Page C - 20
(v) The analysis must include appropri ate special factors, casting factors, bearing factors, and fitting factors prescribed by §§ 27.619, 27.621, 27.623, and 27.625, respectively. The fitting factor of 1.15 must be applied in the analysis of the tail rotor installation.
AC 27.401A. § 27.401 (Amendment 27-27) AUXILIARY ROTOR ASSEMBLIES.
a. Explanation . Amendment 27-27 removed this section since the requirements are adequately addressed in §§ 27.337, 27.339, and 27.341.
b. Procedures . The policy material pertaining to this section is retained as supplemental information.
AC 27.403. § 27.403 AUXILIARY ROTOR ATTACHMENT STRUCTURE.
a. Explanation .
(1) The auxiliary rotor attachment stru cture(s), which is considered to include gearboxes, must be designed to withstand design limit loads that occur in flight and on landing. These design loads that generally consist of the following must be established for the particular flight and landing condition under consideration.
(i) Inertia loads generated by li near and angular accelerations of the auxiliary rotors and their gearboxes, combined with--
(ii) Thrust and torque loads developed by the auxiliary rotors.
The linear and angular acceleration loads imposed by the weight of the tail rotor and gearbox are generally derived from airframe loads data. Thrust and torque output of the tail rotor are derived during external aerodynamic and landing loads development for pertinent flight and landing conditions.
(2) General rules related to proof of structure loads and factor of safety are §§ 27.307, 27.301, 27.303, and 27.305.
b. Procedures .
(1) The angular and linear accelerati on loads combined with appropriate tail rotor thrust and torque for the critical conditions shall be imposed on the tail rotor gearbox mount lugs, the airframe mounting structure, and the attaching hardware.
(2) The yaw and maximum power clim b conditions are generally critical.
Landing and maneuvering conditions with and without power may also impose high inertia and rotor thrust and torque loads on the attachment structure.
Page C - 21
(3) The derivation of the loads and conditi ons is too extensive to include here.
Additional information can be found in the U.S. Army Material Command Report AMCP 706-201, “Engineering Design Handbook: Helicopter Engineering, Part One, Preliminary Design.”
AC 27.403A. § 27.403 (Amendment 27- 27) AUXILIARY ROTOR ATTACHMENT STRUCTURE .
a. Explanation . Amendment 27-27 removed this section since the requirements are adequately addressed in §§ 27.337, 27.339, 27.341.
b. Procedures . The policy material pertaining to this section is retained as supplemental information.
AC 27.411. § 27.411 GROUND CLEA RANCE: TAIL ROTOR GUARD.
a. Explanation .
(1) The rule requires specific protecti on to prevent the tail rotor from contacting the landing surface during a normal landing if it is possible that the tail rotor will contact the surface. The rule states that it must be impossible for the tail rotor to contact the surface during a normal landing.
(2) If a guard is requir ed, the guard and its supporting structure must withstand suitable design loads.
(3) Section 27.501(c)(1) contains skid landing gear drag requirements that may be applied to the guard design loads.
b. Procedures .
(1) The applicant may submit sketc hes or drawings showing probable clearance with typical level landing surfaces during normal landings. Typical attitudes such as nose-high autorotation, or autorotation with power-on landing, or other possible tail-low attitudes should be investigated. If the drawings or sketches reveal that it is not likely the tail rotor will contact the landing surface, this minimum clearance with the landing surface may be confirmed during official FAA/AUTHORITY flight tests, such as HV and landing tests. The clearance may be confirmed by having a frangible device of suitable length (i.e., a balsa wood dowel) extending beyond the guard and attached to the tail rotor guard or other appropriate fuselage part. If the device is not damaged, broken, or no contact is made with the surface, compliance has been demonstrated.
(2) If it is possible for the tail rotor guard to contact the landing surface, suitable design loads must be established for the guard. ANC-2a dated March 1948, “ANC Bulletin Ground Loads,” paragraph 6.4, entitled “Tail Bumper Criteria,” is an acceptable
Page C - 22 means of deriving the rotorcraft kinetic energy that shall be absorbed by the guard. This method is noted here for convenience.
(i) The tail rotor guard shall be able to absorb the kinetic energy of the rotorcraft in its most unfavorable CG position in the tail-down landing attitude. The kinetic energy that the tail rotor guard should be capable of absorbing may be determined by the following:
W V S2 KY2 KE = X 2g (KY2 + 1B2)
where-- V S = vertical speed ft/sec, derived from § 27.725(a) K Y = pitching radius of gyration - ft from pitching axis 1 B = distance from most critical CG location to the guard or bumper contact point - ft W = gross weight less rotor lift from § 27.473(a) - lbs g = 32.2 ft/sec 2
(ii) Other, more recent, analytic al techniques (most utilizing computer programs) may, of course, be used rather than the ANC-2a means after proper substantiation for applicability and validity.
