CHAPTER 3 - MISCELLANEOUS GUIDANCE (MG),
NORMAL CATEGORY ROTORCRAFT
AC 27 MG 1 Certification Procedure for Rotorcraft Avionics Equipment..............................MG 1-1 AC 27 MG 2 Standardized Test Procedure for Rotorcraft DC ..............................................MG 2-1 Electrical System Tests AC 27 MG 3 Definition of Engine Isolation Features as Applied to ......................................MG 3-1 §§ 27.79(b)(2), 27.141(b)(1), and 27.143(d)(1) AC 27 MG 4 Full Authority Digital Electronic Controls (FADEC) ..........................................MG 4-1 AC 27 MG 5 Agricultural Dispensing Equipment Installation................................................MG 5-1 AC 27 MG 6 Emergency Medical Service (EMS) Systems, Installations,.............................MG 6-1 Interior Arrangements, and Equipment AC 27 MG 7 Hour Meters or Time-in-Service Recording Devices in Rotorcraft ...................MG 7-1 AC 27 MG 8 Substantiation of Composite Rotorcraft Structure............................................MG 8-1 AC 27 MG 9 Rotorcraft One-Engine-Inoperative (OEI) Power Assurance ...........................MG 9-1 AC 27 MG 10 Advisory Material for Substantiation of Emergency .......................................MG 10-1 Flotation System AC 27 MG 11 Fatigue Evaluation of Rotorcraft Structure.....................................................MG 11-1 AC 27 MG 12 External Loads (see AC 27.865B) .................................................................MG 12-1 AC 27 MG 13 Systems Certification Considerations ............................................................MG 13-1 AC 27 MG 14 Certification Procedure for Installation of Vapor Cycle Air Conditioning ........MG 14-1 Systems AC 27 MG 15 Airworthiness Approval of Rotorcraft Health Usage Monitoring.....................MG 15-1 Systems (HUMS) AC 27 MG 16 Certification Procedure for Rotorcraft Night Vision Imaging ..........................MG 16-1 Systems (NVIS) Equipment AC 27 MG 17 (reserved) ......................................................................................................MG 17-1 AC 27 MG 18 Helicopter Terrain Awareness and Warning System (HTAWS) ....................MG 18-1
AC 27 Appendix A - Instructions for Continued Airworthiness............................................... Apdx A-1 AC 27 Appendix B - Airworthiness Guidance for Rotorcraft Instrument Flight....................... Apdx B-1 AC 27 Appendix C - (reserved) (Criteria for Category A) .....................................................Apdx C-1
AC 27-1B, Chg 2 4/25/06
FIGURES
The first digits in the figure number are the same as the related paragraph number. The digits after the hyphen are the number within the paragraph. Most figures are located at the end of the related paragraph.
Figure No. Title Page
AC 27.45-1 H-V Requirements B-19
AC 27.45-2 IGE Controllability Requirements B-20
AC 27.45-3 Shaft Horsepower vs. Turbine Outlet B-21 Temperature - Sea Level Standard Day
AC 27.45-4 Uninstalled Takeoff Power Available B-22
AC 27.45-5 Installed Takeoff Power Available, Anti-Ice Off, B-23 400 RPM
AC 27.45-6 Power Assurance Check Chart B-24
AC 27.71-1 Autorotational Characteristics - Typical B-31
AC 27.79-1 Height-Velocity Diagram B-43
AC 27.79-2 Altitude/Wei ght Accountability B-44
AC 27.175-1 Static Longi tudinal Stability B-58
AC 27.251-1 Demonstration Points B-70
AC 27.337-1 Load Factor Gross Weight Curve C-7
AC 27.351-1 Sample Yaw/Forward Speed Diagram C-12
AC 27.351-2 Safety Factors for Probability of Failure C-13
AC 27.427-1 View Looking Forward C-26
AC 27.427-2 View Looking Forward C-27
AC 27.562-1 Seat Restraint System Dynamic Tests C-47
AC 27.562-2 Schematic Floor Defo rmation Fixture; Seat Legs C-54 Attached at Floor Level
Figure No. Title Page
AC 27.562-3 Schematic Test Fixt ure; Side Wall Mounted Seat C-58
AC 27.562-4 Installation of Pe lvic-Lumbar Spine Load Cell C-62 in Part 572B Anthropomorphic Dummy
AC 27.562-5 Measurement to be Ta ken Over Full Width of C-74 Seat Bottom Cushion
AC 27.562-6 Post Test Condition C-74
