10-24 Table 10-1. Static Test Requirements TC Basis Airplanes Category G Factor Weight Factor (pounds) Fitting Factor Harness Factor (40%) Static Test Minimum Load (pounds) Effective 09/14/88 and on N, U, A 9 215 1.33 0.4 1,029 Effective 09/14/69 N 9 170 1.33 0.4 814 U, A 9 190 1.33 0.4 910 Pre 09/14/69 N 9 170 1.15 0.4 704 U, A 9 190 1.15 0.4 787 Helicopter Pre-12/16/84 N 4 170 1.15 0.6 469 Helicopter Post-12/16/84 Pre-12/13/89 N 4 170 1.33 0.6 543 Note 1: N = Normal, U = Utility, A = Acrobatic Note 2: Airplane seat/restraint systems type certificated after September 14, 1988, must undergo dynamic testing, as prescribed by 14 CFR § 23.562, which is not covered in this chapter.
Table 10-2. Calculated 1/Cosine Values Degrees 5 10 15 20 25 30 35 40 50 60 1/Cos Multiplier 1.004 1.015 1.035 1.064 1.103 1.155 1.221 1.305 1.556 2.0
10-25 Figure 10-20. Vertical Angle Fig ure 10-21. Horizontal Angle
10-26 Section 4. Installation and Inspection Checklists
10.21 General. The following checklists are not all-inclusive but may provide a quick reference for factors to consider when installing retrofit shoulder harnesses and for establishing instructions for continued airworthiness (ICA) of retrofit harness installations. If available, the manufacturer’s instructions take precedence over this AC.
10.21.1 Shoulder Harness Installation Checklist.
1. Locate potential attach points.
2. Evaluate the geometry of attach points in relation to the occupant and determine the best harness configuration. Short belt lengths are desirable.
3. Ensure that the configuration will allow unimpeded egress for all occupants.
Single-point release is mandatory. There should be a means to secure belts and harnesses when not in use to avoid interfering with operation of the airplane or egress from it.
4. Restraints must allow crewmembers to perform all necessary flight operation functions while seat belts and harnesses are fastened.
5. Utility and acrobatic category airplane restraints must accommodate an occupant wearing a parachute.
6. If retractors will be used, ensure that mounting will provide straight-line entry and exit of webbing to prevent binding or frictional drag. Retractor loading should not impose bending forces upon retractor mounting brackets.
7. If harness installation will impose loads on the seat back or seat attachment, additional evaluation will be needed for structural integrity.
8. Refer to the aircraft type certificate (TC) to find the certification date and basis to establish minimum static load requirements. Determine the feasibility of performing static tests or stress analysis. Static testing on operational aircraft is not recommended.
9. Select only restraints that meet OEM, TSO, PMA, or other established industry standards or specifications.
10. Install restraints using AN, MS, NAS, or other acceptable aircraft hardware with adequate strength properties.
11. Perform a check to ensure all components function properly.
12. Complete record entries as required, including FAA Form 337, logbook, W&B, and equipment list.
10.21.2 Shoulder Harness Inspection Checklist. Inspect restraint system for condition and function at each annual or each required inspection of cabin or flight deck equipment. If questions arise regarding any of the conditions listed below, contact the restraint manufacturer for specific limits.
10-27
10.21.2.1 Inspect stitching on webbing for broken or missing stitches.
10.21.2.2 Inspect webbing for fraying, fading, or cuts. Fraying that causes binding in the retractor is excessive. Fading caused by exposure to sunlight or chemicals may indicate a reduction in strength.
10.21.2.3 Ensure that TSO, PMA, OEM, or other required identification tags are present and legible on each belt assembly. Tags may not be required for harnesses manufactured prior to March 27, 1987. Contact the aircraft or restraint manufacturer for specific requirements.
10.21.2.4 If so equipped, check the harness post on the lap belt to make sure the nylon bushing or grommet is present and functional to provide positive harness end fitting engagement. Do not replace the bushing with nylon bundle ties.
Contact the belt manufacturer for replacement bushings/grommets and instructions.
10.21.2.5 Check the belt buckle for latching and release functions.
10.21.2.6 Check the retractors to ensure that locking mechanisms engage when webbing is positioned at the normal operating length. Inertia reels should lock when the webbing is accelerated quickly out of the reel. Automatic locking retractors should lock at approximately 1-inch increments as the webbing retracts back into the reel.
