Copy · U.S. DOT/FAA - Service Bulletin · 59 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2011-0652; AD 2012-22-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '82a23402acf524de11a53b4d6cff0cb5a0201814bf34a8fb51aa29ef0cbc509d'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 1–12

GroupFuselage Number 22242 - 2243 22245 22248 22250 - 2251 22253 22255 - 2256 22258 - 2263 22288 - 2290 14001 - 4002

2. Spares Affected None.

B. Concurrent Requirements None.

C. Reason Two MD-80 operators, while doing an investigation for fuel leaks, reported five instances of cracking of the wing rear spar lower cap at the outboard flap, inboard drive hinge at station Xrs=164.000. Boeing has determined that cracks are the result of material fatigue from normal flap operating loads. No MD-90 failures have yet been reported but this is a fatigue issue and it was determined that MD-90s are also susceptible to cracking. Inspecting this area for cracks will stop any crack migration and ensure repairs are done before additional damage occurs. Installation of doublers or doing the spar cap splice will provide a permanent repair. If not corrected, fuel leaks and damage to the wing skin or other structure may occur, resulting in flight disruptions and possible loss of the structural integrity of the wing.

Revision 1 is sent to incorporate engineering released subsequent to original release of this service bulletin, which incorporates an option to do a splice repair of the upper and/or lower rear spar caps.

The data given in Information Notice MD90-57A026 IN 01 is included in this revision.

MD-80 Service History Landing CyclesFlight-Hours 32,958 to 39,33851,293 to 69,453 D. Description This service bulletin does Eddy Current Testing High Frequency (ETHF) inspection on the aft side of the left and right wing rear spar lower caps at station Xrs=164.000 for cracks and based on inspection results does as follows:

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 13 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Condition 1 (No Cracks)

1. Does repeat ETHF inspections.

Condition 2 (Crack 2.0 Inches or Shorter and Not in the Rear Spar Lower Cap Forward Horizontal Leg Radius)

1. Does ETHF inspection on the aft side of the left and/or right wing rear spar upper cap, as applicable, at station Xrs=164.000 for cracks and based on inspection results does as follows:

Condition 2a (No Crack in Rear Spar Upper Cap)

a. Do Option 1 or Option 2 Option 1

(1) Does doubler repair to rear spar lower cap in accordance with Service Rework Drawing J060271.

(2) Does repeat ETHF inspections of rear spar lower cap doubler repair.

Option 2

(1) Does splice repair to rear spar lower cap in accordance with Service Rework Drawing J060165.

(2) Does Eddy Current Testing Low Frequency (ETLF) and Ultrasonic (UT) inspections of rear spar lower cap splice repair.

Condition 2b (Crack 2.0 Inches or Shorter in Rear Spar Upper Cap)

a. Do Option 1 or Option 2.

NOTE: Operators can do Option 1 or Option 2 or any combination of Options 1 and 2.

Option 1

(1) Does doubler repair to rear spar upper and lower caps in accordance with Service Rework Drawing J060271.

(2) Does ETHF inspection of rear spar upper and lower cap doubler repairs.

Option 2

(1) Does splice repair to rear spar upper and lower caps in accordance with Service Rework Drawing J060165.

(2) Does ETLF and UT inspections of rear spar lower cap splice repair.

Condition 2c (Crack Longer than 2 Inches in Rear Spar Upper Cap)

a. Do Option 1 or Option 2.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 14 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Option 1

(1) Does splice repair to rear spar upper cap in accordance with Service Rework Drawing J060165 and doubler repair to rear spar lower cap in accordance with Service Rework Drawing J060271.

(2) Does ETHF inspections of rear spar lower cap splice repair.

Option 2

(1) Does splice repair to rear spar upper and lower caps in accordance with Service Rework Drawing J060165.

(2) Does ETLF and UT inspections of rear spar lower cap splice repair.

