Par 2-7 Page 29
2. For flight altitudes above 8,000 ft MSL, the recommended wait time is at least 24 hours after any SCUBA diving. (See AIM paragraph 8-1-2, subparagraph d2.)
(5) What to Do If You Suspect DCS in Flight.
(a) Put on your oxygen mask immediately and switch the regulator to 100 percent oxygen.
(b) Begin an emergency descent and land as soon as possible. Even if the symptoms disappear during descent, you should still land and seek medical evaluation while continuing to breathe oxygen.
(c) If one of your symptoms is joint pain, keep the affected area still; do not try to work pain out by moving the joint around.
(6) Medical Treatment. A mild case of the bends may disappear during descent from high altitude. However, it still requires medical evaluation. If the signs and symptoms persist during descent or reappear at ground level, it may be necessary to receive hyperbaric oxygen treatment immediately. This involves 100 percent oxygen delivered in a high-pressure chamber.
WARNING:
Neurological DCS, “the chokes,” and skin manifestations (mottled or marbled skin lesions) are very serious and potentially fatal if untreated.
(7) Things to Remember about DCS.
(a) Altitude DCS is a potential risk every time you fly in an unpressurized aircraft above 18,000 ft, and at lower altitudes if you SCUBA dive prior to the flight.
(b) Be familiar with the signs and symptoms of altitude DCS and monitor all aircraft occupants, including yourself, any time you fly an unpressurized aircraft above 18,000 ft.
(c) Avoid unnecessary strenuous physical activity prior to flying an unpressurized aircraft above 18,000 ft and for 24 hours after the flight.
(d) Even if you are flying a pressurized aircraft, altitude DCS can occur as a result of sudden loss of cabin pressure (in-flight rapid decompression).
(e) Following exposure to an in-flight rapid decompression, do not fly for at least 24 hours. In the meantime, remain vigilant for the possible onset of delayed symptoms or signs of altitude DCS. If you experience delayed symptoms or signs of altitude DCS, seek medical attention immediately.
Page 30 Par 2-7
(f) Keep in mind that breathing 100 percent oxygen during flight (ascent, en route, descent) without oxygen prebreathing prior to take off, does not prevent the occurrence of altitude DCS.
(g) Do not ignore any symptoms or signs that go away during the descent. In fact, this could confirm that you are actually suffering altitude DCS.
(h) Any case of altitude DCS should be medically evaluated as soon as possible, even if symptoms are mild or disappear on descent.
(i) If there is any indication that you may have experienced altitude DCS, do not fly again until you are cleared to do so by a physician familiar with and experienced with treatment of DCS. For questions about your continued eligibility for your airman medical certificate contact an FAA medical officer or your AME.
(j) Allow at least 24 hours to elapse between SCUBA diving or hypobaric (altitude) chamber exposure and flying.
(k) Be prepared for a future emergency by familiarizing yourself with the availability of hyperbaric chambers in your area of operations. However, keep in mind that not all of the available hyperbaric treatment facilities have personnel qualified to handle altitude DCS emergencies. To obtain information on location of hyperbaric treatment facilities capable of handling altitude DCS emergencies, call the Divers Alert Network at 919-684-9111.
f. Vision Deterioration. Vision has a tendency to deteriorate with altitude; smoking worsens this effect. A reversal of light distribution at high altitudes (bright clouds below the airplane and darker, blue sky above) can cause a glare inside the cockpit. Glare effects and deteriorated vision are enhanced at night when the body becomes more susceptible to hypoxia and can occur at altitudes as low as 5,000 ft MSL. In addition, the empty visual field caused by cloudless, blue skies during the day can cause inaccuracies when judging the speed, size, and distance of other aircraft. We recommend sunglasses to minimize the intensity of the sun’s ultraviolet rays at high altitudes.
2-8. FAA PHYSIOLOGICAL TRAINING. There are no specific requirements in 14 CFR part 91 or 125 for physiological training. However, § 61.31(g) requires the high-altitude training outlined in this AC. Also, 14 CFR parts 121 and 135 require flightcrew members that serve in operations above 25,000 ft MSL to receive training in specified subjects of aviation physiology.
