours.
(15) During scheduled inspection an Il-inch crack was found in the crank arm of the R/H wing I/B slot torque tube.
(16) During routine inspection the L/H wing flap drive link, P/N 5655655-501, was found cracked at station 219. Total time since new was 23,145 hours.
During scheduled inspection the R/H flap support bracket, P/N 5614376-2, was found to have a crack approximately 10 inches in length. Total aircraft time was 35,170 hours.
(18) A flight returned due to loss of hydraulic fluid. Inspection after landing disclosed a crack in the R/H aileron actuating cylinder, P/N 5613697-5. The crack was along the circumference of the cylinder barrel.
Chap 10 Page 28 Par 32
11 July 72 AC 20-78
b. Lylon.
(1) Routine inspection disclosed a 12-inch crack in #4 pylon upper 1/B skin at station Yop 230-240. Total aircraft time was 10,419 hours.
During overhaul, angle P/N 5769515-36 and doubler P/N 5769515-155 were found cracked on the I/B side of #3 pylon.
Total aircraft time 10,524 hours.
During routine inspection a chordwise crack was found in # pylon intercostal P/N 5769523-46. The crack was in the horizontal leg and located 1-inch 0/B of the pylon upper 0/B spar plane. Total aircraft time was 8,091 hours.
Routine inspection disclosed the lower spar I/B cap broken in two in #l pylon. The break occurred 12 inches from the found inh crane or spar web at top 248 and 248 and those creast ofted silar ascerpentes 41 pou two skin cracks at I 32,156 hours.
at Yop 243 with a total aircraft time of 30,141 hours.
(5) Inspection found a crack in the vertical leg of the o/B spar cap at station Yop 220 of #1 pylon.
(6) Routine inspection disclosed a cracked top 0/B spar rail at shit in 44 Bylon. Total aircraft time was 34,510 hours. and a 2-inch crack in the web at station Yor A 5-inch crack was found in the 0/B skin of #1 pylon at station Yop 235. Total aircraft time was 8,505 hours.
C. Landing Gear.
(1) During taxi after landing #3 wheel, P/N 152059, failed at the I/B rim, operator reported a total of 2,297 landings. Another operator reported #3 wheel failure during takeoff, total landings since overhaul was 63. Failure was attributed to cracks which originated at corrosion pits.
A flight was interrupted due to inability to retract the MIG after takeoff. Inspection after landing disclosed the L/H MIG down lock bungee cylinder piston rod broken, P/N 4641900.
During walkaround inspection found R/H MG bogie beam broken at the lover swivel lug, P/N 5774700. Operator attributed failure to corrosion due to lack of grease penetration and initiated a program of inspection and modification to reduce possibility of additional failures. A similar condition was also found on the L/H bogie beam of another aircraft.
chap 10 Par 32 Page 29
AC 20- 78 11 July 72
(4) A flight returned due to NIG not retracting, inspection found the NIG side brace broken at the retract strut attach lugs, side brace P/N 5771405-5. Total aircraft time 21,030 hours.
Several operators have reported flight interruptions due to left and right MIG retract cylinder attach pins being broken.
These reports showed that the first evidence of malfunction usually an unsafe gear position indication.
(6) Routine inspection disclosed a cracked L/H MIG bungee cylinder attach casting, P/N 5719176-5511.
Flight crew reported a severe jolt when the landing gear was extended and did not get a dom and locked indication. The aircraft was stopped on the runway and inspection showed the L/H MIG was not locked due to broken retract and bungee cylinders.
A flight was interrupted due to a loud roar and vibration when gear was retracted after takeoff, fuel was jettisoned and the aircraft returned. Inspection revealed a broken NIG door link, ₽/N 5646507-501. Total aircraft time was 11,830
(9) One operator reported finding a broken O/B brake link rod on the R/H MG, rod P/N 576390. Total time on rod 10,359 hours.
During routine brake change, #7 brake carrier lug was found broken off. A total of 225 landings had been made since last brake overhaul.
(11) After takeoff,. the left MIG could not be retracted.
Inspection after landing revealed a broken I/B bungee unlock bracket, P/N 6F-8574-501, which prevented the gear from being inlocked from the down position. Total aircrait time was 38,107 hours.
