(v) The analysis must include appropriate special factors, casting factors, bearing factors, and fitting factors prescribed by §§ 27.619, 27.621, 27.623, and
27.625, respectively. The fitting factor of 1.15 must be applied in the analysis of the tail rotor installation.
156A. § 27.401 (Amendment 27-27) AUXILIARY ROTOR ASSEMBLIES.
a. Explanation. Amendment 27-27 removed this section since the requirements are adequately addressed in §§ 27.337, 27.339, and 27.341.
b. Procedures. The policy material pertaining to this section is retained as supplemental information.
157. § 27.403 AUXILIARY ROTOR ATTACHMENT STRUCTURE.
a. Explanation.
(1) The auxiliary rotor attachment structure(s), which is considered to include gearboxes, must be designed to withstand design limit loads that occur in flight and on landing. These design loads that generally consist of the following must be established for the particular flight and landing condition under consideration.
(1) Inertia loads generated by linear and angular accelerations of the auxiliary rotors and their gearboxes, combined with--
(il) Thrust and torque loads developed by the auxiliary rotors.
The linear and angular acceleration loads imposed by the weight of the tail rotor and gearbox are generally derived from airframe loads data. Thrust and torque output of the tail rotor are derived during external aerodynamic and landing loads development for pertinent flight and landing conditions.
(2) General rules related to proof of structure loads and factor of safety are §§ 27.307, 27.301, 27.303, and 27.305.
b. Procedures.
(1) The angular and linear acceleration loads combined with appropriate tail rotor thrust and torque for the critical conditions shall be imposed on the tail rotor gearbox mount lugs, the airframe mounting structure, and the attaching hardware.
(2) The yaw and maximum power climb conditions are generally critical.
Landing and maneuvering conditions with and without power may also impose high inertia and rotor thrust and torque loads on the attachment structure.
Par 156 207
(3) The derivation of the loads and conditions is too extensive to include here.
Additional information can be found in the U.S. Army Material Command Report AMCP 706-201, "Engineering Design Handbook: Helicopter Engineering, Part One, Preliminary Designi 157A. § 27.403 (Amendment 27-27) AUXILIARY ROTOR ATTACHMENT STRUCTURE.
a. Explanation. Amendment 27-27 removed this section since the requirements are adequately addressed in §§ 27.337, 27.339, 27.341.
b. Procedures. The policy material pertaining to this section is retained as supplemental information.
158. § 27.411 GROUND CLEARANCE: TAIL ROTOR GUARD.
a. Explanation.
(1) The rule requires specific protection to prevent the tail rotor from contacting the landing surface during a normal landing if it is possible that the tail rotor will contact the surface. The rule states that it must be impossible for the tail rotor to contact the surface during a normal landing.
(2) If a guard is required, the guard and its supporting structure must withstand suitable design loads.
(3) Section 27.501(c)(1) contains skid landing gear drag requirements that may be applied to the guard design loads.
b. Procedures.
(1) The applicant may submit sketches or drawings showing probable clearance with typical level landing surfaces during normal landings. Typical attitudes such as nose-high autorotation, or autorotation with power-on landing, or other possible tail-low attitudes should be investigated. If the drawings or sketches reveal that it is not likely the tail rotor will contact the landing surface, this minimum clearance with the landing surface may be confirmed during official FAA/AUTHORITY flight tests, such as HV and landing tests. The clearance may be confirmed by having a frangible device of suitable length (i.e., a balsa wood dowel) extending beyond the guard and attached to the tail rotor guard or other appropriate fuselage part. If the device is not damaged, broken, or no contact is made with the surface, compliance has been demonstrated.
(2) If it is possible for the tail rotor guard to contact the landing surface, suitable design loads must be established for the guard. ANC-2a dated March 1948, "ANC Bulletin Ground Loads," Paragraph 6.4, entitled "Tail Bumper Criteria," is an acceptable 208 Par 157
means of deriving the rotorcraft kinetic energy that shall be absorbed by the guard.
This method is noted here for convenience.
The tail rotor guard shall be able to absorb the kinetic energy of the rotorcraft in its most unfavorable CG position in the tail-down landing attitude. The kinetic energy that the tail rotor guard should be capable of absorbing may be determined by the following:
WV≤ KE = 2g (Ky +133) where-- Vs = vertical speed fusec, derived from § 27.725(a) Ky = pitching radius of gyration - ft from pitching axis 1B = distance from most critical CG location to the guard or bumper contact point - ft g = 32.2 ft/sec W= gross weight less rotor lift from § 27.473(a) - Ibs
(il) Other, more recent, analytical techniques (most utilizing computer programs) may, of course, be used rather than the ANC-2a means after proper substantiation for applicability and validity.
(iii) The tail rotor guard should not fail when the limit and ultimate load, which is derived from a combination of the limit kinetic energy and the guard resulting limit deflection required to dissipate the energy, is imposed on the guard and the rotorcraft tail (see § 27.305).
(3) Substantiation of the guard, skid, or bumper for the design loads derived may be accomplished by test or analysis as stated in § 27.307(a).