None of the regulations include altitude chamber training. Although most of the subject material normally covered in physiological training concerns problems associated with reduced atmospheric pressure at high-flight altitudes, it covers other equally important subjects as well.
Such subjects of aviation physiology as vision, disorientation, physical fitness, stress, and survival affect flight safety and are normally present in a good training program.
a. FAA Civil Aerospace Medical Institute (CAMI) Aviation Physiology Course.
CAMI offers a 1-day aviation physiology course for FAA flightcrews, civil aviation pilots, and FAA AMEs. In addition to the basic academic contents, this course offers practical demonstrations of rapid decompression (8,000 to 18,000 ft MSL) and hypoxia (25,000 ft MSL)
Par 2-8 Page 31 in a hypobaric chamber. Additionally, the course features a practical demonstration of spatial disorientation in a spatial disorientation demonstrator.
(1) Requirements. Persons who wish to take this training must be at least 18 years of age, hold a current FAA Airman Medical Certificate, and not have a cold or any other significant health problem when enrolling for the course.
NOTE: Anyone can attend the training regardless of whether they are a pilot or not. However, trainees still must obtain a minimum of a Class III medical certificate in order to participate in the altitude chamber training.
(2) Scheduling. CAMI’s Airman Education Programs obtains a list of training dates from each base that are available to anyone interested in the training. Call 405-954-4837 to access these dates. Scheduling a training slot requires the following information:
• Full name,
• Date of birth,
• Name of organization (if applicable),
• Mailing address,
• Daytime phone number,
• Aircrew position or non-aircrew position, and
• All applicants that are not U.S. citizens must provide additional information (Security Clearance Request) found at http://www.faa.gov/pilots/training/airman_education/media/ SecurityClearanceRequest.doc.
(3) Submitting an Application. CAMI will mail a notification letter to you. The applicant should take the notification letter, along with a current medical certificate, to the training facility on the day of the training. For more information see the CAMI Web site at www.faa.gov.
b. Physiology of Flight Video Library. The FAA has developed a series of educational programs developed to address the human factors hazards of high-altitude flight. You may view these videos at http://www.faa.gov/pilots/training/airman_education/.
c. Airplane Upset Recovery. The FAA has developed a training aid on upset recovery and high-altitude operations. You can obtain the training aid at http://www.faa.gov/other_visit/ aviation_industry/airline_operators/training/media/Appendix_3-E_HighAltOperations.pdf.
2-9. HIGH-ALTITUDE SYSTEMS AND EQUIPMENT. Several systems and equipment are unique to aircraft that fly at high altitudes, and pilots should be familiar with their operation before using them. Before any flight, a pilot should be familiar with all the systems on the aircraft to be flown.
a. Turbochargers. Most light piston engine airplanes that fly above 25,000 ft MSL are turbocharged. Turbochargers compress air in the carburetor or cylinder intake by using exhaust gases from an engine-driven turbine wheel. The increased air density provides greater power and improved performance. Turbocharged engines are particularly temperature-sensitive.
Page 32 Par 2-9 Manufacturers often recommend increasing the fuel flow during climbs to prevent overheating. It is also important to cool the engine after landing. Allow the engine to idle for approximately 1 minute before shutting it down. This permits engine oil to flow through the system, cooling the engine while simultaneously cooling and lubricating the turbocharger. Light aircraft use one of two types of turbocharger systems.
(1) Normalized System. The first is the normalized system, which allows the engine to develop sea level pressure from approximately 29 inches of manifold pressure up to a critical altitude (generally between 14,000 and 16,000 ft MSL).
(2) Supercharger System. The second is the supercharger system, which is driven by the engine through a gear train at one, two, or variable speeds. It is a more powerful system that allows the engine to develop higher than sea level pressure (up to 60 in of manifold pressure) up to a critical altitude. To prevent overboosting at altitudes below the critical altitude, a waste gate is installed in the turbocompressor system to release unnecessary gases. The waste gate is a damper-like device that controls the amount of exhaust that strikes the turbine rotor. As the waste gate closes with altitude, it sends more gases through the turbine compressor, causing the rotor to spin faster. This allows the engine to function as if it were maintaining sea level or, in the case of a supercharger, above sea level manifold pressure. The three principal types of waste gate operations are manual, fixed, and automatic.
