Page D - 108
(1) To minimize the probability of igni tion of fluids and vapors after single failure of a component or systems, the following methods may be used:
(i) Shroud and drain flammable flui d systems (including steel fluid lines, fittings, etc.) and provide the systems with fuel and vapor seals with respect to potential ignition sources (electrical wiring and equipment, hot bleed air lines, etc.).
(ii) Provide other effective separat ion, ventilation, or overheat shutdown devices, etc., to preclude ignition.
(iii) Ensure that electrical equipm ent in the areas subject to flammable fluids and vapors is either hermetically sealed or has been tested and shown to be free of ignition capability. Paragraph AC 27.1309 describes acceptable guidance for such laboratory testing.
(iv) Place a restricting orifice in fluid pressure lines routed to instruments and transducers.
(v) Ensure fluid lines are not lo cated so as to be subject to abrasion during normal operations. Cargo compartments should be evaluated for potential line damage due to cargo movement.
(2) To minimize hazards if ignition occurs:
(i) Provide fireproof designs, fire wall isolation, or equivalent means for critical structure, equipment, and personnel areas.
(ii) Consider fire detection, extinguishment, shutoff valves, fire suppression systems, etc.
(3) In considering compliance, the act ual protective measures may be related to the situation, considering the quantity and flammability characteristic of the fluid, the fire damage tolerance of the area, and the means available to the crew to minimize hazards from the fire. If action by the crew is necessary, a quick acting means ( not necessarily fire detectors) must be provided to alert the crew in the event of a fire.
Details of any action required by the crew should be included in the Rotorcraft Flight Manual.
(4) Compliance with § 27.863(d) requi res, a minimum, type design data defining each area where flammable fluids or vapors might escape.
Page D - 109
SUBPART D - DESIGN AND CONSTRUCTION
EXTERNAL LOAD ATTACHING MEANS.
AC 27.865. § 27.865 (Am endment 27-11) EXTERNAL LOAD ATTACHING MEANS.
a. Explanation .
(1) If certification for external load operations is requested, the rule requires that the external load attaching means be substantiated by test or analysis for a limit static load equal to or greater than 2.5 times the maximum external load for which certification is requested. The factor of 2.5 times the maximum external load was established as a minimum strength requirement by Part 133 operations to account for loading effects of sling-load angles up to 30° from the vertical. Allowance for reducing the 30° angle is provided if substantiated.
(2) The rule requires that a quick -release device be installed on one of the pilot’s primary controls so the pilot can quickly release the external load during an emergency situation. In addition, a backup manual mechanical control for the quick-release device is required to be readily accessible to either the pilot or another crewmember.
(3) The rule requires appropriate placards or markings stating the maximum authorized external load.
b. Procedures .
(1) The maximum external load for which authorization is requested should not exceed the rated capacity of the quick-release device. The quick-release device should be strength tested (with FAA/AUTHORITY witness) if it is not produced to a recognized industry or military standard.
(2) Substantiation of external loadi ng requirements must include any direction making an angle of 30° (with the exception of directions having a forward component).
(reference § 27.865(a).)
(i) The sling-load angle (i.e., the angl e between the vertical direction and the sling-load cable supporting the external load) should not exceed an angle of 30° to minimize the cable tension load.
(ii) The 30° angle may be reduced if an operating limitation is established limiting external load operations to such angles for which compliance has been shown or if the reduced angle cannot be exceeded in service. The lesser angle should be substantiated by flight testing.
Page D - 110
(3) The external load releasing system is specified to include a quick release device installed on one of the pilot’s primary controls. It is usually installed on the cyclic stick to allow the pilot to release the load with minimum distraction after maneuvering the load into the release position.
(4) A manual mechanical control for t he quick-release device is specified to be installed and be readily accessible to the pilot or to another crewmember. A sufficient amount of slack should be provided in the control cable to permit complete cargo movement without tripping the cargo release.