(4) Several rotorcraft tail rotor guards are installed solely for the protection of ground personnel from the rotating tail rotor. For guards installed for this purpose, the applicant should use prudent and reasonable design loads and features. Such guards should not present a hazard to the rotorcraft because of its design features.
159. § 27.413 STABILIZING AND CONTROL SURFACES.
a. Explanation. Minimum design loads are specified for stabilizing as well as control surfaces.
(1) Paragraph (a) of the rule requires application of minimum empirical design loads, application of critical maneuvering loads, and application of critical maneuvering loads combined with vertical gust loads (30 feet per second or 17.8 knots per § 27.341).
Par 158 209
(2) Paragraph (b) requires load distributions that closely simulate actual pressure distributions. Both spanwise and chordwise distributions are intended.
(3) These surfaces are used for stability and control thereby hopefully extending the CG range and increasing the airspeed of modern designs.
(4) To "closely simulate actual pressure condition" on the surfaces, unsymmetrical loads are also required on horizontal surfaces. An arbitrary distribution, if conservative, may be used.
(5) It is noted § 27.571 requires fatigue substantiation of the flight structure which will include control and stabilizing surfaces.
(6) If the surface is controllable, a proof and operation test of the surface control system is required by §§ 27.681 and 27.683.
b. Procedures. Modern rotorcraft designs have generally employed a fixed or a wholly movable, not split or divided, stabilizing or control surface.
(1) Design Loads.
Limit loads of 15 pounds per square foot will apply up to approximately a 90-knot design airspeed. Above a 90-knot design airspeed (1.11VNE), the coefficient (Cy = 0.55) imposes higher limit loads on the surface. The coefficient ON is assumed normal to the chordline of the section.
(Ii) In addition, combined maneuvering and vertical up or down gust loads may impose the highest limit loads on the control surfaces of rotorcraft. This is attributed to the change in angle of attack and change in resultant airspeed.
(ili) The applicant may choose to derive the limit loads using maximum aerodynamic coefficients for the surface under consideration at the maximum design airspeed combined with a 17.8-knot gust. This would be acceptable provided these design loads exceed the minimum loads derived from a ON = 0.55 at design airspeed or exceed 15 pounds per square foot load on the surface.
(2) The load distribution on the surface should closely simulate actual pressure distributions.
210 Par 159
(i) The spanwise load may be rectangular, or other acceptable conservative distributions may be used. The method developed by O. Schrenk in NACA TM 948, 1940, is an acceptable method for approximation of spanwise distribution.
NOTE: The method is valid for aspect ratios of 5 through 12 and for rectangular planforms such as used on rotorcraft, other planforms may be acceptable as prescribed in the TM.
(ii) The chordwise distribution appropriate for the aerodynamic shape or a conservative distribution should be used.
(iii) The flight load survey conducted under § 27.571 may be used to confirm design parameters and possible load distribution data. On controllable surfaces, the pitching moment (control loads) may be measured for fatigue substantiation of the control system. The control stabilizing surfaces may be subject to loads measurement and possible fatigue tests for fatigue substantiation also.
(3) Proof of the structure for the required loads is specified in §§ 27.301,
27.303, 27.305, and 27.307. Tests or analysis may be used as prescribed. If analysis is used, fitting factors and other appropriate factors prescribed by the rules of §§ 27.625, 27.621, and 27.623 will be required in the analysis.
159A. § 27.413 (Amendment 27-27) STABILIZING AND CONTROL SURFACES.
a. Explanation. Amendment 27-27 removed this section since the requirements are adequately addressed in §§ 27.337, 27.339, and 27.341.
b. Procedures. The policy material pertaining to this section is retained as supplemental information especially as reference material for Paragraph 139 (§ 27.341) of this document.
160. § 27.427 (Amendment 27-27) UNSYMMETRICAL LOADS.
a. Explanation. Amendment 27-26 added the standard and Amendment 27-27 amended it. Minimum unsymmetrical design loads are specified for horizontal tail surfaces and also vertical tail surfaces whenever they support the horizontal tail surfaces.
(1) Loads are derived by rational analysis, or for earlier certification bases, the prescribed empirical loads of § 27.413 may be used. Section 27.413 was removed by Amendment 27-27 since the requirements are adequately addressed in §§ 27.337,
27.339, and 27.341.
Par 159 211
(2) Rational loads, appropriate for the aerodynamic surfaces, should be distributed according to the standard.
(3) When vertical tail surfaces support the horizontal tail surfaces, the vertical tail surfaces and supporting surfaces are required to support the critical combination of vertical and horizontal surface loads.
b. Procedures. Two basic loading conditions are required by § 27.427 for each of the two basic empennage configurations.
(1) Horizontal surfaces supported by the tail boom or fuselage. Structural substantiation should be provided for all six combinations shown in Figure 160-1. All of these empirical loading distributions should be used unless rational analysis shows one or more of each set of conditions to be non-critical or equal or more realistic distributions are substantiated. Rectangular spanwise air load distribution should be used unless more rational distribution is substantiated. If end plates are used, the air loads should be distributed accordingly.