(iii) The tail rotor guard should not fail when the limit and ultimate load, which is derived from a combination of the limit kinetic energy and the guard resulting limit deflection required to dissipate the energy, is imposed on the guard and the rotorcraft tail (see § 27.305).
(3) Substantiation of the guard, skid, or bumper for the design loads derived may be accomplished by test or analysis as stated in § 27.307(a).
(4) Several rotorcraft tail rotor guards are installed solely for the protection of ground personnel from the rotating tail rotor. For guards installed for this purpose, the applicant should use prudent and reasonable design loads and features. Such guards should not present a hazard to the rotorcraft because of its design features.
AC 27.413. § 27.413 STABILI ZING AND CONTROL SURFACES.
a. Explanation . Minimum design loads are specified for stabilizing as well as control surfaces.
(1) Paragraph (a) of the rule require s application of minimum empirical design loads, application of critical maneuvering loads, and application of critical maneuvering loads combined with vertical gust loads (30 feet per second or 17.8 knots per § 27.341).
Page C - 23
(2) Paragraph (b) requires load distribu tions that closely simulate actual pressure distributions. Both spanwise and chordwise distributions are intended.
(3) These surfaces are used for st ability and control thereby hopefully extending the CG range and increasing the airspeed of modern designs.
(4) To “closely simulate actual pressure condition” on the surfaces, unsymmetrical loads are also required on horizontal surfaces. An arbitrary distribution, if conservative, may be used.
(5) It is noted § 27.571 requires fatigue s ubstantiation of the flight structure which will include control and stabilizing surfaces.
(6) If the surface is controllable, a proof and operation test of the surface control system is required by §§ 27.681 and 27.683.
b. Procedures . Modern rotorcraft designs have generally employed a fixed or a wholly movable, not split or divided, stabilizing or control surface.
(1) Design Loads.
(i) Limit loads of 15 pounds per square foot will apply up to approximately a 90-knot design airspeed. Above a 90-knot design airspeed (1.11VNE), the coefficient (CN = 0.55) imposes higher limit loads on the surface. The coefficient CN is assumed normal to the chordline of the section.
(ii) In addition, combined maneuver ing and vertical up or down gust loads may impose the highest limit loads on the control surfaces of rotorcraft. This is attributed to the change in angle of attack and change in resultant airspeed.
(iii) The applicant may choose to derive the limit loads using maximum aerodynamic coefficients for the surface under consideration at the maximum design airspeed combined with a 17.8-knot gust. This would be acceptable provided these design loads exceed the minimum loads derived from a CN = 0.55 at design airspeed or exceed 15 pounds per square foot load on the surface.
(2) The load distribution on the surface should closely simulate actual pressure distributions.
(i) The spanwise load may be rectangular, or other acceptable conservative distributions may be used. The method developed by O. Schrenk in NACA TM 948, 1940, is an acceptable method for approximation of spanwise distribution.
Page C - 24 NOTE: The method is valid for aspect ra tios of 5 through 12 and for rectangular planforms such as used on rotorcraft, other planforms may be acceptable as prescribed in the TM.
(ii) The chordwise distribution appr opriate for the aerodynamic shape or a conservative distribution should be used.
(iii) The flight load survey conducted under § 27.571 may be used to confirm design parameters and possible load distribution data. On controllable surfaces, the pitching moment (control loads) may be measured for fatigue substantiation of the control system. The control stabilizing surfaces may be subject to loads measurement and possible fatigue tests for fatigue substantiation also.
(3) Proof of the struct ure for the required loads is specified in §§ 27.301,
27.303, 27.305, and 27.307. Tests or analysis may be used as prescribed. If analysis is used, fitting factors and other appropriate factors prescribed by the rules of §§ 27.625, 27.621, and 27.623 will be required in the analysis.
AC 27.413A. § 27.413 (Amendment 27-27) STABILIZING AND CONTROL SURFACES .
a. Explanation . Amendment 27-27 removed this section since the requirements are adequately addressed in §§ 27.337, 27.339, and 27.341.
b. Procedures . The policy material pertaining to this section is retained as supplemental information especially as reference material for paragraph AC 27.341 (§ 27.341).
AC 27.427. § 27.427 (Amendment 27-27) UNSYMMETRICAL LOADS.
a. Explanation . Amendment 27-26 added the standard and Amendment 27-27 amended it. Minimum unsymmetrical design loads are specified for horizontal tail surfaces and also vertical tail surfaces whenever they support the horizontal tail surfaces.
(1) Loads are derived by rational analysis, or for earlier certification bases, the prescribed empirical loads of § 27.413 may be used. Section 27.413 was removed by Amendment 27-27 since the requirements are adequately addressed in §§ 27.337,
27.339, and 27.341.