(a) Manual Waste Gate. Manual waste gate systems are common in older aircraft, but have been discontinued due to the additional burden on the pilot. Waste gates were often left closed on takeoff, resulting in an overboost that could harm the engine.
(b) Fixed Waste Gate. Fixed waste gates pose less of a burden on the pilot, but the pilot must still be careful not to overboost the engine, especially on takeoff, initial climb, and on cold days when the air is especially dense. This type of waste gate remains in the same position during all engine operations, but it splits the exhaust flow, allowing only partial exhaust access to the turbine. The pilot simply controls manifold pressure with smooth, slow application of the throttle to control against overboost. If overboost does occur, a relief valve on the intake manifold protects the engine from damage. This is not a favorable system due to fluctuations in manifold pressure and limited additional power from the restricted control over the exhaust flow.
In addition, the compressor can produce excessive pressure and cause overheating.
(c) Automatic Waste Gate. Automatic waste gates operate on internal pressure.
When internal pressure builds towards an overboost, the waste gate opens to relieve pressure, keeping the engine within normal operating limits regardless of the air density.
1. The pressure-reference automatic waste gate system maintains the manifold pressure set by the throttle. Engine oil pressure moves the waste gate to maintain the appropriate manifold pressure, thus reducing the pilot’s workload and eliminating the possibility of overboost. If the airplane engine is started and followed by an immediate takeoff, cold oil may cause a higher-than-intended manifold pressure. Allow the oil to warm up and circulate throughout the system before takeoff.
Par 2-9 Page 33
2. Compressor discharge air controls the density-reference waste gate system.
A density controller holds a given density of air by automatically adjusting manifold pressure as airspeed, ambient pressure, temperature, altitude, and other variables change.
b. Oxygen and Oxygen Equipment. Most high-altitude airplanes come equipped with some type of fixed oxygen installation. If the airplane does not have a fixed installation, portable oxygen equipment must be readily accessible during flight. The portable equipment usually consists of a container, regulator, mask outlet, and pressure gauge. A typical 22-cubic ft portable container will contain enough oxygen for approximately 1.5 hours at 18,000 ft MSL for four people. Aircraft oxygen is usually stored in high-pressure system containers of 1,800 to 2,200 pounds per square inch (psi). The container should be fastened securely in the aircraft before flight. When the ambient temperature surrounding an oxygen cylinder decreases, pressure within that cylinder will decrease because pressure varies directly with temperature if the volume of a gas remains constant. A drop in indicated pressure on a supplemental oxygen cylinder can be an indication that the oxygen supply has merely compacted (not necessarily a leak).
High-pressure oxygen containers should be marked with the psi tolerance (i.e., 1,800 psi) before filling the container to that pressure. Only oxygen that meets or exceeds the Society of Automotive Engineers (SAE) International Aerospace Standard AS8010 (as revised), Aviator’s Breathing Oxygen Purity Standard, should be used. To assure safety, periodic inspection and servicing should take place by a certified maintenance provide found at some fixed base operations and terminal complexes.
(1) Regulator and Mask Systems. Regulators and masks work on continuous flow, diluter demand, or pressure demand systems.
(a) Continuous Flow System. The continuous flow system supplies oxygen at a rate that may be controlled automatically or by the user. The mask is designed so the oxygen can be diluted with ambient air by allowing the user to exhale around the facepiece, and comes with a rebreather bag, which allows the individual to reuse part of the exhaled oxygen. Pilot masks sometimes allow greater oxygen flow than passengers’ masks, so it is important that pilots use the masks indicated for them. Although certificated up to 41,000 ft MSL, system capabilities require very careful attention when using continuous flow oxygen systems above 25,000 ft MSL.
