d. The following information is requested for tests to be witnessed by FAA personnel or its representatives:
(1) Identification and location(s) of unit(s) where conformity inspection(s) and test(s) are to be conducted.
(2) Name and telephone number of project engineer at the above location(s).
(3) Approximate date(s) that the unit(s) will be available for inspection.
e. FAA or appointed designee should inspect the cart, waste container, or waste compartment for conformity prior to the test.
f. The following suggested materials may be used for this test:
(1) Material to be ignited in the waste compartment, waste container, or waste cart should consist of the following typical mixture of crumpled combustibles:
(i) Eight paper hand towels-two ply, approximately l0 x 11-inches (40 percent by number).
(ii) Five paper napkins-two ply, approximately 16 x 16-inches (25 percent by number).
(iii) Four paper hot drink cups-8 ounce size (20 percent by number).
(iv) Two paper cold drink cups-3 ounce size (l0 percent by number).
(v) One empty cigarette package (5 percent by number).
The total amount of combustible material in the above proportions should be sufficient to fill the waste container, compartment, or cart to 3/4 full. Any changes to this mixture should be approved by the FAA.
(2) Combustible materials used for meal cart tests should be representative of those regularly used. If the airline for which the cart is intended uses noncombustible dishes, the test should be conducted with combustible dishes. The airline may change or the cart may be used by another airline which uses combustible dishes. Normally this will include:
(i) One cup.
(ii) One salad dish.
(iii) One salad dressing container.
(iv) One entree dish.
(v) One dessert dish.
(vi) Three eating utensils (i.e., knife, fork, spoon).
(vii) One crumpled paper napkin-two ply, approximately l6 x l6-inches.
The total amount of trays, each containing the materials in the above proportions, shall be sufficient to fill the cart. Remove the tray above the one to be ignited to give the fire some air.
Ignite the materials on the second or third tray up from the bottom. Entree or heated carts, if they contained ignition sources, should be tested by igniting an entree dish (the second or third one up from the bottom) or equivalent filled l/2 full of alcohol to simulate a grease fire and remove the tray above the one that is to be ignited. If the entree cart is used as a serving cart or for storage of used materials, the procedures used for standard cart tests should also be followed.
(3) A thermocouple and readout system capable of continuously recording the temperature within the item being tested may be used.
4. TEST PROCEDURES.
4.l WASTE COMPARTMENT AND WASTE CONTAINER.
a. All waste compartments with nonmetallic waste containers should be tested with the containers installed (4.1c and 4.1e through 4.1h) and also with the container removed (4.1d through 4.1h). Alternatively, it may be analyzed which condition (with or without the container) is more critical and only that condition need be tested. Waste compartments with metal waste containers should be tested without the container (4.1d through 4.1h).
b. If the compartment is not tested with the container removed, the outside of the compartment must be conspicuously placarded to require the container be in place.
c. Install the waste container loosely filled with material per 3.f.(1) and close all doors.
Proceed with 4.1e through 4.1h.
d. Loosely fill the waste compartment, without the waste container, with material per 3.f.(1) and close all compartment doors.
e. If a thermocouple is used, install it through the waste compartment lid or other suitable opening such that the thermocouple bead is located l.5 to 2.0-inches above the surface of the waste material.
f. Ignite the waste material in the container or compartment by inserting a crumpled lighted paper towel through the waste compartment lid or chute. Ensure development of an adequate fire by allowing approximately 50 percent of the waste material surface area to ignite prior to closing the lid. It is best to light the back surface first and work forward. The flame coverage is deceiving; be absolutely confident at least 50 percent of the surface is ignited.
g. The temperature indicated by the thermocouple will increase after ignition and then start to drop as the flame subsides. When the thermocouple indicates a temperature below l50°F., or does not reignite when the door is opened, the test is complete. Open the compartment door, remove the waste container if used, and inspect the container, cart, and/or compartment for damage.
h. It is recommended that the applicant takes photographs prior to and after test, records thermocouple temperatures, if used, and record all observations during the test. The photographs, temperatures, and observations should be included in the test report.
4.2 CARTS.
a. All tests are to be conducted in an open area equivalent to an aircraft cabin environment or connected to the conditioned air ducts in the galley unit (Refer to 4.2g).
b. Load carts with materials as listed in 3.f.(1) for waste carts and 3.f.(2) for meal, entree (heated) or air chilled carts.
c. If used, install the thermocouple through the waste access door or other suitable opening such that the thermocouple bead is located l.5 to 2.0-inches above the surface of the top tray.
d. Meal Carts. For meal cart tests, ignite two crumpled paper napkins and place adjacent to other combustible items on the lower tray. Remove the tray above for the test. Allow a good flame front to develop by allowing approximately 50 percent of the surface area of the napkin to ignite. Insert tray and close all cart doors.
e. Waste Carts. For waste carts, use the procedure called out in Section 4.l.
f. Entree (Heated) Carts. For entree or heated carts, ignite a pan of alcohol the size of an entree dish, and insert into the cart on the lower shelf (Refer to 3.f.(2)). Remove the tray above for the test.
g. Air-Chilled Carts.