(2) Rational loads, appropriate for the aerodynamic surfaces, should be distributed according to the standard.
(3) When vertical tail surfaces support the horizontal tail surfaces, the vertical tail surfaces and supporting surfaces are required to support the critical combination of vertical and horizontal surface loads.
Page C - 25
b. Procedures . Two basic loading conditions are required by § 27.427 for each of the two basic empennage configurations.
(1) Horizontal surfaces suppor ted by the tail boom or fuselage. Structural substantiation should be provided for all six combinations shown in figure AC 27.427-1.
All of these empirical loading distributions should be used unless rational analysis shows one or more of each set of conditions to be non-critical or equal or more realistic distributions are substantiated. Rectangular spanwise air load distribution should be used unless more rational distribution is substantiated. If end plates are used, the air loads should be distributed accordingly.
(i) First unsymmetric al loading condition:
(A) 100 percent of the flight load is applied to one side of the plane of symmetry; and 0 percent of the flight load is applied to the other side of the plane of symmetry.
(B) For surfaces with end plates or other similar devices, the load distribution will be changed accordingly.
(ii) Second unsymmetr ical loading condition:
50 percent of the flight load is applied to one side of the plane of symmetry acting up;
and 50 percent of the flight load is applied to the other side of the plane of symmetry acting down.
(2) Horizontal surfaces s upported by a vertical surface. Structural substantiation should be provided for all six combinations shown in figure AC 27.427-2.
All of these empirical loading distributions should be used unless rational analysis shows one or more of each set of conditions to be non-critical or equal or more realistic distributions are substantiated. Rectangular spanwise air load distribution should be used unless more rational distribution is substantiated. If end plates are used, the air loads should be distributed accordingly.
(i) First unsymmetric al loading condition:
100 percent of the flight load is applied to one side of the plane of symmetry; and 0 percent of the flight load is applied to the other side of the plane of symmetry.
(ii) Second unsymmetr ical loading condition:
50 percent of the flight load is applied to one side of the plane of symmetry acting up;
and 50 percent of the flight load is applied to the other side of the plane of symmetry acting down.
АС 27-1B 9/30/99 Figure AC 27.427-1 (View Looking Forward) Page C - 26
Figure AC 27.427-2 (View Looking Forward) Page C -27
Page C - 28
SUBPART C - STRENGTH REQUIREMENTS
GROUND LOADS
AC 27.471 § 27.471 GROUND LOADS--GENERAL .
a. Explanation . This regulation specifies that limit ground loads must be considered which are:
(1) External loads caused by l anding (ground) conditions for skid and wheel landing gear equipped rotorcraft and by ground taxiing loads as specified in § 27.235 for wheel landing gear equipped rotorcraft.
(2) Loads considering the rotorc raft structure as a rigid body.
(3) Loads in equilibrium wit h linear and angular inertia loads.
(4) The critical center of gravity “mu st be selected so that the maximum design loads are obtained in each landing gear element.”
b. Procedures .
(1) The standards to be considered are specified in §§ 27.473 through 27.505.
These associated standards cover landing gear arrangements, landing conditions, and ground loading conditions (for wheel landing gear rotorcraft).
(2) Drop tests may be used to veri fy landing load factors. (See paragraph AC 27.725.)
(3) The application of the design load s derived from the landing load factors will be as specified for each element affected by landing or ground loading conditions (for wheel landing gear rotorcraft).
(4) During the applicant’s flight test program, the landing load factors for skid and wheel landing gear rotorcraft and taxiing load factors for wheel landing gear rotorcraft are monitored to assure the design load factors used are adequate. See paragraph AC 27.235 of this document for § 27.235 policy.
AC 27.473 § 27.473 (Amendment 27- 2) GROUND LOADING CONDITIONS AND ASSUMPTIONS .
a. Explanation . The rotorcraft is to be designed for the maximum weight. A rotor lift of two-thirds of the design maximum weight may be used. The minimum limit landing load factor is determined by the drop tests of § 27.725.
Page C - 29
b. Procedures . Loads for the landing conditions are derived considering mass (equal to the maximum weight) and rotor lift (equal to two-thirds of the maximum weight) acting through the center of gravity throughout the landing impact. Unbalanced external loads resulting from asymmetric loading conditions are reacted as specified in the individual subparagraphs. The rotorcraft must be substantiated for ultimate landing loads by either test or analysis utilizing an ultimate load factor of 1.5 applied to the limit load factor of not less than that substantiated under § 27.725.
AC 27.475 § 27.475 TIR ES AND SHOCK ABSORBERS.
a. Explanation . This section specifies the tire and shock absorber position to be used in ground load derivations.
b. Procedures . Ground loads are to be derived with the tires in static (1g) position and the shock absorbers “in their most critical position.” The determination of the “most critical position” for the shock absorbers generally requires a load versus deflection test or analysis of the shock absorber system and a determination of the effect of both load and deflections on the shock absorber, attachment structure, and substructure designed by ground loads.
