(MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) INFORMATION:
Attachment 4 includes a Figure 2 for Thomas Copter Mods TDC to affix a Twidget installation on Thomas Copter model T-97J helicopter.
Figure 2 is intended to assist in determining which requirements are applicable to this certification project. The document contains each requirement with a set of parentheses, the appropriate regulation, and the location of information in the applicant's ICA.
Information obtained from Attachment 4 can be used to determine which requirements are applicable. For requirements that are not applicable, place an NIA in the parentheses. All other requirements would be applicable to the certification project. Place a Y if the required information is included in ICA. Figure 2 has been completed for the sample Twidget TDC.
Applicant that uses and completes Figure 1 and indicates the location of that information in the applicant's proposed ICA will reduce the time required to evaluate the ICA.
It is important that the applicant include the project number or numbers associated with the ICA, the name of the appropriate FAA/AUTHORITY office, the name of the project engineer, the applicant's company name, the make and model of rotorcraft being modified, and the date.
The completed Figure 1 should be submitted to FAA/AUTHORITY with the applicant's ICA.
REVISION: (DATE) Revision 4 Page 4 Page Apdx A - 65
AC 27-1B, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) APPENDIX A PART 27 REQUIREMENTS The following is a breakdown of Appendix A to FAR/JAR Part 27 and is intended to provide guidance to assist an applicant for a Type Design Change under a Type Certificate (TC), Supplemental Type Certificate (STC), or Field Approval (FA) requiring Instructions for Continued Airworthiness (ICA). The breakdown is intended to provide guidance to assist an applicant in understanding the ICA requirements of FAR/JAR § 27.1529. An applicant may use the guidance to prepare the ICA. Completion of this appendix will provide information needed for the evaluation and will reduce the time required for evaluation of the proposed ICA.
() Status of ICA: Y = Yes included; N/A = non-applicable. The Location Column lists the page number in the Applicant's ICA that contains the information.
Project Number(s) ST01998RC-R ACO/FSDO: Rotorcraft ACO Project Engineer: Data Mastermine Applicant: Thomas Copter Mods Make: Thomas Copter Model: T97-J Date June 18, 1998 Requirement Regulation Location (NIA) ICA for each engine A27.1(b) N/A (NIA) ICA for each rotor A27.1(b) N/A (Y) ICA for each appliance required by this chapter A27.1(b) * All (Y) Any required information relating to the interface of the A27.1(b) See (Y) appliances, (N/A) engines and (N/A) rotors with the rotorcraft. NOTE 1 (Y ) If ICA are not supplied by the manufacturer of an A27.1 * All (NA) appliance, (NA) engine or (NIA) rotor installed in the rotorcraft, the ICA for the rotorcraft must include (Y ) the information essential to the continued airworthiness of the rotorcraft.
(Y ) A program showing how changes to the applicant's ICA will be A27.1(c) ATA O distributed.
(NIA) A program showing how changes to the ICA of the A27.1(c) N/A manufacture of the engine(s), rotor(s) and appliances installed in the rotorcraft will be distributed, if referenced in applicant's ICA (Y ) ICA that must be in a form of a manual or manuals as A27.2(a) * All appropriate for the quantity of data.
(Y ) A format of the manual or manuals which must provide for a A27.2(b) * All practical arrangement.
(Y) Content prepared in the English language. A27.3 * A11 Figure 2 REVISION: (DATE) Revision 4 Page 5 Page Apdx A - 66
( MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location (Y ) Introduction information that includes (Y ) an explanation of A27.3(a)(1) ATA O the rotorcraft's features and (Y) data to the extent necessary for maintenance and preventive maintenance.
(Y ) A description of the (IN/A) rotorcraft and its systems and A27.3(a) (2) ATA 25 installations, (N/A) engines and its systems and installations, (NA) rotors and its systems and installations, (Y ) appliances and its systems and installations.
(Y) Basic control and operating information describing (Y A27.3(a) (3) ATA 25 ) how the rotorcraft components and systems are controlled and (Y ) how the rotorcraft components and systems are operated including (Y) any special procedure and limitations.
