APPENDICES
Appendix Number Figure Number Title Page Number
APPENDIX 1 Power Available A1-1
Figure A1-1 Brake Horsepower Versus Pressure Altitude A1-5 Figure A1-2 Turbocharged Brake Horsepower Versus Altitude A1-7
APPENDIX 2 Climb Data Reduction A2-1
Figure A2-1 Coefficient of Drag Versus Coefficient of Lift A2-3
APPENDIX 3 Minimum Control Speed Extrapolation to Sea Level A3-1
Table A3-1 Flight Test Data A3-3 Table A3-2 Tabulated Thrust Horsepower Available A3-5 Figure A3-1 Thrust Horsepower at Sea Level A3-5
APPENDIX 4 FAR 23 Manuals, Markings and Placards Checklist A4-1
APPENDIX 5 Guide for Preparing Airplane Flight Manual and Pilot’s Operating Handbook Supplements A5-1
APPENDIX 6 Sample Kinds of Operating Equipment List A6-1
APPENDIX 7 Useful Information A7-11
Figure A7-1 U.S. Standard Atmosphere A7-3 Figure A7-2 Temperature Conversion Chart A7-7 Figure A7-3 Determination of Air Temperature in A7-9 Relation to International Standard Atmosphere Figure A7-4 Density/Pressure Altitude Conversion A7-11 Figure A7-5 Compressibility Correction to CAS A7-13 Figure A7-6 Altimeter Error vs. CAS A7-15 Figure A7-7 Temperature Ram Rise A7-17 Figure A7-8 Stall Speed at Bank Angle A7-19 Figure A7-9 Vertical Acceleration Versus Angle of Bank A7-21 Figure A7-10 Flight Path Velocity - Knots (TAS) A7-23
x
Appendix Number Figure Number Title Page Number
Figure A7-11 Takeoff and Landing Crosswind Component
- Knots A7-27
APPENDIX 8 Conversion Factors Table A8-1
APPENDIX 9 Airspeed Calibrations A9-1
Figure A9-1 Error Analysis of Ground Course Method A9-3
Figure A9-2 Ground Airspeed Calibration A9-4 Table A9-1 Sample Speed Course Data and Data Reduction A9-11 Figure A9-3 Sketches of Trailing Static Bomb & the Trailing Static Cone A9-5 Figure A9-4 Typical Position Error Correction Data for an Aircraft A9-6 Figure A9-5 Typical Position Error Corrections Data for an Aircraft A9-7 Figure A9-6 Tower Fly-By Method A9-16 Figure A9-7 Trapped Static Source Schematic A9-21 Table A9-2 Trapped Static Data Reduction A9-23 Figure A9-8 Ground Airspeed Calibration A9-27 Table A9-3 Sample Ground Airspeed Calibration Using a Distance Measuring Unit A9-31
APPENDIX 10 Guide for Determining Climb A10-1 Performance after STC Modifications
xi
ILLUSTRATIONS
The first block of digits in the figure number denotes the associated paragraph number. The second block of digits denotes the figure number within the paragraph.
Figure Number Title Page Number
17-1 Stall Speed 16 17-2 Propeller Coefficients 18 17-3 Zero Thrust 18 21-1 Accelerate-Stop Time Delays 32 23-1 Takeoff Distance - Critical Engine Failure Recognized at V1 40 23-2 Takeoff Distance All Engines Operating 40 23-3 Takeoff Run - Critical Engine Failure Recognized at V1 41 23-4 Takeoff Run - All Engines Operating 41 23-5 Clearway Profiles 42 24-1 Takeoff Segments and Nomenclature 43 24-2 Net Takeoff Flight Path 44 25-1 Observed Data 46 25-2 Rate of Climb vs. Airspeed 47 26-1 Rate of Climb and Speeds 48 27-1 Landing Time Delays 55 51-1 Stick Force Per G 70 70-1 Static Longitudinal Stability Data 73 70-2 Low Speed Instabilities; Normal, Utility, and Acrobatic Airplanes 74 70-3 Low Speed Instabilities; Commuter Airplanes 74 71-1 Static Longitudinal Stability Data over Complete Speed Range 75 72-1 Static Longitudinal Stability Plot (Cruise Condition) 77 100-1 Spin Evaluation Configuration Matrix 93 256-1 Carburetor Air Heat Rise Calculations 125 256-2 Carburetor Air Heat Rise Plots 126
TABLES
The first block of digits in the table number denotes the associated paragraph number. The second block of digits denotes the table number within the paragraph.