(b) Diluter Demand and Pressure Demand Systems. Diluter demand and pressure demand systems supply oxygen only when the user inhales through the mask. An automix lever allows the regulators to automatically mix cabin air and oxygen or supply 100 percent oxygen, depending on the altitude. The demand mask provides a tight seal over the face to prevent dilution with outside air and can be used safely up to 40,000 ft MSL. Pilots who fly at those altitudes should not have beards and mustaches because air can easily seep in through the border of the mask. Pressure demand regulators also create airtight and oxygen-tight seals, but they also provide a positive pressure application of oxygen to the mask facepiece, which allows the user’s lungs to be pressurized with oxygen. This feature makes pressure demand regulators safe at altitudes above 40,000 ft MSL.
(2) Increased Fire Risk. Pilots should be aware of the increased danger of fire when using oxygen. Materials that are nearly fireproof in ordinary air may be susceptible to burning in
Page 34 Par 2-9 oxygen. Oils and greases may catch fire if exposed to oxygen, and therefore cannot be used for sealing the valves and fittings of oxygen equipment. Smoking during the use of any kind of oxygen equipment must also be strictly forbidden.
(3) Equipment Inspection. A certified maintenance provider must inspect the aircraft system, and a Department of Transportation (DOT)-approved facility must hydrostatic test the oxygen bottles, before use. Before each flight, the pilot should thoroughly inspect and test all oxygen equipment. The inspection should be accomplished with clean hands and should include a visual inspection of the mask and tubing for tears, cracks, or deterioration. The regulator should also be checked for valve and lever condition and positions. Also be sure to check the oxygen quantity as well as the location and function of oxygen pressure gauges, flow indicators, and connections. The mask should be donned and the system tested. After any oxygen use, verify that all components and valves are shut off.
c. Pressurization Systems. Cabin pressurization is the compression of air in the aircraft cabin in order to maintain a cabin altitude lower than the actual flight altitude. Because of the ever-present possibility of decompression, the aircraft still requires supplemental oxygen.
Pressurized aircraft meeting specific requirements of 14 CFR part 23 or 25 have cabin altitude warning systems, which activate at a cabin altitude of 10,000 ft. Pressurized aircraft meeting the more stringent requirements of part 25 have automatic passenger oxygen mask-dispensing devices that activate before exceeding 15,000 ft cabin altitude. It should be noted that some aircraft require that the flightcrew disable the automatic passenger oxygen mask-dispensing devices prior to landing at airports over 10,000 ft MSL to prevent inadvertent deployment when the cabin depressurizes at landing. The system is then re-armed after departure.
(1) Pressure Control. Turbine aircraft use a steady supply of engine bleed air for cabin pressurization. In the case of most pressurized light aircraft, the air supply is sent to the cabin from the turbocharger’s compressor or from an engine-driven pneumatic pump. In any case, an outflow valve regulates the flow of compressed air out of the cabin, which keeps the pressure constant by releasing excess pressure into the atmosphere. The cabin altitude selection can be manual, or if available, electronic. A gauge that indicates the pressure difference between the cabin and ambient altitudes helps the pilot to monitor the cabin altitude. A manually set backup control automatically controls the rate of change between these two pressures.
(2) Pressure Differentials. Each pressurized aircraft has a determined maximum pressure differential, which is the maximum differential between cabin and ambient altitudes that the pressurized section of the aircraft can support. The pilot must be familiar with these limitations, as well as the manifold pressure settings recommended for various pressure differentials. Some aircraft have a negative pressure relief valve to equalize pressure in the event of a sudden decompression or rapid descent to prevent the cabin pressure from becoming lower than the ambient pressure. Reducing exposure to low barometric pressure lowers the occurrence of decompression sickness and eliminates the need for an oxygen mask as a full-time oxygen source above certain altitudes. Many airplanes are equipped with automatic visual and aural warning systems that indicate an unintentional loss of pressure.
d. High-Altitude Components. Thin air at high altitudes has created a need for specialized aircraft components that are adapted to this environment.
