Copy · FAA-2015-1982_Appendix SB_SBF28-28-059_APP01 - FOKKER · 27 pages

© Fokker. Filed by the FAA in regulations.gov docket FAA-2015-1982; AD 2015-26-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '1b98f059a7401a3aed70a3b71e7815feb6cf078d1b96271f9020bfa7e4b4e6ae'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 1–12
Page 13OCROpen in PDF

fokker Service Bulletin Fokker Services B.V.

Part 1: Installation of Improved Bonding Provisions for the Fuel Quantity Tank Unit (FQTU) no. 7 mounting flange and attachment screws.

(Applicable to Aircraft Serial Numbers 11003 thru 11241, 11991 and 11992 in POST SBF28-57-098 configuration) Perform steps (A) thru (E) for LH and RH Fuel Quantity Tank Unit.

NOTE: Care must be taken to observe the safety precautions detailed in MM chapter 28-11-00 (SERVICING).

Before removal of unit drain fuel if necessary. Drain until level is below unit hole.

A. Removal of Fuel Quantity Tank Unit (FQTU) no. 7.

(1) Remove and keep the attachment screws from FQTU no.7 mounting flange, at the position as indicated on drawing.

(2) Carefully pull the FQTU from the tank (do not disconnect electrical wiring from FQTU) and temporary hold FQTU in position. Refer to MM chapter 28-41-01.

CAUTION: CARE SHOULD BE TAKEN NOT TO SCRATCH, BEND OR

SCORE THE OUTER TUBE ASSEMBLY AS SUCH DAMAGE MAY NECESSITATE FQTU REPLACEMENT.

(3) Remove and discard the O-ring seal from the wing top skin mounting joint.

B. Application of surface treatment for Fuel Quantity Tank Unit (FQTU) no. 7 mounting flange.

(1) Rework surface treatment of the flange mounted area on the upper skin with Alodine 1200 in accordance with SRM chapter 51-10-4 for Alodine treatment. Use:

- AR Conversion coating pn Alodine 1200 C. Installation of Improved Bonding Provisions for Fuel Quantity Tank Unit (FQTU) no. 7 attachment screws.

Refer to drawing W69315 sheet 2 for rework of LH Fuel Quantity Tank Unit.

Refer to drawing W69385 sheet 2 for rework of RH Fuel Quantity Tank Unit.

(1) Prepare the bond surface of the FQTU attachment screws, at the position as indicated on drawing; in accordance with NC4.610/937 (refer to TH4 of SPM for instructions and materials).

NOTE: This bonding code applies to two screws holes; use the locations at the position as indicated on drawing.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been sup ct to the provisions of an agreement Reproduction or disclosure to third parties of this document or any part thereof, or the use of any inforn r purposes other tha resaid agreement, is not permitted except with the prior written permission of Fokker Services B.V Page 12 of 26

Page 14OCROpen in PDF

fokker Service Bulletin Fokker Services B.V.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(2) Remove dust and grease from the prepared area. Use:

- AR Solvent (white spirit) pn WHITE SPIRIT D. Prepare Fuel Quantity Tank Unit (FQTU) no. 7.

(1) If the aircraft is in the PRE SBF28-28-054 configuration, then examine the FQTU that must be installed, as follows:

(a) Ensure that the FQTU is "clean and free of any deposits and that the mounting holes are unobstructed".

(b) Make sure that the FQTU is not corroded, bent or broken.

(2) If the aircraft is in the POST SBF28-28-054 configuration, then do these steps:

(a) Make sure that the self-locking nuts including the washers below these nuts and the stud-ends are fully covered with a layer of the sealant.

(b) Make sure that the layer of sealant is not damaged.

(c) If the layer of sealant is damaged, then do these steps:

1 Make sure that the installation of the FQTU to the mounting-flange is tight.

2 If necessary, re-tighten the three self-locking nuts.

Replace the layer of sealant (PR 1422B) on the self-locking nuts including the washers below these nuts and the stud-ends, ref. MM chapter 20-20- E. Install Fuel Quantity Tank Unit (FQTU) no. 7.

(1) Fit a new O-ring seal, lubricated with Vaseline VV-P-236 or with fuel, in the groove of the FQTU mounting point. Use:

O-Ring pn AS3578-137

(2) Carefully insert the FQTU probe into the fuel tank.