Condition 3 (Crack Longer than 2.0 Inches or Crack in the Rear Spar Lower Cap Forward Horizontal Leg Radius)

1. Does ETHF inspection on the aft side of the left and/or right wing rear spar upper cap, as applicable, at station Xrs=164.000 for cracks and based on inspection results does as follows:

Condition 3a (No Crack in Rear Spar Upper Cap)

a. Does splice repair to rear spar lower cap in accordance with Service Rework Drawing J060165.

b. Does ETLF and UT inspections of rear spar lower cap splice repair.

Condition 3b (Crack 2.0 Inches or Shorter in Rear Spar Upper Cap)

a. Do Option 1 or Option 2 Option 1

(1) Does doubler repair to rear spar upper cap in accordance with Service Rework Drawing J060271 and splice repair to rear spar lower cap in accordance with Service Rework Drawing J060165.

(2) Does ETHF inspection of rear spar upper cap doubler repair.

(3) Does ETLF and UT inspections of rear spar lower cap splice repair.

Option 2

(1) Does splice repair to rear spar upper and lower caps in accordance with Service Rework Drawing J060165.

(2) Does ETLF and UT inspections of rear spar lower cap splice repair.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 15 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Condition 3c (Crack Longer than 2.0 Inches in Rear Spar Upper Cap)

a. Does splice repair to rear spar upper and lower caps in accordance with Service Rework Drawing J060165.

b. Does ETLF and UT inspections of rear spar lower cap splice repair.

Revision 1 - No more work is necessary on the airplane(s) changed in accordance with the original issue of this service bulletin, however the repetitive inspections called for in the original issue are still required.

The work in this service bulletin is done in the maintenance zone(s) given below.

Affected Maintenance Zones ZoneModel 511, 611MD-90-30 E. Compliance The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin mandatory.

Table 1: Inspect Left and Right Wing Rear Spar Upper and Lower Caps for Crack at Station Xrs = 164.000 Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 10,000 flight cycles after the original issue date on this service bulletin.

Before the accumulation of 30,000 total flight cycles.

Do Eddy Current, High Frequency (ETHF) inspection of the left and right wing rear spar lower cap at station Xrs=164.000 in accordance with Accomplishment Instruction

3.B.

All airplanes 2,550 flight cycles.

--Do ETHF inspection of the left and right wing rear spar lower caps at station Xrs=164.000 in accordance with Accomplishment Instruction

3.B.

Condition 1:

No Crack Before further flight.

Do ETHF inspection of the left and/or right wing rear spar upper cap at station Xrs=164.000 in accordance with Accomplishment Instruction 3.B..

Condition 2:

Crack 2.0 Inches or Shorter and Not in the Rear Spar Lower Cap Forward Horizontal Leg Radius

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 16 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Table 1: Inspect Left and Right Wing Rear Spar Upper and Lower Caps for Crack at Station Xrs = 164.000 Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition --Before further flight.

Option 1:

Do doubler repair of rear spar lower cap in accordance with Accomplishment Instruction 3.B.

Condition 2a:

No Crack in Rear Spar Upper Cap.

AND 8,500 flight cycles.

-13,500 flight cycles after doubler repair.

Do ETHF inspection in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

OR --Before further flight.

Option 2:

Do splice repair in accordance with Accomplishment Instruction 3.B.

AND 3,000 flight cycles.

-20,000 flight cycles after splice repair.

Do Eddy Current, Low Frequency (ETLF) and Ultrasonic (UT) inspections in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

--Before further flight.

Option 1:

Do doubler repair of rear spar upper and lower caps in accordance with Accomplishment Instruction 3.B.

Condition 2b:

Crack 2.0 Inches or Shorter in Rear Spar Upper Cap.

(Operators may do Option 1 or Option 2 or any combination of Option 1 and 2.)

AND 8,500 flight cycles.

-13,500 flight cycles after doubler repair.

Do ETHF inspection in the repaired area of the rear spar upper and lower caps in accordance with Accomplishment Instruction 3.B.

OR --Before further flight.

Option 2:

Do splice repair of rear spar upper and lower caps in accordance with Accomplishment Instruction 3.B.