AC 27.865A. § 27.865 (Amendment 27-26) EXTERNAL LOAD ATTACHING MEANS.
a. Explanation . Amendment 27-26 added two requirements to § 27.865:
(1) Section 27.865(a) is clarified to al low use of a design factor less than 2.5g’s, for rotorcraft load combinations A, B, and C non-human external cargo applications provided the lower load factor is not likely to be exceeded by virtue of the rotorcraft characteristics and capability. That is, the rotorcraft design factors may be used for the cargo device system.
(2) Section 27.865(d) was added to clarif y and specify the fatigue requirements for the external cargo attaching means.
b. Procedures . All of the policy material pertaining to this section remains in effect with the following additions:
(1) For § 27.865(a), if a design limit lo ad factor less than 2.5g’s is requested, the applicant should provide a rational analysis and/or a flight operations data base that clearly shows that the load factor requested is unlikely to be exceeded in service.
NOTE: § 27.337(b) requires use of 2.0 g’s as a minimum.
(2) § 27.865(d), all failures of the car go attaching means (and the associated critical components) that are likely to be hazardous to the rotorcraft should be identified by an acceptable means, such as a Failure Mode Effect Analysis (FMEA). The critical components associated with these failure modes should receive a fatigue analysis and/or test to ensure that the likelihood of a failure occurring is minimized. In the majority of cases, an analysis using the methods of AC 27 MG 11, “Fatigue Evaluation of Rotorcraft Structure”, will be sufficient. If any component has a service life and/or mandatory inspection these components and each mandatory life should be identified, approved, and placed in the airworthiness limitations section of the maintenance manual or Instructions for Continued Airworthiness. See paragraph AC 27.1529 for information on these manuals.
Page D - 111 AC 27.865B. § 27.865 (Amendment 27-36) EXTERNAL LOAD ATTACHING MEANS.
a. Background. The standards for external load attaching means, transport and normal category rotorcraft were originally contained in Subpart D, "Airworthiness Requirements of 14 CFR Part 133, Rotorcraft External-Load Operations."
Amendment 29-12, issued in 1977, added a new § 29.865, which moved these standards from Part 133 to Part 29. An identical transfer occurred in 1977 for Part 27.
Amendment 29-26, issued in 1990, clarified the intent of Amendment 29-12 but did not change it substantively. Transport Categories A and B and Normal Category rotorcraft were initially used under Part 133 operations, and after Amendment 133-6, restricted category rotorcraft were also included under Part 133 operations. The carriage of persons external to the rotorcraft for hire first came about when a Part 29 operator, exempt from Part 133, transferred harbor pilots to and from ships by a hoist and sling.
The exemption was granted to study the feasibility of passenger transfer outside of the cabin. Grant of the exemption was based, in part, on similar, prior operations that had been conducted in Europe and Africa, for hire, with helicopters approved by the appropriate authorities and, in part, on similar military and public helicopter operations, not for hire, in the U.S. Subsequently, Amendment 133-9,adopted in January 1987, established a new Class D rotorcraft load combination (RLC) for transporting loads other than Class A, B, or C that are specifically approved by the Administrator external to the rotorcraft. Amendment 133-9 also provided for the limitations and conditions for transport of external loads other than Class A, B, or C and the necessary, associated safety requirements. Part 27 rotorcraft are not eligible for RLC Class D, because of the current restriction of § 133.45(e) that limits use of RLC Class D to Part 29 Category A rotorcraft (under the performance limits prescribed in § 133.45(e)). Part 29 has recently been changed to reflect RLC Class D requirements. Also, the scope and thus the title of the standard have changed from "External load attaching means" to "External loads" to reflect the more comprehensive approach for external loads required to assure the proper level-of safety.
b. Explanation.
(1) This advisory material contains guidance for certification of helicopter external load attaching means and load carrying systems to be used in conjunction with operating rules such as Part 133, "Rotorcraft External Load Operations." Subpart D of Part 133 contains supplemental airworthiness requirements. 14 CFR Part 1 defines four RLC classes that (with the exception of RLC Class D due to the restriction of
133.45(e)) are approvable under Part 133 operating rules and that are eligible for certification under § 27.865. The three RLC classes (and their eligibility for Part 27 use based on operational requirements) are summarized in FIGURE AC 27.865-1 and discussed in paragraph d. Under operating rules RLC Classes A, B, and C are eligible, under specific restrictions, for both human external cargo (HEC) and nonhuman external cargo (NHEC) operations. However, under the operating rules, only RLC Class D is eligible for transporting HEC for compensation (see Figure AC 27.865-1).
