AC 120-111

Change 1Historical

Advisory circular · Upset Prevention and Recovery Training

A newer version is currentThis is a historical version. AC 120-111 CHG 1 Ed Update 3 is the version in force, approved September 6, 2024.
Approved
January 4, 2017
Last reviewed
August 27, 2024
This change
CHG 1 to AC 120-111.
Cancels
AC120-111
Cancelled by
AC120-111 CHG 1 Ed Update
Family
AC 120-111 · 5 versions
Revision
change 1
14 CFR parts
121, 61
Cited by
1 AD

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 22, 2025.

Show pages 13–24

Par 4-2 Page 19 TABLE 3. NOSE HIGH RECOVERY TEMPLATE WITH EXPLANATION (CONTINUED) RECOVER to level flight9 when airspeed is sufficiently increasing:

Explanation: Recover to slightly nose-low attitude to reduce the potential for entering another upset. Roll to wings level, if necessary, as the nose approaches the horizon. Check airspeed, and adjust thrust and pitch as necessary.

Pilot Monitoring MONITOR airspeed and attitude throughout the recovery and ANNOUNCE any continued divergence.

Explanation: Evidence shows that the PM is often in a better position than the PF to recognize adverse trends in airplane state or flight parameters.

9 Avoid stall because of premature recovery or excessive G loading.

Par 4-2 Page 20 TABLE 4. NOSE LOW RECOVERY TEMPLATE WITH EXPLANATION Either Pilot:

Recognize and confirm the developing situation. Announce: “Nose Low” Explanation: A critical element in recognition and confirmation is to clearly understand the energy state and the rate to which it is changing because this will have an effect on how the PF handles the recovery.

Pilot Flying AP: DISCONNECT10 A/THR: OFF Explanation: Leaving the autopilot or autothrottle/autothrust connected may result in inadvertent changes or adjustments that may not be easily recognized or appropriate, especially during high workload situations.

RECOVER from stall if required Explanation: Even in a nose-low, low-speed situation, the airplane may be stalled at a relatively low pitch. It is necessary to recover from the stall first. This may require nose-down elevator, which may not be intuitive.

ROLL11 in the shortest direction to wings level.

Explanation: Full aileron and spoiler input may be necessary to smoothly establish a recovery roll rate toward the nearest horizon. It is important that positive G force not be increased or that nose-up elevator or stabilizer trim be used until the airplane approaches wings level. It may be necessary to unload the airplane by decreasing backpressure to improve roll effectiveness. If the airplane has exceeded 90° of bank, it may feel like “pushing” in order to unload. It is necessary to unload to improve roll control and to prevent pointing a large lift vector towards the ground.

THRUST and DRAG: Adjust (if required) Explanation: If airspeed is low, apply thrust; if airspeed is high, reduce thrust, and if necessary, extend speedbrakes.

RECOVER to level flight12 Explanation: Complete the recovery by establishing a pitch, thrust, and airplane drag device configuration that corresponds to the desired airspeed.

10 A large out-of-trim condition could be encountered when the AP is disconnected.

11 It may be necessary to reduce the G loading by applying forward control pressure to improve roll effectiveness.

12 Avoid stall because of premature recovery or excessive G loading.

Par 4-2 Page 21 (and 22) TABLE 4. NOSE LOW RECOVERY TEMPLATE WITH EXPLANATION (CONTINUED) Pilot Monitoring MONITOR airspeed and attitude throughout the recovery and ANNOUNCE any continued divergence.

Explanation: Evidence shows that the PM is often in a better position to recognize adverse trends in airplane state or flight parameters than the PF.

NOTE: Recovery to level flight may require use of pitch trim.

WARNING: Excessive use of pitch trim or rudder may aggravate the upset situation or may result in high structural loads.

Page 29 · 1Open in PDF

Appendix 1 APPENDIX 1. TRAINING ELEMENTS AND EVENTS

1. Aerodynamics Academic a.

b.

c.

General Aerodynamics:

• Aerodynamic flight envelope.

• Load factor.

• Directional and lateral control.

• Weight and balance effects on handling.

• Trim.

• Sideslip.

Advanced Aerodynamics:

• Lift versus drag (L/D) curve, L/D Max in particular, and significance on airplane performance in general.

• Relationship between L/D curve and airspeed.

• Airplane energy state and its application in various flight altitudes, airspeeds, and attitudes.

• Optimum climb speed, crossover altitude, optimum altitude, and maximum altitude as they relate to airplane performance and the effect of deviations (environmental or airplane) on performance.

• Thrust required versus thrust available.

• Thrust-limited conditions and recovery.

• Aerodynamic stability and its effects in flight including maneuvering stability and characteristics at high and low altitude;

environmental impact on aerodynamics and handling

(e.g., temperature, ice, etc.).