(1) The air chilled carts should have all openings, gaskets, seals, and connectors representative of the production carts installed or simulated.
(2) Air chilled carts should be loaded with the items as listed in 3.f.(2).
(3) Air chilled carts should be tested under two conditions as follows:
(i) Stowed within galley.
809 (A) If used, install the thermocouple through the access door or other suitable opening such that the thermocouple lead is located l.5 to 2.0-inches above the surface of the top tray.
(B) Ignite two crumpled paper napkins and place adjacent to the other combustible items on the lower tray. Remove the tray above for the test. Allow a good flame front to develop by allowing approximately 50 percent of the surface area of the napkin to ignite.
Insert the tray and close all cart doors.
(C) Place the cart into the galley structure so that it is connected or attached to the chilled air distribution ducts with the designed airflow volume. Circulate air through the cart at the designated airflow rate.
(ii) Unstowed Carts.
(A) Remove the cart from the chilled air distribution duct.
(B) Use the procedure listed in items 4.2g.(3)(i)(A) and 4.2g.(3)(i)(B).
h. The temperature indicated by the thermocouple will increase after ignition and then start to drop as the flame subsides. When the thermocouple indicates a temperature below 150 °F, or does not reignite when the door is opened, the test is complete. Open the compartment door, remove the waste container if used, and inspect the container, cart, and/or compartment for damage.
i. Take photographs prior to and after testing, record thermocouple temperatures, if used, and record all observations during the test. The photographs, temperatures, and observations should be included in the test report.
5. ACCEPTANCE CRITERIA.
a. Compliance with the fire containment requirements of § 25.853 requires that the waste compartment/container or cart, as applicable, "must be at least fire resistant" (meet the 45 degree burn test contained in paragraph 621.b(2) of this AC or, alternatively as later promulgated by Amendment 25-32 in § 25.855(a-1)) and be able to contain the fires described in Section 4.
b. Damage to the waste compartment/container is acceptable provided the waste compartment does not burn through or ignite surrounding materials or no flame issues from waste compartment or cart.
c. Damage to carts and contents are acceptable provided the container portion of the cart does not burn through.
6. FIRE CONTAINMENT BY SIMILARITY REPORT. A unit that is similar in construction, materials, and volume to a unit previously approved by the FAA may be approved without a fire containment test, with a similarity report that satisfactorily demonstrates the similarity.
6.1 PURPOSE. The similarity report should state the purpose, which is to show by similarity to previously approved units, that waste containers, waste compartments, and carts containing combustible materials contain a fire in compliance with this document and the fire containment requirements of § 25.853. The report should also include:
a. Identification by part and drawing number of items to be approved by similarity to previously approved items.
b. Identification of airplane(s) in which the item will be installed as well as the airplane and airline customer for which the original test was conducted. A copy of the original test report should also be attached or referenced.
c. Identify the fire containment requirements of § 25.853 for which compliance will be demonstrated by similarity.
6.2 DESCRIPTION OF SIMILARITY SPECIMEN. Drawing numbers, photographs, etc., for items to be approved by similarity, and previously approved unit to which they are being compared should be provided.
6.3 SIMILARITY REQUIREMENTS.
a. Configuration should be adequately defined by production drawings or equivalent sketches and layouts.
b. Construction or fabrication of the subject unit should be similar to previously approved unit as shown by drawing or sketches with part numbers.
c. Ventilation or air leakage paths (length or area) should be equal to or less than previously approved unit. Air gap dimensions between waste compartment access or chute doors and sill should be shown on sketches or drawings.
d. Compartment volume should be equal to or less than previously approved unit, and tabulated for both units. Include dimensions and volume comparisons of the unit tested and of the unit to be approved by similarity.
e. A statement should be made in the report verifying that the design permits no waste material to fall out of the stowage or waste compartments as installed in the airplane.
6.4 CONCLUSION.
a. A statement should be made in the report verifying that the design confines a fire within the waste compartment and does not present a hazard to personnel or other compartments.
b. A statement should be made in the report that the galley or lavatory waste container and compartments are qualified to the fire containment requirements of § 25.853 based on the attached comparison analysis that shows these units to have equivalent fire containment capabilities of the previously approved test unit documented in the referenced report.
7. PARAGRAPH (e) and (f). Refer to AC 20-42C, dated 3/7/84, “Hand Fire Extinguishers for Use in Aircraft,” for guidance on acceptable fire extinguishers.
THIS PAGE INTENTIONALLY LEFT BLANK
813 APPENDIX 9
ACRONYMS AC Aircraft Certification AC Advisory Circular ACO Aircraft Certification Office AFM Airplane Flight Manual ASTM American Society of Testing and Materials AWG American Gage Size Conductor BTU British Thermal Unit CFR Code of Federal Regulations ELT Emergency Locator Transmitter FAA Federal Aviation Administration FSSR Flight Standards Service Releases
g. G ravity GPH Gallons Per Hour Hg Mercury HIC Head Injury Criterion NACA National Advisory Committee for Aeronautics NASA National Aeronautics and Space Administration PSI Pounds per Square- inch RTO Rejected Takeoff SAE Society of Automotive Engineers SRP Seat Reference Point STC Supplemental Type Certificate TSO Technical Standard Order TT & L Taxi, Takeoff, and Landing
THIS PAGE INTENTIONALLY LEFT BLANK
815 APPENDIX 10 CROSS REFERENCE FOR PRE-AMENDMENT 25-72 AND POST AMENDMENT 25-72
RELOCATION AND REWORDING OF PERTINENT CRASHWORTHINESS SECTIONS BY AMENDMENT 25-72 NOTE: Only those sections, paragraphs or sub-paragraphs that have been relocated are listed here. If the section, paragraph or sub-paragraph is exactly the same between pre and post amendment 25-72, that section, paragraph or sub-paragraph will not appear in the list below. Minor rewording or revisions will also be listed below.