For further information, AC 133-1A, "Rotorcraft External-Load Operations in Accordance
AC 27-1B, Chg 2 4/25/06
Page D - 112 with 14 CFR Part 133," October 16, 1979, may be reviewed. Also, paragraph AC 27.25 (reference § 27.25) concerns, in part, jettisonable external cargo.
(2) Section 27.865 provides a minimum level of safety for normal category rotorcraft designs to be used with operating rules such as Part 133. Certain aspects of operations such as microwave tower and high-line wirework may also be regulated separately by other Federal agencies such as DOE, EPA, and OSHA or by other international entities. For applications that could come under multiple agency regulation (or regulation by other entities), special certification emphasis will be required by both the applicant and the approving authority to assure all relevant safety requirements are identified and met. Potential additional requirements, where thought to exist, are noted herein.
c. Definitions.
(1) Applicable cargo type. The ca rgo type (i.e., non-human external cargo (NHEC), human external cargo (HEC), or both) that each RLC Class is eligible to use by regulation (Figure AC –27.865-1 contains explicit definitions for U.S. Part 133 Operations).
(2) Backup Quick-Release Subsystem (BQRS). The secondary or "second choice" subsystem used to perform a normal or emergency jettison of external cargo.
(3) Cargo. The part of any Rotorcra ft-Load Combination that is removable, changeable, and is attached to the rotorcraft by an approved means.
(4) Cargo hook. A hook that can be ra ted for both HEC and NHEC. It is typically used by being fixed directly to a designated hardpoint on the rotorcraft.
(5) Dual actuation device (DAD). This is a sequential control that requires two distinct actions in series for actuation. One example is removal of a lock pin followed by a "then free" switch or lever activation for load release to occur (in this scenario, a load release switch protected only by an uncovered switch guard is not acceptable). For jettisonable HEC applications, a simple covered switch does not qualify as a DAD.
Familiarity with covered switches allows the pilot to both open and activate the switch in one motion. This has led to inadvertent load release.
(6) Emergency jettison (or complete load release). The intentional, instantaneous release of NHEC or HEC in a preset sequence by the quick release system (QRS) that is normally performed to achieve safer aircraft operation in an emergency.
(7) External fixture. A structure external to and in addition to the basic airframe that does not have true jettison capability and has no significant payload capability in addition to its own weight. An example is an agricultural spray- boom. These configurations are not "External Loads" approvable under § 27.865.
Page D - 113
(8) Hoist. A hoist is a device that exer ts a vertical pull, usually through a cable and drum system (i.e., a pull that does not typically exceed a 30-degree cone measured around the z-rotorcraft axis).
(9) Hoist demonstration cycle (or "one cycle"). The complete extension and retraction of at least 95 percent of the actual cable length, or 100 percent of the cable length capable of being used in service (i.e., that would activate any extension or retraction limiting devices), whichever is greater.
(10) Hoist load-speed combinations. Some hoists are designed so that the extension and retraction speed slows as the load increases or nears the end of a cable extension. Other hoist designs maintain a constant speed as the load is varied. In the latter design, the load-speed combination simply means the variation in load at the constant design speed of the hoist.
(11) Human external cargo (HEC). A person(s) that at some point in the operation is carried external to the rotorcraft. (Figure AC 27.865-1 contains explicit definitions for U.S. Part 133 Operations). See Nonhuman external Cargo (NHEC).
(12) Nonhuman external cargo (NHEC). Any external cargo operation that does not at any time involve a person(s) carried external to the rotorcraft (figure AC 27.865-1 contains explicit definitions for U.S. Part 133 Operations).
(13) Normal jettison (or selective l oad release). The intentional release, normally at optimum jettison conditions, of an NHEC.