Airplane Performance (high and low altitude):

• Use of airplane (type-specific) performance charts to determine the effects of environmental, airplane configuration, or system changes on planned flight performance.

• Training pilots to understand that an airplane may not be able to reach its maximum certified altitude depending on performance at the time of the flight is critical. Pilots should also understand the possible consequences of choosing a cruising altitude that exceeds the airplane’s performance capabilities for the conditions existing at the time of the flight.

• Recognition of the different flight deck cues between low-speed buffet and high-speed buffet.

Page 30 · 2Open in PDF

Appendix 1

d.

e.

Type-specific aerodynamics:

• Angle of Attack (AOA) awareness including:

• Importance of AOA as it relates to airplane performance and wing stall angle.

• Effect of airplane configuration (e.g., flaps, gear, leading edge slats, speedbrakes, and thrust/power setting) on stall margins and stall characteristics.

• AOA relationship to various airplane systems, particularly warning systems (e.g., stall warning, stick shaker, stick pusher, etc.).

• General and airplane-specific AOA knowledge.

• Impact of environmental and system factors on AOA indications and their relationship to the stall AOA and various airplane warning systems (e.g., type-specific knowledge of the stall warning system).

• AOA indications, if presented to the pilot.

• Airplane-specific handling to use AOA-derived information to prevent or recover from an upset (including stall).

Mach effects including:

• Mach tuck and Mach buffet and the reason for them.

• Buffet-limited max altitude.

• Critical Mach number and aerodynamic forces acting on the wing at critical Mach.

• Control surface effectiveness at high speed.

NOTE: Training for AOA and Mach effects should only be accomplished to the extent of their applicability to the specific airplane.

Flight The FSTD training should be accomplished at both high altitudes (within 5,000 ft. of the service ceiling of the airplane), and low altitude (below 10,000 ft. above ground level (AGL)). Use of normal operational cruise altitudes for high-altitude training should be encouraged. To fully understand the concepts discussed in academic training, pilots should demonstrate the following:

• Recognize buffet (if applicable to airplane type), when encountered.

• Maneuvering at high altitudes at various speeds and automation levels applying the aerodynamic principles studied to prevent an upset.

• Awareness of the AOA from available data shown on the flight deck (e.g., barber pole on speed tape, pitch-limit-indicator, flight-path-symbol relative to pitch attitude, etc.) and demonstrate the use of those data to prevent an upset or recover from one.

Page 31 · 3Open in PDF

Appendix 1

• Demonstrate knowledge of the type-specific systems that use AOA inputs with emphasis on warning systems and the limitations of those systems.

• Speed controlled by elevator inputs or speed controlled by thrust, airplane energy state as it pertains to the type being flown, and demonstrate use of that knowledge to prevent or recover from an upset.

• Roll rate performance of the airplane at different speeds and different configurations and with flight spoilers retracted/extended if a difference exists.

• Pitch rate performance of the airplane at different speeds, different configurations, and with flaps retracted/extended.

• Demonstrate an aft center of gravity (CG) versus forward CG if flight qualities are significantly different.

Additional details regarding these areas can be found in the Airplane Upset Recovery Training Aid (AURTA) Revision 2, section 2.5. While the AURTA was designed for swept-wing airplanes with more than 100 seats, the general concepts are still applicable to most high-performance airplanes.

2. G Awareness Academic The effects of g’s, especially during airplane upsets. Emphasize that G-loading in transport category airplanes feels significantly more pronounced than in simulation. Airline pilots are normally uncomfortable (for the sake of passenger comfort and safety) with aggressively loading or unloading the G forces on a large passenger airplane. This inhibition must be overcome when faced with the necessity to quickly and sometimes aggressively maneuver the airplane. Most FFSs cannot replicate sustained load factors greater or less than 1g; therefore, the flight deck situation must be envisioned during flight different from 1g. The pilot may feel significantly heavier or lighter in the seat for moderate durations. It may be difficult to reach the rudder pedals. Unsecured items may be flying around the flight deck. However, it should be emphasized that it should not normally be necessary to maneuver at less than 0g.

Flight Incorporated into section 8 Upset Recovery Techniques below.

3. Energy Management Academic • The interrelationship between kinetic energy (airspeed), potential energy (altitude), and chemical energy (power).

• How the airplane gets in a high- or low-energy state and the input options available to change the energy state to a stable and safe state.

• How external factors can change energy state and how to correct for them.

Page 32 · 4Open in PDF

Appendix 1

• What parameters to focus on to decide an appropriate response;

crosscheck with the other pilot to establish a shared understanding.