(12) The #4 wheel broke on landing on one aircrait, wheel f/N 1>42>1-1. There had been 100 landings accumulated since the last overhaul.
A flight returned due to the landing-gear warning light remaining on after gear was retracted. Inspection found a broken pivot lock arm, P/N 5769871-1, on the left MIG. Total aircraft time was 21,220 hours.
(14) During scheduled inspection, the R/H MIG forward bogie beam was found cracked at the upper attach lug for the pivot unlock arm. Total aircraft time was 28,269 hours.
Chap 10 Page 30 Par 32
11 July 72 AC 20-78
d. Fuselage.
During inspection found severe corrosion on the inner surface of the aft center section lower skin panel P/N 5615372-3, F/S 1150-1290. Also found four cracks 1/2" to 4" in length and light corrosion on longerons and doublers.
Total aircraft time was 30,963 hours, time since overhaul 1,801 hours.
Routine inspection disclosed a 4-inch crack in the upper aft corner of the rear passenger door jamb skin. Total aircraft time 37,221 hours.
(3) During scheduled inspection cracks were found in the fittings at the top of the pressure bulkhead at F/S 857 in the left and right wheel wells, fitting P/N's 3646874-1 and -2. Total aircraft time 7,771 hours.
Several operators reporting finding cracks in fuselage former #24, L/H side at F/S 920 and 980, cracks ranged from 2 to 4 inches in length. Total aircraft time ranged from 7,771 hours to 33,091 hours.
During overhaul, a 22-inch crack in the 0/B flange radius of the L/H MIG support fitting web, support P/N 5750092-501.
Repairs were made in accordance with SB 63-61.
(6) Several occurrences of excessive corrosion have been reported on metal floorboards in the forward gally, center aisle opposite forward galley, and in the mid-lavatory areas.
Total aircraft time ranged from 8,027 hours to 11,075 hours.
(7) Moderate corrosion was found during routine inspection at the following locations on the fuselage skin between stringers 34L and 34R; F/S 640 to 650, F/S 1075 to 1260, F/S 1300 to 1300, and F/S 1430 to 1480. Total aircraft time was 32,135 hours.
Routine inspection revealed bulged skin and rivets popped at the following locations: F/S 1100, stringer #36 F/S 1300 at stringer #29, F/S 1420, 1440, 1460, and 1240 at 1400, and 1490 at stringers 27 through 31 right. Total aircraft time was 37,399 hours.
(9) Scheduled inspection disclosed corrosion of lower fuselage skin adjacent to fasteners and doublers at F/S 420 to 500 and F/S 1180 to 1300 between stringers 33R and 351. Total aircraft time was 34,510 hours.
Chap 10 Par 32 Page 31
AC 20- 78 11 July 72
(10) During routine inspection corrosion was found in the lower aft corner of the forward service door jamb and skin laps.
Total aircraft time was 34,510 hours.
e. Miscellaneous.
(1) An attempt to dump fuel in flight failed. Inspection after landing disclosed a bent I/H dump chute link rod, P/N 3765140.
The first officer's windshield outer panel shattered during flight on one aircraft. The aircraft was at 28,000 feet with windshield heat in warm position.
(3) During routine inspection, two 5-inch cracks were found in the rudder fiberglas section at station Zy 253.0.
Chap 10 Page 32 Par 32
11 July 72 AC 20-78 Appendix 1
STATIONS DESCRIPTION. The airplane is divided into reference points in inches, designated as station numbers. These station numbers provide a means for quickly identifying the location of components, the center of gravity, and the distribution of weight. There are three axes used in the plotting of station numbers: The lateral or X-axis, the longitudinal or I-axis, and the vertical or Z-axis.
a. Glossary of Terms.
(1) FRP The fuselage reference plane is used as a basic reference. It extends along the fuselage cusps which are formed by the intersection of the upper and lower sections of the fuselage. The reference plane has an angle of one degree nose down with reference to the ground and is the origin of Z-stations.
(2) WRP The wing reference plane contains the trailing edge of the wing and has an angle of dihedral of 6-1/2 degrees to the FRP.
