U.S. Department of Transportation Federoi Aviation Administration Advisory Circular Subject: GROUND DEICING AND ANTI-ICINGDBle: 12/12jg4 TRAINING AND CHECKING Initiated by: ~~~-250 AC No: 13546 Change:
1 PURPOSE. This advisory circular (AC) provides one means, but not the only means, of complying with Federal Aviation Regulations (FAR) Sections 135.227, 135.345, and 135.351 (referred to as the FAR Part 135 ground deicing rule), Specifically, the guidance in this AC concerns:
a. Ground deicing and anti-icing training requirements that should be incorporated into an approved training program for certain air carriers;
b Ground deicing and anti-icing guidance for those air carriers that are not required to have an approved training program; and C. The pretakeoff contamination aircraft check required of all FAR Part 135 air carriers except those that develop an approved alternative procedure or comply with the FAR Part 121 ground deicing rule contained in FAR Section 121.629(c).
2 l RELATED FAR SECTIONS.
a. Part 135, Subpart A - General. Sections 135.23-25.
b Part 135, Subpart B - Flight Operations.
Sections 135.77-81.
c. Part 135, Subpart D - VFR/IFR Operating Limitations and Weather Requirements. Section 135.227.
d Part 135, Subpart E Section 135.244.
- Flight Crewmember Requirements.
e. Part 135, Subpart H - Training. Sections 135.323-329,
135.339-347, and 135.351.
f Special Federal Aviation Regulation (SFAR) No. 58, Advanced Qualification Program.
3 RELATED READING MATERIAL.
uieful in developing material, The following material should be instructions, and procedures for incorporation in the certificate holder's training programs and operations manual:
a. AC 20-117, Hazards Following Ground Deicing and Ground Operations in Conditions Conducive to Aircraft Icing.
b l AC 120-58, Pilot Guide for Large Aircraft Ground Deicing.
c. AC 120-60, Ground Deicing and Anti-Icing Program.
d 0 AC 135-17, Pilot Guide for Small Aircraft Ground Deicing.
e. Federal Aviation Administration (FAA) publication, Winter Operations Guidance for Air Carriers and Other Adverse Weather Topics. .
Note: Copies of these documents may be obtained from the Department of Transportation, M-45.3, General Services Section, Washington, DC 20590.
f l Society of Automotive Engineers (SAE):
(1) AMS 1424, Deicing/Anti-Icing Fluid, Aircraft, Newtonian - SAE Type I.
(2) AMS 1428, Fluid, Aircraft Deicing/Anti-Icing, Non- Newtonian, Pseudo-Plastic, SAE Type II.
(3) ARP 4737, Aircraft Deicing/Anti-Icing Methods with Fluids, for Large Transport Aircraft.
Note: Copies of the SAE documents may be obtained by writing to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, Pennsylvania 15096-0001.
57 l International Standards Organization (ISO) publications:
(1) IS0 11075, Aerospace - Aircraft Deicing/Anti-Icing Newtonian Fluids IS0 Type I.
(2) IS0 11076, Aerospace - Aircraft Deicing/Anti-Icing Methods with Fluids.
2 Par 3
(3) IS0 11077, Aerospace - Deicing/Anti-Icing self Propelled vehicles - Functional Requirements.
0 IS0 11078, Aerospace - Aircraft Deicing/ Anti-Icing Non-Newtonian Fluids IS0 Type II.
Note: Copies of the IS0 documents may be obtained from American National Standards Institute, li West 42nd Street, New York, New York, 10036, (212) 642-4900.
4 l BACKGROUND.
a. The "Clean Aircraft" Concept. The current regulations in FAR Parts 121 and 135 rely on the "clean aircraft" concept;
i.e., that no person may takeoff an airplane when frost, ice, or snow is adhering to the wings, control surfaces, or propellers of the airplane (FAR Sections 121.629 and 135.227). The rationale behind this concept is that the presence of even minute amounts of frost, ice, or snow (referred to as "contaminationVV)- on particular airplane surfaces can cause a potentially dangerous degradation of airplane performance and unexpected changes in airplane flight characteristics. Under current regulations, ultimate responsibility for determining whether the airplane is free of contamination and complies with the "clean aircraft" concept rests with the pilot in command (PIC). Both the FAA and industry have developed guidance and recommended procedures that are designed to help the PIC in making that determination. These procedures include monitoring weather conditions and temperature changes, visual checks, and using deicing/anti-icing fluids.
