(4) The AFCS sub-mode system architecture should support the following functionalities:
(i) A system for limiting the engine power demanded by the AFCS when any of the automatic piloting modes are engaged, so that FADEC power limitations such as torque and temperature are not exceeded.
(i) If applicable, a system providing the aircraft height above the surface and final pilot-selected height at a location on the instrument panel in a position acceptable to the FAA that will make it plainly visible to and usable by any pilot at their station.
(iii) A system providing the aircraft heading and the pilot-selected heading at a location on the instrument panel in a position acceptable to the FAA that will make it plainly visible to and usable by any pilot at their station.
(iv) If applicable, a system providing the aircraft longitudinal and lateral ground speeds and the pilot-selected longitudinal and lateral ground speeds when used by the AFCS in the flight envelope where airspeed indications become unreliable. This information must be presented at a location on the instrument panel in a position acceptable to the FAA that is plainly visible to and usable by any pilot at their station.
(v) A system providing wind speed and wind direction when automatic piloting modes are engaged or transitioning from one mode to another.
(vi) A system that monitors for flight guidance deviations and failures with an appropriate alerting function that enables the flight crew to take appropriate corrective action.
(vii) An alerting system that provides visual or aural alerts, or both, to the flight crew when (if applicable) the stored or pilot-selected safe minimum height is reached, when an AFCS malfunction occurs, and when the AFCS changes modes automatically from one AFCS mode to another.
For normal transitions from one AFCS mode to another, a single visual or aural alert may suffice.
For an AFCS mode malfunction or a mode having a time-critical component, the flight crew alerting system must activate early enough to allow the flight crew to take timely and appropriate action. The alerting system means must be designed to alert the flight crew in order to minimize
(5) The reliability of the AFCS must be related to the effects of its failure. The occurrence of any failure condition that would prevent continued safe flight and landing must be extremely improbable. For any failure condition of the AFCS that is not shown to be extremely improbable, the helicopter must be safely controllable and capable of continued safe flight without exceptional piloting skill, alertness, or strength. Additional unrelated probable failures affecting the control system should be evaluated. Additionally, the AFCS must be designed so that it cannot create a hazardous deviation in the flight path or produce hazardous loads on the helicopter during normal operation or in the event of a malfunction or failure, assuming corrective action begins within an appropriate period of time. Where multiple systems are installed, subsequent malfunction conditions should be evaluated in sequence unless their occurrence is shown to be improbable. A functional hazard assessment and a system safety assessment should be provided in accordance with section 27.1309 of this AC to address the failure conditions associated with the AFCS modes. The assessments should consider all systems required for AFCS mode operation, including the AFCS, all associated AFCS sensors (for example, radio altimeter), and primary flight displays. Electrical and electronic systems with catastrophic failure conditions (for example, AFCS) must comply with the § 27.1317(a)(4) High Intensity Radiated Field requirements.
(6) The AFCS modes should be demonstrated in the requested flight envelope.
Page Apdx B - 19
AC 27-1B, Chg 7 2/4/2016
(7) For any single failure or any combination of failures of the AFCS that is not shown to be extremely improbable, the recovery should not result in a loss of height greater than half of the minimum use height.
(8) For coupled flight below the previously established VMINI, at the maximum demonstrated winds, the helicopter must be able to maintain any required flight condition and make a smooth transition from any flight condition to any other flight condition without requiring exceptional piloting skill, alertness, or strength, and without exceeding the limit load factor.
(9) For coupled flight below the previously established VMINI, the following stability requirements replace the stability requirements of paragraph IV, V, and VI of of Appendix B to part 27:
(i) Static Longitudinal Stability: The requirements of Appendix B to part 27, paragraph IV are not applicable.
(i) Static Lateral-Directional Stability: The requirements of Appendix B to part 27, paragraph V are not applicable.
(iii) Dynamic Stability:
(A) Any oscillation must be damped and any aperiodic response must not double in amplitude in less than 10 seconds. This requirement must also be met with degraded upper mode(s) of the AFCS.
(B) After any upset, such as a wind gust, the AFCS must return the aircraft to the last commanded position within 10 seconds or less.
(10) With any of the upper mode(s) of the AFCS engaged, the pilot must be able to manually recover the aircraft and transition to the normal (Appendix B to part 27) FR flight profile envelope without exceptional skill, alertness, or strength.
Page Apdx B - 20
2/4/2016 FIGURE AC 27.APХ B-1 ROTORCRAFT DYNAMIC STABILITY 35 30
ACCEPTABLE
REQUIREMENTS FOR IFR
UNACCEPTABLE Page Apdx B - 21 -0.2 0.05 Ø.15 AC 27-1B, Chg 7
DAMPING RATIO
AC 27 APPENDIX B (AMENDMENT 27-51) AIRWORTHINESS GUIDANCE FOR ROTORCRAFT INSTRUMENT FLIGHT.
a. Explanation.
(3) Amendment 27-51 revised section VIII (b)(5)(i), which requires isolating the pilot instrument system from any other operating systems, to only apply to pneumatic systems. This change allows other types of pilot instrument systems to be connected to other systems on the rotorcraft and allows the use of modern technology to monitor and display highly integrated information. This guidance remains unchanged except paragraphs (b)(9)(v) and (b)(9)(vi) of this AC section do not apply to nonpneumatic systems.
Page Apdx B - 22