АС 27-1A 7/30/97 this task. The test proposal may be used to define and to authorize the means to accomplish inspection of the test fixtures and instrumentation. Unnecessary drawings such as test fixture details or layering of approvals are not intended or envisaged by this policy. Drawings, sketches, or photographs have been used by the FAA/AUTHORITY to control and to ensure correct location, direction, and magnitude of loads and other critical test parameters.
(3) Structural analysis has been accepted for rotorcraft in place of static tests.
Generally, the rotorcraft airframe should have natural frequencies remote to predominant rotor excitation sources, including higher harmonics, to avoid undesirable and possibly excessive vibration and potentially high operating stress levels due to this vibration. During the flight load measurement program conducted under § 27.571, critical loaded areas or critical joints may be instrumented with strain gages or other stress strain measuring devices. This actual flight data should be compared to the analytical data to verify accuracy.
(4) Paragraph (b) of the rule specifies certain tests. Test proposals should be approved prior to conducting official FAA/AUTHORITY tests. Other paragraphs in this advisory circular pertain to those tests.
124A. § 27.307 (Amendment 27-26) PROOF OF STRUCTURE.
a. Explanation. Amendment 27-26 adds the requirement to account for the environment to which the structure will be exposed in operation. This change is intended to codify recent FAA/AUTHORITY and industry practices for the consideration of environmental effects in showing "proof of structure."
b. Procedures. All of the policy materials pertaining to this section remains in effect with the following additions:
(1) For either tests or an analysis, environmental effects are now explicitly required. Consideration of loss of strength and stiffness of metals with elevated temperatures and loss of strength and stiffness of composite materials from exposure to heat, moisture, or other operational environments is now required and should be documented in analyses and test reports.
(2) MIL-HDBK-5, AC 20-107B, or MIL-HDBK-17B (or later versions) are acceptable sources of data and procedures to show compliance with environmental effects of metallic and composite materials, respectively.
125. § 27.309 DESIGN LIMITATIONS.
a. Explanation.
170 Par 124
(1) The rule requires an orderly selection and presentation of the basic structural design limitations of the rotorcraft. The applicant is required to establish these structural limitations to facilitate design of the rotorcraft.
(2) Refer to the rule for the specific requirements.
b. Procedures.
(1) The design criteria and/or design load report should contain the design limits specified.
(2) These items are structural design limits. Other requirements may result in narrowing the ranges of type design limits or in reducing limits. It is not necessary to revise structural design criteria limits to agree with more conservative operational limits established during the certification program. The operational limits may be subsequently expanded by additional flight tests to agree with design limits.
Par 125 171
126.-134. RESERVED.
Intentionally Left Blank 172 (thru 180) Par 126
135. RESERVED.
Intentionally Left Blank Par 135 181
SECTION 8. FLIGHT LOADS
136. § 27.321 (Amendment 27-11) GENERAL.
a. Explanation.
(1) The rule specifies the way the loads will be applied to the rotorcraft. It requires load analysis from minimum to maximum design weight. Any practical distribution of disposable loads must be included in the analysis.
(2) Paragraph (a) of the rule states:The flight load factor must be assumed to act normal to the longitudinal axis of the rotorcraft, and to be equal in magnitude and opposite in direction to the rotorcraft inertia load factor at the center of gravityi
b. Procedures.
(1) Derivation of the flight loads is required by and specified in §§ 27.337 through 27.351. This rule requires flight load determination from minimum to maximum weight and for disposable loads.
(2) The application of the design loads derived from the flight load factor will be as specified. The flight loads analysis data must comply with the rule.
137. § 27.337 (Amendment 27-26) LIMIT MANEUVERING LOAD FACTOR.
a. Explanation. The rotorcraft must be designed and substantiated to load factors as specified to provide a minimum level of structural integrity of the rotorcraft airframe and rotors.
(1) A range of design positive load factors from +3.5 to +2.0 may be used.
(2) A range of design negative load factors from -1.0 to -0.5 may be used.
(3) Load factors inside the range of +3.5 to -1.0 may be used provided the probability of exceeding the design load factors is shown by analysis and flight tests to be extremely remote and the selected load factors are appropriate to each weight condition between design maximum and minimum weight.
(4) Load factors exceeding these "minimums" may be used.
b. Procedures.
182 Par 136
(1) The applicant may elect to substantiate the rotorcraft for a design maneuvering load factor less than +3.5 and more than -1.0. Whenever this option is used, an analytical study and flight demonstration are required.
The maximum positive design load factor of +3.5 is generally at a weight below maximum gross weight. The maximum thrust capability of the main rotor, combined with incremental lift of wings or sponsons, if installed, results in a maximum design positive load factor. An example of a load factor-gross weight curve is shown in Figure 137-1. Note the minimum positive design load factor is +2.0 even though the required analysis and flight demonstration may prove the rotorcraft is not capable of achieving this load factor. This curve also illustrates compliance with § 27.321(b)(1) since the design load factor varies with gross weight.