When conditions conducive to the formation of frost, ice, or snow on airplane surfaces exist at the time of takeoff, those surfaces should be checked for contamination in accordance with FAR Section 135.227. .When contaminants are adhering to airplane surfaces, those contaminants, except as .specifically provided for in the rule, should be removed before takeoff. Because of the wide variations in airplane design and performance characteristics, methods for removing contamination for airplanes operated under FAR Parts 121 and 135 vary greatly. Deicing of airplanes may be accomplished:
(1) By applying heated water followed by undiluted glycol-based fluid;
(2) By applying a heated water/glycol solution;
(3) By mechanically brushing the snow or ice off; or
(4) By placing the airplane in a hangar until the frost, ice, or snow melts.
Par 3
Note : Currently, anti-icing (the treatment of the airplane with undiluted (Type II) glycol-based fluid to prevent frost, ice, or snow from adhering to aircraft surfaces) is not commonly used in FAR Part 135 operations.
b Accidents Related to Icing. National Transportation Safety-Board (NTSB) records reveal that 14 ground icing-related accidents and incidents involving airplanes operating under FAR Part 135 occurred during the period of 1984-1992. While most of these accidents/incidents involved FAR Part 135 nonscheduled cargo operations, three involved passenger-carrying operations.
The NTSB identified other probablecauses in some of these accidents/incidents, but in all l4 cases the NTSB identified the existence of frost, ice, or snow'on the wings or other critical surfaces of the airplane as a probable cause. A common thread throughout these accidents/incidents was the pilots' apparent lack of awareness of the potential hazard from even small amounts of frost, ice, or snow on an airplane's wings and control surfaces. For instance, one pilot lost his life in an accident involving a nonscheduled cargo operation in Morrisonville, New York, on March 19, 1984. Prior to the accident, after identifying the presence of ice accumulation on the leading edges and upper wing surfaces, the pilot declined the use of a hangar to warm the airplane and instead attempted to remove the ice from the leading edges by hand. In another accident in Vienna, Missouri, on March 3, 1988, a pilot of a night cargo operation and another person lost their lives after taking off in known icing conditions. Before the flight, a line serviceman noticed ice on the aircraft's wings and suggested its removal, but the pilot declined.
5 DEFINITIONS. The terms used in this AC are not defined in FAR Part 1, but are defined herein for better understanding of this material as follows:
a. Deicing. A procedure by which frost, ice, or snow is removed from the aircraft in order to provide clean surfaces.
b Anti-Icing. A precautionary procedure that provides protection against the formation of frost or ice and accumulation of snow on treated surfaces of the aircraft for a limited period of time.
c. Deicing/Anti-Icing. A combination of the two procedures'above. It can be performed in one or two steps.
(1) One-step deicing/anti-icing is carried out with an anti-icing fluid. The fluid used to deice the aircraft remains on aircraft surfaces to provide limited anti-ice capability.
Par 4
12/12/94 AC “135-16
(2) Two-step deicing/anti-icing consists of two distinct steps. The first step (deicing) is follo.wed by the second step (anti-icing) as a separate fluid application.
Anti-icing fluid is applied to protect the relevant surfaces, thus providing maximum possible anti-ice capability (holdover time).
d anti-icing Holdover Time. The estimated time deicing or fluid will prevent the formation of frost or ice and the accumulation of snow on the treated surfaces of an aircraft.
Holdover.time begins when-the final application of deicing/anti-icing fluid commences, and it expires when the deicing/anti-icing fluid applied to the aircraft loses its effectiveness.
e. Pretakeoff Contamination Check. A pretakeoff contamination check is a check to make sure the wings and control surfaces are free of frost, ice, or snow. FAR Section 135.227 requires that a.pretakeoff contamination check be completed within 5 minutes prior to beginning takeoff. Under FAR Part 135, depending upon the type of aircraft, it may be accomplished from .
within or outside the aircraft and may be visual or tactile or a combination, aslong as.the check is adequate to ensure the absence of contamination. The certificate holder's FAA principal operations inspector ,(POI) should approve the pretakeoff contamination check procedures for each specific type of aircraft operated by the certificate holder. .Also, the pretakeoff contamination check is referenced or described within the certificate holder's operations specifications.
6 OVERVIEW OF THE FAR PART 135 GROUND DEICING RULE. The FAA and the aviation community rely almost exclusively on the PIG's judgment for ensuring the clean aircraft concept.' The FAA believes that pilot education is the paramount element to combatting the threat of icing. After reassessing its policy and reviewing accidentstatistics, the FAA still believes that pilot education is a major ,element in combatting these types of accidents, but it should be supplemented by aircraft checks for contamination. To ensure the implementation of the clean aircraft concept, the FAR Part 135 ground deicing rule requires' education through additional training, and an aircraft check for contamination of the wings and control surfaces prior to beginning takeoff. All FAR Part 135 certificate holders whose pilots expect to takeoff in ground icing conditions should complete a pretakeoff contamination check. The FAR Part 135 ground deicing rule allows an operator to develop an approved alterative method of checking the aircraft for contamination such as use of approved ice detection technology. Additionally, FAR Part 135 certificate holders may comply with FAR Section 121.629(c) deicing program requirements.
