e. Air Temperature and Pressure. Icing tends to be found in low-pressure areas and at temperatures at or around freezing. For areas of low pressure, pilots can scan the surface analysis charts, and for freezing levels, the winds aloft chart can be used because the wind direction and speed grouping also provide air temperature at that altitude.
f. Alternatives. When contemplating flight into possible icing conditions in an aircraft approved for flight in icing conditions, a major consideration of preflight planning is to have alternative courses of action if conditions are worse than expected. These alternatives could be a change in altitude, heading, airspeed, or an alternate airport with adequate runway length.
g. It is important to note that aircraft that are approved for instrument flight rules (IFR) operations but not certified for known icing conditions are not testing during the certification process for inadvertent icing encounters. Therefore, pilots in such aircraft should emphasize ice avoidance during preflight planning and pay special attention to planning an alternate course of action in case actual icing is encountered.
Page 40 Par 5-9
CHAPTER 6. IN-FLIGHT OPERATIONS
6-1. AVAILABLE IN-FLIGHT INFORMATION.
a. Flight Watch. There are numerous sources of meteorological information available to pilots while in flight. A principal source of this information is Flight Watch. Flight Watch is an FSS-provided en route flight advisory service designed to provide, upon request, timely weather information pertinent to the type, route, and altitude of flight. Flight Watch is available from 6 AM to 10 PM local time at altitudes generally above 5,000 feet above ground level (AGL). For weather information at other times or at lower altitudes, contact an AFSS via radio on a nearby frequency outlet as depicted on aeronautical charts. The FSSs providing this service are listed in the Airport/Facility Directory and can be contacted on radio frequency 122.0 MHz.
b. Hazardous In-flight Weather Advisory Service. The Hazardous In-flight Weather Advisory Service (HIWAS) provides continuous, recorded hazardous in-flight weather forecasts over selected VHF omnidirectional radio (VOR) outlets within the HIWAS broadcast area. This broadcast area is a geographical zone of responsibility, including one or more HIWAS outlet areas (defined as the area within a 150-nautical mile radius of the HIWAS outlet) assigned to an FSS for hazardous weather advisory broadcasting.
c. Transcribed Weather Broadcast. The Transcribed Weather Broadcast (TWEB) is a continuous recording of meteorological and aeronautical information broadcast on low/medium frequencies and VOR facilities for pilots. The TWEB is based on a route-of-flight concept that, among other information, includes adverse conditions, route forecasts, outlooks, and PIREPs that may contain useful icing-related information.
d. Air Carrier Dispatch. Air carrier flightcrews normally can contact their dispatch facilities on specified company frequencies or through their airplane’s onboard Aircraft Communications Addressing and Reporting System (ACARS). Dispatch can then relay icing information, changes in front movement or speed, or recent icing PIREPs.
e. Weather Radar. Since airborne weather radar detects raindrops, cells painted on radar should be avoided when the temperatures are at or near freezing. Airborne weather radar cannot, however, detect drizzle-size drops or cloud-size drops, and therefore should not be relied upon to detect icing in clouds or freezing drizzle. It also lacks the ability to detect small dry ice crystals that can be in heavy concentrations near convective weather systems.
f. Datalink/Satellite Radio.
(1) Pilots now have the option to subscribe to and receive real-time weather and airspace information via Sirius and XM satellite radio to their panel-mounted or handheld avionics. For a fee, these services provide graphical METARs, TAFs, SIGMETs, and AIRMETs, updated pilot reports, updated winds and temperatures aloft, information on severe thunderstorms, icing levels, and graphical displays of temporary flight restrictions.
(2) Such up-to-date information can assist pilots in avoiding hazardous weather, and identifying potentially hazardous areas of unforecast weather.
Par 6-1 Page 41
6-2. PILOT STRATEGIES. Flight into icing conditions is to be avoided if the aircraft is not certificated for flight into such conditions or otherwise equipped in accordance with § 91.527 (b).