10.21.2.7 Inspect buckles, connectors, and fittings for corrosion, cracks, or other damage. Check mounting hardware for security and ensure that airframe attachment of end fittings self-align and do not bind.
10.21.2.8 Inspect quick release end fittings for cotter pins.
10.21.2.9 If equipped with a manual locking inertia reel, check for proper operation and condition.
11-1 CHAPTER 11. AIRCRAFT BATTERY INSTALLATIONS Section 1. General
11.1 Purpose. This chapter contains structural and design considerations for the fabrication of aircraft battery installations.
11.2 Hazards and Warnings: Handling Precautions. Serious injury can result from carelessness while handling and working with batteries. Failure to heed these warnings could result in serious injury or death.
11.2.1 All tools must be insulated.
11.2.2 Care must be taken with all metal items, including clothing items such as belt buckles, zippers, metal fasteners, and wallet chains as well as jewelry items such as rings, watches, bracelets, and necklaces. All metal or conductive articles should be removed from your person when handling batteries.
11.2.3 Wear protective clothing and eye protection. The electrolyte can cause burns if in contact with skin or eyes. Do not touch eyes, nose, or mouth after handling batteries or acid.
11.2.4 Do not smoke or hold naked flames near batteries on charge. If allowed to accumulate in a confined space, the gases emitted during charge could cause an explosion. To prevent the accumulation of hydrogen gas in the manifold, do not charge a flooded electrolyte or vented battery on the bench with the cover on.
11.2.5 Do not service flooded or vented lead-acid and nickel-cadmium batteries in the same shop area as cross contamination of acid and alkaline electrolytes may happen.
11.2.6 Always pour acid into water; never pour water into acid.
11.2.7 Do not use petroleum spirits, trichloroethylene, or other solvents.
11.2.8 Know the location and use of the emergency eyewash and shower nearest the battery charging area.
11.3 Additional References (current editions).
• AC 20-106, Aircraft Inspection for the General Aviation Aircraft Owner.
• AC 43-4, Corrosion Control for Aircraft.
• AC 120-27, Aircraft Weight and Balance Control.
• Civil Air Regulation (CAR) 6, Rotorcraft Airworthiness; Normal Category.
• FAA-H-8083-1, Aircraft Weight and Balance Handbook.
• FAA-H-8083-19, Plane Sense General Aviation Information.
11.4 Location Requirements. The battery installation and/or its installation should provide:
11-2
11.4.1 Accessibility for Battery Maintenance and Removal. The installation should ensure that the battery could be easily installed or removed and serviced without removing seats, fairings, etc.
11.4.2 Protection from Engine Heat. If installed in the engine compartment, the battery should be protected from extreme heat both during engine operation and after the engine has been shut down. This kind of protection can be provided by a source of cooling air to the battery box or additional thermal protection around the battery. Care should be taken not to interfere with the flow of engine-cooling air.
11.4.3 Protection from Mechanical Damage. Vibration and other shock loads are a major cause of short battery life. Install the battery in a location that will minimize damage from airframe vibration and prevent accidental damage by passengers or cargo.
11.4.4 Passenger Protection. Ensure that the battery is enclosed within a container/box so that passengers/crew are protected from any fumes or electrolytes that may be spilled as a result of battery overheating, minor crash, or unintentional inverted flight.
11.4.5 Airframe Protection. To minimize damage to adjacent metal structures, fabric coverings or electrical equipment can be accomplished by properly locating battery drains and vent discharge lines and adequately venting the battery compartment. To protect the airframe structure and fluid lines, apply asphaltic or rubber-based paint to the areas adjacent to and below the battery or battery box.
11.5 Aircraft Storage Battery Design and Installation.
11.5.1 Lead Acid.
11.5.1.1 Each aircraft storage battery, whether approved to a Technical Standard Order (TSO) or not, must be designed as required by regulation and installed as prescribed by the manufacturer.
11.5.1.2 No explosive or toxic gases emitted by any battery in normal operation, or as the result of any probable malfunction in the charging system or battery installation, may accumulate in hazardous quantities within the airplane.
11.5.1.3 Corrosive fluids or gases that may escape from the battery may damage surrounding structures or adjacent essential equipment.
11.5.2 Nickel Cadmium.
11.5.2.1 Each aircraft storage battery, whether approved to a TSO or not, must be designed as required by regulation and installed as prescribed by the manufacturer.