Table Number Title Page Number
6-1 Tolerances 3 6-2 Corrections to Standard Value Parameter 3 6-3 Sample Portion of Airspeed Indicator Calibration 5 27-1 WAT Chart 49 51-1 Procedures 69 166-1 Sample of CO-concentration Matrix 107 287-1 Light Duration 131
xii
ADVISORY CIRCULARS Advisory Circular Paragraph Number Title Number
23-7 Substantiation for an Increase in Maximum Weight, Maximum Landing Weight, or Zero Fuel Weight 8a(2) 91-23A Pilot’s Weight and Balance Handbook 9b
23.629-1A Means of Compliance with Section
23.629, “Flutter” 132 23-17 Systems and Equipment Guide for Certification of Part 23 Airplanes
20.118A Emergency Evacuation Demonstration 164 23-16 Powerplant Guide for Certification of Part 23 Airplanes 20-124 Water Ingestion Testing for Turbine Powered Airplanes 255 20-67B Airborne VHF Communications Equipment Installations 287B(1) 25-4 Inertial Navigation systems (INS) 287b(12)(i) 121-13 Self-Contained Navigation Systems 287b(12)(i) (Long Range) 287b(13)(i) 90-79 Recommended Practices and Procedures for the Use of Electronic Long-Range Navigation Equipment 287b(16) 20-121 Airworthiness Approval of Airborne Loran-C Systems for Use in the U.S.
National Airspace System 287b(17) Fuel-Injection, Reciprocating Engines 290c xiii
Advisory Circular Paragraph Number Title Number
23.1419-1 Certification of Small 48b(5) Airplanes for Flight in 337 Icing Conditions 339
20-88A Guidelines on Marking of Aircraft 387c Powerplant Instruments (Displays) 388 20-129 Airworthiness Approval of Vertical Navigation (VNAV) Systems for Use in the U.S. National Airspace System (NAS) and Alaska 20-130A Airworthiness Approval of Navigation or Flight Management Systems Integrating Multiple Navigation Sensors 20-138 Airworthiness Approval of Global Positioning System Navigation Equipment For Use as a VFR and IFR Supplemental Navigation System
23.1309-1C Equipment, Systems, and Installations in 21c(1) Part 23 Airplanes
23.1311-1A Installation of Electronic Displays in Part 23 Airplanes 90-96 Approval of U.S. Operators and Aircraft 287b(11)(i) to Operate Under Instrument Flight Rules (IFR) in European Airspace Designated for Basic Area Navigation (BRNAV/RNP-5) 91-49 General Aviation Procedures for Flight in North Atlantic Minimum Navigation Performance Specifications Airspace xiv
CHAPTER 1. GENERAL
1. SECTION 23.1 APPLICABILITY.
a. Explanation.
(1) Airplane Categories. Section 23.1(a) is introductory and prescribes the airplane categories eligible for certification under 14 CFR Part 23 . Applicants should refer to 14 CFR Part 21 for certification procedures.
(2) Design Data. Section 23.1(b) requires an applicant to demonstrate compliance by some acceptable means even though the FAA has previously certificated an identical alteration for someone else and has the supporting data on file. Design data submitted with an application for certification is not releasable to the public or any other applicant without the consent of the data holder.
b. Procedures. None.
2. SECTION 23.3 AIRPLANE CATEGORIES.
a. Explanation. For Normal/Utility Category as well as for Commuter Category airplanes, stalls (except whip stalls) are approved maneuvers. In this context, approved stalls are to be understood to be stalls as defined in §§ 23.49, 23.201, and 23.203.
b. Procedures. None.
3.-5 RESERVED.
CHAPTER 2. FLIGHT Section 1. GENERAL
6. SECTION 23.21 PROOF OF COMPLIANCE.
a. Explanation.