However, even if the aircraft can, by regulation, operate into icing conditions; it should not be regarded by pilots as blanket authority to fly through any weather conducive to aircraft icing.
a. Icing in Stratiform Clouds. Because the icing conditions in stratiform clouds often are confined to a relatively thin layer, either climbing or descending may be effective in exiting the icing conditions within the clouds.
(1) A climb may take the aircraft into a colder section of cloud that consists exclusively of ice particles. These generally constitute little threat of structural icing because it is unlikely that the ice particles will adhere to unheated surfaces.
(2) The climb also may take the aircraft out of the cloud altogether to an altitude where the ice gradually will sublimate or shed from the airframe depending on the conditions. A descent may take the airplane into air with temperatures above freezing, within or below the cloud, where the ice can melt.
b. Icing in Cumuliform Clouds. Hazardous icing conditions can occur in cumulus clouds, which sometimes have very high liquid water content. Therefore, it is not advisable to fly through a series of such clouds or to execute holds within them. However, because these clouds normally do not extend very far horizontally, any icing encountered in such a cloud may be of limited duration; it may be possible to deviate around the cloud.
c. Snow.
(1) Normally snow itself is not a hazard with respect to icing, unless it begins to adhere to aircraft surfaces. If snow does begin to stick, it should then be treated as an icing encounter because ice may begin to form under this accumulation of snow. No aircraft is evaluated in the icing-certification process for this rare situation. If it occurs, the aircraft should exit the conditions as quickly as possible, coordinating with ATC as necessary.
(2) However, as discussed in paragraph 4-17, Visual Cues of SLD Conditions, freezing drizzle can co-exist with snow. If you are flying into or over areas reporting snow, it is important to understand that the presence of snow does not necessarily mean that icing conditions are not present. See following paragraph for further information.
d. Freezing Rain and Drizzle.
(1) Freezing rain forms when rain becomes supercooled by falling through a subfreezing layer of air. Thus, it may be possible, to exit the freezing rain by climbing into the warm layer.
(2) Because freezing drizzle often forms by the collision-coalescence process, the pilot should not assume that a warm layer of air exists above the aircraft. A pilot encountering freezing drizzle should exit the conditions as quickly as possible either vertically or horizontally.
The three possible actions are to ascend to an altitude where the freezing drizzle event is less Page 42 Par 6-2
Par 6-2 Page 43 (and 44) intense, to descend to an area of warmer air, or to make a level turn to emerge from the area of freezing drizzle.
e. Ice Pellets. Ice pellets by themselves are not a hazard to the airframe with respect to icing. However, a ground observation of ice pellets could indicate SLD aloft, so avoid such areas.
f. Ice Crystals. Ice crystals can exist in high concentrations at high altitudes near convective weather systems. Turbine engines can ingest and accrete some ice crystals that can ultimately cause power loss. Therefore, flying through clouds near convective weather should be avoided and engine nacelle anti-ice systems should be activated. Refer to your airplane’s AFM for specific information.
g. Communications with ATC. If an aircraft that is not approved for flight in icing conditions inadvertently encounters ice, controllers will not know if the aircraft is certificated or equipped for icing, the severity of the conditions, or what anti-icing or deicing equipment is installed on the aircraft. Therefore, it is imperative that ATC be thoroughly informed and a change in altitude or heading requested as soon as possible in order to exit the icing conditions.
(1) Communications from the pilot should focus on the icing conditions, whether an alteration of the current course and altitude is required, and, if necessary, an alternate landing site selected. In the congested airspace that exists in some parts of the country, along with the intensity of radio communications in such areas, it is possible that a pilot who encounters icing will not receive a clearance in time to exit the conditions before the safety of the flight is compromised.
(2) In such cases, pilots should declare an emergency to ATC and inform the controller of what actions are being taken by the pilot to cope with the emergency. If an aircraft certificated for flight in icing conditions encounters freezing rain or freezing drizzle, flightcrews should advise ATC and should not attempt sustained flight in these conditions. Final authority and responsibility for the safety of a flight rests with the pilot in command.