Par 5
.
7 0 APPLICABILITY OF THE FAR PART 135 GROUND DEICING RULE. a
a. General. The FAR Part 135 ground deicing rule requires that deicing/anti-icing pilot training and pretakeoff ' contamination check procedures or an approved alternative to the pretakeoff contamination check (alternative aircraft check) be incorporated into a certificate holder's approved training program. The procedures for a pretakeoff contamination check or the alternative aircraft check should;also be in the certificate holders operations manual and referenced in its operations specifications. Pretakeoff contamination check or alternative aircraft check procedures will be fully described inthe operations specifications for those operators not required to have an operations manual. The FAR Part.135 ground deicing rule does not apply to FAR Part91 operations conducted by a FAR ' Part 135 operator.
b FAR Part 135 Certificate Holder Who Complies with the, FAR Part.121 Ground Deicing Rule. If approved, an FAR Part 135 operator can comply with the FAR Part 121,ground deicing rule.
However, the operator must comply'with all the provisions of FAR Section 121.629(c), including training requirements and not just with selected provisions.
c. CertificatebHolders Who Use Only One Pilot in Their Operations. Certificate holders who use only one pilot in their operations (single pilot operations)'are not-required to comply .with the manual and approved training program requirements in FAR Sections 135.21,. Manual'Requirements, and 135.341, Pilot and Flight Attendant Crewmember Training Programs. Therefore, single pilot operations are not required to have an approved pilot training program nor the additional training required by the FAR Part 135 ground deicing rule. However, single pilot operations must comply with,all the operational requirements (i.e., pretakeoff contamination check or an approved alternative to the pretakeoff contamination check described in its operations specifications) of the FARPart 135 ground deicing rule. The pilots of these types of operations will need to demonstrate the' knowledge required to operate in ground icing conditions during initial and recurrent flight checks. Thus, the information contained in this 'AC is also applicable to certificate holders who use only one pilot in their operations.
d. Helicopter Operations.
operate in icing conditions. Helicopters generally do not The FAA's review of icing-related accidents and incidents did not reveal any accident history for helicopter operations that suggest additional training or a special inspection requirement would be necessary. Therefore, helicopter operations conducted under FAR Part 135 are excluded -6 Par 7
from the additional training and aircraft checking requirements of the FAR Part 135 ground deicing rule. However, the I'clean aircraft" concept still applies to helicopters.
e. Certificate Holders In Areas Of Operations Where Ground Icing Conditions Are Not Likely'To Be Encountered. Each certificate holder may elect not to fly during grourid icing conditions. Ground icingconditions are defined as anytime conditions are such that frost, ice, ‘or snow may reasonably be expected to adhere to the airplane. The prohibition against takeoffs in ground icing conditions will be specifically stated in the certificate holder's operations specifications.
8 l MISCELLANEOUS.
a. Associated Deicing/Anti-Icing Personnel (To Include Contractors). The ground deicing rule in FAR Part 135 requires additional training for pilots only. However, if the certificate holder uses additional employees (i.e.,, maintenance mechanic, ramp agent, service personnel, and contractors) to accomplish deicing and anti-icing procedures, the certificate holder's manuals will contain procedures for those personnel consistent with FAR Sections 135.21 and 135.23.
9 RULE OPERATIONAL REQUIREMENT OF THE FAR PART 135 GROUND DEICING 0
a. Pretakeoff Contamination Check. Except for those FAR Part 135 certificate holders who voluntarily choose to comply with the FAR Part 121 ground deicing rule or those that develop an approved alternative procedure, each applicable air carrier who operates under FAR Part 135 should develop approved procedures for a pretakeoff contamination check of the aircraft.
As previously stated, the FAR Part 135 ground deice rule does not apply to a certificate holder who does not operate in ground icing conditions. In accordance with FAR Section 135.227, the certificate holder's PO1 should approve the pretakeoff contamination check procedures for each specific type of aircraft operated by the certificate holder. Except for single pilot operations, the procedures for a pretakeoff contamination check should be contained in the certificate hol,der's approved training program, operations manual, and referenced within the certificate holder's operations specifications. FAR Part'135 single pilot operations will have the pretakeoff contaminati0.n procedures described in its operations specifications.
b . Alternative Procedure to the Pretakeoff Contamination Check:
altern surfac at es The Administrator may approve a certificate holder's ive procedure which ensures .that wings and control are free of frost, ice, or snow, instead of the Par 7
pretakeoff contamination check as set forth in this rule. An alternative procedure may include procedures, techniques, or equipment (such as wing icing sensors) to establish that wings and control surfaces are not contaminated. Pretakeoff contamination check or alternative aircraft check procedures will be fully described in the operations specifications for those operators not required to have an operations manual. The FAR Part 135 ground deicing rule does not apply to FAR Part 91 operations conducted by an FAR Part 135 operator.
