Appendix B B-5 B.7.2.6 Pilot Training. Submit applicable portions of proposed CAVS-specific pilot training material and include a description of the methods used to conduct, evaluate, and manage the training. The CAVS pilot training should include:
1. ADS-B Out/In system overview (if not previously addressed with another ADS-B application).
2. ADS-B CAVS system operations.
3. CAVS normal procedures:
• Visual separation procedures.
• Speed management.
• Assessing closure rates.
• Wake turbulence avoidance.
• Weather minimums.
• Use of and response to the selectable CAVS range alert.
• Crew coordination during CAVS.
4. CAVS MEL procedures (as applicable).
5. CAVS equipment limitations.
6. CDTI interface.
7. Contingency procedures.
Appendix C C-1 APPENDIX C. ADS-B IN OPERATIONS—AIRCRAFT QUALIFICATION AND
MAINTENANCE C.1 Purpose. This appendix provides guidance on aircraft qualification, maintenance, and maintenance personnel training associated with authorization of ADS-B In operations.
C.2 Applicability. The ADS-B In aircraft qualification and maintenance guidance contained herein applies to operations conducted under 14 CFR parts 91, 91 subpart K (14 CFR part 91K), 121, 125 (including 14 CFR part 125 Letter of Deviation Authority (LODA)), 129, and 135. Title 14 CFR part 91 operators (excluding 14 CFR part 91K operators) should comply with the guidance contained in this appendix. Operators conducting operations under 14 CFR parts 91K, 121, 125 (including 14 CFR part 125 LODA), 129, and 135 should address all aspects of the guidance contained in this appendix when submitting requests for authorization of ADS-B In operations.
C.3 Aircraft Qualification.
C.3.1 ADS-B In systems must meet the standards of the appropriate Technical Standard Order (TSO)-C195b, Avionics Supporting Automatic Dependent Surveillance – Broadcast (ADS-B) Aircraft Surveillance Applications (ASA), or later revision, for authorization.
Guidance on the installation of ADS-B Out equipment can be found in AC 20-165, Airworthiness Approval of Automatic Dependent Surveillance - Broadcast OUT Systems. Guidance on the installation of ADS-B In systems can be found in AC 20-172, Airworthiness Approval for ADS-B In Systems and Applications.
C.3.2 Applications submitted to the FAA for authorization to conduct ADS-B In operations should contain the following documentation to demonstrate aircraft qualification:
1. Applicable ADS-B In airworthiness documentation in the form of an aircraft type certificate (TC), amended TC, or Supplemental Type Certificate (STC).
2. ADS-B In avionics manufacturer’s instructions for continued airworthiness (ICA), as accepted by the FAA.
3. Proposed minimum equipment list (MEL) revisions, if applicable, listing all limitations and procedures associated with the dispatch of aircraft with the ADS-B In system inoperative.
C.4 Maintenance.
C.4.1 Maintenance of ADS-B In systems should comply with the guidance contained in this paragraph and must comply with applicable airworthiness regulations. Maintenance personnel should be familiar with the operator’s ADS-B In system maintenance procedures, their individual responsibilities with respect to those procedures, and the availability of any resources within or outside of the maintenance organization necessary to ensure the continued airworthiness of the ADS-B In system.
Appendix C C-2 C.4.2 Applications submitted for authorization to conduct ADS-B In operations under 14 CFR parts 91, 91K, 121, 125 (including 14 CFR part 125 LODA), 129, and 135 should include documentation that includes the following, as applicable:
1. The General Maintenance Manual (GMM) and, for 14 CFR part 125, the Policy and Procedures Manual (PPM) should incorporate the ADS-B In manufacturer’s ICA, as accepted by the FAA, and identify any special techniques, maintenance/inspection frequencies, and test equipment used to support the continued airworthiness of the system.
2. Indicate whether ADS-B In system maintenance is integrated into an existing approved maintenance program or is a separate program.
3. Identify the GMM or PPM revision and update procedures, if not previously approved.
4. Identify how maintenance personnel will be trained on the ADS-B In system and the method to record and maintain any associated qualifications.
5. Procedures for ADS-B In software installation, updates, evaluations, tests, and configuration control.
6. Procedures used to make modifications, additions, and changes to the ADS-B In system.
7. Procedures for ADS-B In discrepancy reporting and recording.
8. MEL and logbook procedures for deferral of the ADS-B In system or components of the system.
9. Notification procedures between maintenance control, engineering, flight operations, and dispatch (or equivalent) when the ADS-B In system is deferred.