(3) Align the six mounting holes and secure the probe with six retained screws that have been removed in step A. (1); refer to MM chapter 28-41-01. New screws are to be installed on the positions as indicated on drawing. Use:

Screw pn NAS1581C3T6

(4) Seal off the reduced countersink screw head level/flush to the skin surface to obtain an aerodynamic smooth finish. Use:

- AR Sealant pn PR 1782B Status: Revision: Released date: (Mmm ddly) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by F • Services B.V. to its custo Reproduction or disclosure to third parties of this document or any part thereof, or the use of any in for purposes other thar with the prior written permission of Fokker Services B.V.

Page 13 of 26

Page 15OCROpen in PDF

okker Service Bulletin Fokker Services B.V.

NOTE If more Parts of this Service Bulletin Appendix are accomplished at the same time than steps F. thru G. may be accomplished with similar tasks of other Parts.

F. Remove all tools, materials and equipment from the work area. Make sure that the area is clean.

G. Restore electrical power.

(1) Restore all electrical power (refer to MM, chapter 24-00-00).

(2) Remove the warning signs to tell persons:

"DO NOT CONNECT THE ELECTRICAL POWER" "DO NOT CONNECT THE BATTERIES".

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Reproducian orde cosue do fire pates el the document any pantal To of no use thany on t d bv Fokker Services B.V. to its customen ject to the provisions of an agreeme aforesaid agreement, is not permitted excep with the prior written permission of Fokker Services B Page 14 of 26

Page 16OCROpen in PDF

okker Service Bulletin Fokker Services B.V.

Part 2: Installation of Improved Bonding Provisions for the Refueling Line.

(Applicable to Aircraft Serial Numbers Mark 1000: 11003 thru 11061, 11991 and 11992 in PRE SBF28-28-026 configuration, and Mark 2000: 11053 in PRE SBF28-28-026 configuration) A. Get access to work area, remove and keep access panels 27A, 27B,28A and 28B (refer to MM, chapter 06-30).

B. Installation of Improved Bonding Provisions for the Refueling Line.

Refer to figure 1 or 2 for rework of the Refueling Line.

Figure 1 is applicable for standard Mark 1000 and Mark 2000 aircraft.

Figure 2 is applicable for Mark 1000 aircraft equipped with Centre Wing Tank.

(1) Remove and discard clamp pn AN742-D28 and attached parts at the positions as indicated as "View A" in figure 1 or 2.

(2) Rework and prepare the bond surface for the clamp on the pressure fuelling line (or centre wing tank fuel supply line if equipped with Centre Wing Tank) on rear spar of centre wing, at the positions as indicated as "View A" in figure 1 or 2, in accordance with NC4.610/905 (refer to TH4 of SPM for instructions and materials).

Clamp pn FON2-7313-28

- 1 Screw pn MS27039-1-09

- 1 Washer (cupal) pn FON2-3306-5A Washer pn NAS1252-10L

- 1 Lead pn FON9-1901C80C NOTE: All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

NOTE: The NC4.610/905 bonding design build-up is as follows:

screw, washer, clamp, bonding lead, cupal washer and anchor nut.

CAUTION: BE SURE THAT THE CUPAL WASHERS ARE INSTALLED WITH

THE COPPER SIDE OF THE CUPAL WASHERS AGAINST THE BONDING LEAD TERMINAL.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rig! I B.V. to its c ect to the provisions of an agreement art thereof. or the use of any in resaid agreement, is not permitted except Page 15 of 26

Page 17OCROpen in PDF

Fokker Service Bulletin Fokker Services B.V.

(3) Rework and prepare the bond surface for the bonding clamp on the pressure fuelling line (or centre wing tank fuel supply line if equipped with Centre Wing Tank) on rear spar of centre wing, at the positions as indicated as "View A" in figure 1 or 2, in accordance with NC4.610/910 (refer to TH4 of SPM for instructions and materials). Use:

- 1 Clamp pn AN735-D28 pn NAS1291-3 pn MS27039-1-07

- 2 Washer pn NAS1252-10L NOTE: All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(4) Remove and discard clamp pn AN742-D28 and attached parts at the position as indicated as "View B" in figure 1 or 2.