AC 27.562-7 Impulse Shape C-80
AC 27.562-8 Change in Velocity C-80
AC 27.571-1 Comparison Percent of Time in Level Flight C-85
AC 27.621-1 Example of Cast ing Load Sheet Retract D-24 Actuator Support-Landing Gear
AC 27.621-2 Example of Casti ngs to be Static Tested D-26 for Model XYZ
AC 27.773-1 Cockpit Visibility D-67
AC 27.801-1 Sea State Code - World Meteorological D-90 Organization
AC 27.865B-1 U.S. Operational (Part 133) Rotorcraft-Load D-116 Combination Versus Applicable Cargo Type Data and Definition Summary
AC 27.931-1 Cantilevered Shaft, First Critical Speed E-25
AC 27.931-2 Shaft Between Support Bearings, First Critical E-25 Speed
AC 27.952-1 Static Tensi on and Shear Loading Modes E-50
AC 27.952-2 Hose Assembly Tests E-51
AC 27.952-3 Minimum Average and Individual Loads for Hose E-52 and Hose-End Fitting Combinations
AC 27.952-4 Typical Method of Breakaway Fuel Fitting Load E-53 Calculations
AC 27-1B, Chg 2 4/25/06 Figure No. Title Page
AC 27.952-5 Typical Methods of Frangible or Deformable E-54 Attachment Load Calculations, Frangible Bolts
AC 27.952-6 Typical Methods of Frangible or Deformable E-55 Attachment Load Calculations, Frangible Baffle
AC 27.955-1 Fuel Flow E-61
AC 27.1041-1 Additional Cooling Test Point E-93
AC 27.1191-1 Table of Materials and Gauges Acceptable for E-131 Fireproof Protective Devices with Flat Surface Geometries
AC 27.1329-1 Deviation Profile F-48
AC 27.1329-2 Operational Limitation F-49
AC 27.1419-1 Continuous Icing-Temper ature vs. Altitude Limits F-93
AC 27.1419-2 Intermittent Icing-Tem perature vs. Altitude Limits F-94
AC 27.1419-3 Continuous Icing-Li quid Water Content vs Drop F-95 Diameter
AC 27.1419-4 Intermittent Icing-Li quid Water Content vs. Drop F-96 Diameter
AC 27 MG 3-1 Part 29 Engine Isolation Rules MG 3-5
AC 27 MG 5-1 Acceptable Ultim ate Load Factor for MG 5-2 Agricultural Dispensing Equipment Design
AC 27 MG 5-2 Sketch of Tank Pressure Test MG 5-6
AC 27 MG 6-1 Typical Liquid Oxygen System MG 6-17
AC 27 MG 6-2 Typical Liquid Oxygen System - Using MG 6-18 Combination Valve
AC 27 MG 8-1 Schematic Diagram of Building Block Tests MG 8-16
AC 27 MG 8-2 Characterization of Impact Damage MG 8-20
Figure No. Title Page
AC 27 MG 8-3 Residual Strength vs. Time MG 8-23
AC 27- MG 8-4 Residual Str ength and Damage Size MG 8-24 Relationships for Fail-Safe Substantiation
AC 27 MG 9-1 Installed Engine Fuel Flow Capacity Check MG 9-8
AC 27 MG 11-1 Example of Variation in Time Spent in Level MG 11-7 Flight for Three Rotorcraft Types
AC 27 MG 11-2 Flight Regime to be Investigated Power-On MG 11-17 Operation
AC 27 MG 11-3 Flight Regime to be Investigated for Power-Off MG 11-17 Operation
AC 27 MG 11-4 Simplified Analytical Method for Safe Life MG 11-18 Evaluation
AC 27 MG 11-5 Typical S/N Curve for Safe Life Evaluation MG 11-18
AC 27 MG 11-6 Elements of Safe Life Determination MG 11-19
AC 27 MG 11-7 Flight Load Measurem ent Program Conditions MG 11-20 to be Investigated
AC 27 MG 11-8 Lifting Helicopt er Load Measurement MG 11-23
AC 27 MG 11-9 Example of Twin Turbine Usage Spectrum MG 11-24
AC 27 MG 14-1 Refrigeration Cycle MG 14-7
AC 27 MG 15-1 Flow Chart for Use of Mitigating Actions MG 15-8 Applied for Reduction of Software Level
AC 27 MG 15-2 Flow Chart for App lication of HUMS Specific MG 15-11 Software with a Ground Base that uses COTS Software for Operational Software
AC 27 MG 18-1 Recommended Alert Prioritization between MG 18-16 HTAWS and TCAS TA
AC 27 MG 18-2 Flight Test Matrix MG 18-19
AC 27-1B, Chg 2 4/25/06 Figure No. Title Page
AC 27 MG 18-2.1 TAWS Required Terrain Clearance (RTC) MG 18-25 by Phase of Flight
AC 27 APX B-1 Rotorcraft Dynamic Stability Requirements Apdx B-21 for IFR
Abbreviations and Definitions