10. Procedures to monitor and identify ADS-B In-equipped aircraft with chronic discrepancies and restrict the aircraft from ADS-B In operations until appropriate corrective action and verification tests have been performed.
11. Procedures for return to service of the ADS-B In system following routine/nonroutine maintenance or completion of corrective action on an aircraft flagged for chronic discrepancies.
12. Integration of ADS-B In maintenance into existing quality control (QC) and quality assurance (QA) programs, as applicable.
C.5 Maintenance Personnel Training.
C.5.1 General. This paragraph contains guidance on maintenance personnel training associated with ADS-B In operations. Operators should address this guidance, as applicable, in proposals submitted to the FAA for authorization to conduct ADS-B In operations.
C.5.2 Maintenance Training. Maintenance personnel should be knowledgeable of the guidance contained in this AC and applicable regulations. Operator and contract maintenance personnel, including mechanics, maintenance controllers, avionics technicians, and
Appendix C C-3 inspection/QA personnel, should receive initial and recurrent training (as necessary) to establish and maintain an effective ADS-B In maintenance program.
C.5.3 Application Submissions. Applications submitted for authorization to conduct ADS-B In operations should address the following:
1. Identify the person(s) responsible for ensuring ADS-B In maintenance and inspection personnel are properly trained, knowledgeable, and current in accordance with the GMM or PPM, as appropriate.
2. Identify how the ADS-B In training will be conducted (i.e., in-house or outside training provider).
3. Include policy and procedures that address any qualifications for ADS-B In maintenance and inspection personnel.
4. Identify the methods and techniques used to conduct initial and recurrent training
(e.g., Instructor-Led Training (ILT), computer-based training (CBT), and on-the-job training (OJT)).
5. Identify the procedures used to record and maintain initial and recurrent ADS-B In training and qualifications.
6. Include maintenance and inspection training curriculum that addresses the following ADS-B In topics:
• Operational overview;
• Aircraft system overview;
• Maintenance and inspection procedures;
• Personnel training qualifications (as applicable);
• MEL procedures;
• Test equipment and use (as applicable); and
• Return to service test procedures.
Appendix D D-1 APPENDIX D. DEFINITIONS The terms have the following meaning when used in this AC:
D.1 Automatic Dependent Surveillance-Broadcast (ADS-B) Airspace. The airspace specified in 14 CFR § 91.225.
D.2 Automatic Dependent Surveillance-Broadcast (ADS-B) Guidance Display (AGD).
The AGD provides digital readouts and alerts of time-sensitive information located on the Cockpit Display of Traffic Information (CDTI). This is used primarily for installations where the CDTI is not installed in the forward field of view (FOV).
D.3 Automatic Dependent Surveillance-Broadcast (ADS-B) In. ADS-B In is the receipt, processing, and display of ADS-B transmissions. ADS-B In is necessary to utilize ADS-B traffic and broadcast services (e.g., Flight Information Service-Broadcast (FIS-B) and Traffic Information Service-Broadcast (TIS-B)).
D.4 Automatic Dependent Surveillance-Broadcast (ADS-B) Out. Transmission of an aircraft’s position, altitude, velocity, and other information to other aircraft and air traffic control (ATC) surveillance systems.
D.5 Automatic Dependent Surveillance-Rebroadcast (ADS-R). ADS-R is a link-translation and rebroadcast function of the ADS-B ground system that allows both ADS-B frequencies (1090 megahertz (MHz) and 978 MHz) to share information.
D.6 Cockpit Display of Traffic Information (CDTI). This is a generic display that provides the flightcrew with surveillance information about other aircraft, including position.
Traffic information may be obtained from one or multiple sources, including ADS-B, Airborne Collision Avoidance System (ACAS), and TIS-B. The display of information may be hosted on an Electronic Flight Bag (EFB) or the aircraft’s integrated avionics suite.
D.7 Cockpit Display of Traffic Information (CDTI) Assisted Separation on Approach (CAS-A). CAS-A is an operation that builds on the existing CDTI Assisted Visual Separation (CAVS) operation, as described in Appendix B, CAVS Using ADS-B In, and uses the same flight deck avionics as required for CAVS. CAS-A is initiated by the controller, who provides a CAS-A designation instruction that includes the flight identification (FLT ID) for the traffic-to-follow (TTF). The flightcrew identifies the TTF on the CDTI using the FLT ID provided by the controller (visual acquisition is not required).
D.8 Cockpit Display of Traffic Information (CDTI) Assisted Visual Separation (CAVS).