(5) Rework and prepare the bond surface for the clamp on the pressure fuelling line (or centre wing tank fuel supply line if equipped with Centre Wing Tank) on rear spar of centre wing, at the position as indicated as "View B" in figure 1 or 2, in accordance with NC4.610/920 (refer to TH4 of SPM for instructions and materials).

pn FON2-7313-28 pn MS27039-1-09 pn NAS1252-10L All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

Steps (6) thru (8) are only applicable for standard Mark 1000 and Mark 2000 aircraft.

(6) Remove and discard clamp pn AN742-D28 and attached parts at the position as indicated as "View C" in figure 1.

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 s B.V. to its c ons of an agre ed by the aforesaid agreement, is not permitted excep Page 16 of 26

Page 18OCROpen in PDF

fokker Service Bulletin Fokker Services B.V.

(7) Rework and prepare the bond surface for the clamp on the pressure fuelling line on rear spar of centre wing, at the position as indicated as "View C" in figure 1, in accordance with NC4.610/905 (refer to TH4 of SPM for instructions and materials).

Use:

Clamp pn FON2-7313-28

- 1 Screw pn MS27039-1-09

- 1 Washer (cupal) pn FON2-3306-5A Washer pn NAS1252-10L

- 1 Lead pn FON9-1901C80C NOTE All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

NOTE: The NC4.610/905 bonding design build-up is as follows:

screw, washer, clamp, bonding lead, cupal washer and anchor nut.

CAUTION: BE SURE THAT THE CUPAL WASHERS ARE INSTALLED WITH

THE COPPER SIDE OF THE CUPAL WASHERS AGAINST THE BONDING LEAD TERMINAL.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(8) Rework and prepare the bond surface for the bonding clamp on the pressure fuelling line on rear spar of centre wing, at the position as indicated as "View C" in figure 1, in accordance with NC4.610/910 (refer to TH4 of SPM for instructions and materials). Use:

Clamp pn AN735-D28

- 1 Nut pn NAS1291-3

- 1 Screw pn MS27039-1-07

- 2 Washer pn NAS1252-10L NOTE: All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

Steps (9) thru (11) are only applicable for Mark 1000 aircraft equipped with Centre Wing Tank.

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Fokker Services B.V. (The Netherlands) This document has been supplied ices B.V. to its cu subject to the provisions of an agreement Reproduction or disclosure to third parties of this document or any part thereof, or the use of any inform r purposes oth foresaid agreement, is not permitted excep with the prior written permission of Fokker Services B.V.

Page 17 of 26

Page 19OCROpen in PDF

okker Service Bulletin Fokker Services B.V.

(9) Remove and discard clamp pn AN742-D16 and attached parts at the position as indicated as "View C" in figure 2.

(10) Rework and prepare the bond surface for the clamp on the centre wing tank fuel supply line on rear spar of centre wing, at the position as indicated as "View C" in figure 2, in accordance with NC4.610/905 (refer to TH4 of SPM for instructions and materials). Use:

Clamp pn FON2-7313-18

- 1 Screw pn AN3-4A

- 1 Washer (cupal) pn FON2-3306-5A Washer pn NAS1252-10L Lead pn FON9-1901C100C NOTE: All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

NOTE: The NC4.610/905 bonding design build-up is as follows:

screw, washer, clamp, bonding lead, cupal washer and anchor nut.

CAUTION: BE SURE THAT THE CUPAL WASHERS ARE INSTALLED WITH

THE COPPER SIDE OF THE CUPAL WASHERS AGAINST THE BONDING LEAD TERMINAL.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(11) Rework and prepare the bond surface for the bonding clamp on the centre wing tank fuel supply line on rear spar of centre wing, at the position as indicated as "View C" in figure 2, in accordance with NC4.610/910 (refer to TH4 of SPM for instructions and materials). Use:

- 1 Clamp pn AN735-D18

- 1 Screw 1 Nut pn NAS1291-3 pn MS27039-1-07 2 Washer pn NAS1252-10L NOTE: All electrical contact areas should be cleaned before, and painted after installation of the applicable parts, in accordance with F28 Maintenance Manual, chapter 20-40-2.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Foki This document has been supplied by ervices B.V. to its cus ect to the provisions of an agreeme reproducen or discosure o my pares or ma det for purposes omen ma aid agreement, is not permitted excep Page 18 of 26

Page 20OCROpen in PDF

fokker Service Bulletin Fokker Services B.V.

