AC 27-1B

Change 1-2Historical

Advisory circular · Certification of Normal Category Rotorcraft

A newer version is currentThis is a historical version. AC 27-1B CHG 1-9 is the version in force, approved June 23, 2023.
Approved
April 25, 2006
Last reviewed
December 4, 2008
Family
AC 27-1 · 10 versions
Revision
B, change 2
14 CFR parts
27
Cited by
1 AD

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 22, 2025.

Show pages 44–55

CERTIFICATION BASIS

.

FAR 27 CAR 6 CAR 06 Rqmts 27-Amdt. 21 27-Amdt. 2 Original 6-Amdt. 7 6-Amdt. 4 Original Original H-V Ref.

27.25

27.79

27.1519

27.1587

6.116

6.741

6.743 Test Conditions

1. MGW Sea Level

2. Max. OGE wt. Lesser of:

a. Max. alt. cap.

b. 7000' Hd

1. MGW Sea Level

2. Wt. selected by applicant at lessor of:

a. Max. alt. cap.

b. 7000' Hd

1. MGW Sea Level

2. Wt. selected by applicant at lessor of:

a. Max. alt. cap.

b. 7000' Hd

1. MGW Sea Level

2. Wt. selected by applicant at lessor of:

a. Max. alt. cap.

b. 7000' Hd

1. MGW Sea Level

2. Wt. selected by applicant max. t.o. and ldg. alt.

1. MGW Sea Level

2. Wt. selected by applicant at max. t.o. and ldg. alt.

1. No specific wt. and alt.

requirements.

RFM

3. H-V is perf.

Info.

4. Max. alt. For which H-V is valid

3. H-V is perf.

info.

4. If H-V wt is less than IGE wt., wt. becomes limitation for

t.o./ldg.

3. H-V is perf.

info.

3. H-V is perf.

info.

3. H-V is perf.

info.

3. H-V is operating limitation.

H-V is operating limitation.

AC 27- 1B Para AC

27.45 & AC

27.51 Remarks

5. If H-V is less than OGE wt., H-V wt. becomes limit.

6. Applicant is encouraged to demo H-V to WAT limits.

7. Hover data may be shown above 7000' if H-V & IGE are demo'd to 7000' FIGURE AC 27.45-1 H-V Requirements

Page B - 19

CERTIFICATION BASIS

FAR 27 CAR 06 Rqmts 27-Amdt. 21 Original Original Original IGE

CONTROL Ref.

27.25

27.143

27.1587 AC 27-1B Para AC 27.45 & AC 27.143 Test Conditions

1. MGW Sea Level

2. Max. IGE wt.

Lesser of:

a. Max. alt. cap.

b. 7000' Hd

3. Critical CG

4. Critical Rotor RPM

5. Wind of not less than 17 kts.

1. MGW Sea Level

2. Wt. selected by applicant to max.

t.o. and ldg. alt.

3. Critical CG

4. Critical Rotor RPM

5. Critical wt.

6. Wind of not less than 20 mph

1. MGW Sea Level

2. Max. approved wt.

for t.o./ldg at alt above sea level.

3. Critical CG

4. Critical Rotor RPM

5. Wind not less than 20 mph.

1. No specific requirement.

RFM 6. Max. safe wind is perf. info. 7. Max. safe wind is perf. info. 6. Max. safe wind is perf. info.

Remarks

7. If 17 kts. wind demo'd to alt. less than 7000', a corresponding WAT limit must be established.

FIGURE AC 27.45-2 IGE CONTROLLABILITY REQUIREMENTS

Page B - 20

Page 58OCROpen in PDF

600 500 CORRECTED SHAFT HORSEPOWER ENG S/N 12345 400 300 MIN CERTIFIED

SPECIFICATION ENGINE 200 100 1000 1100 1200 1300 1400 1500 CORRECTED TOT °F FIGURE AC 27.45-3 SHAFT HORSEPOWER VS TURBINE OUTLET