FAR deic Sect deve
c. FAR Part 135 Certificate Holder Who Complies with Part 121 Ground Deicing Rule: The FAR Part 135 ground ing rule allows a certificate holder to comply with FAR ion 121.629(c) program requirements. Guidance for lopment of an FAR Part 121 program is contained in AC 12 10 TRAINING REQUIREMENTS IN CERTIFICATE HOLDER'S APPROVED TRAINING PROGRAM. For certificate holders who are required the O-60.
to have an approved training program and who anticipate takeoffs in ground icing conditions, that training program should include pilot ground training in those subjects relating to deicing and anti-icing operations as required by FAR Section 135.345 for initial, transition, and upgrade training and FAR Section 135.351 for recurrent training. The training required by the regulation include procedures for operating airplanes.during ground icing conditions. That training should include at least the following elements if applicable to the type of aircraft and methods of deicing/anti-icing used.
a. The use of holdover timetables when using deicing/ anti-icing fluids.
b Aircraft deicing/anti-icing procedures, including inspection and check procedures and responsibilities.
c. Communications procedures.
d Airplane surface contamination (i.e., adherence of frost,"snow, ice, or snow) and critical area identification, and how contamination adversely affects airplane performance and flight characteristics.
e. Types and characteristics of deicing/anti-icing fluids, if used by the certificate holder.
f l Cold weather preflight inspection procedures.
g Techniques for recognizing contamination on the airplane.
Par 9
11 USE OF HOLDOVER TIMETABLES WHEN USING DEICING/ANTI-ICING FL&D%
a. Use of Holdover Timetables. Holdover times are only an estimate of the time deicing/anti-icing fluid prevents the formation of frost or ice and the accumulation of snow on the treated surfaces of an aircraft. A holdover time begins when the final application of deicing/anti-icing fluid commences and expires when the deicing/anti-icing fluid applied to the aircraft loses its effectiveness as described in the appropriate holdover timetable. The effectiveness of deicing/anti-icing fluids are based on a number of variables; e.g., temperature, moisture content of the precipitation, wind, or aircraft skin temperature.
The operational use of holdover timetables is not mandatory for 'FAR Part 135 operations unless the operator elects to comply and the FAA approves its compliance with the FAR P'art 121 ground deicing/anti-icing rule requirements. Holdover timetables provide information on the effectiveness of deicing/anti-icing fluids and should be used for departure'planning and coordination -purposes in conjunction with pretakeoff contamination check procedures. Operations manuals and operations specifications should contain detailed procedures for conducting the pretakeoff contamination check as well as the procedures for using the holdover timetables.
b timet&les Development of Holdover Timetables. Holdover have been developed by SAE and ISO. Each certificate holder may develop their own holdover timetables for use by its personnel, but the timetables should be supported by data acceptable to the Administrator; currently, the SAE/ISO holdover timetables are considered by the FAA to be the,only acceptable data for use by FAR Part 121 certificate holders. This policy will also apply to FAR Part 135 certificate holders (see Appendix A, Tables 1 and 2). Further guidance regarding holdover timetables is contained in AC 200ll-7, AC 120-58, AC 135-17, SAE ARP 4737, and IS0 11076.
12 AIRCRAFT DEICING/ANTI-ICING PROCEDURES, INCLUDING INSPECTION AND CHECK PROCEDURES AND RESPONSIBILITIES. Deicing and anti-icing procedures should be specific to each aircraft type in accordance with FAR Section 135.345. Those aircraft-specific procedures should include instructions and checking guidelines for use by their'pilots, and if appropriate and authorized, other personnel to determine whether or not aircraft surfaces are free of contaminants. Those aircraft-specific instructions and guidelines should also be in the certificate holder's operations manual, and‘described or referenced in their operations specifications.
Par 11 9
a. Deicing/Anti-Icing Procedures. Deicing/anti-icing procedures should include; as applicable to each certificate holder:
(1) fluid).
Methods of deicing (e.g., warm hangar, deicing
(2)
(3)
(4)
(5)
(6) Aircraft-specific considerations.