CAVS is an ADS-B In application that assists the flightcrew in maintaining visual separation from ADS-B Out-equipped aircraft.
D.9 Extended Squitter (ES). ES is how ADS-B messages are transmitted from a Mode Select (Mode S) transponder. ES is a long message (e.g., format DF=17) that
Appendix D D-2 Mode S transponders transmit automatically, without interrogation by radar, to announce the own-ship aircraft’s presence to nearby ADS-B-equipped aircraft and ground stations.
D.10 Flight Information Service-Broadcast (FIS-B). FIS-B is a ground broadcast service provided over the 978 MHz frequency Universal Access Transceiver (UAT) data link.
The FAA FIS-B system provides pilots and flightcrews of properly equipped aircraft (ADS-B In) with a flight deck display of certain aviation weather and aeronautical information for advisory-only use.
D.11 Flightcrew. One or more flight deck crewmembers required for the operation of the aircraft.
D.12 Global Navigation Satellite System (GNSS). The generic term for a satellite navigation system, such as the Global Positioning System (GPS), that provides autonomous worldwide geospatial positioning and may include local or regional augmentations.
D.13 Global Positioning System (GPS). GPS is a U.S. satellite-based radio navigation system that provides a global positioning service. The service provided by GPS for civil use is defined in the GPS Standard Positioning Service (SPS) Performance Standard.
D.14 International Civil Aviation Organization (ICAO). A United Nations (UN) organization that is responsible for developing international standards and for recommending practices and procedures covering a variety of technical fields of aviation.
D.15 International Civil Aviation Organization (ICAO) Aircraft Address (Mode S Code).
Address assigned to each aircraft transponder and ADS-B transmitter during registration or change of registration.
D.16 Interval Management (IM). IM is a set of procedures and capabilities designed to provide precise aircraft-to-aircraft spacing, and is suitable for use en route, on a terminal arrival, and final approach.
D.17 In-Trail Procedure (ITP). An ITP is designed primarily for use in nonradar oceanic airspace to enable appropriately equipped ADS-B In aircraft to perform flight level (FL) changes previously unavailable with procedural separation minima applied.
D.18 Mode A. One of a possible 4,096 identification codes that are transmitted from an aircraft transponder or ADS-B transmitter. The Mode A code is also known as the squawk code for the aircraft. The Mode A code is used in ATC for associating flight plans (FP) with surveillance data.
D.19 Mode C. The encoded barometric altitude from an onboard pressure sensor is contained in the Mode C. This altitude information is transmitted by the aircraft transponder in response to an appropriate interrogation from a secondary radar system. The Mode C is used by ATC to determine the altitude of the reporting aircraft.
D.20 Mode S. A Secondary Surveillance Radar (SSR) system that operates using addressed interrogation on 1030 MHz, and the transponder replies on 1090 MHz. Mode S systems
Appendix D D-3 interrogate for aircraft identity (Mode A code), altitude, and other aircraft-specific information. The aircraft transponder replies with the requested information. Mode S supports an ADS-B service known as 1090ES.
D.21 Non-Performing Equipment (NPE). ADS-B Out-equipped aircraft operating contrary to 14 CFR § 91.225 and/or § 91.227.
D.22 Position Source. The onboard avionics equipment that provides the latitude, longitude, geometric altitude, velocity, position and velocity accuracy metrics, and position integrity metric to the ADS-B transmitter. Additionally, the position source may provide the vertical rate parameters. Currently, only GPS, GPS with Wide Area Augmentation Systems (WAAS), and Aircraft-Based Augmentation System (ABAS) sensors tightly integrated with GPS are approved as position sources.
D.23 Secondary Surveillance Radar (SSR). A radar sensor that listens to replies sent by transponders carried on onboard airborne targets. SSR sensors, in contrast to Primary Surveillance Radar (PSR) sensors, require the aircraft under surveillance to carry a transponder.
D.24 Statement of Compliance (SOC). The SOC is a manufacturer-generated document that states the ADS-B equipment, when installed in accordance with the installation instructions, complies with all requirements of 14 CFR § 91.227, and with the performance requirements of the appropriate Technical Standard Order (TSO).
D.25 Surveillance. Detection, tracking, characterization, and observation of aircraft, other vehicles, weather, and airspace status information and phenomena for the purposes of conducting flight operations in a safe and efficient manner. The primary purposes of traffic surveillance (as distinct from all surveillance functionality) are to control the flow of aircraft, to provide situational awareness for pilots and controllers, and to separate aircraft.