(Y ) Servicing information that covers details regarding (Y A27.3(a) (4) ATA 12 ) servicing points, (NA) capacities of tanks, (Y ) capacities of reservoirs, (Y ) types of fluids to be used, (Y ) pressures applicable to the various systems.
(Y ) Location of access panels for (Y ) inspection and (Y A27.3 (a) (4) See ) servicing. NOTE 2 (Y) Servicing information that covers details regarding (Y A27.3(a) (4) ATA 12 ) locations of lubrication points, (Y ) the lubricant to be used.
(Y) Equipment required for servicing. A27.3(a) (4) ATA 12 (Y ) Tow instructions and limitations. A27.3(a) (4) ATA 9 (Y) Mooring information A27.3(a)(4) ATA 10 (NA) Jacking information A27.3(a) (4) N/A (NA) Leveling information A27.3(a) (4) NA (Y ) Scheduling information for each part of the (Y ) rotorcraft A27.3(b)(1) See that, provides the recommended periods at which they should (Y) NOTE 3 cleaned, (Y) inspected, (Y ) adjusted, (Y ) tested, lubricated and (Y) the work recommended at these periods.
(NA) Scheduling information for the (NA) rotorcraft's engine(s) A27.3(b)(1) N/A that provides the recommended periods at which they should be (IN/A) cleaned, (IN/A) inspected, (IN/A) adjusted, (N/A) tested, (N/A) lubricated and (N/A) the work recommended at these periods.
NOTE: This information may be in the FAA/AUTHORITY accepted engine ICA.
Figure 2 (continued) REVISION: (DATE) Revision 4 Page 6 Page Apdx A - 67
AC 27-1B, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location (NA) Scheduling information for the (N/A) rotorcraft's auxiliary A27.3(b)(1) N/A power unit(s) (APU) that provides the recommended periods at which they should be (NA) cleaned, (N/A) inspected, (N/A) adjusted, (N/A) tested, (N/A) lubricated and (N/A) the work recommended at these periods.
(N/A) Scheduling information for the (N/A) rotorcraft's rotor(s) that A27.3(b)(1) N/A provides the recommended periods at which they should be (N/A) cleaned, (N/A) inspected, (N/A) adjusted, (N/A) tested, (NA) lubricated and (IN/A) the work recommended at these periods.
(Y ) Scheduling information for the (Y ) rotorcraft's accessories A27.3(b)(1) See that provides the recommended periods at which they should be (Y ) NOTE 3 cleaned, (Y) inspected, (Y ) adjusted, (Y ) tested, (Y ) lubricated and (Y) the work recommended at these periods.
(Y) Scheduling information for the (Y ) rotorcraft's instruments A27.3(b)(1) See that provides the recommended periods at which they should be (Y ) NOTE 3 cleaned, (Y ) inspected, (Y ) adjusted, (Y ) tested, (Y ) lubricated and (Y) the work recommended at these periods.
(Y ) Scheduling information for the (Y ) rotorcraft's equipment A27.3(b)(1) See that provides the recommended periods at which they should be (Y NOTE 3 ) cleaned, (Y) inspected, (Y) adjusted, (Y ) tested, (X) lubricated and (Y) the work recommended at these periods.
(1) The degree of inspection for each part of the (NA) rotorcraft A27.3(b)(1) ATA 5 and its (N/A) engine(s), (N/A) auxiliary power unit, (INVA) rotor(s), (Y ) accessories, (Y ) Instruments and (Y ) equipment.
(Y) The applicable wear tolerances A27.3(b)(1) ATA 25 The applicant may refer to an (NA)accessory, (NA) instrument, or A27.3(b)(1) N/A (NA) equipment manufacturer as the source of this information if the applicant shows (NIA) that the item has an exceptionally high degree of complexity requiring specialized maintenance techniques, test equipment, or expertise.
(1) The recommended overhaul periods and necessary cross A27.3(b)(1) ATA 5 references to the Airworthiness Limitation Section.
Figure 2 (continued) REVISION: (DATE) Revision 4 Page 7 Page Apdx A - 68
(MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location (Y) An inspection program that includes (Y ) the frequency and ( 427.3(b)(1) ATA 5
1) extent of the inspection necessary to provide for the continued airworthiness of the rotorcraft.