AND 3,000 flight cycles.

-20,000 flight cycles after splice repair.

Do ETLF and UT inspections in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 17 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Table 1: Inspect Left and Right Wing Rear Spar Upper and Lower Caps for Crack at Station Xrs = 164.000 Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition --Before further flight.

Option 1:

Do splice repair of rear spar upper cap and doubler repair of rear spar lower cap in accordance with Accomplishment Instruction 3.B.

Condition 2c:

Crack Longer than 2.0 Inches in Rear Spar Upper Cap.

AND 8,500 flight cycles.

-13,500 flight cycles after doubler repair.

Do ETHF inspection in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

OR --Before further flight.

Option 2:

Do splice repair of rear spar upper and lower caps in accordance with Accomplishment Instruction 3.B.

AND 3,000 flight cycles.

-20,000 flight cycles after splice repair.

Do ETLF and UT inspections in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

--Before further flight.

Do ETHF inspection of the left and/or right wing rear spar upper cap at station Xrs=164.000 in accordance with Accomplishment Instruction 3.B.

Condition 3:

Crack Longer than 2.0 Inches or Crack in the Rear Spar Lower Cap Forward Horizontal Leg Radius.

-Before further flight.

Do splice repair of rear spar lower cap in accordance with Accomplishment Instruction 3.B.

Condition 3a:

No Crack in Rear Spar Upper Cap.

AND 3,000 flight cycles.

20,000 flight cycles after splice repair.

Do ETLF and UT inspections in the repaired area of the lower rear spar cap in accordance with Accomplishment Instruction 3.B.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 18 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Table 1: Inspect Left and Right Wing Rear Spar Upper and Lower Caps for Crack at Station Xrs = 164.000 Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition --Before further flight.

Option 1:

Do doubler repair of rear spar upper cap and splice repair of rear spar lower cap in accordance with Accomplishment Instruction 3.B.

Condition 3b:

Crack 2.0 Inches or Shorter in Rear Spar Upper Cap.

AND 8,500 flight cycles.

-13,500 flight cycles after doubler repair.

Do ETHF inspection in the repaired area of the rear spar upper cap in accordance with Accomplishment Instruction 3.B.

AND 3,000 flight cycles.

-20,000 flight cycles after splice repair.

Do ETLF and UT inspections in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

OR --Before further flight.

Option 2:

Do splice repair of rear spar upper and lower caps in accordance with Accomplishment Instruction 3.B.

AND 3,000 flight cycles.

-20,000 flight cycles after splice repair.

Do ETLF and UT inspections in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 19 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

Table 1: Inspect Left and Right Wing Rear Spar Upper and Lower Caps for Crack at Station Xrs = 164.000 Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition --Before further flight.

Do splice repair of rear spar upper and lower caps in accordance with Accomplishment Instruction 3.B.

Condition 3c:

Crack Longer than 2.0 Inches in Rear Spar Upper Cap. AND 3,000 flight cycles.

-20,000 flight cycles after splice repair.

Do ETLF and UT inspections in the repaired area of the rear spar lower cap in accordance with Accomplishment Instruction 3.B.

F. Approval This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this service bulletin comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other approved Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this service bulletin.

In addition, the Manager of the FAA Los Angeles, Aircraft Certification Office approves the action (i.e.

inspection or modification or repair) defined in this service bulletin as a method of compliance to the requirements of Principle Structural Element (PSE) 57.11.02.2 for those areas of the PSE addressed by this service bulletin.

G. Manpower The table below shows an estimate of the task hours necessary to do the Inspection/change/repair for each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task hour data if necessary. The estimate does not include lost time. These are some examples of lost time:

— Time to adjust to the workplace — Time to schedule the work — Time to examine the work — Time to cure the materials — Time to make the parts — Time to find the tools.

— Time to make reference standards.