(її) The largest negative design load factor is -1.0; however, several current rotorcraft designs are not capable of achieving a negative load factor.
Therefore, -0.5 has been an acceptable structural design negative load factor for certain rotorcraft designs.
(2) Whenever the applicant analytically substantiates the lower load factors allowed by § 27.337(b), the flight demonstration required by § 27.337 (b) must be conducted. The flight test personnel should determine that the demonstration shows the probability of exceeding the selected design load factors (those factors less than +3.5 and more than -1.0) is extremely remote. (See Order 8110.4, Paragraph 166c(2)(c)).
(3) A numerical value has not been assigned to "extremely remote" in this standard.
Par 137 183
+3.5 Represents curve of Design thrust + lift Load Factor
• +2.0 Nz -1.0 Minimum Gross Weight Lbs. Maximum
LOAD FACTOR GROSS WEIGHT CURVE FIGURE 137-1 184 Par 137
138. § 27.339 (Amendment 27-11) RESULTANT LIMIT MANEUVERING LOADS.
a. Explanation. The rule specifies or defines the application of rotor and lift surtace loads to the rotorcraft.
(1) The design maneuvering load factors required by § 27.337 will result in or be derived from rotor thrust or lift and from auxiliary surface lift.
(2) Sections 27.321, 27.337, and 27.341 all complement one another and result in the derivation of design flight loads that will be imposed to ensure structural integrity of the rotorcraft.
(3) The following assumptions and conditions are specified in the rule.
(i) The rule requires application of appropriate loads at each rotor hub and auxiliary lifting surface.
(ii) Power-on and power-off flight with maximum design rotor tip speed ratio and specific conditions that must be considered.
(Il) Rotor tip speed ratio, defined in the rule, has been carried forward from the initial rotorcraft certification rules issued in 1946. The rotor tip speed ratio is a basic parameter used in calculating rotor aerodynamic forces.
b. Procedures.
(1) The rule specifies an acceptable assumption concerning application of the rotorcraft maneuvering loads.
(2) The rotor tip speed ratio is a parameter found in textbooks and other books such as NACA Report No. 716. The equation in the rule contains angle "a." Report No. 716 also defines angle "a" as the angle of attack of the rotor disk. This definition is more easily understood than the definition contained in the rule.
(3) The rotorcraft design loads are derived as prescribed by $$ 27.321, 27.337, and 27.341. These loads are applied to the rotor or rotors and any auxiliary surface as prescribed by this rule.
139. §27.341 GUST LOADS.
a. Explanation.
(1) The rotorcraft must be substantiated for the loads derived from 30 feet per second vertical gusts from hovering to 1.11 VNE (i.e., VD).
Par 138 185
AC 27-1A 7130/97
(2) Gust loads for any horizontal stabilizing surface should be derived for vertical gusts, upward and downward.
b. Procedures.
(1) Either sharp-edged (instantaneous) gusts or sharp-edged gusts modified by an alleviation (attenuation) factor may be used for calculating aerodynamic loads for the rotorcraft and any installed stabilizing surfaces. The following conditions may be used:
Vertical gusts may be considered normal to the flight path of the rotorcraft except during hover or low speed flight (20 knots or less) when the gusts may be assumed normal to the longitudinal axis of the rotorcraft.
(ii) A primary effect of encountering the gust is to change the lift of the rotors and rotorcraft surfaces. Of primary concern is the gust load or lift created by the main rotor or rotors. The lift increment of the horizontal stabilizing surface and fuselage is generally negligible when compared to the rotor and may be neglected for the rotorcraft gust load determination if proven negligible by analysis.
(Hi) The rotorcraft shall be assumed in stabilized level flight prior to meeting the gust.
(iv) The gust velocity may be assumed uniform across the rotorcraft.
(V) Gust loads on the stabilizing surfaces are required as stated in Paragraph 159 of this advisory circular.
(2) The rotorcraft design maneuvering load factors may generally exceed the design gust load factors calculated in compliance with this rule. This may be attributed to the small incremental change in lift due to the 30 FPS gust. Nonetheless, design gust loads for the rotorcraft shall be calculated as specified in the rule to ensure the rotorcraft maneuvering load factors do, in each case, exceed the design gust load factor.
(3) For further information about rotorcraft gust response characteristics, see Paper No. 9 presented at the AHS/NASA -Ames Specialist's Meeting on Rotorcraft Dynamics, February 13-15, 1974. The paper, entitled, "Helicopter Gust Response Characteristics Including Unsteady Aerodynamics Stall Effects,i was written by P.J.