(Y) Troubleshooting information describing (Y ) problem A27.3(b)(2) See malfunctions, (Y) how to recognize those malfunctions and (Y NOTE 4 ) the remedial action for those malfunctions.
(N/A) Information describing the order and method of A27.3(b)(3) N/A (NA) removing and (NA) replacing engine(s) with any necessary precautions to be taken.
(NA) Information describing the order and method of A27.3(b)(3) N/A (NA) removing and (NA) replacing rotor(s) with any necessary precautions to be taken.
(Y) Information describing the order and method of (Y A27.3(b)(3) ATA 25 ) removing and (Y ) replacing parts with any necessary precautions to be taken.
(Y) Other general procedural instructions including (NA) storage A27.3(b)(4) ATA 8 limitations and procedures for (NIA) testing system during ground running, (N/A) making symmetry checks, (Y ) weighing and determining the center of gravity, (IN/A) lifting, (IN/A) shoring.
(NA) Diagrams of structural access plates and information needed A27.3(c) N/A to gain access for inspections when access plates are not provided.
(NA) Details for the application of special inspection techniques A27.3(d) N/A including radiographic and ultrasonic testing where such process are specified.
(NA) Information needed to apply protective treatment to structure A27.3(e) N/A after inspection.
(Y) All data relative to structural fasteners such as (Y A27.3(Đ) ATA25 ) identification, (Y) discarded recommendations, and (X) torque values.
(Y) A list of special tools needed A27.3(g) NOTE 5 (Y) The Instructions for Continued Airworthiness must contain a A27.4 ATA 4 section, titled Airworthiness Limitations that is (X) segregated and (Y ) clearly distinguishable from the rest of the document. NOTE: The Airworthiness Limitations Section in the applicant's ICA will be evaluated by the appropriate FAA/AUTHORITY.
Figure 2 (continued) REVISION: (DATE) Revision 4 Page 8 Page Apdx A - 69
AC 27-1B, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location (NA) The Airworthiness Limitations Section must set forth each A27.4 N/A mandatory replacement time, structural inspection procedure approved under § 27.571.
(Y ) If the Instructions for Continued Airworthiness consist of A27.4 ATA 4 multiple documents, the Airworthiness Limitations Section required by this paragraph must include in the principal manual.
(Y ) The Airworthiness Limitations Section must contain a legible A27.4 ATA4 statement in a prominent location indicating that the Airworthiness Limitations Section is FAA/AUTHORITY-approved and specifies required maintenance and/or inspections. The exact, required wording of this statement is found in the FAR/JAR.
Figure 2 (continued) NOTE: The Airworthiness Limitations Section (ALS) is evaluated and approved by FAA/AUTHORITY.
REVISION: (DATE) Revision 4 Page 9 Page Apdx A - 70
(MANUAL IDENTIFICATION)
THIS PAGE INTENTIONALLY LEFT BLANK REVISION: DATE Revision 4 ade 10 Page Apdx А - 71
AC 27 APPENDIX B. AIRWORTHINESS GUIDANCE FOR ROTORCRAFT INSTRUMENT FLIGHT.
a. Explanation.
(1) Requirements for instrument flight rules (IFR) have been incorporated into Appendix B to part 27, Amendment 19. Various information from previous interim standards, procedures, test techniques, and acceptable means of compliance for rotorcraft IFR flight is included in the following sections.
(2) Amendment 27-44 made a change to paragraph V. Static Lateral Directional Stability, concurrent with the change to § 27.177, to allow for a small range of sideslip angles (2-3 degrees) for which sideslip angles need not increase steadily with control deflection. The previous rule language stating that directional control position must increase in approximate constant proportion with sideslip angle has been replaced. The intent of this change is that an increase in directional control position must produce an increase in sideslip angle linearly. At greater sideslip angles appropriate to the type rotorcraft, increase in directional control position need not produce a linear increase in sideslip angle but should not become neutral or negative. The change in paragraph VIl revised the current requirement to clearly state the requirements to be met in the event of a stability augmentation system (SAS) failure.
b. Procedures.
(1) General.