D.26 Traffic Information Service-Broadcast (TIS-B). TIS-B is a ground broadcast service provided from an ADS-B ground system network over the UAT and 1090ES links that provides position, velocity, and other information on traffic that is detected by airport surface detection equipment (ASDE), SSR, or Wide Area Multilateration (WAM), but that is not transmitting an ADS-B position. In the United States, TIS-B service will always be deployed with the ADS-R service so that a complete traffic picture is provided for both nonequipped and alternate-link-equipped aircraft.
D.27 Transponder. The airborne radar beacon receiver/transmitter portion of the ATC radar beacon system (ATCRBS) or Mode S system that automatically receives radio signals from interrogators and replies with specific reply information as requested.
D.28 Universal Access Transceiver (UAT). UAT is a wideband multipurpose data link intended to operate globally on a single channel with a channel signaling rate of just over 1 megabit per second (Mbps). By design, UAT supports multiple broadcast services, including FIS-B and TIS-B, in addition to ADS-B.
Appendix D D-4 D.29 Visual Meteorological Conditions (VMC). Weather conditions in which pilots have sufficient visibility to fly the aircraft while maintaining visual separation from terrain and other aircraft. The exact requirements vary by class of airspace (e.g., Class B airspace:
3 statute miles (sm) visibility, clear of clouds).
Appendix E E-1 APPENDIX E. RELATED REGULATIONS AND READING MATERIAL E.1 Related 14 CFR Parts. You can find the Code of Federal Regulations (CFR) online at https://www.ecfr.gov.
1. Section 1.1, General Definitions.
2. Section 21.50, Instructions for Continued Airworthiness and Manufacturer’s Maintenance Manuals Having Airworthiness Limitations Sections.
3. Part 61, Certification: Pilots, Flight Instructors, and Ground Instructors.
4. Section 91.1, Applicability.
5. Section 91.103, Preflight Action.
6. Section 91.130, Operations in Class C Airspace.
7. Section 91.131, Operations in Class B Airspace.
8. Section 91.135, Operations in Class A Airspace.
9. Section 91.217, Data Correspondence Between Automatically Reported Pressure Altitude Data and the Pilot’s Altitude Reference.
10. Section 91.225, Automatic Dependent Surveillance-Broadcast (ADS-B) Out Equipment and Use.
11. Section 91.227, Automatic Dependent Surveillance-Broadcast (ADS-B) Out Equipment Performance Requirements.
12. Part 91 Subpart K (Part 91K), Fractional Ownership Operations.
13. Part 121, Operating Requirements: Domestic, Flag, and Supplemental Operations.
14. Part 125, Certification and Operations: Aircraft Having a Seating Capacity of 20 or More Passengers or a Maximum Payload Capacity of 6,000 Pounds or More; and Rules Governing Persons On Board Such Aircraft.
15. Part 133, Rotorcraft External-Load Operations.
16. Part 135, Operating Requirements: Commuter and On Demand Operations and Rules Governing Persons On Board Such Aircraft.
17. Part 137, Agricultural Aircraft Operations.
E.2 Related Reading Materials (current editions).
• You can find this and other ACs on the FAA’s website at https://www.faa.gov/regulat ions_policies/advisory_circulars or on the Dynamic Regulatory System (DRS) at https://drs.faa.gov.
Appendix E E-2
• Inspectors and air carriers can access FAA Order 8900.1, Flight Standards Information Management System, on DRS. Operators and the public can find this order on the FAA’s website at https://www.faa.gov/regulations_policies/orders_notic es and DRS.
• You can find a current list of Technical Standard Orders (TSO) on DRS.
E.2.1 FAA Guidance Material.
1. AC 20-165, Airworthiness Approval of Automatic Dependent Surveillance - Broadcast OUT Systems.
2. AC 20-172, Airworthiness Approval for ADS-B In Systems and Applications.
3. FAA Order 8900.1, Volume 3, Chapter 18, Section 3, Operations Specification (OpSpec)/Management Specification (MSpec)/Letter of Authorization (LOA) A354, Automatic Dependent Surveillance-Broadcast (ADS-B) In-Trail Procedure (ITP).
4. Aeronautical Information Manual (AIM), Paragraph 4-5-7, Automatic Dependent Surveillance-Broadcast (ADS-B) Services, through Paragraph 4-5-10, Automatic Dependent Surveillance-Rebroadcast (ADS-R).
5. Surveillance and Broadcast Services Description Document (SRT-047).
E.2.2 FAA TSOs (edition listed below or later revision).