(1) Determining Compliance. This section provides a degree of latitude for the FAA test team in selecting the combination of tests or inspections required to demonstrate compliance with the regulations. Engineering tests are designed to investigate the overall capabilities and characteristics of the airplane throughout its operating envelope and should include sufficient combinations of weight, center of gravity, altitude, temperature, airspeed, and so forth, necessary to define the envelope and show compliance within. Testing should be sufficiently rigorous to define the limits of the entire operating envelope and establish compliance with the regulations at these points. If compliance cannot be established between these points, additional testing should be conducted to determine compliance. Testing should confirm normal and emergency procedures, performance information, and operating limitations that are to be included in the Airplane Flight Manual (AFM).
(2) Flight Tests. Section 21.35 requires, in part, that the applicant make flight tests and report the results of the flight tests prior to official FAA Type Inspection Authorization testing. After the applicant has submitted sufficient data to the FAA showing that compliance can be met, the FAA will conduct any inspections, flight, or ground tests required to verify the applicant's test results. Compliance may be based on the applicant's engineering data and a spot check or validation through FAA flight tests. The FAA testing should obtain validation at critical combinations of proposed flight variables if compliance cannot be established using engineering judgment from the combinations investigated.
(3) Use of Ballast. Ballast may be carried during the flight tests whenever it is necessary to achieve a specific weight and center of gravity (c.g.) location. Consideration should be given to the vertical as well as horizontal location of the ballast in cases where it may have an appreciable effect on the flying qualities of the airplane. The strength of the supporting structures should be considered to preclude their failure as a result of the anticipated loads that may be imposed during the particular tests.
(4) Flight Test Tolerances. The purpose of the tolerances specified in § 23.21(b) is to allow for variations in flight test values from which data are acceptable for reduction to the value desired. They are not intended for routine test scheduling at the lower weights, or to allow for compliance to be shown at less than the critical condition; nor are they to be considered as allowable inaccuracy of measurement (such as in an airspeed calibration). Where variation in the parameter on which a tolerance is allowed will have an effect on the results of the test, the result should be corrected to the most critical value of that parameter within the operating envelope being approved. If such a correction is impossible or impractical, the average test conditions should assure that the measured characteristics represent the actual critical value.
(5) Following are additional tolerances that are acceptable:
Item Tolerance Airspeed 3 knots or ±3%, whichever is greater Power ±5% Wind (takeoff and, landing tests) As low as possible, but not to exceed approximately 12% VS1 or 10 knots, whichever is lower, along the runway measured at a height of 6 feet above the runway surface. At higher wind velocities, the data may be unreliable due to wind variations and unsmooth flight conditions.
TABLE 6-1 - Tolerances
(6) The following list indicates cases in which corrections to a standard value of the parameter are normally allowed:
Test Weight Density Power Airspeed Other Takeoff Performance X X X X Wind, runway gradient Landing Performance X X — X Wind, runway gradient Stall Speed X — — — Climb Performance X X X X Acceleration VMC — X X —
TABLE 6-2 - Corrections to Standard Value Parameter
(7) Function and Reliability Test. Section 21.35(b)(2) specifies the requirements of Function and Reliability Tests, which are required for aircraft with a maximum certificated weight over 6,000 pounds (lbs) (2730 kilograms (kg)).
b. Procedures.
(1) Test Plan. Efforts should begin early in the certification program to provide assistance to the applicant to ensure coverage of all certification requirements. The applicant should develop a test plan that includes the required instrumentation.
(2) Instrument Calibration. Test instrumentation (transducers, indicators, and so forth) should be calibrated (removed from the airplane and bench checked by an approved method in an approved facility) within 6 months of the tests. When electronic recording devices are used, such as oscillographs, data loggers, and other electronic data acquisition devices, preflight and post-flight parameter recalibrations should be run for each test flight to ensure that none of the parameters have shifted from their initial zero settings. Critical transducers 3
and indicators for critical tests (for example, airspeed indicators and pressure transducers for flight tests to VD) should be calibrated within 60 days of the test in addition to the other requirements mentioned above. The instrument hysteresis should be known; therefore, readings at suitable increments should be taken in both increasing and decreasing directions.
Calibration records, like the one shown below, should be signed by the agent of the repair or overhaul facility doing the work and be available to the test pilot prior to beginning test flying. It should be emphasized that these calibrations must be accomplished at an approved facility. For example, using a leak checker to "calibrate" an airspeed indicator, whether in or out of the airplane, is not acceptable.