(i) The certificated instrument flight envelope may be more restrictive than the visual flight rules (VFR) envelope in terms of weight, CG, speed, altitude, or rate of climb and descent. The approved envelope should be operationally practical and not impose constraints with which the crew has difficulty complying. The IFR altitude envelope should extend to at least 10,000 feet to be operationally practical in the National Airways System.
(ii) Controllability requirements are to be met from 0.9 VMINI to 1.1 VNEI. Stability requirements must be met where specified. Stability devices are to be designed to allow safe flight following failures.
The evaluating pilot should assure that all equipment and devices installed for FR, including reasonable failures of that equipment, do not compromise the VFR approval for that rotorcraft. For example, stability system failures can cause loss of swashplate or tail rotor control travel when failed in a hardover condition. If the device remains in the hardover position after the stability system is turned off, control capability can be compromised. Cyclic controllability tests at high speed and at the limiting rearward flight condition, or tail rotor tests in sideward flight at high altitude, may reveal a lower control capability and a more restrictive envelope. Revision to the envelope approved for VFR conditions may be required when stability equipment is installed. In addition, controllability testing should be accomplished with the control rigging set at the most adverse production tolerance for the test condition (e.g., minimum forward swashplate for high speed testing).
(2) Trim. Compliance with the FR trim requirement may be met by use of a magnetic brake with a recentering button, an electrically driven trim system activated by a "beeper" type control, or other means, so long as the system does not introduce any objectionable discontinuities in the force gradient or otherwise result in objectionable flight characteristics. Trim release devices should be free of objectionable stick jump. Electrically driven trim systems should have a smooth change in force with a rate compatible with the normal rotorcraft maneuvers. Only the cyclic trim control must exhibit positive self-centering characteristics. Collective and directional controls are not required to incorporate positive self-centering characteristics. Movement of the trim controls should produce a similar effect on the rotorcraft in a plane parallel to that of the control motion. The control system free play and breakout force must be evaluated to assure a close and direct correlation between control input (force and deflection) ' Paragraph VII was effective 9/17/2009 as part of the new and changed guidance material for the Performance and Handling Qualities final rule (Amdt. 27-44, 73 FR 11000, Feb. 29, 2008).
Page Apdx B - 1
AC 27-1B, Chg 7 2/4/2016 and rotorcraft response (pitch, roll, yaw, and heave (vertical motion)), and to permit small, precise changes in flight path. If trim control is provided in a SAS, the control should be of such design and so installed that any failure will not create a hazardous condition. If an inadvertent out-of-trim condition can be developed, its effect on the rotorcraft should be investigated. There should be investigation of these failures or malfunctions as outlined in paragraph b.(7), Stability Augmentation Systems, below. Controls for this trim function should be installed such that the controls should operate in the plane and with the sense of motion of the rotorcraft. Each control means should have the direction of motion plainly marked thereon or adjacent to the control.
(3) Static Longitudinal Stability.
(i) Positive static longitudinal stability is a key IFR requirement, which assures a selfcorrecting airspeed response and allows a pilot to recognize any substantial change in speed. The phrase "substantial speed change" as used in Appendix B to part 27, paragraph IV., is normally considered to mean at least a 10 knot departure from trim speed. Such a change in airspeed must be accompanied by a stick force clearly perceptible to the pilot (i.e., a discernable and quantifiable force gradient). Very shallow force gradients can be approved for systems with low deadband and low friction.
Systems with significant friction and deadband require much steeper force gradients to be acceptable.
The longitudinal force gradient can be determined by either of two methods. The most commonly used method (applicable only to irreversible control systems) measures the cyclic forces with the rotorcraft on the ground and the rotor stopped (with hydraulic and electric power units if required). The force applied to the cyclic stick and the cyclic stick displacement is measured and a plot of stick force verses displacement in each longitudinal direction is obtained. Following the ground test, the longitudinal static stability tests are conducted in the air as described in section 27.175 of this AC. The cyclic displacement measurements gathered during flight test are then assigned force values from the ground mechanical characteristics test and the force values are cross plotted with the corresponding airspeeds to produce a plot of cyclic force verses airspeed. The trim system should be on during the test and the aircraft trimmed at the trim speed. After each end point, the cyclic should be allowed to slowly return to the trim position.