TEMPERATURE - SEA LEVEL STANDARD DAY Page B - 21

Page 59OCROpen in PDF

20 -10° -30° to -50° 50° 16 PRESSURE ALTITUDE - FEET (X 1000) O L 200 300 400 500

SHAFT HORSEPOWER AVAILABLE FIGURE AC 27.45-4 UNINSTALLED TAKEOFF POWER AVAILABLE Page B - 22

Page 60OCROpen in PDF

20 18 ·0 > 10-501 C -20 ° 0 14 TRANSMISSION LIMIT PRESSURE ALTITUDE - FEET (X 1000) 200 300 400

SHAFT HORSEPOWER AVAILABLE FIGURE AC 27.45-5 INSTALLED TAKEOFF POWER AVAILABLE, ANTI-ICE OFF, 400 RPM Page B - 23

Page 61OCROpen in PDF

CECCE EXAMPLE: OAT = 17.5°C TOT = 760° C Hp = 4000 FT REQUIRED TORQUE = 70% 80 100 PERCENT TORQUE FIGURE AC 27 45-6 POWER ASSURANCE CHECK CHART ZERO AIRSPEED GENERATOR LOAD 100 AMPS 40 CONDITIONS: RPM 100% ANTI-ICE OFF 10 800°C 780°C 760°C 740°C 720°C 700°C 680°C 660°C Page B - 24

AC 27.51. § 27.51 TAKEOFF.

a. Explanation . Section 27.51 details the conditions under which takeoff data must be obtained. The flight manual must contain the technique(s) to be used to obtain the published flight manual takeoff procedures. Technique should not be confused with exceptional pilot skill and/or alertness as mentioned in § 27.51. Because rotorcraft differ, different pilot techniques are sometimes required to achieve the safest and most optimum takeoff performance. The recommended technique that is published in the flight manual must be determined to be one that the operational pilot can duplicate using the minimum amount of type design cockpit instrumentation and the minimum crew. Only rotorcraft takeoff techniques will be covered in this section.

b. Background .

(1) Certain special takeoff techniques are necessary when a rotorcraft is unable to take off vertically because of altitude, weight, power effects, or operational limitations.

The recommended technique used to take off under such conditions is to accelerate the rotorcraft in-ground-effect (IGE) to a predetermined airspeed prior to climbout. Takeoff tests are performed to determine the best repeatable technique(s) for a particular rotorcraft over the range of weight and altitude for which certification is requested.

(2) Utilizing the total power available to execute a takeoff may not be operationally feasible due to such items as HV or aircraft attitude constraints. In such situations, hover power required plus some power increment may be the maximum recommended for use.

(3) Wheel or skid height shoul d be not less than that demonstrated satisfactorily for the high speed, low altitude portion of the HV curve, or that height below which ground contact may occur when accomplishing takeoff procedures.

(4) For rotorcraft fitted with wheel s, a running takeoff procedure may be accepted.

c. Procedures .

(1) There are different takeoff profiles which may be used to complete a maximum performance takeoff in a rotorcraft. The manufacturer will normally determine which method is best for a particular rotorcraft. The most commonly accepted method is the hover and level acceleration technique. In this technique, the rotorcraft is stabilized in a hover at the reference height. From the stabilized hover, the rotorcraft is accelerated to the climbout airspeed using the predetermined takeoff power. When the desired climbout airspeed is achieved, the rotorcraft is rotated and the climbout is accomplished at the scheduled airspeed(s) and constant rotor RPM. Power adjustments may be accomplished to maintain the targeted power except where procedure requires high workload outside the cockpit (i.e., that portion of takeoff where horizontal acceleration close to the ground has pilot scan outside the cockpit and Page B - 25

adjustment of engine torque or temperature would require an undue increase in workload). The recommended takeoff procedure must be demonstrated to remain clear of the HV “avoid” areas without requiring exceptional piloting skill or exceptionally favorable conditions.

(2) The hover reference height is es tablished as the minimum skid or wheel height above the takeoff surface from which a takeoff can consistently be accomplished in zero wind without contacting the runway surface. The takeoff must be accomplished with power fixed at the power required to hover at the hover reference height and must not require exceptional piloting skill to avoid runway surface contact.

AC 27.65. § 27.65 (Amendment 27-14) CLIMB: ALL ENGINES OPERATING.

a. Explanation .

(1) Rotorcraft other than helicopters.

(i) Section 27.65 requires that the steady rate of climb be determined for each rotorcraft other than helicopter with maximum continuous power on each engine for the range of weights, altitudes, and temperatures for which certification is requested.

Equivalent levels of safety have been found wherein the applicant was allowed to select a climb airspeed that was not the actual VY. The selected airspeed must be consistent with the speed used to show compliance with such items as cooling, stability, etc. The rate of climb resulting from the selected climb airspeed versus that from the actual VY shall not differ to an extent that a pilot will be encouraged, by appreciable increases in climb performance, to fly a climb airspeed different from that published in the flight manual.