(3) Therefore, the pilot should not hesitate to reject a controller’s instructions if, in the judgment of a pilot, those instructions would result in an unsafe condition. To make correct decisions, pilots should have at their disposal as much information as possible, including the capability of the aircraft and its systems, and an awareness of the current and evolving weather situation.
CHAPTER 7. ICING CONSIDERATIONS FOR THE PHASES OF FLIGHT The following is a description of icing considerations as they apply to the phases of flight. This chapter focuses primarily on how to safely fly an aircraft certificated for flight in icing conditions, and when it is advisable to exit those conditions. The following is only a sampling of icing-related items to consider when planning a flight. Pilots should consult the aircraft’s AFM or POH for approved checklists.
7-1. PREFLIGHT. The first step in preparing for any flight is to obtain a thorough weather briefing. This becomes especially crucial when icing conditions are likely. When obtaining a weather briefing, make special note of the following items:
a. Freezing Level. Pilots should locate freezing levels on forecast maps. This will assist in developing a contingency plan in the event icing is encountered.
b. AIRMET and SIGMET. These advisories will alert a pilot to areas of moderate and severe icing. AIRMET “Zulu” is the classification of AIRMET issued for icing. SIGMETs are issued to indicate severe icing not associated with a thunderstorm. Anytime a Convective SIGMET is issued, expect severe icing.
c. PIREPs. PIREPs are an excellent source of information on icing location and type.
d. Precipitation. Knowing the location and type of precipitation forecast will assist in avoiding areas conducive to severe icing.
e. Graphical Data. Supplement your briefing by checking theADDS at:
http://adds.aviationweather.gov. (This site depicts all of the above data in easy to read color graphics, and has the CIP and FIP. The CIP and FIP are updated every hour.)
f. Icing conditions require some additional considerations.
(1) When determining routes of flight, make note of airports along the way and highlight them on the chart for easy identification in case an alternate is needed.
(2) When determining routes, consider the climb performance of the airplane and the route’s minimum altitude, particularly in mountainous terrain. Because the airplane’s climb performance will be degraded in icing conditions, consult the AFM to see if there is degradation data.
(3) Determine icing exit strategies during preflight. Determine if climbing or descending will be viable options.
(4) When choosing alternate airports, remember that if structural icing occurs, higher approach speeds and, consequently, longer runways may become necessary.
(5) Consider carrying a high intensity flashlight for use in locating ice accumulation on the aircraft at night or in low visibility conditions.
Par 7-1 Page 45
Page 46 Par 7-1
(6) Consider using a transceiver as a backup radio in case of a communications loss caused by an antenna icing up and/or breaking off.
(7) If the aircraft is loaded near maximum gross weight, climb performance will be degraded, possibly increasing time spent in icing conditions.
(8) Extra fuel may be necessary because excess drag caused by ice formation may require extra power, increasing fuel consumption.
(9) When performing an aircraft preflight inspection, remove all frost, snow, and ice from the aircraft surfaces because even very small amounts may adversely affect the aerodynamic properties of a wing. Placing an aircraft in a heated hangar is a good method of removing frost, snow, and ice; however, a pilot should ensure the aircraft is dry before removing it from the hangar to prevent the moisture from refreezing on the surface.
g. Frost may appear on an aircraft even if the air temperature is well above freezing.