When all the force is released from the cyclic stick and the airspeed has stabilized, note the airspeed.
For single pilot approval only, the airspeed must return to within 10 percent or 10 knots, whichever is less, of the trim speed. An alternate method of determining the longitudinal stick force stability is to measure the force on the cyclic stick in flight using a hand held force gage or other force measuring instrumentation. The in-flight technique is the same as the first method. Testing should be accomplished at a minimum of two altitudes. One altitude should be low enough to assure limiting power is attained.
Another should be at or near the maximum approved altitude. Reasonable interpolation is allowed. If no marginal areas are apparent, interpolation over a 10,000 foot altitude range is considered reasonable.
(il) Tests for static longitudinal stability during approach should include the steepest approach gradient for which approval is requested. Static stability tests may be simulated by initially establishing a trimmed rate of descent for maximum approach gradient assuming zero wind conditions. Actual approach tests at the maximum approved gradient should be conducted to evaluate tracking and maneuverability, including the capability to correct downward to a glide path when approaching in a slight (10 knot) tailwind condition.
(iii) Rotorcraft that are approved for a minimum crew of two pilots for IFR operation are relieved from demonstrating stick force stability in climb, slow cruise, and descent. It is expected that these rotorcraft do comply with the VFR certification requirements of § 27.175.
(4) Static Lateral Directional Stability.
(i) Tests for directional stability usually require instrumentation for lateral cyclic position, pedal position, and sideslip angle. Testing for compliance with the specific directional requirement is relatively simple; however, the pilot should look for significant longitudinal trim changes, and short period dynamic modes, which might occur only during sideslip conditions. Side force characteristics are indicated by the variation of bank angle with sideslip during steady heading sideslips. The number of ball widths of deflection is also indicative of the side force cue available to the pilot. A correlation between sideslip Page Apdx B - 2
angle and ball widths of skid can be obtained at given speeds for use during later testing after sideslip instrumentation is removed. A simple yaw string can be calibrated in a similar manner. The TIA should define the maximum sideslip angles, which should not be exceeded during the flight test program. These angles must not be greater than the structural sideslip envelope substantiated and are not required to be that sideslip angle obtained with full directional pedal deflection. Sufficient side force cues should accompany sideslip to alert the crew when approaching sideslip limits. This is needed to assure that structural sideslip limits will not be inadvertently exceeded in service. Although not stated in the requirement, flight conditions for demonstration of static longitudinal stability are also appropriate for demonstration of static lateral-directional stability.
(ii) Dihedral requirements may be more difficult to assess. For those rotorcraft that do not meet the position and force gradient requirements for the conventional, cross-controlled sideslips, there are alternative tests that may be used to determine acceptable characteristics. If directional pedals are utilized in steady sideslips, the resultant rolling tendency is the sum of (1) the aircraft's roll due to sideslip tendency (dihedral), and (2) the aircraft's roll due to directional control input. If the rotorcraft has a tail rotor that is excessively high or low in relation to the rotorcraft's vertical center of gravity (CG), application of tail rotor thrust will introduce a significant rolling moment. The basic intent of dihedral stability testing is to determine the rotorcraft response to sideslip exclusive of directional control input. In general, if a tail rotor configuration is involved and the tail rotor is above the vertical CG of the rotorcraft, the effect of pedal input upon dihedral effect is destabilizing during conventional, control-induced sideslips.
(iii) There are two alternate methods that, for small angles of sideslip, can give an indication of the basic dihedral stability of the rotorcraft. Both methods involve freezing the directional controls while artificially creating sideslip by other means.
(iv) The first method is only applicable for rotorcraft with single main rotor systems. To utilize this method, the rotorcraft is stabilized in a given flight condition and small collective (torque) changes are applied in each direction (e.g., +5% and +10 %) while holding pedals fixed. Sideslip angle, lateral control position, and lateral control force may be measured and plotted for small torque changes from trim. This technique will not work for aircraft that have collective to pedal or collective to lateral control couplings.