Par 2-9 Page 35
(1) Magnetos. Thin air at high altitudes makes the unpressurized magneto susceptible to crossfiring. Therefore, we recommend the use of pressurized magnetos. Sealed caps and plugs that keep the electrodes contained within the body compose the high-tension pressurized system.
A pressure line extends directly from the turbodischarger to the magneto. Pressurized magnetos perform better at high altitudes where low pressure and cold atmosphere have a detrimental effect on electrical conductivity. Avoid flight above 14,000 ft MSL with an unpressurized magneto because of its higher susceptibility to arcing.
(2) Vacuum Pump. Another airplane component recommended for flight at high altitudes is the dry vacuum pump. Engine-driven wet vacuum pumps cannot create a sufficient vacuum to drive the gyros in the low air density found at high altitudes. Furthermore, oil contamination from the wet pump system, which uses engine oil for lubrication and cooling, can ruin gyros and rubber deicing boots. Dry vacuum pumps are lightweight, self-lubricating systems that eliminate oil contamination and cooling problems. These pumps can power either a vacuum or pressure pneumatic system, allowing them to drive the gyros, deice boots, and pressurize the door seals.
2-10. AERODYNAMICS AND PERFORMANCE FACTORS. Thinner air at high altitudes has a significant impact on an airplane’s flying characteristics because surface control effects, lift, thrust, drag, and horsepower are all functions of air density.
a. Aircraft Controls. The reduced weight of air moving over control surfaces at high altitudes decreases their effectiveness. As the airplane approaches its absolute altitude, the controls feel sluggish, making altitude and heading difficult to maintain. For this reason, most airplanes that fly at above 25,000 ft MSL are equipped with an autopilot.
b. Horsepower. The engine uses a determined weight of air to produce an identified amount of horsepower through internal combustion. For a given decrease of air density, horsepower decreases at a higher rate, which is approximately 1.3 times that of the corresponding decrease in air density.
c. Speed and Velocity. For an airplane to maintain unaccelerated level flight, drag and thrust must be equal. Because density is always greater at sea level, the velocity at altitude given the same AOA will be greater than at sea level, although the IAS will not change. Therefore, an airplane’s TAS increases with altitude while its IAS remains constant. In addition, an airplane’s rate of climb will decrease with altitude.
2-11. EMERGENCIES AND IRREGULARITIES AT HIGH ALTITUDES. All emergency procedures in the AFM should be reviewed before flying any airplane, and be readily accessible during every flight. A description follows of some of the most significant high-altitude emergencies and remedial action for each.
a. Decompression.
(1) Causes and Results. Decompression is the inability of the aircraft’s pressurization system to maintain its designed pressure schedule. Decompression can be caused by a malfunction of the system itself or structural damage to the aircraft. A rapid decompression will often result in cabin fog because of the rapid drop in temperature and the change in relative
Page 36 Par 2-11 humidity. A decompression will also affect the human body. Air will escape from the lungs through the nose and mouth because of a sudden lower pressure outside of the lungs. Differential air pressure on either side of the eardrum should clear automatically. Exposure to wind blast and extremely cold temperatures are other hazards the human body may face with decompression.
(2) Cabin Volume and Decompression Rates. Decompression of a small cabin volume pressurized aircraft is more critical than a large one, given the same size hole or conditions, primarily because of the difference in cabin volumes. Table 2-8, Aircraft Cabin Volume Ratios, is a comparison of cabin volume ratios between several large transport airplanes and some of the more popular GA turbojet airplanes in current use. Table 2-8 also shows that, under the same conditions, a typical small, pressurized aircraft can decompress on the order of 10 to 200 times faster than large aircraft. The B-747/Learjet comparison is an extreme example in that the human response, TUC, and the protective equipment necessary are the same.
Actual decompression times are difficult to calculate due to many variables involved (e.g., the type of failure, differential pressure, cabin volume, etc.). However, it is more probable that the crew of the small aircraft will have less time in which to take lifesaving actions.
