TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '775e6996f1f6359c34efbbd3d6024f2b56ff5c721060850a0128bf4f0f9ee2ff' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '775e6996f1f6359c34efbbd3d6024f2b56ff5c721060850a0128bf4f0f9ee2ff' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 13-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
2. TECHNICAL DETAILS
2.1. ACCOMPLISHMENT / INSTRUCTIONS
2.1.1. Removal and Inspection of the HPP driving gear
1. Remove the HPP in accordance with the instructions in Maintenance Manual, Doc. No.
E4.08.04, Section 73-10-03, Paragraph A.
2. Remove the drive gear from the HPP in accordance with the instructions in Maintenance Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph C.
CAUTION: Use only the tool p/n AE300T012-1 provided in the kit of this Service Bulletin to block the gear.
3. To remove the gear from the shaft, use a bearing extractor shown in Section 3.2.
4. Clean the driving gear with non-chlorinated brake cleaner (recommended product Manufacturer: Förch, Product ID.: R510)
5. Visually inspect the driving gear against colour criteria in Table 2 - Driving gear check.
If the acceptable criteria are not met:
• remove the camshafts according to the Maintenance Manual, Doc. No.
E4.08.04, Section 85-30-00 Subparagraph 4A (a) - (h)
• Inspect the cylinder head, camshaft gear, the inlet/outlet camshaft bushing in accordance with the Service Bulletin MSB-E4-035, replace the parts as necessary.
2.1.2. Installation of the new driving gear
2.1.2.1 Driving gear p/n E4A-30-000-201 rev. AB1 or E4A-30-000-601
1. Install the new drive gear in accordance with the instructions in Maintenance Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph D (replace the nut, if required).
Note: Lubricate the gear and the O-ring with engine oil before installing the HPP CAUTION: Use only the tool p/n AE300T012-1 provided in the kit of this Service Bulletin to block the gear.
2. Install the HPP in accordance with the instructions in Maintenance Manual, Doc. No.
E4.08.04, Section 73-10-03, Paragraph B. Refer also to Table 3 for the tightening sequence of the screws.
3. Mark a tool cycle on the Tool Cycle Recording Sheet (included as appendix in this Service Bulletin) and fill the execution report.
Note: One cycle equals the disassembly of the old gear and the installation of the new gear.
CAUTION: When the assembly wrench has reached 100 cycles, discard the tool.
4. Conduct an engine ground run of 15 mins, of which 5 mins are MTOP (maximum take-off power).
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 14-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
5. After the ground run, do the following steps:
o remove the HPP – refer to the Maintenance Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph A o Clean and inspect the HPP driving gear against the criteria in MSB-E4-035, latest revision. If acceptable criteria are not met:
▪ remove the camshafts – refer Maintenance Manual, Doc. No. E4.08.04, Section 85-30-00 Subparagraph 4A (a) - (h) ▪ Inspect the cylinder head, camshaft, camshaft gear, the inlet/outlet camshaft bearings in accordance with the Service Bulletin E4-035, replace the parts as necessary.
6. Install again the HPP in accordance with the instructions of the Maintenance Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph B.
2.1.2.2 Driving gear p/n E4A-30-000-201 Rev. AE.1 or subsequent
1. Install the new drive gear (Refer to Figure 1) in accordance with the instructions in Maintenance Manual, Doc. No. E4.08.04, Section 73-10-03, Paragraph D (replace the nut, if required).
Use a standard open-ended wrench (27 mm) instead of the special tool.
Note: Lubricate the gear and the O-ring with engine oil before installing the HPP
2. Install the HPP in accordance with the instructions in Maintenance Manual, Doc. No.
E4.08.04, Section 73-10-03, Paragraph B. Refer also to Table 3 for the tightening sequence of the screws.
Note: With Rev. AE of the driving gear, the engine ground run should be conducted acc. to the MM (NO 5 min. at MTOP are needed).
Note: With Rev. AE of the driving gear, an inspection after the ground run is not required.
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 15-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at Table 2 - Driving gear check
Fig. 1
Fig. 2
Fig. 3
Fig. 4 Examples of gear in acceptable conditions
Fig. 5
Fig. 6
Fig. 7
Fig. 8 Examples of gear in not acceptable condition
Fig. 9
Fig. 10
Fig. 11
Fig. 12 Examples of gear in not acceptable condition YES NO Consultation with AE required Part acceptable:
Note: • The possible discoloration shown in the non-acceptable gears is due to high friction, which generates heat. When present, the typical discoloration is not homogeneous and presents different shades from black/blue to violet/bronze.
• Check the gear according to the discoloration criteria provided.
• Discoloration is clearly visible on the outer surface of the gear and in the marking zone of the gear.
• Check also for visible discoloration on the face of the teeth.
• Check for excessive wear of the gear.
In case of doubt contact Austro Engine.
X X X X X X X X √ √ √ √
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 16-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
Figure 1 – Driving gear E4A-30-000-201 Rev. AE.1
Table 3 – High Pressure Pump Tightening Sequence
Figure 2 Install the HPP tightening the screws clockwise, according to the figure 1 sequence with 12 Nm.:
- Step 1 – 1 at 50%
- Step 2 – 2 at 50%
- Step 3 – 3 at 50%
- Step 4 - 1 at 100%
- Step 5 - 2 at 100%
- Step 6 - 3 at 100%
1 3 2
Austro Engine GmbH Austro Engine Mandatory Service Bulletin No. MSB-E4-034/3 A-2700 Wiener Neustadt Rudolf-Diesel-Strasse 11 Tel: +43 2622 23000 FAX: +43 2622 23000-2711 Process summarised Check for applicability of the MSB-E4-034 at the latest revision Was the MSB-E4-034 at revision 0 -YES- applied?