(v) In the second method, the rotorcraft is stabilized in a trimmed flight condition with a small amount of bank (5°-10°). The rotorcraft is then rolled to an approximately equal angle of bank in the opposite direction holding the pedals fixed. The change in direction of bank results in a small change in sideslip angle and again sideslip angle may be plotted versus lateral control position or force. This test should be conducted in both directions and the results averaged. This method can give reasonably accurate results for small perturbations. Other factors contribute to the results of either of these two methods. It is always important to assess the roll due to sideslip tendency with pedal induced sideslips to assure lateral control forces are reasonable and in a proper direction for directional out-of-trim conditions, and to assure the pilot has adequate sideslip cues.
(vi) Wording of the dihedral requirement is intended to allow slightly negative dihedral stability at critical loading conditions. This will ordinarily result in positive dihedral stability throughout a great majority of the approved loading envelope. The test for maximum allowable negative dihedral effect would involve stabilization at a required flight condition, inducing a sideslip up to t10° from trim, then assessing lateral cyclic friction or deadband to determine if roll is restrained while remaining in the control system friction or deadband so that the control may be released without resulting in the aircraft rolling in the adverse direction. When testing for this condition, lateral cyclic friction should be adjusted to the
(vil) The intent of the dihedral rule is to allow small amounts of control system friction and deadband to mask small values of negative dihedral. Where slope of the negative dihedral versus sideslip exceeds these small values, the negative dihedral must not be approved. The operational pilot must not be presented with opposite cyclic sensing for similar sideslip conditions as loadings and flight conditions change. In general, large values of control system friction and deadband are undesirable. The Page Apdx B - 3
AC 27-1B, Chg 7 2/4/2016 addition of friction or deadband into the control system to satisfy the dihedral requirement is not acceptable.
(viii) In approving small, negative dihedral values, the pilot should ensure that other positive flight cues, such as suitable side force, accompany sideslip. This will aid the pilot in determining direction of sideslip so that no reverse sensing or confusion accompanies sideslip conditions.
(5) Dynamic Stability.
(i) Dynamic characteristics are defined in quantitative terms; however, some areas of interpretation and technique need special consideration:
(A) Unlike fixed-wing aircraft, where the size of the input has no effect on damping ratio, rotorcraft can be sensitive to the type and size of input used to excite each dynamic mode. For instance, it has been found that for the phugoid-type dynamic oscillation, damping ratio is inversely proportional to the size of the input. It therefore becomes important that dynamic excitations be sized to approximate the response of the rotorcraft in a moderate, turbulent gust. In addition, the dynamic input should be made with the control(s) that most accurately simulates the typical aircraft gust response. Obviously, for this evaluation some flying of the rotorcraft in turbulence is necessary to obtain knowledge of the rotorcraft's gust response. Pulses and doublets may be used to generate disturbances similar to a gust. To assist returning the controls) to the trim position, a hand held jig may be used. Use of attitude and rate instrumentation is desirable. The pilot may find that collective excitation, or collective in conjunction with cyclic, is most appropriate for gust simulation.
(B) The second area of concern in evaluating dynamic response is whether to let only one axis respond to an excitation or to let the rotorcraft respond in two or more axes. When it can be done safely, the rotorcraft should be allowed to follow its dynamic response in all axes. In other words, if pitch oscillations feed into roll, the pilot should attempt to observe and record the total aircraft dynamic response in both pitch and roll.
(C) The third area concerns strict compliance with the exact wording of the dynamic requirement. In this regard, a neutrally damped oscillation with a period of 19 seconds would not be acceptable; however, a very divergent oscillation that doubles in amplitude in 21 seconds would be acceptable. The 19-second oscillation is much less severe than the 21-second oscillation and yet is unacceptable by the "letter of the law." Figure AC 27.APX B-1 is a graphic display of the dynamic requirement. The 19 and 21-second oscillations are shown as points (1) and (2). Point No. 1 is positioned much more toward the acceptable portion of the graph and yet by the "letter of the law" is unacceptable. The intent of the dynamic requirement is roughly approximated by the dashed or curved line. Areas to the right of that line may be considered for findings of equivalent safety.