This can occur if the airplane is flown in temperatures below freezing, causing the fuel to become cold-soaked. In flight or after landing, ice and frost can form on the wing in the same fashion that condensation forms on a cold soft drink can. Certain airplanes may be more vulnerable to ice formation from cold-soaked fuel than others may. An airplane sitting outside on a clear night may cause the airplane’s skin temperature to fall below freezing due to radiation cooling. If there is moisture present, frost can form on the airplane skin.
h. Frost, snow, or ice also can be removed with freezing-point depressant fluids. See AC 120-58, Pilot Guide Large Aircraft Ground Deicing, or AC 135-17, Pilot Guide Small Aircraft Ground Deicing, for discussion of the proper use of the fluids and protection provided under various environmental conditions as summarized in holdover timetables. Anti-icing fluids are designed to be shed by the time the aircraft reaches rotation speed; consequently, they provide no protection once the aircraft is airborne. Even though holdover times for freezing drizzle and light freezing rain exist, aircraft certificated for flight in icing conditions are not evaluated for flight in freezing drizzle or freezing rain.
i. Caution should be exercised when choosing an anti-icing fluid because Type II and IV fluids are not appropriate for use on aircraft with a rotation speed of less than 110 knots due to incomplete flowoff and resulting lift losses and control problems. Check the AFM to see if the use of Type II, III, or IV fluids is approved. In some cases, there may be limitations on takeoff procedure or minimum outside air temperature. If fluids are not mentioned in the AFM, consult with airplane manufacturer.
j. Ensure there is no ice that may interfere with control surface movement, braking, or steering. Check the pitot heat, pitot tube opening, and stall warning system. Check for proper functioning of any anti-icing or deicing systems. For fluid systems, make sure you see fluid along the entire leading panels. It may take several minutes to “prime” the fluid system, particularly if it has not been used in a while. Do not assume that any contamination, even snow, will blow off during takeoff. Wet snow may not blow off, and there may be a layer of ice under the snow.
7-2. TAXI. Always perform a pretakeoff check of the anti-ice/deice systems in accordance with the AFM or POH prior to takeoff.
a. While taxiing in snow or ice, leave extra space around your aircraft and taxi at a slower rate. Be careful when braking to prevent the wheels from skidding.
b. When stopping, begin to brake earlier than normal because the aircraft may require more distance to stop. Leave additional space in front of the aircraft during an engine run-up; the aircraft may begin to slide on ice. Carefully check the braking action of the aircraft to ensure that snow or ice is not building up on any of the components of the brake system.
c. If the aircraft is equipped with wheel fairings, be aware that snow may accumulate in the wheel fairings and freeze during flight. Make sure that all controls have full range of motion, and, if applicable, check that the carburetor heat is working.
d. If the aircraft is not equipped with windshield anti-icing or deicing system, turn the defroster on high and leave it on. This may help to prevent ice from forming on the windshield during flight.
7-3. TAKEOFF AND CLIMBOUT. Depending on the recommendations of the manufacturer, the POH, or the AFM, on small aircraft and on certain light aircraft, it may be advisable during climbout to apply the brakes and cycle the landing gear to break loose any snow, slush, or ice that may have accumulated during taxi and takeoff.
a. Verify that the airspeed indicator is working properly and that the pitot heat is on.
Because of ATC restrictions and other traffic, climbout may not always be expeditious.
b. Airplanes are vulnerable to ice accumulation during the initial climbout in icing conditions because lower speeds often translate into a higher AOA. This exposes the underside of the airplane and its wings to the icing conditions and allows ice to accumulate further aft than it would in cruise flight.
c. Consequently, any ice that forms may be out of the pilot’s view and go undetected.
Extreme vigilance should be exercised while climbing with the autopilot engaged. Climbing in Vertical Speed (VS) mode in icing conditions is highly discouraged.
d. As ice accretes on aircraft without autothrottles, the autopilot will attempt to hold a vertical speed without regard for airspeed, leading to a potential stall situation. It is critical that the pilot monitor airspeed to assure that at least the minimum flight speed for the configuration and environmental conditions is maintained.
7-4. CRUISE. An aircraft that is certificated for flight in icing conditions will be able to cope with most icing encounters provided that its ice protection systems are operating properly and that the exposure is not extended beyond their capabilities. However, if it is possible to exit the icing conditions by a change in altitude or a minor change in flight path, this is certainly advisable. During any icing encounter, the pilot should carefully monitor the behavior of the aircraft.