(12) Remove dust and grease from the prepared area. Use:

- AR Solvent (white spirit) pn WHITE SPIRIT NOTE If more Parts of this Service Bulletin Appendix are accomplished at the same time than steps C. thru E. may be accomplished with similar tasks of other Parts.

C. Remove all tools, materials and equipment from the work area. Make sure that the area is clean.

D. Install access panels.

(1) Install access panels 27A, 27B, 28A and 28B (refer to MM, chapter 06-30).

E. Restore electrical power.

(1) Restore all electrical power (refer to MM, chapter 24-00-00).

(2) Remove the warning signs to tell persons:

DO NOT CONNECT THE ELECTRICAL POWER" "DO NOT CONNECT THE BATTERIES".

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 pyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has b production or disclosure to third parties of this document or any part thereof, or the use of with the prior written permission of Fokker Services B.V.

applied by Fokker Services B.V. to its customers on a confidential basis subject to the provisions of an agreemen therein for purposes other than explicitly allowed by the aforesaid agreement, is not permitted excep Page 19 of 26

Page 21OCROpen in PDF

okker Service Bulletin Fokker Services B.V.

Part 3: Installation of Improved Bonding Provisions for the Suction Relief Valve line.

(Applicable to Aircraft Serial Numbers 11016 thru 11061, 11991 and 11992, in POST SBF28-28-020 configuration, and Aircraft Serial Numbers 11062 thru 11241 if equipped with Center Wing Tanks) A. Get access to work area, remove and keep access panels 91K and 92K (refer to MM, chapter 06-30).

NOTE: If access to the Suction Relief Valve line is found insufficient, remove and keep access panels 91J and 92J (refer to MM, chapter 53-50-02).

B. Installation of Improved Bonding Provisions for the Suction Relief Valve line.

Refer to drawing W69711 sheet 1 for rework of LH and RH Suction Relief Valve line.

Perform steps (1) thru (4) for LH and RH Suction Relief Valve line.

(1) Rework and prepare the bond surface for the clamp on the Suction Relief Valve line, at the position as indicated in drawing W69711 sheet 1, in accordance with NC4.610/905 (refer to TH4 of SPM for instructions and materials). Use:

pn NAS1100-3-8

- 1 Washer (cupal) pn FON2-3306-05010

- 1 Washer pn NAS1149D0332K

- 1 Lead pn FON9-1901C200C All electrical bonds must be sealed in accordance with SPM NC4.610;

5.3, Finishing Requirements

5.6, Finishing with Sealing Compound.

CAUTION BE SURE THAT THE CUPAL WASHERS ARE INSTALLED WITH

THE COPPER SIDE OF THE CUPAL WASHERS AGAINST THE BONDING LEAD TERMINAL.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(2) Rework and prepare the bond surface for the bonding clamp on the Suction Relief Valve line, at the position as indicated in drawing W69711 sheet 1, in accordance with NC4.610/910 (refer to TH4 of SPM for instructions and materials). Use:

- 1 Clamp pn AN735-D16

- 1 Nut pn MS21042L3

- 1 Screw pn NAS1133-3

- 2 Washer pn NAS1149D0332K NOTE: All electrical bonds must be sealed in accordance with SPM NC4.610;

5.3, Finishing Requirements Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Fol ices B.V, to its c the feat here, not pan ade r purposes other than explicitly allowed by with the prior witten permis Page 20 of 26

Page 22OCROpen in PDF

tokker Service Bulletin Fokker Services B.V.

5.6, Finishing with Sealing Compound.

CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(3) Apply a fillet sealant on the installed screws, washers, nut and clamp, installed in steps (1) and (2), in accordance with SRM chapter 51-20-0. Use:

- AR Sealant pn PR 1422A

(4) Remove dust and grease from the prepared area. Use:

- AR Solvent (white spirit) pn WHITE SPIRIT NOTE: If more Parts of this Service Bulletin Appendix are accomplished at the same time than steps C. thru E. may be accomplished with similar tasks of other Parts.