TABLE 2-8. AIRCRAFT CABIN VOLUME RATIOS Aircraft Type Cabin Volumes in Cubic Ft Ratio DC-9 vs CE-650 5,840 vs 576 10:1 B-737 vs LR-55 8,010 vs 502 16:1 B-727 vs NA-265 9,045 vs 430 21:1 L-1011 vs G-1159 35,000 vs 1,850 19:1 B-747 vs Learjet 59,000 vs 265 223:1 Data Source: Physiological Considerations and Limitations in the High-altitude Operation of Small Volume Pressurized Aircraft. E. B.
McFadden and D. de Steigner, Federal Aviation Administration (FAA) Civil Aeromedical Institute (CAMI).
(3) Types of Decompression.
(a) Explosive Decompression. A change in cabin pressure faster than the lungs can decompress. Most authorities consider any decompression that occurs in less than 0.5 seconds as explosive and potentially dangerous. This type of decompression is more likely to occur in small volume pressurized aircraft than in large pressurized aircraft and often results in lung damage.
To avoid potentially dangerous flying debris in the event of an explosive decompression, properly secure all loose items such as baggage and oxygen cylinders.
(b) Rapid Decompression. A change in cabin pressure where the lungs can decompress faster than the cabin. The risk of lung damage is significantly lower in this decompression compared to an explosive decompression.
(c) Gradual or Slow Decompression. A gradual or slow decompression is dangerous because it may not be detected. Automatic visual and aural warning systems generally provide an indication of a slow decompression.
Par 2-11 Page 37
(4) Recovery. Recovery from all types of decompression is similar. Regardless of the type of decompression, recognition of the decompression, awareness of cabin altitude/cabin pressurization warning systems, or recognition of hypoxia symptoms are essential for a safe recovery.
WARNING:
If hypoxia is suspected, immediately don oxygen mask and breathe 100 percent oxygen slowly. Descend to a safe altitude. If supplemental oxygen is not available, initiate an emergency descent to an altitude below 10,000 ft MSL. If symptoms persist, land as soon as possible.
(a) Oxygen. Because hypoxia can drive an increase in respiration as a reaction to make up for a lack of oxygen, you should carefully control your breathing rate and depth. The excessive rate and depth of respiration (hyperventilation) can cause symptoms similar to hypoxia. To recover from hypoxia, breathe 100 percent oxygen; it will not worsen hyperventilation. Thus, for either hypoxia or hyperventilation, the recovery procedures are the same—breathe 100 percent oxygen and slow the breathing rate. In some cases, particularly recovery from an extreme hypoxia exposure, the administration of 100 percent oxygen can cause an apparent increase in severity of symptoms lasting for 15–60 seconds. Even if this reaction occurs, the recovery procedures remain as described above. Breathe 100 percent oxygen and breathe slowly.
(b) Descent. Although top priority in such a situation is reaching a safe altitude, pilots should be aware that cold-shock in piston engines can result from a high-altitude rapid descent, causing cracked cylinders or other engine damage. The time allowed to make a recovery to a safe altitude before loss of useful consciousness is, of course, much less with an explosive decompression than with a gradual decompression.
b. Turbocharger Failure or Malfunction. Increased oil temperature, decreased oil pressure, and a drop in manifold pressure could indicate a turbocharger malfunction or a partial or complete turbocharger failure. The consequences of such a malfunction or failure are twofold.
The airplane may not be capable of sustaining altitude without the additional power supplied by the turbocharged system. The loss in altitude in itself would not create a significant problem, weather and terrain permitting, but you must notify ATC of the descent.