(ii) For rotorcraft other than he licopters, the climb performance data obtained above must be used to show that a minimum climb gradient can be achieved for each weight, altitude, and temperature within the range for which certification is required. This gradient must be at least 1:10 if testing is done to determine the required takeoff distance over a 50-foot obstacle. If this option is selected, an explanation of the takeoff distance determination requirements and procedures may be found in paragraph AC 29.63 of AC 29-2C.

(iii) If takeoff distance is not det ermined, the minimum climb gradient must be 1:6 for standard sea level conditions.

(2) For helicopters, V Y must be determined for standard sea level conditions at maximum weight using maximum continuous power on each engine. Although not required, the steady rate of climb may be determined using the procedure in paragraph AC 27.65c of this section (Procedure to Determine All-Engine-Operating Climb Performance).

Page B - 26

(3) For helicopters, if V NE at any altitude is less than the maximum gross weight sea level standard day condition VY, the steady rate of climb must be determined at the climb speed(s) selected by the applicant not to exceed VNE. The climb performance must be determined from 2,000 feet below the altitude from where VNE intersects VY up to the maximum altitude for which certification is requested. This should be done utilizing maximum continuous power on each engine with the landing gear retracted.

b. Procedure to Determine V Y.

(1) Sawtooth climbs may be used to determine V Y. If such a technique is used, climbs should be flown in pairs on opposite headings 90° to the wind at the test altitude.

This procedure will minimize any windshear effects. All testing must be done in smooth air. Windshear is usually an indication of unstable air or a temperature inversion and must also be avoided. The climbs are flown on reciprocal headings for approximately 5 minutes or through an altitude band using maximum continuous power at a constant airspeed. Periodic power adjustments may be necessary. Additional reciprocal heading climbs must also be conducted at different airspeeds above and below the airspeed at the lowest point of the power required versus airspeed curve. This technique can be repeated at different altitudes to obtain VY throughout the altitude range.

(2) Level flight performance (speed pow er) may also be used to determine VY.

The testing should be done in smooth air. The advantage of this method is that less time is required, and the accuracy is equivalent to the sawtooth climb method. The test can be repeated at various altitudes to determine the VY throughout the altitude range desired for the rotorcraft. The test at each altitude should be conducted at a constant weight over sigma (W/σ). The test is normally started at the desired W/σ with maximum continuous power, or at VNE, in level flight. A series of points should be taken, reducing airspeed 10 to 15 knots between points, with the lowest speed point around 20 to 30 knots. Weight should be computed for each point and the test altitude adjusted to maintain a constant W/σ. After the data are reduced to standard day conditions, the minimum power required airspeed will be the VY speed.

(3) Prior to the flight test, the roto rcraft should be ballasted to the desired gross weight and the critical center of gravity. The airspeed should be stabilized prior to data acquisition. Data to be recorded includes time, altitude, airspeed, ambient temperature, engine parameters, torque(s), rotor RPM, fuel reading, aircraft heading, external configuration, etc. Power setting, weight, and climb airspeed should be planned prior to flight. For some turboshaft engines, temperature and/or engine speed limits may be reached prior to a limiting torque. The test team should verify that the resulting power utilized in these tests closely approximates the power producing capabilities of a minimum installed specification engine.

c. Procedure to Determine All-E ngine-Operating Climb Performance.

Page B - 27

(1) Background . Continuous climbs are conducted at the appropriate climb airspeeds as outlined above in order to validate the rotorcraft’s climb performance.

By-products are a qualitative evaluation of the rotorcraft handling characteristics in a climb and engine data to assist in the determination of installed power available.

(2) Techniques . The climbs are conducted on reciprocal headings at the established airspeed(s) through the target altitude range. The same parameters are recorded as during sawtooth climbs. The rotorcraft will usually climb very rapidly during the first few thousand feet; therefore, the data acquisition method must be timely if accurate results are expected. This procedure is usually repeated at weight extremes.

The resulting data must then be corrected for power and weight. Power and weight corrections are satisfactory, provided the test powers and weights closely approximate the target values to make the weight and power corrections small. Once this data is finalized and corrected for all the flight test variables, interpolation for intermediate weights can be made with a high degree of reliability. If the rotorcraft has any stability augmentation system, vent systems, etc., which may influence the climb performance, then it must be accounted for. Caution should be taken that anti-ice, air-conditioning, etc., are not on unless the performance is being established specifically for those conditions.