(D) A fourth area requiring special care in testing is the aperiodic requirement. The most common aperiodic motion is the spiral characteristic, which results when aircraft attitude is displaced in roll. The preferred method for testing this requirement is to stabilize precisely on a trimmed condition in straight flight, then displace the rotorcraft to 10° of bank, stabilize momentarily, set the controls as they were positioned for straight flight, and release them. Time and bank angles are then recorded. Recovery is initiated when bank angle or roll rate becomes excessive. Of particular interest is the time for bank angle to pass 20°, and this time should not be so short as to cause the aircraft to have objectionable flight characteristics in the IFR environment. The time period to double amplitude (20°) should be at least 9-seconds. It is vitally important that controls (particularly lateral cyclic) are positioned exactly as it was for the straight flight condition. If a high resolution force trim system is not incorporated, an alternative method may be used. In this second method, the rotorcraft is trimmed for straight flight as described above and controls are released. Roll attitude may simply be allowed to vary naturally with time or small pulse input may be made with pedals. It is important that controls be positioned precisely as they were for the trimmed, straight flight condition and a plot of bank angle versus time is obtained. This plot is then compared against a divergent roll condition that doubles in amplitude every 9-seconds. Of particular interest is again the rate passing 20° of bank. If airspeed changes as the aircraft rolls or if roll or pitch Page Apdx B - 4
coupling occurs, these changes should be allowed to interact naturally until recovery is necessary. Due to the sensitive nature of this test, smooth air is essential. Repeatability may be a problem. At least two test points in each direction should be obtained at each trim condition. Results may be averaged if they show reasonable repeatability. The same procedures may be utilized for an aperiodic pitch response;
however, a displacement of 5° from trim should be used, and of particular importance is the pitch rate passing 10°. Again, at least two test points in each direction should be obtained for each trim condition.
Although not stated in the requirement, the flight conditions for demonstration of static longitudinal stability are also appropriate for demonstration of dynamic stability. Rotorcraft certificated for a minimum crew of two pilots are required to demonstrate longitudinal static force stability in the cruise and the approach configuration. Compliance with the dynamic stability requirements should be demonstrated for these configurations, and the rotorcraft should be free from rapid and excessive rates of divergence in the other flight configuration. The degree of testing referred to here represents that which might be required of a marginally stable rotorcraft. For those configurations that provide good aerodynamic stability or use varying degrees of SAS, the scope of the demonstration program would be decreased significantly.
(ii) Control system dynamics should also be evaluated. This may be accomplished by lightly bumping each control in flight and observing its free response. Any resulting control motion must dampen quickly and should not be driven by aircraft or control system interaction. This will ensure safe flight in the
(6) Automatic Flight Control System (AFCS)
(i) From a regulatory compliance standpoint, the AFCS used on most modern rotorcraft often performs two different and distinct functions. These two functions are to:
(A) Enhance the inherent basic stability of the aircraft to enable compliance with applicable flight characteristic requirements by using automatic control features, such as SAS, which may incorporate an attitude hold mode (ATT); and (B) Control aircraft flight path using a simple ATT in conjunction with the SAS or autopilot modes (coupled flight director), such as airspeed hold, altitude hold, radio navigation, and precision approach.
(ii) Definitions.
(A) Autopilot (AP). The AP, also known as coupled flight director, is an automatic mechanical, electrical, or hydraulic control system primarily intended to assist the flight crew in the guidance of the aircraft. The various AP control modes are designed to provide workload relief to the pilots and a means to fly a flight path more accurately to support specific operational requirements.
(B) Attitude Hold Mode (ATT). ATT is an automatic flight control system mode that maintains established pitch and roll attitudes and, in some cases, provides yaw damping, yaw hold, or heading hold.
(C) Flight Director (FD). The FD is a guidance system that provides an automatically computed visual cue or set of cues, used during manual control of the aircraft as steering command information, which direct the pilot how to maneuver the aircraft (usually in pitch, roll, and collective) to track a desired flight path.
(D) Stability Augmentation System (SAS). The SAS is an automatic control system mode that augments the inherent stability of the aircraft. The SAS aspects of the AFCS are not covered in § 27.1329 (Automatic pilot system) but rather in § 27.672. Nevertheless, the guidance provided in this section for pilot response times is applicable to SAS malfunction testing.
(ili) AFCS Malfunctions.
Page Apdx B - 5