C. Remove all tools, materials and equipment from the work area. Make sure that the area is clean.

D. Install access panels.

(1) Install access panels 91K and 92K (refer to MM, chapter 06-30).

(2) Install access panels 91J and 92J, if removed (refer to MM, chapter 06-30).

E. Restore electrical power.

(1) Restore all electrical power (refer to MM, chapter 24-00-00).

(2) Remove the warning signs to tell persons:

"DO NOT CONNECT THE ELECTRICAL POWER" "DO NOT CONNECT THE BATTERIES".

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Fokker Services B V. (The Netherlands) This document has been supp vices d.V. to as customers on a condi subject to the provisions of an agreemer Wep the phor wor on perre son of Forker of vices sument or any part thered, or the use of any infor r purposes other than explicitly allowed by the aforesaid agreement, is not permitted excep Page 21 of 26

Page 23OCROpen in PDF

fokker Service Bulletin Fokker Services B.V.

Part 4: Installation of Improved Bonding Provisions for Boost Pump attachment screws.

(Applicable to Aircraft Serial Numbers 11003 thru 11241, 11991 and 11992).

A. Installation of Improved Bonding Provisions for Boost Pump attachment screws.

Refer to drawing W69205 sheet 1 for rework of LH Boost Pump.

Refer to drawing W69245 sheet 1 for rework of RH Boost Pump.

Perform steps (1) thru (6) for LH and RH Boost Pumps.

(1) Remove and discard the 2 screws from the front and rear Boost Pump attachment, at the positions as indicated on drawing.

NOTE: The bonding locations are also engraved in the Boost Pump flange by the manufacturer. The paint scheme may/can cover these engravings. When not visible, use the locations indicated on the drawings.

(2) Rework and prepare the bond surface of the screw holes for the front and rear Boost Pump, at the positions as indicated on drawing, in accordance with NC4.610/937 (refer to TH4 of SPM for instructions and materials).

NOTE This bonding code applies to two screws holes; use the positions as indicated on drawing CAUTION: INSTALL THE CONNECTION IMMEDIATELY AFTER THE

CONTACT SURFACE IS CLEANED, TO PREVENT CORROSION OF THE CONTACT SURFACES.

DO NOT TOUCH THE CLEANED SURFACE WITH A BARE

HAND, THE SEALING COMPOUND WILL NOT BOND TO A GREASY SURFACE.

(3) Remove dust and grease from the prepared area. Use:

- AR Solvent (white spirit) pn WHITE SPIRIT

(4) Install new screws (reduced- head) for front Boost Pump (refer to MM, chapter, 28-22-02). Use:

- 2 Screw pn NAS1581C3T10

(5) Install new screws (reduced- head) for rear Boost Pump (refer to MM, chapter, 28-22-02). Use:

- 2 Screw pn NAS1581C3T14

(6) Seal off the reduced countersink screw head level/flush to the skin surface to obtain an aerodynamic smooth finish. Use:

- AR Sealant pn PR 1782 Class A NOTE If more Parts of this Service Bulletin Appendix are accomplished at the same time than steps B. and C. may be accomplished with similar tasks of other Parts.

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights rese ervices B.V. to its cus said agreement, is not permitted excep Page 22 of 26

Page 24OCROpen in PDF

okker Service Bulletin Fokker Services B.V.

B. Remove all tools, materials and equipment from the work area. Make sure that the area is clean.

C. Restore electrical power.

(1) Restore all electrical power (refer to MM, chapter 24-00-00).

(2) Remove the warning signs to tell persons:

"DO NOT CONNECT THE ELECTRICAL POWER" "DO NOT CONNECT THE BATTERIES".

Status: Revision: Released date: (Mmm dd/yy) Released Jul 15/14 Security class: • F28 Appendix SB no.:

UNCLASSIFIED SBF28-28-059/APP01 Copyright All rights reserved by Fokker Ser ands) This document has been supp ed by Fokker Services B.V. to its customers on a co ibiect to the provisions of an agreeme Reproduction or disclosure to third parties with the prior written permission of Fokker S Page 23 of 26

Pages 25–27 of 27