First unsymmetrical loading condition:
(A) 100 percent of the flight load is applied to one side of the plane of symmetry; and 0 percent of the flight load is applied to the other side of the plane of symmetry.
(B) For surfaces with end plates or other similar devices, the load distribution will be changed accordingly.
(i) Second unsymmetrical loading condition:
50 percent of the flight load is applied to one side of the plane of symmetry acting up;
and 50 percent of the flight load is applied to the other side of the plane of symmetry acting down.
(2) Horizontal surfaces supported by a vertical surface. Structural substantiation should be provided for all six combinations shown in Figure 160-2. All of these empirical loading distributions should be used unless rational analysis shows one or more of each set of conditions to be non-critical or equal or more realistic distributions are substantiated. Rectangular spanwise air load distribution should be used unless more rational distribution is substantiated. If end plates are used, the air loads should be distributed accordingly.
First unsymmetrical loading condition:
100 percent of the flight load is applied to one side of the plane of symmetry; and O percent of the flight load is applied to the other side of the plane of symmetry.
212 Par 160
(ii) Second unsymmetrical loading condition:
50 percent of the flight load is applied to one side of the plane of symmetry acting up;
and 50 percent of the flight load is applied to the other side of the plane of symmetry acting down.
Par 160 213
Figure 160-1. (View Looking Forward) 214 Par 160
Figure 160-2. (View Looking Forward) Par 160 215
161.-169. RESERVED.
Intentionally Left Blank 216 (thru 224) Par 161
SECTION 10. GROUND LOADS
170. $ 27.471 GENERAL.
a. Explanation. This regulation specifies that limit ground loads must be considered which are:
(1) External loads caused by landing (ground) conditions for skid and wheel landing gear equipped rotorcraft and by ground taxiing loads as specified in § 27.235 for wheel landing gear equipped rotorcraft.
(2) Loads considering the rotorcraft structure as a rigid body.
(3) Loads in equilibrium with linear and angular inertia loads.
(4) The critical center of gravity "must be selected so that the maximum design loads are obtained in each landing gear element."
b. Procedures.
(1) The standards to be considered are specified in §§ 27.473 through 27.505.
These associated standards cover landing gear arrangements, landing conditions, and ground loading conditions (for wheel landing gear rotorcraft).
(2) Drop tests may be used to verify landing load factors. (See Paragraph 299 of this document.)
(3) The application of the design loads derived from the landing load factors will be as specified for each element affected by landing or ground loading conditions (for wheel landing gear rotorcraft).
(4) During the applicant's flight test program, the landing load factors for skid and wheel landing gear rotorcraft and taxiing load factors for wheel landing gear rotorcraft are monitored to assure the design load factors used are adequate. See Paragraph 97 of this document for § 27.235 policy.
171. § 27.473 (Amendment 27-2) GROUND LOADING CONDITIONS AND ASSUMPTIONS.
a. Explanation. The rotorcraft is to be designed for the maximum weight. A rotor lift of two-thirds of the design maximum weight may be used. The minimum limit landing load factor is determined by the drop tests of § 27.725.
Par 170 225
b. Procedures. Loads for the landing conditions are derived considering mass (equal to the maximum weight) and rotor lift (equal to two-thirds of the maximum weight) acting through the center of gravity throughout the landing impact. Unbalanced external loads resulting from asymmetric loading conditions are reacted as specified in the individual subparagraphs. The rotorcraft must be substantiated for ultimate landing loads by either test or analysis utilizing an ultimate load factor of 1.5 applied to the limit load factor of not less than that substantiated under § 27.725.
172. § 27.475 TIRES AND SHOCK ABSORBERS.
a. Explanation. This section specifies the tire and shock absorber position to be used in ground load derivations.
b. Procedures. Ground loads are to be derived with the tires in static (1g) position and the shock absorbers "in their most critical position." The determination of the "most critical positioni for the shock absorbers generally requires a load versus deflection test or analysis of the shock absorber system and a determination of the effect of both load and deflections on the shock absorber, attachment structure, and substructure designed by ground loads.
173. § 27.477 LANDING GEAR ARRANGEMENT.
a. Explanation. This section specifies the individual standards to be used for ground load conditions for rotorcraft having two wheels aft and one or more wheels forward of the center of gravity.
NOTE: § 27.497 gives ground loading conditions for landing gear with tail wheels, and § 27.501 gives ground loading conditions for landing gear with skids.
b. Procedures. The ground loading conditions of §§ 27.235, 27.479 through
27.485, and 27.493 will be used for rotorcraft having two wheels aft and one or more wheels forward of the center of gravity. This includes forward wheels on separate axles.
174. § 27.479 LEVEL LANDING CONDITIONS.
a. Explanation. This section provides explicit level landing load criteria for landing gear with two wheels aft and one or more wheels forward of the center of gravity.
(1) Level landings--
(i) Each wheel contacting the ground simultaneously; and
(ii) Aft wheels contacting the ground with forward wheels just clear of the ground.
226 Par 171