Pre-amendment 25-72 Post-Amendment 25-72
(b) rewritten (content the same)
25.783(g) minor revision (correct previous error)
25.785(a), relocated from § 25.1307(a), Refer to below
25.785(a) (b)
(b) (c)
(c) (d)
(d) (j)
(e) (k)
(f) (e)
(c) rewritten and part moved to (h)(1), part moved to (h)(6)
(h)(1) (h)(2)
(h)(2)(i) (h)(5)
(h)(2)(ii) (h)(3)
(i) (f) & (f) (1)
(i)(1) (f)(1)
(i)(2) (f)(2)
(i)(3) (f)(3)
(j) (h)(4)
25.785(k) (l)
25.791 separated into 25.791(a) and (b)
25.801(a) revised reference from § 25.807(d) to 25.807(f)
25.803(a) minor rewording
(a) 25.807(d)(6)(ii) and (iii)
(b) minor rewording, added content of 25.803(d), Refer to below
(c)(1) Appendix. J (a)
(c)(2) “ (b)
(c)(3) “ (c)
(c)(4) “ (d)
(c)(5) “ (e)
(c)(6) “ (f) Pre-amendment 25-72 Post-Amendment 25-72
25.803(c)(7) Appendix J (g) with minor rewording
(c)(8) “ (h)
(c)(9) “ (i)
(c)(10) “ (j)
(c)(11) “ (k)
(c)(12) deleted, already in Appendix J, (g)
(c)(13) Appendix J (l)
(c)(14) “ (m)
(c)(15) “ (n)
(c)(16) “ (o)
(c)(17) “ (p)
(c)(18) “ (q)
(c)(19) “ (r)
(c)(20) “ (s)
25.803(d) added to 25.803(c)
25.803(d) is reserved in Amendment 25-72
25.803(e) 25.810(c)
25.803(e) is reserved in Amendment 25-72
25.805 25.807(f) with minor rewording
25.807(a),(a)(1),(a)(2),(a)(3),(a)(4) minor rewording
(a)(7),(a)(7)(i),(a)(7)(ii) (a)(7) with minor rewording
(a)(7)(iii),(a)(7)(iv),(a)(7)(v) 25.813(a)
(a)(7)(vi) 25.785(h)(1)
(a)(7)(vii) 25.813(b),(b)(1),(b)(2)
(a)(7)(viii) 25.810(a),(a)(1)
(a)(7)(ix) 25.810(b) and 25.807(b)
(b) 25.813 and 25.807(c)
(b)(1),(b)(2) 25.807(c)
(c) 25.813 with minor rewording
(c)(1),(c)(2) 25.807(d),(d)(1)
(c)(3) (d)(2)
(c)(4) (d)(3)
(c)(5) (d)(4)
(c)(6) (d)(6)(i)
(c)(7) (d)(7)
(d) (e) with minor rewording
817 Pre-amendment 25-72 Post-Amendment 25-72
25.809(d) 25.809(f)
(e) (g)
(f) 25.810(a)
(g) 25.809(e)
(h) 25.810(d) with minor rewording
(i) 25.809(d)
(j) (h)
25.813(a) revised with additional wording
(b) (b),(b)(1),(b)(2)
25.851(a)(1) 25.851(a)(4)
(a)(2) (a)(5)
(a)(3) (a)(6)
(a)(4) (a)(3)
(a)(5) (a)(1) with minor rewording
(a)(6) (a)(2)
(b),(b)(1) minor rewording
25.853 minor rewording
(d) Appendix F, Part I, (a)(1)(i), with minor rewording (a-1) 25.853©
(b) Appendix F, Part I, (a)(1)(ii), with minor rewording (b-1) Appendix F, Part I, (a)(1)(iii), with minor rewording (b-2) Appendix F, Part I, (a)(1)(iv), with minor rewording (b-3) Appendix F, Part I, (a)(1)(v), with minor rewording
(c) 25.853(b)
(d) part (placard requirement) moved to 25.791(a)
(d)(1) 25.853(d)
(d)(2) 25.791(a)
(e) 25.853(f) plus part (placard requirement) moved to 25.791(c)
(f)* 25.853(e) plus part (placard requirement) moved to
25.791(d) and 25.791(e)* NOTE: * last sentence on lettering size and color has been dropped.
25.855(a) 25.855(d) and Appendix F, Part I (a)(2)(i) with liner requirements moving to 25.855(b) and (c)