(3) VRP The vertical reference plane (plane of symmetry) bisects the airplane through its centerline at an angle of 90 degrees to the FRP.
(4) X-axis Divided into segments in inches along the lateral plane.
(5) Y-axis Divided into segments in inches along the longitudinal plane. There is a I-axis subsystem designation for all subsystems.
(6) Z-axis Divided into segments in inches along the vertical plane.
b. Wing Subsystem Designations.
MOX (I) B62: This subsystem designation refers to the center, or constant, section of the wing. It consists of stations in inches, parallel to the centerline of the airplane and extending outboard 69.5 inches from its origin at the airplane centerline to its 7x (8) This wing subsystem designation denotes stations in inches, parallel to the centerline of the airplane and perpendicular to the WRP, beginning at the dihedral break and extending outboard indefinitely.
AC 20-78 11 July 72 Appendix l
(3) Xp This designation represents stations in inches, located perpendicular to the wing flap hinge line.
(4) Xes This designation is both a wing and a horizontal stabilizer station numbering subsystem, representing stations in inches located perpendicular to their front spars. In the wing, the point of C• Horizontal Stabilizer Subsystem Designations.
(1) Xe This designation refers to stations in inches, located perpendicular to the elevator hinge line.
(2) Xet This subsystem designation represents stations in inches, located perpendicular to the elevator tab hinge line.
(3) XIS This designation represents stations in inches, located perpendicular to the front spar. The point of origin is the centerline of the fuselage.
(4) X1 This subsystem designation represents the stations in the horizontal stabilizer system. The subsystem's point of origin is at the fuselage centerline.
d. Vertical Stabilizer Subsystem Designations.
(1) Zoy This subsystem designation denotes the stations in the vertical stabilizer system. Its origin is located 47 inches above the FRP at fuselage station 1464.2. The stations in this subsystem are segments divided into inches, parallel to the FRP.
(2) Zes This designation represents stations in inches along the center spar of the vertical stabilizer.
The stations are located perpendicular to the center spar and originate at Zy.
(3) Lfs This subsystem designation represents the front spar system of the vertical stabilizer. It consists of stations divided into inches, located perpendicular to the front spar and originating
(4) ZIe This subsystem designation represents stations in inches, along and parallel to the leading edge of the vertical stabilizer, originating at Zy, Page 2 Par 1
11 July 72 AC 20-78 Appendix 1
(5) Ly This subsystem designation refers to the rudder system of the vertical stabilizer. It consists of stations divided into inches, located perpendicular to the rudder hinge line and originating at Zy.
(6) Irs This subsystem designation refers to the rear spar system of the vertical stabilizer. It consists of stations divided into inches, located perpendicular to the rear spar and originating at Zy.
(7) Zat This designation represents the rudder tab hinge system of the vertical stabilizer. It consists of stations divided into inches, located perpendicular to the hinge line of the rudder tab, and originating at Zy.
Par 1 Page 3
11 July 72 AC 20- 78 Appendix 2 142'4"
FUSELAGE REFERENCE PLANE 12'3" 10° 30° 2'6".
20'10"
PIVOT AXIS x = 125.0 STATIC GROUND PLANE Y = 921.0 Z =-41.1 150'8" RUDDER →6'3" RIGHT 32 1/2° LEFT 32 1/2° 29'10" 42'4" 137 4'5" 1Ґ з" 415"11" 57'6"
PIVOT AXIS Х =Ô FUSELAGE REFERENCE PLANE Y=240.0 Z=-50.I STATIC GROUND PLANE
HORIZONTAL GROUND REFERENCE PLANE Fig. l Basic Dimensions Page 1
AC 20-78 11 July 72 Appendix 2 265 1517 1400 123 718 798 0000 1 1661 40 285 LOWER FUSELAGE CONSTANT 1420| 1601 1795 360 SECTION 1180 1490 1310 360
CABIN CONSTANT SECTION oooo oo..aoo.....a. • 0 1220 1100 855.5 683.0 540 374.6 1355 (CENT ERWING (CENTERWING 412.7
REAR SPAR) FRONT SPAR)
781.7 ( CENTERWING
CENTER SPAR) Fig. 2. Fuselage Station Charts Page 2