SAMPLE PORTION OF AIRSPEED INDICATOR CALIBRATION XYZ INSTRUMENT SERVICE, INC.
ABC CITY AIRPORT APPROVED REPAIR STATION - NO. 1234 8/12/80 P/N 1701DX8-04 S/N AF55-17044
A/S Indicator KNOTS
Master Test
Ascent Indicator Reads
Descent Indicator Reads 40 38.0 39.0 50 49.0 50.5 60 59.5 61.0 70 70.0 71.0 80 80.0 81.0
TABLE 6-3 - Sample Portion of Airspeed Indicator Calibration
(3) Use of Ballast.
(i) Loading. Ballast loading of the airplane can be accomplished several ways to achieve a specific weight and c.g. location as long as the loading remains within the physical confines of the airplane. In flight test work, loading problems will occasionally be encountered, making it difficult to obtain the desired c.g. location. Those cases may require loading in engine compartments or other places not designed for load carrying.
When this condition is encountered, care should be taken to ensure that local structural 4
stresses are not exceeded or that airplane flight characteristics are not changed due to changes in moments of inertia caused by adding a very long arm (tail post, and so forth).
(ii) Solid and Liquid Ballast. There are basically two types of ballast that may be used in airplane loading: solid or liquid. The solids are usually high-density materials such as lead or sandbags, while the liquid is usually water. In critical tests, the ballast should be loaded in a manner so that disposal in flight can be accomplished and be located at a point that will produce a significant c.g. shift forward when jettison takes place. In any case, the load should be securely attached in its loaded position. In airplanes with multiple fuel tank arrangements, the fuel load and distribution should be considered for weight and c.g. control.
(4) Function and Reliability Tests for Airplanes over 6,000 lbs. Maximum Certificated Weight.
(i) A comprehensive and systematic check of all aircraft components must be made to assure that they perform their intended function and are reliable.
(ii) Function and reliability (F&R) testing must be accomplished on an aircraft that is in conformity with the approved production configuration. F&R testing should follow the type certification testing to assure that significant changes resulting from type certification tests can be incorporated on the aircraft prior to F&R tests.
(iii) All components of the aircraft should be periodically operated in sequences and combinations likely to occur in service. Ground inspection should be made at appropriate intervals to identify potential failure conditions; however, no special maintenance beyond that described in the Aircraft Maintenance Manual should be allowed.
(iv) A complete record of defects and failures should be maintained along with required servicing of aircraft fluid levels. Results of this record should be consistent with inspection and servicing information provided in the Aircraft Maintenance Manual.
(v) A certain portion of the F&R test program may emphasize systems, operational conditions, or environments found particularly marginal during type certification tests.
7. SECTION 23.23 LOAD DISTRIBUTION LIMITS.
a. Explanation.
(1) C.G. Envelope. The test tolerance of ±7% of the total c.g. range (given in § 23.21) is intended to allow some practical relief for in-flight c.g. movement. This relief is only acceptable when the test data general scatter is on either side of the limiting c.g. or when c.g.
correction from test c.g. to limit c.g. is acceptable. Sufficient points inside the desired weight and balance envelope should be explored to ensure that the operational pilot will not be placed in an unsafe condition. Should unsatisfactory flight characteristics be present, the limits of the envelope should be reduced to ensure safe margins. Where variation in the c.g.
position may have a significant effect on the result of a test (for example, spins and VMC), the result should be corrected to the most critical c.g. position within the operating limits to be 5
approved. If such a correction is impractical or may be unreliable, the actual test should ensure that the measured characteristics represent the critical value.
(2) Narrow Utility C.G. Envelope. Some utility category airplanes, for which spin approval is sought, may have a very narrow c.g. range. If a limited fuel load is required to achieve the narrow c.g. envelope, the test pilot should ensure that loading instructions or aids (such as fuel tank tabs) will enable the operational pilot to stay in the approved c.g. envelope.
(3) Gross Weight Effects. The test pilot is expected to determine the effect that gross weight, including low-fuel state, may have on the airplane's flight characteristics. If it is found the flight characteristics would be adversely affected, tests should be performed for trim, stability, and controllability including VMC, stalls, and spins under the most adverse weight condition. Separate loading restrictions may apply to certain flight operations, such as spins.