AC advisory circular ACO aircraft certification office ADF automatic direction finding ADI attitude direction indicator AEO all engines operating AFCS automatic flight control systems AGL above ground level AHRS attitude heading reference system Amdt. Amendment APU auxiliary power unit ATC air traffic control BIM blade inspection method CAM cockpit area microphone CAR Civil Air Regulations CAS calibrated air speed CBIM cockpit blade inspection method CDP critical decision point CG center of gravity COTS commercial off-the-shelf CPS cycles per second CRFS crash resistant fuel system CRT cathode ray tube CVR cockpit voice recorder DER designated engineering representative DME distance measuring equipment ECAS engine caution advisory systems ECU environmental control unit EFIS electronic flight instrument system EFP engine failure point EHE exhaust heat exchanger ELT emergency locator transmitter EMC electromagnetic compatibility EMI electromagnetic interference EMS emergency medical service EOL end of life FAA Federal Aviation Administration FADEC full authority digital engine control FAR Federal Aviation Regulations FEM finite element modeling FHA functional hazard assessment FMEA failure mode and effects analysis FPM feet per minute FPS feet per second GPS global positioning system HF high frequency HIRF high intensity radiated fields HRD high rate of discharge HUMS health and usage monitoring systems HV height-velocity IAS indicated airspeed ICA instructions for continued airworthiness ICAO International Civil Aviation Organization ICS inter-communication system IFR instrument flight rules IGE in ground effect IIDS integrated instrument display system ILS instrument landing system IMC instrument meteorological conditions INS inertial navigation system ISA international standard atmosphere ISIS integral spar inspection system ITT inter-turbine temperature KCAS knots calibrated airspeed KIAS knots indicated air speed KTAS knots true airspeed LDP landing decision point LWC liquid water content MCP maximum continuous power MEL minimum equipment list MGT measured gas temperature MMEL master minimum equipment list MSL mean sea level MVD median volume diameter NDI non-destructive inspection NM nautical mile NPRM notice of proposed rulemaking NTSB National Transportation Safety Board NVG night vision goggles Page xxi
AC 27-1B, Chg 1 2/12/03 NVIS night vision imaging systems OAT outside air temperature OEI one engine inoperative OGE out of ground effect PBA pitch bias actuator PCF post crash fire PIO pilot induced oscillation PSA preliminary safety assessment PSIG pounds per square inch gauge QPL qualified parts list RFM rotorcraft flight manual RFMS rotorcraft flight manual supplement RPM revolutions per minute RTCA Radio Technical Commission of Aeronautics RVR runway visual range SAE Society of Automotive Engineers SAS stability augmentation system SCAS stability and control augmentation systems S/N stress vs. number of cycles SRM structural repair manual SSA system safety assessment STC supplemental type certificate STOL short takeoff and landing TBO time between overhaul TC type certificate TCDS type certificate data sheet TDP takeoff decision point TIA type inspection authorization TIR type inspection report TOT turbine outlet temperature TSO: technical standard order TVP true vapor pressure VBIM visual blade inspection method VFR visual flight rules VMC visual meteorological conditions VOR very high frequency omnidirectional range radio VSI vertical speed indicator V/STOL vertical/short takeoff and landing VTOL vertical takeoff and landing WAT weight, altitude, temperature Altitudes
HD density altitude HP pressure altitude
V speeds
VD diving speed VH speed in level flight with maximum continuous power VMO maximum operating limit speed VNE never-exceed speed VTOSS takeoff safety speed for Category A rotorcraft VX speed for best angle of climb VY speed for best rate of climb MMO maximum operating mach number
N speeds
NF free turbine speed NG gas generator speed NP power turbine speed NR rotor speed
Coefficients
CD coefficient of drag CL coefficient of lift CP coefficient of power CT coefficient of thrust Page xxii
CHAPTER 1. PART 21
FAR 21 - GENERAL
CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS (Amendment 21-50)
AC 21.16. § 21.16 SPECIAL CONDITIONS .