Par 7-2 Page 47
Page 48 Par 7-4
a. The aircraft will have some unprotected areas that will collect ice. Although ice in such areas should not compromise the safety of flight, it may cause enough increase in drag to require the pilot to apply more power to maintain flight speed.
b. Residual or intercycle ice on deiced areas can have a similar effect. Typically, adding power is the recommended action, since reduction in flight speed is associated with an increase in AOA, which on many aircraft will expose larger unprotected areas on the underside of the aircraft to the collection of ice. If for any reason (ice protection failure, improper use of protection system in extreme icing conditions, etc.) the point is reached where it is no longer possible to maintain airspeed through addition of power, the pilot should exit icing conditions immediately.
c. On an aircraft equipped with in-flight deicing systems, there will at all times be residual or some stage of intercycle ice on the wings.
d. Airspeed in cruise can have a significant effect on the nature of an icing encounter.
An aircraft that cruises at a fast airspeed will increase the rate of ice accumulation. However, if the airspeed is sufficiently fast, surface heating due to compressibility effects may melt some of the ice and prevent accumulation in those areas. Generally, only very high-performance aircraft can attain such speeds. During the flight, periodically verify that all anti-icing and/or deicing systems are working. During the en route portion of the flight, have an exit plan that is regularly reevaluated as necessary.
e. Even if the encounter is short and the icing not heavy, the pilot should exercise particular awareness of the behavior of the airplane. Configuration changes following cruise in icing conditions, such as spoiler/flap deployment, should be made with care. This is because ice on the aircraft that had little effect in cruise may have a much different and potentially more hazardous effect in other configurations. Remember that for normal cruise configurations and speeds, both the wing and tailplane are ordinarily at moderate AOA, making wing or tailplane stall unlikely. After configuration changes and in maneuvering flight, wings or tailplane (especially after flap deployment) may be at more extreme AOA, and even residual or intercycle ice may cause a stall to occur at a less extreme angle than on a clean aircraft.
f. Again, care should be exercised when using an autopilot in icing conditions, while in cruise, just as in other phases of flight. When the autopilot is engaged, it can mask changes in handling characteristics due to aerodynamic effects of icing that would be detected by the pilot if the airplane were being hand flown. In an aircraft that relies on aerodynamic balance for trim, the autopilot may mask control anomalies that would otherwise be detected at an early stage. If the aircraft has non-boosted controls, a situation may develop in which autopilot servo-control power is exceeded. The autopilot disconnects abruptly, and the pilot is suddenly confronted by an unexpected control deflection.
g. Pilots may consider periodically disengaging the autopilot and hand flying the airplane when operating in icing conditions. If this is not desirable because of cockpit workload levels, pilots should monitor the autopilot closely for abnormal trim, trim rate, or airplane attitude. As ice accretes on aircraft without autothrottles, the autopilot will attempt to hold altitude without regard for airspeed, leading to a potential stall situation.
h. It is critical that the pilot monitor airspeed to assure that at least the minimum flight speed for the configuration and environmental conditions is maintained. There have been events in which the airspeed loss from cruise to stall occurred in a matter of minutes.
i. Care should be exercised when operating turbine engine powered aircraft in or around convective weather systems. Ice crystals can be accreting in the engine even though the airframe and ice detectors may not show any indications of an icing environment. This can occur at very low ambient temperatures and high altitudes. Nacelle and engine anti-ice systems should be activated if the presence of ice crystals is suspected.
7-5. DESCENT.
a. Pilots should try to stay on top of a cloud layer as long as possible before descending into the clouds. This may not be possible for an aircraft that uses bleed air for anti-icing systems because an increase in thrust may be required to provide sufficient bleed air. This increased thrust may reduce the descent rate of high-performance aircraft whose high-lift attributes already make descents lengthy without the use of aerodynamic speed brakes or other such devices. The result may be a gradual descent, extending the aircraft’s exposure to icing conditions.
b. If configuration changes are made during this phase of flight, they should be made with care in icing conditions, noting the behavior of the airplane. See the discussion in the preceding chapter.
c. When leveling off, especially with the autopilot engaged, ensure that sufficient power is applied to maintain proper airspeed.