AC 27.65A. § 27.65 (Amendment 27-33) CLIMB: ALL ENGINES OPERATING.

a. Explanation . Amendment 27-33 added the requirement to determine the steady rate of climb, for helicopters, from sea level up to the maximum altitude for which certification is requested. Although not specifically stated in the rule, the rate of climb should be determined at VY or, if VNE at any altitude is less than the maximum gross weight sea level standard day condition VY, the steady rate of climb at these altitudes must be determined at a climb speed(s) selected by the applicant not to exceed VNE.

b. Procedures . The policy material pertaining to the procedures outlined in this section remain in effect.

AC 27.67. § 27.67 (Amendment 27-23) CLIMB: ONE ENGINE INOPERATIVE.

a. Explanation .

(1) Section 27.67 requires that for multiengine normal category rotorcraft, the steady rate of climb or descent with one engine inoperative must be determined at VY (or at the speed for minimum rate of descent) for maximum gross weight.

(2) The rate of climb (or descent) will be determined with the critical engine inoperative and the remaining engine(s) at maximum continuous or 30-minute minimum specification installed power available values. The landing gear should be retracted if it is retractable.

b. Procedures .

Page B - 28

(1) The procedure discussed in paragr aph AC 27.65 for all-engines-operating climb performance is also applicable to the OEI condition. For twin-engine rotorcraft that are shown not to have a “critical engine” with respect to performance characteristics, both engines may be used to simulate the appropriate single-engine power available during these tests.

(2) Adequate testing must be accomp lished to determine the rotorcraft’s OEI climb performance at maximum gross weight for all variations in altitude and temperature for inclusion in the Rotorcraft Flight Manual.

AC 27.71. § 27.71 (Amendment 27-21) GLIDE PERFORMANCE.

a. Explanation .

(1) Performance capabilities during st abilized autorotative descent are useful tools to assist the pilot when all engines fail. This information is also useful in determining the suitability of available landing areas along a given route segment.

(2) Two speeds are of particular impor tance, the speed for minimum rate of descent and the speed for best angle of glide. These speeds along with glide distance information are required as flight manual entries per § 27.1587. The speed for minimum rate of descent is useful for engine failure conditions at higher altitudes and the pilot is required to perform some time-related task, engine restart, float inflation, radio calls, etc.

The speed for best angle of glide is a somewhat higher speed that is of particular use when it is necessary to reach a distant landing area. These speeds, when utilized in conjunction with appropriate rotor RPM and glide angle (or rate of descent) can be used to calculate the maximum horizontal distance available from a particular altitude assuming zero wind conditions.

(3) A third speed, recommended autor otation speed, may be provided in addition to minimum rate of descent speed and maximum glide angle speed. The recommended speed for autorotation is usually optimized to assure an effective flare capability and yet be slow enough to allow a controlled, relatively slow touchdown condition. Recommended autorotation speed is ordinarily between the minimum rate of descent and maximum glide angle speeds. The recommended autorotation speed may be provided in the Rotorcraft Flight Manual. The relationship between minimum rate of descent, best glide angle, and recommended autorotation speed is shown in figure AC 27.71-1.

(4) Forward center of gravity is usua lly critical; however, center of gravity effects should be spot-checked to confirm this for a given design.

b. Procedures .

Page B - 29

(1) Tests are conducted at speeds which bracket the anticipated speeds for minimum rate of descent and best glide angle. On a power required plot, the speed for minimum power required approximates the speed for minimum rate of descent. The speed for maximum range glide may be estimated by drawing a tangent from the origin to the power required curve.

(2) Autorotative performance tests may be conducted in conjunction with the climb performance tests. The required data are similar for both tests and it is sometimes convenient and efficient to run alternating climbs and descents through a desired altitude band. Descents should be conducted on reciprocal headings and results averaged in the same manner as climb performance tests.

(3) A reduction in rotor RPM from the normal power-on value may enhance autorotative performance. If the applicant wishes to develop autorotative performance at RPM values significantly below the governing or power-on range, the practicality of reducing and controlling RPM at the lower value and of then increasing RPM as a landing is approached, must be considered. At low weights and low density altitudes, full down collective may automatically produce lower RPM values and this condition is, of course, acceptable provided the approved power-off RPM range is not exceeded.

(4) During autorotation tests, care must be taken to make certain that no engine power is delivered to the rotor drive system since a very small amount of power can have a large effect on descent performance.

Page B - 30