(14) Personnel carrying device system (PCDS). The entire attached or suspended system used to carry HEC. This is any HEC carrying configuration such as a suspended (e.g., hoist, cable, harness) HEC system or an attached (e.g., a rigid basket or cage attached to skids) HEC system. (See TSO C167)
(15) Primary Quick-Rele ase Subsystem (PQRS). The primary or "first choice" subsystem used to perform a normal or emergency jettison of external cargo.
(16) Quick-release system (QRS). Th e entire release system for jettisonable external cargo, (i.e., the sum total of both the primary and backup quick-release subsystems). The QRS consists of all components including the controls, the release devices, and everything in between.
(17) Rescue hook (or hook). A hook that can be rated for both HEC and NHEC. It is typically used in conjunction with a hoist or equivalent system.
(18) Rotorcraft-load combination (RLC). The combination of a rotorcraft and an external-load, including the external-load attaching means. Rotorcraft-load combinations are designated as Class A, Class B, Class C, and Class D, as follows:
AC 27-1B, Chg 2 4/25/06
Page D - 114
(i) Class A rotorcraft-load combinat ion means one in which the external load cannot move freely, cannot be jettisoned, and does not extend below the landing gear.
(ii) Class B rotorcraft-load combinat ion means one in which the external load is jettisonable and is lifted free of land or water during the rotorcraft operation.
(iii) Class C rotorcraft-load combination means one in which the external load is jettisonable and remains in contact with land or water during the rotorcraft operation.
(iv) Class D rotorcraft-load combinat ion means one in which the externalload is other than a Class A, B, or C and has been specifically approved by the Administrator for that operation. RLC Class D operations are not allowed for Part 27 rotorcraft (Re: 133.45(e) restriction).
(19) Spider: A spider is a system of attaching a lowering cable or rope or a harness to a NHEC (or HEC) RLC to eliminate unwanted flight dynamics during operations. A spider usually has four or more legs (or load paths) that connect to various points of a PCDS to equalize loading and prevent spinning, twisting, or other undesirable flight dynamics.
(20) True jettison capability. The ability to safely release an external load using an approved QRS in 30 seconds or less.
NOTE: In all cases, a PQRS should release the external load in less than 5 seconds.
Many PQRS's will release the external load in milliseconds, once the activation device is triggered. However a manual BQRS, such as a set of cable cutters, could take as much as 30 seconds to release the external load. The 30 seconds would be measured starting from the time the release command is given and ending when the external load is cut loose.
(21) True payload capability. The ability of an external device or tank to carry a significant payload in addition to its own weight. If little or no payload can be carried, the external device or tank is an external fixture (see definition).
(22) Type inspection authorization (TIA). This is FAA Form 8110-1. It is used for authorizing official ground inspections and flight-tests necessary to fulfill the requirements for type certification or supplemental type certification. Order 8110.4, Chapter 2, Section 1, Paragraph 16, states the criteria for TIA issuance.
(23) Winch. A winch is a device t hat can employ a cable and drum or other means to exert a horizontal (i.e., x-rotorcraft axis) pull. However, since a winch can be used to perform a hoist function by use of a 90-degree cable direction change device (such as a pulley or pulley system), a winch system may be considered a hoist.
Page D - 115
d. Procedures . The following certification procedures are provided in the most general form. Where there are significant differences between the cargo types, these differences are highlighted.
(1) General Compliance Procedures for § 27.865 : The applicant should clearly identify both the Rotorcraft Load Combinations (RLC) and the applicable cargo types (NHEC or HEC) for which application is being made. The structural loads and operating envelopes for each RLC class and applicable cargo type should be determined and used to formulate the flight manual supplement and basic loads report.
The applicant should show by analysis, test, or both, that the rotorcraft structure, the external load attachment means, and the PCDS, if applicable, meet the specific requirements of §§ 27.865, 133.41, 133.43, 133.45, and the other relevant requirements of Part 27 for the proposed operating envelope.
NOTE: It is possible, ifapproved, to carry both HEC and NHEC externally, simultaneously as two separate external loads. However, in no case is it intended that the approved Maximum Internal Gross Weight be exceeded for any approved HEC configuration (or combined NHEC and HEC configuration) in normal operations.