a. The Process . Chapter 2, Section 1, Paragraph 8 of the Type Certificate Handbook, Order 8110.4A, provides detailed guidance on the special conditions process. However, much of that material has been outdated with the implementation of the Aircraft Certification Directorate Program. Rotorcraft special conditions are processed through the Rotorcraft Standards Staff, ASW-110. That office will ensure coordination with the affected agency and industry elements including the Assistant Chief Counsel. All comments will be considered and the disposition documented by the Rotorcraft Directorate. ASW-100 will issue the special conditions.
b. Basis for Development .
(1) Special conditions are justified on the basis of the existing Part 27 being inadequate or inappropriate due to novel or unusual design features of the rotorcraft to be certificated.
(2) The phrase “novel or unusual” as used in § 21.16 is a very relative term. As used hereafter in applying § 21.16 to justify the issuance of special conditions, “novel or unusual” will be taken with respect to the state of technology envisaged by the applicable airworthiness standards of this subchapter. It must be recognized that in some areas which will vary from time to time, the state of the regulations may somewhat lag the state of the art in new design because of the rapidity in which the state of the art is advancing in civil aeronautical design and because of the time required to develop the experience base needed by the FAA/AUTHORITY to proceed with general rulemaking.
Applicants for type certification of a new design have the opportunity to mitigate the impact of not knowing the precise airworthiness standards to be applied for “novel or unusual design features” by consulting with the FAA/AUTHORITY early in their certification planning when such features are suspected or known by the applicant to exist. It should also be recognized that, because of the intentional objective nature of the airworthiness standards of this subchapter, many new design features which might be thought of as “novel or unusual” may already be adequately covered by existing regulations, thus obviating the need to issue special conditions.
(3) Before proposing special conditions , the certification staff should very thoroughly analyze the existing regulations and ensure they are inadequate or inappropriate in light of a new and novel design feature.
Page FAR 21 - 1
AC 21.31. § 21.31 TYPE DESIGN .
The regulatory basis for requiring data to def ine the design is contained in § 21.31.
This section is self-explanatory and broad enough in scope to give the certification staff access to sufficient data to determine compliance with Part 27.
AC 21.33. § 21.33 INSPECTION AND TESTS .
a. Applicant Responsibility . Section 21.33 requires the applicant to:
(1) Ensure the test rotorcraft confo rms to the type design. This must be accomplished prior to presentation to the FAA/AUTHORITY for testing.
(2) Conduct all inspections and tests necessary to determine compliance with the airworthiness and noise requirements.
b. FAA/AUTHORITY Responsibility .
(1) The design evaluation engineers s hould ensure that the type design is adequate in their technical area and that the inspections and tests to be conducted are appropriate and sufficient to show compliance with Part 27.
(2) As changes to the rotorcraft are made during the test program, the flight test crew should ensure that the appropriate design evaluation engineer concurs with the change and the conformity inspection of the change has been conducted.
AC 21.35 § 21.35 (Amendm ent 21-59) FLIGHT TESTS.
a. Explanation .
(1) This section outlines the require ments of the applicant for aircraft type certification and should be used in conjunction with FAA Order 8110.4A, Section 5.
Section 21.35 requires, in part, that the applicant conduct sufficient flight tests to show compliance with the flight requirements throughout the proposed flight envelope. The results of the applicant’s flight test should be submitted to the FAA/AUTHORITY in report form for evaluation to determine what verification flight tests the FAA/AUTHORITY may elect to conduct. The report should conclude that in the applicant’s opinion the test aircraft complies with the applicable certification requirements. The FAA/AUTHORITY verification flight test should include, but not be limited to, the critical or marginal results contained in the applicant’s flight test report.