1. Use applicable table for Manpower as follows:

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 20 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

TABLE 1: NO CRACK Elapsed HoursTask HoursNumber of Persons Task

0.51.02Open Access

2.04.02Inspect

0.51.02Close Access

3.06.0TOTAL FOR EACH WING TABLE 2: DOUBLER REPAIR Elapsed HoursTask HoursNumber of Persons Task

0.51.02Open Access

2.04.02Inspect

0.51.02Open Access to Tanks

4.04.01Defuel

8.08.01Purge

100.0*200.0*2Repair

0.51.02Close Access

2.04.02Test

117.5*223.0*TOTAL FOR EACH WING * Actual task hours and elapsed hours for repair are contingent upon inspection results.

TABLE 3: SPLICE REPAIR Elapsed HoursTask HoursNumber of Persons Task

0.51.02Open Access

2.04.02Inspect

0.51.02Open Access to Tanks

4.04.01Defuel

8.08.01Purge

200.0*400.0*2Repair

0.51.02Close Access

2.04.02Test

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 21 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

TABLE 3: SPLICE REPAIR Elapsed HoursTask HoursNumber of Persons Task

317.5*423.0*TOTAL FOR EACH WING * Actual task hours and elapsed hours for repair are contingent upon inspection results.

H. Weight and Balance Changes Weight and balance changes affected by incorporation of this service bulletin are contingent upon the changes to each particular airplane. Weight data is to be computed by the operator by weighing parts removed and parts installed during this change. Necessary revisions should be made to the appropriate airplane weight and balance report.

I. Electrical Load Data Not changed.

J. References

1. Existing Data:

a. Non-Destructive Test Standard Practices Manual (NDTSPM) 01-00-01, 06-00-01, 06-10-01.001, Part 06, 06-20-01.

b. MD-90 Aircraft Maintenance Manual (AMM) 06-35-00, 06-36-00, 12-11-01, 27-00-00, 27-10-00, 27-50-00, 27-50-01, 27-60-00, 28-00-00, 28-11-00 , 29-00-00, 32-10-00, 57-20-03, 57-40-01.

c. MD90 Structural Repair Manual (SRM) 51-10-03, 51-10-05, 51-10-09, 51-20-00, 51-30-01, 51-30-02, 51-30-03, 51-30-05, 51-31-02, 51-40-00.

d. MD-90 Airworthiness Limitations Instructions (ALI), Principal Structural Element (PSE)

57.11.02.2.

2. Data supplied with this Service Bulletin:

No data is supplied with this service bulletin. To obtain the data necessary to support this service bulletin submit a data request to:

Data and Services Management MS D800-0019 3855 Lakewood Boulevard Long Beach, California 90846 Phone: (562) 593-6996 Fax: (562) 593-2001 E-mail: dse.boecom@boeing.com

a. Drawings:

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 22 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

ADCNDCN/REVSheetTitleDrawing No -CDWGEDDY CURRENT INSPECTION - WING

REAR SPAR TEMPORARY REPAIR STA Xrs=164.000 3668XXX

YUAEOSERVICE REWORK - WING REAR SPAR

CAP SPLICE SERVICE REWORK DWG J060165 WUAEO VUAEO ZUAEO AAUDWG

UTDWGSERVICE REWORK - TEMPORARY RE-

PAIR, WING REAR SPAR, STATION Xrs=164.000 J060271 --DWGINSPECTION, REAR SPAR - LOWER CAP AT Xrs=192.00 SN90570001 --DWGINSPECTION - REAR SPAR AFT TANG

SERVICE NDI DRAWING SN90570006

3. Installation Drawings Used in the Preparation of this Service Bulletin:

None.

K. Publications Affected

1. Publications:

None.

2. Damage Tolerance Based Structural Inspections:

Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected are contained in Paragraph 1.E., Compliance of this service bulletin.

L. Interchangeability and Intermixability of Parts Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 23 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: February 11, 2010 MD90-57A026Revision 1: February 23, 2011 24 of 59 BOEING SERVICE BULLETIN MD90-57A026

ALERTALERT

BLANK PAGE

Pages 25–36 of 59