Arcidiacono, R.R. Berquist, and W.T. Alexander, Jr. References listed in the paper may be helpful also.
140. § 27.351 (Amendment 27-26) YAWING CONDITIONS.
a. Explanation. The standard was added by Amendment 27-26. It requires proof of a rotorcraft "structural" yaw or sideslip design envelope. This sideslip envelope 186 Par 139
should cover minimum forward speed or hover to the lesser of VH or VNE for "power-on" condition, not "power-off" since Vy is a part of the standard. The rotorcraft should be structurally safe for the thrust capability of the directional control system as stated.
(1) The rotorcraft structure should be designed to withstand the loads for the specified yaw conditions. The standard does not require a structural flight demonstration. It is a structural design standard.
(2) Maximum displacement of the directional control, except as limited by pilot effort (130 pounds derived from § 27.397(a)), is required for the conditions cited in the standard. A control system rate limiter or a yaw damper may be used as part of the type design required equipment, if elected. The total displacement is therefore a function of time as well as the maximum effort applied such as 130 pounds.
(i> At low airspeeds from 0 to 0.6 VNE, 90° yaw (sideward flight) is specified as the design limit.
(Ii) At high airspeeds VH or VNE), stabilized yaw angle (stabilized sideslip) or 15° sideslip, whichever is less, is specified to be substantiated.
(iii) At high airspeeds, the maximum tail rotor thrust will be combined with the vertical (directional) stabilizer surface load, if a stabilizer is used, as specified by § 27.351(b)(1).
(iv) At high airspeeds, while the rotorcraft is in the sideslip condition, the directional control is then returned to the neutral position, attendant with the flight condition. The tail rotor thrust will be added to the restoring force of the vertical stabilizer.
(v) Both right and left yaw conditions should be proven.
b. Procedures.
(1) Many of the current single main rotor rotorcraft designs have vertical (directional) stabilizing surfaces. These surfaces may be solely vertical stabilizing fins as on the Bell Model 206 or a swept vertical extension of the tail boom as on the Hiller Model FH1100. The Hiller FH1100 tail surface houses the tail rotor drive shaft and the tail rotor output gearbox.
(1) For vertical stabilizers, the airloads may be assumed independent of the tail rotor thrust.
(ii) For vertical stabilizers that house the tail rotor output gearbox, such as the Hiller Model FH1100, the tail surface air loads will add to or subtract from the tail rotor thrust according to the flight condition under consideration.
Par 140 187
NOTE: For one example: At stabilized yaw to the right (left pedal depressed to limit) (§ 27.351(b)(2)), the tail rotor thrust moment should equal the restoring moment of the tail boom, vertical stabilizer, and main rotor torque. As stated by § 27.351(b)(3), the tail rotor thrust moment then is added to the vertical stabilizer restoring moment. The addition of tail rotor thrust (§ 27.351(b)(3)) and vertical stabilizer load is generally one of the critical design conditions for the fuselage/tail boom.
(iii) For vertical stabilizers or fins that have an offset incidence angle with respect to the rotorcraft axis, the vertical fin moment is added, or subtracted as applicable, to the tail rotor thrust moment. The condition stated in § 27.351(b)(1) may result in adding the fin load to the tail rotor thrust.
(iv) Low airspeed maneuvers, such as sideward, rearward, and hover turns over a spot, typically impose insignificant aerodynamic loads on the fuselage and/or tail boom. The aerodynamic loads at VH or VNE, whichever is required, are generally the significant aerodynamic design loads.
(v) A rational logical assessment of the various yaw conditions may be used to reduce the load derivation and analysis workload for critical rotorcraft design conditions.
(vi) The rotorcraft structure should be analyzed and/or tested for loads derived from the critical design conditions.
(vii) A simple structural design envelope may be derived from these design data. If the right or left yaw limits are not very different, common and conservative design limits may be used. A sample yaw/forward speed diagram, as derived from design analysis of the characteristics of a hypothetical rotorcraft, is presented in Figure 140-1. A table of values would also suffice. This figure reflects characteristics which include a 90° yaw when the directional control inputs are applied at low airspeeds (up to 0.6 VNE) and 15° yaw when they are applied at the lesser of VNE or VH, with a straight line variation from 0.6 VNE to VH or VNE. The rotorcraft does not need to be capable of attaining the 90° and 15° yaw. They should be considered as the maximum sideslip limits.
188 Par 140
90°
YAW DEGREES (LONGITUDINAL AXIS) → 15° MAX.
0°
0.6 VNE AIRSPEED
LESSER OF
VA OR VNE FIGURE 140-1. SAMPLE YAW/FORWARD SPEED DIAGRAM Par 140 189