(4) Lateral Loads. If possible loading conditions can result in a significant variation of the lateral c.g., this lateral range of center of gravity must be established by:
(i) The limits selected by the applicant;
(ii) The limits for which the structure has been proven; or
(iii) The limits for which compliance with all the applicable flight requirements has been demonstrated. The demonstrated weight and c.g. combinations should consider asymmetric loadings. When investigating the effects of asymmetric lateral loads, the following sections in this Flight Test Guide (FTG) represent applicable flights requirements:
§ 23.143 Controllability and Maneuverability, General.
§ 23.147 Directional and lateral control.
§ 23.149 Minimum control speed.
§ 23.151 Acrobatic maneuvers.
§ 23.157 Rate of roll.
§ 23.161 Trim.
§ 23.177 Static directional and lateral stability.
§ 23.201 Wings level stall.
§ 23.203 Turning flight and accelerated turning stalls.
§ 23.221 Spinning.
§ 23.233 Directional stability and control.
§ 23.701 Flap interconnection.
b. Procedures. None.
8. SECTION 23.25 WEIGHT LIMITS.
a. Explanation.
(1) Maximum Weight Limits. The maximum weight may be limited in three ways: at the election of the applicant, by structural design requirements, or by flight requirements.
(2) Maximum Weight Exceptions. The regulations concerning design maximum weight allow an exception that some of the structural requirements may be met at a lesser weight known as a design landing weight, which is defined in § 23.473. (See Advisory Circular (AC) 23-7 if the airplane is being modified for an increase in maximum weight.) Due to changes in the operational requirements of an owner/operator, in many cases the need arises to modify and substantiate the structure for an increase in maximum weight and maximum landing weight. Any one of these increases affects the airplane's basic loads and structural integrity, and they could affect the limitations and performance.
If an airplane was certificated with maximum landing weight equal to maximum weight, some applicants take advantage of the 5 percent difference between design landing and design maximum weight permitted by § 23.473(b). These applicants use the supplemental type certificate (STC) process. In these cases, re-substantiation of the landing gear for landing loads is not required when increasing the maximum weight by as much as 5 percent.
For those programs involving more than a 5 percent increase in maximum weight, some resubstantiation of the landing gear should be accomplished.
Other applicants are replacing piston engines with turbopropeller engines, thus requiring that gasoline be replaced with jet fuel, which weighs as much as 17 percent more. In some cases, the quantity of fuel is being increased at the same time as engine replacement, but the maximum zero fuel weight remains the same.
All the above types of modifications should be investigated to verify that critical loads have not increased or that those loads that have increased are capable of being carried by the existing or modified structure.
(3) Weight, Altitude, Temperature (WAT). For all airplanes with a maximum takeoff weight exceeding 6,000 pounds and turbine engine airplanes, a WAT chart may be used as a maximum weight limitation.
(4) Ramp Weight. The applicant may elect to use a "ramp weight" provided compliance is shown with each applicable section of Part 23. Ramp weight is the takeoff weight at brake release plus an increment of fuel weight consumed during engine start, taxiing, and run-up.
Generally, this increment of fuel should not exceed 1 percent of the maximum permissible flight weight up to 125 lbs. The pilot should be provided a means to reasonably determine the airplane gross weight at brake release for takeoff. A fuel totalizer is one way of providing the pilot with fuel on board. Alternately, a mental calculation by the pilot may be used, if the pilot is provided the information to make the calculation and the calculation is not too complex. Normally, fuel for engine start and run-up will be sufficiently close to an amount fixed such that taxi can be considered as the only variable. If the pilot is provided with taxi fuel burn rate in pounds per minute, then the resulting mental calculation is acceptable. The pilot will be responsible to ensure that the takeoff gross weight limitation is complied with for each takeoff, whether it is limited by altitude, temperature, or other criteria. The maximum ramp weight should be shown as a limitation on the Type Certificate (TC) Data Sheet and in the AFM.
(5) Lowest Maximum Weight. Sections 23.25(a)(2)(i) and 23.25(a)(2)(ii) require that each of the two conditions, (i) and (ii), must be considered and that the maximum weight, as established, not be less than the weight under either condition. This has to be shown with the 7