7-6. HOLDING.
a. During holding, an airplane may be more vulnerable to ice accumulation because of the slower speeds and lower altitudes during this phase of flight.
b. Caution concerning the use of the autopilot, as described above, is also applicable to holding during or after flight in icing conditions.
c. If configuration changes (such as deployment of flaps) are made before or during the hold and after or during flight in icing conditions, the pilot should be prepared for any unusual behavior of the airplane during or after the change. If the aircraft reacts adversely to a change of configuration, the pilot should return the aircraft to its original configuration. See the discussion above.
d. Consult the AFM for use of flaps. Many AFMs prohibit use of flaps for extended periods in icing conditions.
Par 7-4 Page 49
Page 50 Par 7-7
7-7. APPROACH AND LANDING.
a. During or after flight in icing conditions, when configuring the airplane for landing, the pilot should be alert for sudden aircraft movements. Often ice is picked up in cruise, when the aircraft’s wing and the tailplane are likely at a moderate AOA, making a relatively ice-tolerant configuration. If effects in cruise are minor, the pilot may feel comfortable that the aircraft can handle the ice it has acquired.
(1) Extension of landing gear may create excessive amounts of drag when coupled with ice. Flaps and slats should be deployed in stages, carefully noting the aircraft’s behavior at each stage.
(2) If anomalies occur, it is best not to increase the amount of flaps or slats and perhaps even to retract them depending on how much the aircraft is deviating from normal performance.
(3) Additionally, before beginning the approach, deicing boots should be cycled because they may increase stall speed and it is preferable not to use these systems while landing.
Once on the runway, pilots should be prepared for possible loss of directional control caused by ice buildup on landing gear.
b. Another concern during approach and landing may be forward visibility. Windshield anti-icing and deicing systems can be overwhelmed by some icing encounters or may malfunction. Pilots have been known to look out side windows or, on small GA aircraft, attempt to remove ice accumulations with some type of tool (e.g., plotter, credit card, etc.)
c. Pilot workload can be heavy during the approach and landing phase. Autopilots help to reduce this load. The advantages of a reduced workload must be balanced against the risks associated with using an autopilot during or after flight in icing conditions. An unexpected autopilot disconnect because of icing is especially hazardous in this phase of flight due to the airplane being flown at a low altitude.
d. Accident statistics reveal that the majority of icing-related accidents occur in the final phases of flight. Contributing factors are configuration changes, low altitude, higher flightcrew workload, and reduced power settings. Loss of control of the airplane is often a factor. The ice contamination may lead to wing stall, ice-contaminated tailplane stall (ICTS), or roll upset.
e. Wing stall and roll upset may occur in all phases of flight. However, available statistics indicate that ICTS rarely occurs until approach and landing. Many AFMs will have a limitation on the maximum flap use approved in icing conditions due to ICTS susceptibility. If your airplane does not have such a limitation, and it was certificated prior to 2000, it may be best to perform a no-flap landing at a higher than normal approach speed if the airplane has accumulated ice on the wings and tailplane. However, because of the higher approach speed, longer runways may be needed for this procedure.
f. During the landing flare, carry higher than normal power if there is ice on the airplane. Many non-fatal icing accidents have been attributed to stall during the flare.
7-8. WING STALL.
a. The wing, when contaminated with ice, will ordinarily stall at a lower AOA, and thus at a higher airspeed. Even small amounts of ice, particularly if rough, may have some effect. An increase in approach speeds may be advisable if any ice remains on the wings. How much of an increase depends on both the aircraft type and the amount of ice. The pilot should consult the AFM or POH.
b. An increased landing speed will mean a longer landing roll; so if possible, the pilot may want to consider a longer runway for increased rollout distances.