• What to monitor during an event and how the pilot monitoring (PM) should assist the pilot flying (PF) in the recovery using appropriate callouts and other verbal feedback.

Flight This training should include integrated Crew Resource Management (CRM) training for developing crew knowledge and skills for energy management and techniques for reducing pilot error. To fully understand the concepts discussed in academic training, pilots should demonstrate the following:

• Acceleration between two speeds of which the airplane is capable at low altitude, medium, and high altitude (e.g., accelerating between 200 and 250 knots at low altitude and high altitude, which corresponds to Mach changes at high altitude) to demonstrate changes in available thrust.

• Acceleration performance from region of reversed command (back side of power curve) at low altitude and high altitude.

• The relationship between Maximum Cruise/Climb/Continuous Thrust and takeoff/go-around (TOGA) power settings at high altitude.

• Acceleration capabilities through descent versus power application.

• Wake vortex encounter behind a heavy airplane in takeoff and approach configuration.

4. Flightpath Management Academic Flightpath and energy management systems: Pilots should have a thorough understanding of the normal operation, failure modes and effects, and system integration effects of flightpath and energy management systems. Training on flightpath and energy management systems should include:

• Normal system operation and limitations.

• Indications and modes, including crosscheck and verification of mode use and understanding of how a specific mode will command the airplane; interoperability with other systems.

• Failure modes and effects.

• Common model-specific failures.

• Common errors to avoid and why they occur.

• The importance of ensuring correct inputs to the automated systems for flightpath management and the consequences of failing to do so.

• Understanding of type-specific characteristics to prevent inadvertent LOC-I events because of automation surprise

(e.g., vertical speed (VS) or indicated airspeed (IAS) modes based on altitude).

Page 33 · 5Open in PDF

Appendix 1

• System review when conducting recurrent training.

• Knowledge of pitch attitudes, power settings, and airspeeds for common configurations and different phases of flight, as applicable to the airplane type.

Manual Flight Operations:

• Primary and alternate control strategies.

• Nonintuitive factors. For example, it may be counterintuitive to use greater unloading control forces when recovering from a high AOA, especially at low altitudes.

• Additionally, for under-wing-mounted engines it may be necessary to reduce thrust in order to reduce the AOA due to the strong pitch up forces from added thrust.

• Specific aspects of the transition from automated to manual flight including transition from using a flight director to “raw data,” as applicable.

Flight Training should include abnormal operating conditions, reliance on primary flight instruments, manual flying skills, and edge-of-envelope operating conditions that could be encountered during routine operations.

Examples include:

• Takeoff at high weight and aft/forward CG limits.

• Recognition and recovery from low-airspeed/energy condition in approach/landing configuration.

• Recognition and recovery from low-airspeed/energy condition near the service ceiling.

• Climb-to, steady state, and descent from service ceiling.

• Unplanned transition from automated to manual flight, including transition from using a flight director to “raw data,” as applicable.

5. Causes and Contributing Factors of Upsets Academic • Environmentally induced upsets, which could be caused by turbulence, mountain wave, wind shear, thunderstorms, microbursts, or airplane icing.

• Pilot-induced upsets which could be caused by misinterpretation or slow instrument crosscheck, improper adjustment of attitude and power, improper pilot input, inattention, distractions, spatial disorientation, pilot incapacitation, misunderstanding of autoflight modes or improper use of automated systems, transition from automated to manual modes due to system disconnect, and pilot-induced oscillation (PIO).

• Mechanically induced upsets that could be caused by flight instrument anomalies/failures, autoflight anomalies/failures, flight control malfunctions/failures, or other system anomalies.

• Common illusions (e.g., somatogravic illusion, the leans, Coriolis illusion, etc.) associated with LOC-I events. It should be explained

Page 34 · 6Open in PDF

Appendix 1 why they occur and the importance of following procedure to avoid susceptibility to illusions.

• Situations resulting in an upset due to a lack of visual cues such as a sub-threshold roll (i.e., imperceptible roll rate, generally less than three degrees per second).

Flight Not applicable

6. Review of Accidents and Incidents Relating to Airplane Upsets Academic Review of accidents and incidents related to transport category airplane upsets with focus on an understanding of the events leading to the upset, proper or improper decisionmaking actions that contributed to the upset, and, if applicable, recovery. Aviation Safety Action Program (ASAP), Flight Operational Quality Assurance (FOQA), and Aviation Safety Reporting System (ASRS) data can also support this discussion.

Flight Not applicable

7. Recognition Academic a. Type-specific examples of instrument indications during developing and developed upset.

• Visual representations of the outside view and type-specific instrument indications of a variety of developing and developed upset conditions, with a focus on pitch, power, roll, and speed trend. Pilots should be provided context for each event in order for them to identify the divergence.