1. TSO-C129a, Airborne Supplemental Navigation Equipment Using the Global Positioning System (GPS).
2. TSO-C145c, Airborne Navigation Sensors Using the Global Positioning System Augmented by the Satellite Based Augmentation System (SBAS).
3. TSO-C146c, Stand-Alone Airborne Navigation Equipment Using the Global Positioning System Augmented by the Satellite Based Augmentation System (SBAS).
4. TSO-C154c, Universal Access Transceiver (UAT) Automatic Dependent Surveillance-Broadcast (ADS-B) Equipment Operating on Frequency of 978 MHz.
5. TSO-C157a, Aircraft Flight Information Services-Broadcast (FIS-B) Data Link Systems and Equipment.
6. TSO-C166b, Extended Squitter Automatic Dependent Surveillance - Broadcast (ADS-B) and Traffic Information Service - Broadcast (TIS-B) Equipment Operating on the Radio Frequency of 1090 Megahertz (MHz).
7. TSO-C195b, Avionics Supporting Automatic Dependent Surveillance – Broadcast (ADS-B) Aircraft Surveillance Applications (ASA).
8. TSO-C196a, Airborne Supplemental Navigation Sensors for Global Positioning System Equipment Using Aircraft-Based Augmentation.
E.2.3 RTCA, Inc. Documents. You can find the most recent editions of RTCA documents available for purchase at https://my.rtca.org/nc__store.
Appendix E E-3
1. RTCA DO-260B, Minimum Operational Performance Standards for 1090 MHz Extended Squitter Automatic Dependent Surveillance - Broadcast (ADS-B) and Traffic Information Services - Broadcast (TIS-B).
2. RTCA DO-282, Minimum Operational Performance Standards for Universal Access Transceiver (UAT) Automatic Dependent Surveillance - Broadcast (ADS-B).
3. RTCA DO-312 Supplement, Safety, Performance and Interoperability Requirements Document for the In Trail Procedure in Oceanic Airspace (ATSA-ITP) Application.
4. RTCA DO-317B, Minimum Operational Performance Standards (MOPS) for Aircraft Surveillance Applications (ASA) System.
5. RTCA DO-328B, Safety, Performance and Interoperability Requirements Documents for Airborne Space – Flight Deck Interval Management (ASPA-FIM).
6. RTCA DO-354, Safety and Performance Requirements Document for CDTI Assisted Visual Separation (CAVS).
7. RTCA DO-361A, Minimum Operational Performance Standards (MOPS) for Flight-Deck Interval Management (FIM).
E.3 European Union Aviation Safety Agency (EASA) Publications (current editions).
1. EASA Acceptable Means of Compliance (AMC) 20-24, Certification Considerations for the Enhanced ATS in Non-Radar Areas Using ADS-B Surveillance (ADS-B-NRA) Application via 1090 MHz Extended Squitter.
2. EASA Certification Specifications and Acceptable Means of Compliance for Airborne Communications, Navigation and Surveillance (CS-ACNS).
Appendix F F-1 APPENDIX F. INTERVAL MANAGEMENT
CONTENTS Paragraph Page
F.1 PurposeF-3
F.2 BackgroundF-3
F.3 IM DescriptionF-3
F.3.1 IM Description—Ground ComponentF-3
F.3.2 IM Description—Airborne ComponentF-3
F.3.3 Notional PhraseologyF-4
F.3.4 Early FIM AvionicsF-4
F.4 IM TerminologyF-4
F.4.1 Assigned Spacing Goal (ASG)F-4
F.4.2 Cross Point (CP)F-4
F.4.3 Designated TrafficF-4
F.4.4 Flight-Deck Interval Management (FIM) AvionicsF-4
F.4.5 Flight Identification (FLT ID)F-5
F.4.6 Interval Management (IM) AircraftF-5
F.4.7 Interval Management (IM) Clearance TypeF-5
F.4.8 Interval Management (IM) Path MonitoringF-5
F.4.9 Interval Management (IM) SpeedF-5
F.4.10 Interval Management (IM) Speed Compliance MonitoringF-5
F.4.11 Planned Cancellation Point (PCP)F-5
F.4.12 Selected TrafficF-5
F.5 IM Clearance Types DescribedF-5
F.5.1 Clearance Type FormatF-6
F.5.2 Maintain Current SpacingF-6
F.5.3 Capture Then MaintainF-7
F.5.4 Achieve-by Then Maintain (“Cross”)F-7
F.5.5 Final Approach SpacingF-8
F.5.6 IM SuspendF-8
F.5.7 SafeRoute+ DifferencesF-8
F.5.7.1 Maintain Current Spacing and Capture Then MaintainF-8