11.5.2.2 Safe cell temperatures and pressures must be maintained during any probable charging and discharging condition. No uncontrolled increase in cell
11-3 temperature may result when the battery is recharged (after previous complete discharge):
• At maximum regulated voltage or power;
• During a flight of maximum duration; and
• Under the most adverse cooling condition likely to occur in service.
11.5.2.3 Compliance with paragraph 11.5.2.2 must be shown by tests unless experience with similar batteries and installations has shown that maintaining safe cell temperatures and pressures presents no problem.
11.5.2.4 No explosive or toxic gases emitted by any battery in normal operation, or as the result of any probable malfunction in the charging system or battery installation, may accumulate in hazardous quantities within the airplane.
11.5.2.5 Corrosive fluids or gases that may escape from the battery may damage surrounding structures or adjacent essential equipment.
11.6 Duplication of the Manufacturer’s Installation. The availability of ready-made parts and attachment fittings may make it desirable to consider the location or type of installation, or both, selected and designed by the airframe manufacturer. Appreciable savings in time and work may be realized if previously approved data and/or parts are used.
11.7 Other Installations. If the battery installation has not been previously approved, or if the battery is to be installed or relocated in a manner or location other than provided in previously approved data, perform static tests on the completed installation as outlined in Chapter 2, Structural Data. Because of the concentrated mass of the battery, the support structure should also be rigid enough to prevent undue vibration or undue shock, which may lead to early structural failure.
11.8 Delivery Inspection. When the battery is unpacked, a thorough inspection should be made to ensure that no damage occurred during shipment. Inspect the shipping container as well as the battery. Before putting the battery into service, perform a safety check by following these points carefully.
11.8.1 Damage. See if any liquid has spilled into the shipping container. This may indicate that a cell is damaged. Check for dented, cracked, or discolored areas on the sides and bottom of the battery case. Check for cracked cell cases or covers. Do not place a damaged battery into service.
11.8.2 Shorting Straps. Some nickel-cadmium batteries are shipped with shorting devices across the main power receptacle output terminals. Before subjecting a battery to electrical service, this device must be removed.
11-4
11.8.3 Electrical Connections. Test all terminal hardware to ensure tightness. Poor electrical contact between mating surfaces may reduce discharge voltage, cause local overheating, and damage the battery.
Note: Before charging the battery, read and become familiar with the manufacturer’s charge procedures.
11.9 Battery Installation and Removal. The following instructions are generic. Refer to the airframe manufacturer’s maintenance manuals or Supplemental Type Certificate (STC) for instructions specific to a particular aircraft model.
11.9.1 Removal.
1. Set the master switch to the OFF position and tag the switch.
2. Disconnect any external power supply.
3. Open battery compartment access panels.
4. Disconnect the battery quick disconnect plug or remove terminal bolts and disconnect battery cables from battery terminals. Always disconnect the ground cable first and install the ground cable last.
5. Disconnect battery ventilation tubes, if any.
6. Unlock battery hold-down clamps or remove battery hold-down bars. Disengage the battery.
7. Carefully remove the battery.
WARNING: Batteries are heavy. Use appropriate lifting devices or equipment.
Use battery handles where provided.
11.9.2 Installation.
1. Inspect the battery for damage. Cracks in metal or plastic containers are not permitted. Dents in metal containers that impinge on the interior plastic container are not acceptable.
2. Set master switch to the OFF position and tag (explain what should be on the tag “Do not turn on master switch”).
3. Disconnect any external power supply and tag (explain what should be on the tag “Do not connect external power”).
4. Open battery compartment access panels.
5. Ensure the battery container or tray is clean and dry. Treat and paint any corrosion areas.
6. Install the battery in the battery container or tray.
WARNING: Batteries are heavy. Use appropriate lifting devices or equipment.
Use battery handles where provided.
11-5
7. Engage battery hold-down hardware, torque, and safety wire per airframe manufacturer’s maintenance manual.
8. Connect battery vent tubes.
9. Connect the battery quick disconnect plug and any auxiliary connector, or for ring terminals, install with a bolt and lock washer. Torque terminal bolts as recommended by the manufacturer.