NO Remove the HPP Remove the HPP driving gear, and inspect against Is the Gear Go to -NO in acceptable YES conditions?
Install a new gear and the reinstall the HPP is the HPP Gear 'ES p/n E4A-30-000-201 NO rev. AE1 or subsequent installed?
Perform an engine Perform an engine ground run according to ground run (5min.
Maintenance Manual MTOP) Remove of the HPP and inspect the gear Go to Is the Gear in -NO acceptable A conditions?
YES
RELEASE TO Reinstall the HPP
SERVICE First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 17-22 © 2021 by Austro Engine GmbH - AUSTRIA - www.austroengine.at
Austro Engine GmbH JAustro Engine Mandatory Service Bulletin Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt No. MSB-E4-034/3 Tel: +43 2622 23000 FAX: +43 2622 23000-2711 Replace the HPP driving Gear Inspect the camshaft and the camshaft gear Remove the parts according to the latest revision of manual, then the maintenance inlet/outlet camshaft Inspect the bearing those parts if Replace necessary inspect against the criteria provided in the MSB-E4-035 Inspect the cylinder head is the HPP Gear rev. AE1 or subsequent p/n E4A-30-000-201 -YES installed?
NO Perform an engine ground run (5min.
MTOP) Perform an engine ground run according to Maintenance Manual Remove of the HPP and inspect the gear Is the Gear in RELEASE -NO acceptable -YES- TO conditions? SERVICE First Issue Date Rev. No. Revision Date Page 11 Aug 2021 30 09 2021 18-22 © 2021 by Austro Engine GmbH - AUSTRIA - www.austroengine.at
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 19-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
2.2. ILLUSTRATIONS None.
2.3. MASS (WEIGHT) Not affected.
2.4. APPROVAL STATEMENT The techn ical content of this document is approved under the authority of the DOA ref.
EASA.21J.399.
3. PLANNING INFORMATION
3.1. MATERIAL & AVAILABILITY Quantity Part Description Part Number 1 HPP Drive Gear E4A-30-000-601 or E4A-30-000-201 Rev. AB.1 or E4A-30-000-201 Rev. AE.1 2 Gasket DIN7603-12x16x2.0 2 Gasket DIN7603-A12x16-AL 1 Holder wrench HPP AE300T012-1
Caution: The assembly wrench can be used for 100 cycles, after that the tool is not serviceable and must be scraped.
3.2. SPECIAL TOOLS No. Description Note 1 Holder wrench HPP This special tool is provided as part of this SB and it is limited to 100 cycles 2 Bearing extractor Refer to Figure 3 (not part of the service bulletin kit)
Figure 3 – Bearing Extractor
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 20-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
3.3. LABOR EFFORT 2 hours for a replacement of an acceptable gear, up to 16 hours for a replacement of a nonacceptable gear that requires additional part inspections and/or parts replacement. The exact time depends on the components that might require replacement and do not include the waiting time between correspondence.
4. REMARKS
NOTE:
o All measures must b e carried out by a cert ified engine station and certified engine mechanics.
o The accomplishment of the instructions shown under Section 2.1 must be confirmed in the respective engine log book.
o The accomplishment of the instru ctions must be carried ou t within the time of compliance according chapter 1.
o In case o f doubt please contact the Austro Engine GmbH – After S ales S upport (e-mail: service@austroengine.at; Tel: +43 2622 23000 2525).
o For credit inf ormation contact A ustro En gine G mbH – After Sales Support (e-mail: service@austroengine.at; Tel: +43 2622 23000 2525)
5. EXPLANATORY NOTES
5.1. SYMBOL EXPLANATION
CAUTION: Disregarding these special instructions and safety measures can cause damage to the engine or other components.
NOTE: Additional note or instruction for better understanding of an instruction
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 21-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
6. APPENDIX
HPP Wrench Cycles recording sheet Note:
For each cycle, mark a cross on the corresponding box. When 100 cycles are reached, discard the wrench.
1 Gear replacement (removal & installation) = 1 cycle 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 HPP Drive gear wrench p/n
Mandatory Service Bulletin No. MSB-E4-034/3 Austro Engine GmbH Rudolf-Diesel-Strasse 11 A-2700 Wiener Neustadt Tel: +43 2622 23000 FAX: +43 2622 23000-2711
First Issue Date Rev. No. Revision Date Page 11 Aug 2021 3 30 09 2021 22-22 © 2021 by Austro Engine GmbH – AUSTRIA – www.austroengine.at
Service Bulletin Execution Report Note:
Aircraft owner:
Aircraft Operator: If different from the owner Aircraft:
Aircraft Serial Number:
Aircraft Marks:
Engine (RH) s/n: For single engine a/c, fill only one row Engine (LH) s/n:
Flight Hours:
Service center: Company Name or reference of the person(s) p erforming the oil pump replacement Removed HPP Gear s/n: Refer to the figure below to identify the serial number NOTE: A scanned version of this form must be provided to service@austroengine.at NOTE: The original filled version of this form, must be packed with the removed gear, and provided to Austro Engine
Figure 4 – Gear s/n location