Reliability of the external load system. The failure of the external load system, including the PCDS where applicable, and its attachments to the rotorcraft should be shown to be extremely improbable (i.e., 1 x 10-9 failures per flight) for all failure modes that could cause a catastrophic failure, serious injury, or a fatality anywhere in the total airborne system. All significant failure modes of lesser consequence should be shown to be improbable (i.e., 1 x 10-5 failures per flight). An acceptable method of achieving this goal is to submit and achieve approval of all of the following:
(i) A failure modes and effects analys is (FMEA) showing that all potential failure modes of the airborne system which may result in catastrophic failures, serious injuries, or fatalities are extremely improbable and any less significant failures are improbable.
(ii) A repetitive test of all functi onal devices that cycles these devices at least 30 times under critical structural conditions, operational conditions, or a combination of both.
(iii) An environmental qualificat ion review over the proposed operating environment.
AC 27-1B, Chg 2 4/25/06
Page D - 116 Figure AC 27.865B-1 U.S. OPERATIONAL (PART 133) ROTORCRAFT-LOAD COMBINATION
VERSUS APPLICABLE CARGO TYPE DATA AND DEFINITION SUMMARY
Possible RLCs and Cargo Types Category “A” Rating and OEI Hover Capability
Notes Direct 2-Way Voice Communications Required See Paragraph d(10) RLC A, HEC No Note 2 No RLC A, NHEC No N/a RLC B, HEC No Note 2 No RLC B, NHEC No N/A RLC C, HEC No Note 2 No RLC C, NHEC
N/A N/A RLC D, HEC Note 1 Note 1 Note 1
NOTES:
1. RLC Class D operations are not allowed for Part 27 rotorcraft (Re: 133.45(e) restriction).
2. A person who is not being carried or transported for compensation, is knowledgeable of the risks involved, and at some point is required to be outside of the rotorcraft in order to fulfill the mission. These persons are considered as RLC Class A, B, or C HEC as appropriate to the operation.
Page D - 117
(2) § 27.865(a) Static Struct ural Substantiation Procedures: The following static structural substantiation methods should be used.
(i) Critical basic load determination . The critical basic loads and corresponding flight envelope are determined by statically substantiating the gross weight range limits, the corresponding vertical limit load factors (NZW) and safety factors applicable for the type of external load for which the application is being made.
Note: In cases where NHEC or HEC can have more than one shape, center-of-gravity, center-of-lift, or be carried at more than one distance in flight from the rotorcraft attachment, a critical configuration for certification purposes may not be determinable.
If such a critical configuration can be determined, it may be examined for approval as a "worst case" to satisfy a particular certification criterion or several criteria, as appropriate. If such a critical configuration cannot be determined, the extreme points of the operational – external load configuration envelope should be examined with consideration given to any other points within the envelope which experience or other rationale would indicate should be investigated.
(ii) Vertical Li mit and Ultimate Load Factors. The basic NZW is converted to ultimate load by multiplying the maximum vertical limit load by the appropriate safety factor. (For restricted category approvals, see guidance in paragraph AC 27 MG 5.)
This ultimate load is used to substantiate all existing structure affected by, and all added structure associated with, the load carrying device, its attachments and its cargo.
Casting factors, fitting factors, and other dynamic load factors should be applied where appropriate.
(A) NHEC applications. In most cases, it is acceptable to perform a standard static analysis to show compliance. A vertical limit load factor (NZW) of 2.5 g is typical for heavy gross weight NHEC hauling configurations (reference § 27.337). This vertical load factor should be applied to the maximum external load for which application is being made, together with a minimum safety factor of 1.5.
(B) HEC applications. If a safety factor 3.0 or more is used, it is acceptable to perform a standard static analysis to show compliance. The safety factor should be applied to the yield strength of the weakest component in the system (QRS, PCDS, and attachment load path). If a safety factor of less than 3.0 is used, both an analysis and a full-scale ultimate load test of relevant parts of the system should be submitted.
Since HEC applications typically involve lower gross weight configurations, a higher vertical limit load factor is required to assure that limit load is not exceeded in service.