10. Replace the electrical compartment access panel.
11. Perform an operational test.
12. Update aircraft Weight and Balance (W&B) data, if necessary.
13. Update the equipment list, if applicable.
14. Make a logbook entry with the battery serial number and date of installation.
Figure 11-1. Typical Battery Installation in the Aircraft
11-6 Section 2. Lead-Acid Battery Installations
11.10 General. In a lead-acid battery, the voltage will slowly drop as opposed to a nickel-cadmium battery. These batteries are typically less expensive, do not require temperature sensor monitoring, require virtually no maintenance, and, when unable to meet the manufacturer’s capacity requirements, are simply removed and replaced.
11.11 Battery Box. The battery box should have an open drain in case the electrolyte overflows. The box should be vented to prevent an accumulation of flammable hydrogen gas.
11.12 Securing the Battery. Install the battery in such a manner as to hold the battery securely in place without subjecting it to excessive localized pressure, which may distort or crack the battery case. Apply Par-Al-Ketone, heavy grease, or other comparable protective coating to battery cables terminal nuts/connectors. Ensure that proper torque is applied to the terminal nuts/connectors. Do not over tighten terminal nuts, which may result in fracturing of the terminal posts. Provide adequate clearance between the battery and any bolts or rivets, or both, that may protrude into the battery box or compartment.
WARNING: When installing or removing a battery, wear safety glasses and take special care to ensure that no sparks are created by tools or loose jewelry that provide a short to ground. Always remove the ground cable first and install it last.
If possible, attach the ground cable to the frame of the battery compartment. Do not lift the battery by its vent tubes, receptacles, or terminals.
11.13 Sump Jar. Lead-acid batteries are often installed with a sump jar in the exhaust vent that neutralizes vented acid fumes to protect the airframe from corrosive battery acid. If installed, the sump jar should have a capacity of approximately one pint. The jar should contain a 1/2-inch thick pad saturated with a five-percent solution of sodium bicarbonate (baking soda) in water or about a 3/8 inch of dry sodium bicarbonate. The inlet tube carrying fumes to the sump should extend into the jar about 1 inch from the lid (see Figure 11-2, Typical Battery Installation With Sump Jar).
11-7 Figure 11-2. Typical Battery Installation With Sump Jar
11.14 Venting. Provide suitable venting to the battery compartment to prevent the accumulation of hydrogen gas expelled during operation.
Note: Valve-regulated lead-acid batteries can use the same ventilation system as the original nickel-cadmium battery.
11.14.1 Manifold Type. In this type of venting, one or more batteries are connected via the battery manifold(s) or battery box vents to a hose or tube manifold system as shown in Figure 11-3, Battery Ventilation System. Fasten such hoses securely to prevent shifting and maintain adequate bend radii to prevent kinking.
11.14.1.1 The upstream side of the system is connected to a positive pressure point on the aircraft, and the downstream side is usually discharged overboard to a negative pressure area. It is advisable to install a battery sump jar on the downstream side to neutralize any corrosive vapors that may be discharged.
11.14.1.2 When selecting these pressure points, select points that will always provide the proper direction of airflow through the manifold system during all normal operating attitudes. Reversals of flow within the vent system should not be permitted when a battery sump jar is installed, as the neutralizing agent in the jar may contaminate the battery’s electrolyte.
11-8 Figure 11-3. Battery Ventilation System
11.14.2 Free Airflow Type. Battery cases or boxes that contain louvers may be installed without an individual vent system, provided that:
• The compartment in which the battery is installed has sufficient airflow to prevent the accumulation of explosive mixtures of hydrogen;
• Noxious fumes are directed away from occupants; and
• Suitable precautions are taken to prevent corrosive battery fluids or vapors from damaging the surrounding structure, covering, equipment, control cables, wiring, etc.
11.15 Drains. Position battery compartment drains so that they do not allow spillage to come in contact with the aircraft during either ground or flight attitudes. Route the drains so they have a positive slope without traps. Drains should be at least a 1/2 inch in diameter to prevent clogging.
11.16 Electrical Installation. Electrical equipment, controls, and wiring must be installed so that operations of any one unit or system of units will not adversely affect the simultaneous operation of any other electrical unit or system essential to safe operation.
Any electrical interference likely to be present in the airplane must not result in hazardous effects upon the airplane or its systems.
11.16.1 Cables/Connectors. Use cables and/or connectors that are adequately rated for the current demand and are properly installed. Refer to AC 43.13-1, Acceptable Methods, Techniques, and Practices—Aircraft Inspection and Repair, Chapter 11, Aircraft