• Some normal situations should also be included so pilots can identify what is normal versus what is not.

• If applicable, discuss other cues, such as audio or buffet cues.

b. Pitch/Power/Roll/Yaw

• Pilots must have a fundamental understanding of instrumentation and flight dynamics in pitch, power, roll, and yaw in order to recognize the current state of the airplane and make the correct control inputs to arrest the divergence or recover from the upset.

• The use of the AURTA Revision 2, sections 2.5.5.5–2.5.5.9, is recommended for specific details for training Pitch/Power/Roll/Yaw.

c. Effective Scanning

• Effective instrument scanning techniques should be trained, as appropriate, to recognize normal states and divergence from normal flight parameters.

• To prevent flightpath divergences related to improper monitoring of airplane state, pilots should be trained during all phases of flight on what to monitor and when, crosschecking, and verification.

Page 35 · 7Open in PDF

Appendix 1

d. CRM techniques for working as a crew to return the airplane to normal flight and communicating airplane state between pilots, including CRM callouts to improve situational awareness.

• Evidence shows that the PM is often in a better position to recognize adverse trends in airplane state or flight parameters than the pilot flying (PF).

• The PM should be tasked with active monitoring of aircraft state and flight parameters and prompt callout of any divergence from planned and/or briefed flightpath.

Flight The academic principles of recognition should be continuously reinforced by the instructor during flight training.

8. Upset Recovery Techniques Academic • Emphasize timely and appropriate intervention.

• Emphasize that recovery to a stabilized flightpath should be initiated as soon as a divergence from intended flightpath is recognized.

• Emphasize the need for the PF or PM to recognize a divergence as early as possible, and immediately ensure corrective action is taken to return the airplane to a stabilized flightpath rather than waiting until the airplane has developed into an established upset.

• The use of an intervention strategy employed by the PM that progresses from alerting the PF of a divergence from the intended flightpath, to suggesting a course of action (advocacy and assertion), and proceeds to directly intervening by taking the controls to prevent an accident or incident. In the event that a pilot intervenes by taking control of the airplane, he should announce the transfer of control.

• The attitude direction indicator (ADI), attitude display of the primary flight display (PFD), or head-up display (HUD), as applicable, is the primary control instrument for recovery from an upset.

• Due to varying visibility conditions, pilots cannot depend on having adequate outside visual references.

• Air carriers and Original Equipment Manufacturers (OEM) may already have policies on how to handle minor divergence from the desired flightpath for items such as bank, airspeed, heading, etc., including callouts. The intent of these procedures or CRM techniques is for the PM to draw attention to any divergence that exceeds parameters set by the company and for the PF to take corrective action.

• Control inputs to counter a developing upset must be smooth, positive, and proportional to the amount and rate of pitch, roll, or yaw experienced.

Page 36 · 8Open in PDF

Appendix 1

• Up to full-scale control deflections may be necessary; however, initiating recovery with arbitrary full-scale control deflections could aggravate the situation. An aircraft’s response to excessive or inappropriate control input that overshoots the desired response can startle or surprise the pilot and cause one upset to lead to another.

The use of the AURTA Revision 2, sections 2.6.3.2–2.6.3.5, is recommended for details to train the academic portion of the recovery techniques for the four elements below. For instructional purposes, the AURTA Revision 2 addresses several different airplane upset situations (listed below). This provides the basis for relating the aerodynamic information and techniques to specific situations.

• Nose-High/Wings-level recovery.

• Nose-Low/Wings-level recovery.

• High Bank-Angle Recovery Techniques.

• Consolidated Summary of Airplane Recovery Techniques.

Flight The nose-high and nose-low maneuvers in Chapter 4, Tables 1 and 2, should be practiced first in maneuver-based training, followed by Scenario-Based Training (SBT). For the recovery from the nose-high upset, pilots are instructed to push to achieve less than 1g.

NOTE: Rudder control is still effective at a high AOA, and special care must be taken in the use of rudder during upset prevention and recovery. It is important to guard against control reversals. To maintain structural integrity, avoid rapid full-scale reversal of control deflections.

During this training, the instructor should:

• Use the Instructor Operating Station (IOS) to track G-load and other flight parameters during recovery;

• Provide specific feedback if recovery was too aggressive,

i.e., structural or other flight limits were exceeded during recovery;

• Provide specific feedback if recovery was insufficiently positive,

i.e., recovery was delayed or impaired due to insufficient control inputs;

• Provide specific feedback if recovery control inputs were excessive, or cyclic with control reversals; and

• After the pilot uses the correct amount of force to recover, note that the absence of G-load sensing in the FSTD may lead to a tendency to undercontrol recovery in the actual aircraft when these loads are sensed.