The applicant should use either the conservative value of 3.5 g’s or an analytically derived maximum vertical limit load factor for the requested operating envelope. Linear interpolation between the vertical load factors of maximum and minimum design weights
AC 27-1B, Chg 2 4/25/06
Page D - 118 may be used. However, in no case may the vertical limit load factor be less than 2.5 g's for any RLC application for HEC.
For the purpose of structural analysis or test, assume a 223-pound man as the minimum weight of each occupant carried as HEC.
Note: If the HEC is engaged in work tasks that employ devices of significant added weight (heavy backpacks, tools, fire extinguishers, etc.), the total weight of the 223-pound man and equipment should be assumed in the structural analysis or test.
(iii) Critical Structural Case . For applications involving more than one RLC class or cargo type, the structural substantiation is required only for the most critical case. The most critical case should be determined by rational analysis.
(iv) Jettisonable Loads . For the substantiating analyses or tests of all jettisonable RLC external loads, including HEC, the maximum external load should be applied at the maximum angle that can be achieved in service but not less than 30 degrees. The angle should be measured from the sling-load-line to rotorcraft vertical axis (z axis) and may be in any direction that can be achieved in service. The 30-degree angle may be reduced in some or all directions if it is impossible to obtain due to physical constraints or operating limitations. The maximum allowable cable angle should be determined and approved. The angle approval should be based on structural requirements, mechanical interference limits, and flight handling characteristics over the most critical conditions and combinations of conditions in the approved flight envelope.
(v) Hoist system limit load .
Note: In cases where hoist cables or long-line cables are utilized, a new dynamic system is established. Characteristics of the system should be evaluated to assure that either no hazardous failure modes exist or that they are acceptably minimized. For example, the cable or long line may exhibit a natural frequency that could be excited by sources internal to the overall structural system (i.e., the rotorcraft) or by sources external to the system. Another example is the loading effect of the cable acting as a spring between the rotorcraft and the suspended external load.
(A) Determine the basic loads that re sult in the failure or unspooling of the hoist or its installation, respectively.
NOTE: This determination should be based on static strength and any significant dynamic load magnification factors.
(B) Select the lower of the two va lues as the ultimate load of the hoist system installation.
Page D - 119 (C) Divide the selected ultimate load by 1.5 to determine the true structural limit load of the system.
(D) Determine the manufacturer' s approved (or applicants applied for) "limit design safety factor." Divide this factor into the true structural limit load (from (C) above) to determine the hoist system's working (or placarded) limit load.
(E) Compare the system's deriv ed limit load to the applied for one "g" payload multiplied by the maximum downward vertical load factor (NZWMAX) to determine the critical payload's limit value.
(F) The critical limit payload s hould be equal to or less than the system's derived limit load for the installation to be approvable.
(3) § 27.865(b) and § 27.865(c) Procedures for Quick Release Systems and Cargo Hooks: For jettisonable RLC's of any applicable cargo type, both a primary quick-release system (PQRS) and a back-up quick-release system (BQRS) are required. Features that should be considered are:
(i) The PQRS, BQRS and their load release devices and subsystems (such as electronically actuated guillotines) should be separate (i.e., physically, systematically, and functionally redundant).
(ii) The controls for the PQRS should be installed on one of the pilot's primary controls, or in an equivalently accessible location. The use of an "equivalent accessible location" should be reviewed on a case-by-case basis and used only where equivalent safety is clearly maintained.
(iii) The controls for the BQRS ma y be less sophisticated than that of the PQRS. For instance, manual cable cutters are acceptable provided they are listed in the flight manual as a required device and have a dedicated, placarded storage location.
(iv) The PQRS should release the external load in less than 5 seconds.
The BQRS should release the external load in less than 30 seconds. This time interval begins the moment an emergency is declared and the ends when the load is released.
(v) Each quick-release device should be designed and located to allow the pilot or a crewmember to accomplish external cargo release without hazardously limiting the ability to control the rotorcraft during emergency situations. The flight manual should reflect the requirement for a crewmember and the related functions.
(vi) Other load release types . In some current configurations, such as those used for high line operations, a load release may be present that is not on the rotorcraft but is on the PCDS itself. Examples are a tension release device that lets out