Location-specific procedures.
Post deicing/anti-icing checks.
Contractor Deicing,. Many certificate holders will utilize contract services, such as aircraft servicing vendors, fixed base operators, or other air carriers to perform deicing/anti-icing. If such is the case, the certificate holder's training program should include training for contractors and/or'the PIG's responsibilities for supervising a contractor who provides deicing/anti-icing services.
Safety requirements during fluid application.
b Deicing/Anti-Icing Checking Procedures and Responsibilities. The certificate holder's training program should have pilot training on aircraft-specific surface contamination checking to include the following:
(1) Pilot Preflight Inspection/Cold Weather Preflight Inspection Procedures. This is the normal walkaround preflight inspection conducted by a pilot. This inspection should be used to note any aircraft surface contamination and to direct any required deicing/anti-icing operation.
(2) Pretakeoff Contamination Check. An aircraft check completed within 5 minutes prior to beginning takeoff to make sure the wings and control surfaces are free of contamination.
Each carrier should define the content of the pretakeoff contamination check. The check may be conducted from inside or outside the aircraft, depending upon such factors as atmospheric conditions, lighting conditions., aircraft type and ability of the crew to see the relevant aircraft surfaces.
(3) Certificate holders should consider the following guidelines for obtaining approval to conduct thb pretakeoff contamination checks from inside the aircraft.
(i) Can enough of the surfaces be seen to adequately determine whether or not the wings and control surfaces are free of contaminants? This determination should consider the aircraft type; the method of conducting the 10 Par 12
check--that is, from the cockpit or cabin; lighting; and atmospheric conditions.
(ii) Does the certificate holder have procedures to. recognize, and has the pilot been properly trained to recognize changes in weather conditions to allow the PIC to ascertain whether or not the wings and control surfaces could reasonably be expected to remain free of contaminates?
CL Alternative Procedure. The Administrator may approve a certificate holder's alternative procedure, which ensures that wings and control surfaces. afe free of frost, ice, or snow, G instead of a pretakeoff contamination check. An alternative procedure may include procedures, techniques, or equipment (such as wing icing sensors) to establish that wings and control surfaces are not contaminated. Any alternative procedure should be approved by the certificate holder's PO1 through the Manager, Air Transportation Division, AFS-200, and after approval, detailed in the operator's training program (if applicable), operations manual (if applicable), and described or referenced in its operations specifications.
d procedures PIC Responsibility. Operator-developed guidance and should contain a discussion regarding the PIG's responsibility to make the decision on whether or not to take off.
e. Aircraft Surfaces. The aircraft surfaces, which should be clear of contaminants before takeoff, should be described in the aircraft manufacturer% maintenance manual or other * manufacturer-developed documents, such .as service or operations bulletins.
(1) For each type of aircraft used in their operations, certificate holders should explain in their training‘ programs and list in their operations manual those surfaces which should be checked during preflight inspections and pretakeoff contamination checks. -
(2) Generally, the following aircraft surfaces should be clear of contaminants, if the aircraft manufacturer's information is not available:
I
(1) Propeller, windshield, wing, empennage, stabilizing, and control' surfaces.
(ii) Powerplant installation(s), including associated surfaces and systems such as engine inlets and fuel ~. vents.
Par 12 11
(iii) Airspeed, altimeter, rate of climb, and flight attitude instrument, including associated surfaces or systems such as pitot heads/static ports, and instrument sensor pickup points.
13 0 COMMUNICATIONS.
a. Before beginning the. deicing/anti-icing procedures, the PIG should:
(1) Coordinate with air traffic control (ATC) for departure planning.
(2) Obtain the most current weather information.
b When deicing/anti-icing with fluids is accomplished, the PIG should have the following information:
(1) Fluid type (for example, Type I or Type II).
(2) Fluid/water mix ratio. .
(3) Start time of final fluid application/beginning of holdover time.
(4) Verification that the aircraft is free of , contamination.
14 l AIRPLANE SURFACE CONTAMINATION.
a. Certificate holders should include training which ensures that pilots are knowledgeable in the following:
(1) Freezing Precipitation. Snow, sleet, freezing rain, drizzle, or hail which adheres to aircraft surfaces.
(2) Frost, Including Hoarfrost. Hoarfrost is a deposit of interlocking ice crystals formed by direct sublimation of water vapor on an object or aircraft surface, which is at or below 0" C (32°F).
(3) Freezing Fog. Clouds of supercooled water droplets that form a deposit of ice on objects in cold weather conditions.
(4) Snow. Precipitation in the form of small ice crystals or flakes which may accumulate on or adhere to aircraft surfaces.
12. Par 12