c. This discussion of ice-contaminated wing stall is considerably shorter than the discussion of ICTS that follows. This is not because the latter is more frequent. Statistics indicate that incidents or accidents due to ice-contaminated wing stall are the more common result of flight in icing conditions. However, pilots have extensive training in recognizing and coping with wing stalls, but little or no training for tailplane stalls, which are very unusual on most designs when the tailplane is clean. It is also important to recognize that although pilots have extensive training in recognizing and coping with stalls of clean wings, the stall of an ice-contaminated wing will often be markedly different and may call for aggressive pitch down inputs quite unlike those used in the case of a clean wing stall. The stall characteristics of an aircraft with ice-contaminated wings may be markedly degraded, and serious roll control problems are not unusual.
d. As explained in Chapter 4, Icing Effects, Protection, and Detection, the accretion may be uneven between the two wings; therefore, the outer part of a wing, which is ordinarily thinner and thus a better collector of ice, may stall first rather than last. The effectiveness of ailerons may be reduced due to ice formations in front of them on the wing.
7-9. ICE-CONTAMINATED TAILPLANE STALL (ICTS).
a. The basic aerodynamics of ICTS was described briefly in Chapter 4, Icing Effects, Protection, and Detection. ICTS occurs when a tailplane with accumulated ice is placed at a sufficiently negative AOA and stalls.
b. This angle would not be expected to be reached without at least partial deployment of the flaps. There are few, if any, known incidents of ICTS in cruise (when flaps would not ordinarily be deployed). However, when the flaps are deployed, tailplane ice, which previously had little effect other than a minor contribution to drag, now can put the tailplane at or dangerously close to stall.
c. While preparing for the deployment of flaps after or during flight in icing, the pilot should carefully assess the behavior of the aircraft for any buffet or other signs of wing stall. The initial deployment of the flaps should be only partial. Vibration or buffeting that follow deployment is much more likely to be due to incipient tailplane stall than wing stall if there was no vibration buffet before deployment. The reason is that after deploying the flaps, the wing will be at a less positive angle, and so farther from stall, while the tailplane will be at a more negative angle, and so closer to stall. There are a number of specific cues associated with ICTS to which a Par 7-8 Page 51
Page 52 Par 7-9 pilot should be sensitive, particularly during this phase of flight. Most of these cues are less readily detected with the autopilot engaged.
• Elevator control pulsing, oscillations, or vibrations,
• Abnormal nose-down trim change,
• Any other unusual or abnormal pitch anomalies (possibly resulting in pilot-induced oscillations),
• Reduction or loss of elevator effectiveness,
• Sudden change in elevator force (control would move nose down if unrestrained), and
• Sudden uncommanded nose-down pitch.
NOTE: The pilot should observe the following guidelines for action if these cues are encountered:
• Flaps tend to alter the airflow reaching the tailplane and should be retracted immediately to the previous setting, and the appropriate nose-up elevator pressure should be applied.
• Airspeed should be increased appropriately for the reduced flap extension setting.
• Sufficient power should be applied for the airplane’s configuration and conditions. (High engine power settings may adversely affect the response to ICTS conditions at high airspeed in some aircraft designs. Manufacturer’s recommendations in the AFM or POH should be observed regarding power settings.)
• Nose-down pitch changes should be made slowly, even in gusting conditions, if circumstances allow.
• If a pneumatic deicing system is used, the system should be cycled several times to clear the tailplane of ice.
d. Note that some of the measures for recovery from ICTS are the opposite of those for recovery from wing stall. Thus distinguishing between the two is very important. If for any reason there is a large or rough ice accretion on both the wing and tailplane (perhaps because of ice protection system failure), manage approach and landing with great care.
e. Deployment of flaps permits the aircraft to be flown with wings at a less positive attack, decreasing the probability of wing stall. However, the AOA at the tailplane is more negative, putting it closer to stall. Similarly, at any particular flap setting, lower speeds put the aircraft closer to wing stall and higher speeds put it closer to tailplane stall. Thus, there is a restricted operating window with respect to use of the flaps and to airspeed.