The FAA/AUTHORITY’s role in the certification effort is not envisioned to be one of conducting day-to-day routine flight tests with the applicant, but only to verify his results through limited sampling. In certain tests, such as high altitude testing at a remote mountain site, there is an advantage in conducting flight tests concurrently with the applicant. Additionally, the FAA/AUTHORITY can provide technical flight test Page FAR 21 - 2
assistance to the applicant in certain cases. This can be done after a cursory review and a letter of authorization is issued to the flight test crew.
(2) Preflight Test Planning . After the applicant’s flight test report is reviewed, it should be determined what FAA/AUTHORITY engineering flight tests are necessary.
These tests are normally specified in the Type Inspection Authorization (TIA). At the same time the FAA/AUTHORITY must know and agree to the applicant’s proposed means of data acquisition, reduction, and expansion of the flight test data. The adequacy of the test instrumentation should be evaluated prior to official type certification tests (reference paragraph AC 21.39).
(3) Order of Testing . The Federal Aviation Regulations are so worded that the results of some flight tests have a definite bearing on the conduct of other tests. For this reason, and to minimize retesting, careful attention should be given to the order of testing. The exact order of testing will be determined only by considering the particular rotorcraft and test program involved. Tests which are particularly important in the early stages of the program are:
(i) Airspeed calibration: All te sts involving airspeed depend upon the calibration.
(ii) Engine power available determination.
(iii) Engine cooling.
(4) Test Groupings .
(i) Weight and c.g .: In addition to the regulatory relationship of one test to another, efficient testing requires that consideration be given to the accomplishment of as many tests on a single flight as can be accommodated successfully.
(ii) Special Instrumentation . Similarly, consideration should be given to grouping of tests that involve special instrumentation. Examples of these are takeoff and landing tests which usually require group equipment to record horizontal distance, height, and time. Ground calibration of the airspeed indicating system can be accomplished at the same time. It is the applicant’s responsibility to provide the necessary instrumentation.
(5) Functional and Reliability Testing
(i) Section 21.35(b)(2) requires that the applicant determine that “there is reasonable assurance that the aircraft, its components, and its equipment are reliable and function properly.” Section 21.35(f)(1) requires a Function and Reliability (F&R) program of 300 hours for turbine engine powered aircraft incorporating engines of a type not previously used in a type certificated aircraft. Section 21.35(f)(2) requires a 150-hour F&R program for all other aircraft. The following reflects general practices that Page FAR 21 - 3
have been used during rotorcraft certification programs. FAA/AUTHORITY have supported proposals which gave F&R test time credit for certification testing in lieu of dedicated F&R testing. In establishing such credit, the following should be considered:
(A) The point in time in which the rotorcraft reaches substantial conformity with the approved type design.
(B) The extent and comple xity of the new design.
(C) For a previously certified rotorcraft, the F&R program requirement should be commensurate with the modification or change in type design and may be zero.
(ii) Historically, for major rotorcraft type certification programs, flight time credit has been limited so as to require an irreducible minimum of 50 hours of dedicated F&R flight time. For rotorcraft programs that involved new engine installations (mature engine design) or drive train/rotor system changes on previously certified aircraft (TC amendments or STC’s), flight time credit has been liberal and often resulted in very little or no dedicated F&R testing.
b. Procedures .
(1) Type Certification Flight Tests .
(i) Prior to initiating official F AA/AUTHORITY flight tests, a conformity inspection of the test aircraft must be accomplished. This is needed to assure that the test aircraft is in the proper configuration or “conforms” to the engineering drawings and documents that have been submitted to FAA/AUTHORITY, evaluated, and approved. It is absolutely essential to know the configuration being tested in any engineering flight evaluation. Conformity inspection prior to TIA flight tests assures that testing will not be wasted because of configuration uncertainties.
(ii) FAA Order 8110. 4A, paragraph 67, contains a requirement that the applicant must keep the FAA/AUTHORITY advised of any configuration changes to the aircraft. The manufacturing inspector should keep the FAA/AUTHORITY flight test pilot apprised of any change which may affect safety of the test aircraft or may influence test results.
(iii) Results of the conformity inspection and the engineering flight test program must be documented. This is normally done in the Type Inspection Report (TIR). Results may be documented in any acceptable engineering format. The report should be in sufficient detail to clearly show how compliance with each appropriate section of the rules was determined.
(iv) The flight test pilot mu st assure that the FAA/AUTHORITY manufacturing inspector and certification engineer are aware of all configuration Page FAR 21 - 4