CAUTION:
Loss of cabin pressurization can occur if the pressurization system is dependent on the turbocharger compressor. Careful monitoring of pressurization levels is essential during the descent to avoid the onset of hypoxia from a slow decompression.
c. Vapor Lock. Another potential problem associated with turbochargers is fuel vaporization. Engine-driven pumps that pull fuel into the intake manifold are susceptible to vapor lock at high altitudes. Most high-altitude aircraft are equipped with tank-mounted boost
Page 38 Par 2-11 pumps to feed fuel to the engine-driven pump under positive pressure. These pumps should be turned on if fuel starvation occurs as a result of vapor lock.
d. In-Flight Fire. Because of the highly combustible composition of oxygen, if a fire breaks out during a flight at high altitude, pilots should initiate an immediate descent to an altitude that does not require oxygen. Follow the procedures in the AFM.
e. Flight Through Thunderstorm Activity or Known Severe Turbulence. When pilots anticipate flight through severe turbulence and/or it is unavoidable, we recommend the following procedure:
CAUTION:
Flight through thunderstorm activity or known severe turbulence should be avoided, if possible.
(1) Airspeed. Airspeed is critical for any type of turbulent air penetration. Use the AFM-recommended turbulence penetration target speed or, if unknown, fly an airspeed below maneuvering speed. Use of high airspeeds can result in structural damage and injury to passengers and crewmembers. Severe gusts may cause large and rapid variations in IAS. Do not chase airspeed.
(2) Altitude. Penetration should be at an altitude that provides adequate maneuvering margins in case severe turbulence is encountered to avoid the potential for catastrophic upset.
(3) Autopilot. If severe turbulence is penetrated with the autopilot on, the altitude hold mode should be off. If the autopilot has a pitch hold mode, it should be engaged. The autopilot pitch hold mode can usually maintain pitch more successfully than a pilot under stress. With the autopilot off, the yaw damper should be engaged. Controllability of the aircraft in turbulence becomes more difficult with the yaw damper off. Rudder controls should be centered before engaging the yaw damper.
(4) Lightning. When flight through a thunderstorm cannot be avoided, turn up the intensity of panel and cabin lights so lightning does not cause temporary blindness. White lighting in the cockpit is better than red lighting during thunderstorms.
(5) Attitude and Heading. Keep wings level and maintain the desired pitch attitude and approximate heading. Do not attempt to turn around and fly out of the storm because the speed associated with thunderstorms usually makes such attempts unsuccessful. Use smooth, moderate control movements to resist changes in attitude. If large attitude changes occur, avoid abrupt or large control inputs. Avoid, as much as possible, use of the stabilizer trim in controlling pitch attitudes. Do not chase altitude.
2-12. FLIGHT TRAINING. Flight training required to comply with § 61.31(g) may be conducted in a simulator that meets the requirements of part 121, § 121.407 or a high-altitude airplane. The simulator should be representative of an airplane that has a service ceiling or maximum operating altitude, whichever is lower, above 25,000 ft MSL. The training should
Par 2-12 Page 39 consist of as many flights as necessary to cover the following procedures and maneuvers. If an airplane is being used, each flight should consist of a preflight briefing, flight planning, a preflight inspection, demonstrations by the instructor of certain maneuvers or procedures when necessary, and a postflight briefing and discussion.
a. Preflight Briefing. The instructor should verbally cover the material that will be introduced during the flight. If more than one flight is required, previous flights should be reviewed at this time. The preflight briefing is a good time to go over any questions the trainee may have regarding operations at high altitudes or about the aircraft. The instructor should encourage questions by the trainee during all portions of the flight training.
b. Preflight Planning. Complete a thorough flight plan for a predetermined route. The flight plan should include a complete weather briefing. Contact a Flight Service Station (FSS) (1-800-WX-BRIEF) or use one of the various Internet-based services such as Direct User Access Terminal System (DUATS) to obtain a weather briefing. Determine the altitude for the flight using winds, pilot reports, the freezing level, and other meteorological information obtained from the briefing to determine the best altitude for the flight. Retain the information to aid in subsequent calculations made during flight.
(1) Course Plotting. Plot the course on a high-altitude navigation chart, noting the appropriate jet routes and required reporting points on a navigation log. Low-altitude charts should be available for planning departures and arrivals to comply with airspace and airspeed requirements. Identify and note alternate airports.
(2) AFM. Review the AFM with particular attention to Weight and Balance (W&B), performance charts, and emergency procedures. Calculate oxygen requirements, airspeeds, groundspeeds, time en route, and fuel burn using the AFM and weather data, when applicable.