AC 27.477 § 27.477 LANDI NG GEAR ARRANGEMENT.
a. Explanation . This section specifies the individual standards to be used for ground load conditions for rotorcraft having two wheels aft and one or more wheels forward of the center of gravity.
NOTE: Section 27.497 gives ground loading conditions for landing gear with tail wheels, and § 27.501 gives ground loading conditions for landing gear with skids.
b. Procedures . The ground loading conditions of §§ 27.235, 27.479 through
27.485, and 27.493 will be used for rotorcraft having two wheels aft and one or more wheels forward of the center of gravity. This includes forward wheels on separate axles.
AC 27.479 § 27.479 LEVEL LANDING CONDITIONS .
a. Explanation . This section provides explicit level landing load criteria for landing gear with two wheels aft and one or more wheels forward of the center of gravity.
(1) Level landings--
(i) Each wheel contacting the ground simultaneously; and
(ii) Aft wheels contacting the ground with forward wheels just clear of the ground.
Page C - 30
(2) Application of loads--
(i) Maximum design vertical loads applied alone; and
(ii) The maximum design vertical lo ads applied with a drag load of at least 25 percent of the vertical load (applied at the ground contact area).
(3) A 40 percent/60 percent load distri bution between wheels for configurations having two forward wheels including quadricycle. This distribution between wheels on a common axis is to be applied for the conditions of vertical loads only and for vertical loads combined with drag loads of 25 percent of the vertical loads.
(4) Aircraft pitching moments are to be reacted by the forward landing gear for simultaneous wheel contact or by the angular inertia forces when the forward landing gear is clear of the ground as specified.
b. Procedures .
(1) The specified loading conditi ons will be used in load derivations.
(2) The critical center of gravity condition will be used for each gear and gear support structure.
(i) The aft center of gravity condition with the forward gear clear will normally be critical for the aft gear and gear supports.
(ii) The forward cent er of gravity condition with each gear contacting the ground simultaneously will normally design forward gear elements critical for vertical loads.
(iii) The forward cent er of gravity condition with the forward gear clear may result in high load factors, angular plus linear, that will greatly affect security of items of significant mass.
AC 27.481 § 27.481 TAIL -DOWN LANDING CONDITIONS.
a. Explanation . This section provides the criteria for tail-down landing conditions;
i.e., “the maximum nose-up attitude allowing ground clearance” with ground loads acting “perpendicular to the ground.”
b. Procedures .
(1) The tail-down landing condition will be used to check (by analysis or test) for criticality of landing gear or support structure. This attitude generally creates the highest forward loads on the main landing gear in combination with vertical loads.
Page C - 31
(2) The tail-down landing condition ma y be the critical condition for both landing load factor and for energy absorption by the main gear. Section 27.725 requires that “each landing gear must be tested in the attitude simulating the landing condition that is most critical.” Where questions exist as to the critical attitude, both level landing and tail-down landing attitudes should be used in drop tests required by § 27.725.
AC 27.483 § 27.483 ONE-WHEEL LANDING CONDITIONS .
a. Explanation . This section gives the condition to be used for one-wheel landing conditions. Only the vertical load condition of § 27.479(b)(1) is required.
b. Procedures . The one-wheel landing condition is generally critical for the landing gear-to-fuselage attachments and the landing gear elements between the attachments. Unbalanced external loads are reacted by rotorcraft inertia.
AC 27.485 § 27.485 LATERAL DRIFT LANDING CONDITIONS .
a. Explanation .
(1) This section provides the l oading conditions which impose side (and vertical) loads on the landing gear. A level landing attitude is specified. Two main conditions required are--
(i) Only the aft wheels in contact with the ground; and
(ii) All wheels contac ting the ground simultaneously.
(2) Loads. The vertical loads to be appl ied with the side loads are specified as “one-half of the maximum ground reactions of § 27.479(b)(1).” These vertical loads are the level landing loads considering both contact and noncontact with the ground by the forward wheels.
(i) One side load condition is specifi ed as “0.8 times the vertical reaction acting inward on one side and 0.6 times the vertical reaction acting outward on the other side” when only the aft wheels contact the ground.
(ii) The other side load conditi on (for all wheels contacting the ground) specifies the 80 percent inward/60 percent outward distribution for the aft wheels and
0.8 times (80 percent) the vertical reaction for the forward wheels.
b. Procedures . The loading conditions, as specified, are applied to the landing gear and attaching structure. The loads are applied at the ground contact point, except for full swiveling gear which has the load applied at the center of the axle. In other words, full swiveling gear is considered to have swiveled to a static position under the side load before the design vertical and side loads are achieved. The rotorcraft as well as the landing gear itself will be substantiated for these side load conditions.