Plan fuel management and descents at this time. The AFM should be readily accessible in the cabin in the event of an emergency.
(3) Flight Planning. Complete a flight plan using appropriate jet routes from the en route high-altitude chart. File the flight plan with the nearest FSS, ATC facility, or one of the online services, such as DUATS.
c. Preflight Inspection. The aircraft checklist should be followed carefully. Particular attention should be given to the aircraft’s fuselage, windshields, window panels, and canopies to identify any cracks or damage that could rupture under the stress of cabin pressurization. The inspection should also include a thorough examination of the aircraft oxygen equipment, including available supply, an operational check of the system, and assurance that supplemental oxygen is in a readily accessible location.
• Preflight the oxygen equipment so that the system is ready for use upon donning the mask.
• Demonstrate crew communications using the oxygen equipment, both between crewmembers (if more than one required pilot) and with ATC.
d. Run-Up, Takeoff, and Initial Climb. Follow the procedures in the AFM, particularly the manufacturer’s recommended power settings and airspeeds, to avoid overboosting the
Page 40 Par 2-12 engine. Standard callout procedures are highly recommended and should be used for each phase of flight where the airplane crew consists of more than one crewmember.
e. Climb to High Altitude and Normal Cruise Operations While Operating Above 25,000 Feet MSL. Perform the transition from low to high altitude repeatedly to assure familiarity with appropriate procedures. Pay attention to energy state awareness and automation management during the climb. Specific oxygen requirements should be met when climbing above 12,500 ft MSL and pressurization should be adjusted with altitude. When passing through FL 180, the altimeter should be set to 29.92 inHg and left untouched until descending below that altitude. Comply with reporting points, and also with appropriate altitude selection for direction of flight. Throughout the entire climb and cruise above 25,000 ft MSL, emphasis should be given to monitoring cabin pressurization.
(1) Vertical Speed Mode (VS) at High Altitude. Use of VS mode has considerable risk during high-altitude climb. When an aircraft is in VS mode, airplane speed is controlled by thrust. VS mode prioritizes the command VS rate; thus speed can decay when thrust available is less than thrust required. Improper use of VS can result in speed loss with a potential for stall conditions.
(2) Max Continuous Thrust (MCT) at Cruise Altitude. Thrust will increase to the selected cruise limit. Select MCT to increase available thrust and stop airspeed decay. If the airspeed deteriorates, the only option is to descend.
f. Simulated Emergencies. Training should include at least one simulated rapid decompression and emergency descent. Do not actually depressurize the airplane for this or any other training. Actual decompression of an airplane can be extremely dangerous and should never be done intentionally for training purposes. Simulate the decompression by donning the oxygen masks, turning on the oxygen controls, configuring the airplane for an emergency descent, and performing the emergency descent as soon as possible. Coordinate with ATC in advance of any practice emergency descent. Do not vacate any assigned altitude without clearance.
g. Descents. Gradual descents from altitude should be practiced to provide passenger comfort and compliance with procedures for transitioning out of the high-altitude realm of flight.
Follow the airplane manufacturer’s recommendations with regard to descent power settings to avoid stress on the engine and excessive cooling. VS mode may be used for descent; however, selecting excessive vertical speeds can result in airspeed increases into an overspeed condition.
Particular emphasis should be given to cabin pressurization and procedures for equalizing cabin and ambient pressures before landing. Emphasis should also be given to changing to low-altitude charts when transitioning through FL 180, obtaining altimeter settings below FL 180, and complying with airspace and airspeed restrictions at appropriate altitudes.
h. Engine Shutdown. Allow the turbocharged engine to cool for at least 1 minute and assure that all shutdown procedures in the AFM are followed. Before exiting the airplane, always check that all oxygen equipment and oxygen valves have been turned off or placed in the position recommended by the manufacturer.
i. Postflight Discussion. The instructor should review the flight and answer any questions the trainee may have. If additional flights are necessary to ensure thorough understanding of high-altitude operations, preview the material for the next flight during the postflight discussion.