I€ 43.13-1A Page 9 972 10 д
NO FITTING WITHIN THESE LIMITS
- DIRECTION OF GRAIN IN - 1/28
PLYWOOD REINFORCEMENT
PLATES TO BE SAME AS ORIGINAL WEB.
PLYWOOD
A-SOLID WOOD FILLER BLOOKS
SECTION A-A FIGURE 1.6.-Repairs to built-up "I spar.
method of repair is essentially the same as in (A) except the plywood reinforcement plates on each side shown in solid black in section -C are continued, as in (C), the full distance between spars.
18. PLYWOOD SKIN REPAIR. Make extensive repairs to damaged stressed skin plywood structures in accordance with apecific recommendations from the manufacturer. It is recommended hat repairs be made by replacing the entire panel from one structural member to the hext, if damage is very extensive. When damaged plywood skin is repaired, carefully inspect the adjacent internal structure for possible hidden damage. Repair any defective frame members prior to making skin repairs.
a. Types of Patches. Four types of patcheshe surface or overlay patch, the splayed atch, the plug patch, and the scarf patch-are acceptable for repairing plywood skins. Surface patches should not be used on skins over 1/8 inch thick. Splayed patches should not be used on skins over 1/10 inch thick. There are no skin thickness limitations for the use of scarf patches and plug patches.
b. Determination of Single or Double Curvature, Much of the outside surface of plywood aircraft is curved. On such areas, plywood used for repairs to the skin must be similarly curved. Curved skins are either of single curvature or of double (compound) curvature. A simple test to determine which type of curvature exists may be made by laying a sheet of heavy paper on the surface in question. If the sheet can be made to fit the surface without wrinkling, the surface is either flat or has single curvature. If, however, the sheet cannot be made to fit the surface without wrinkling, the surface is of double curvature.
op 1 Par 17
Page 10 AC 43.13-1A 1972
ANGLE OF FACE GRAIN SAME AS IN ORIGINAL WEB
NEW WEB STAGGER WEB SPLICES (See Fig. 1.8 for method of splicing plywood webs).
• 10 B C
FOR CLARITY IOA - 6A- NEW WEB NOT INOLUDED IN THIS VIEW.
- SPRUCE REINFORCEMENT PLATES. A, 8,0, D = ORIGINAL DIMENSIONS.
FoURs 1.7.-Method of splicing box-spar flanges (plate method).
19. REPAIRS TO SINGLE CURVATURE PLYWOOD SKIN. Repairs to skins of single curvature may usually be formed from flat plywood, either by bending it dry or after soaking it in hot water.
The degree of curvature to which a piece of plywood can be bent will depend upon the direction of the grain and the thickness. Figure
1.12 is presented as a guide in determining which process of bending should be used for the curvature being considered. Plywood, after softening, may be bent on a cold ventilated form, or it may be bent over the leading edge near the part being patched if space permits.
In either method it should be allowed to dry completely on the form. When bending plywood over a leading edge, drying may be hastened by laying a piece of coarse burlap over the leading edge before using it as a bending form.
A fan to circulate the air over the bent piece will speed the drying. In bending pieces of small radii, or to speed up the bending of a large number of parts of the same curvature, it Par 19 may be necessary to use a heated bending form. The surface temperature of this form may be as high as 149° C. (800° F.), if necessary, without danger of damage to the ply.
wood. The plywood should be left on the form, however, only long enough to dry to room conditions.
20. REPAIRS TO DOUBLE CURVATURE PLYWOOD SKIN. The molded plywood necessary for a repair to a damaged plywood skin of double curvature cannot be made from flat plywood unless the area to be repaired is very small, or is of exceedingly slight double curvature; there fore, molded plywood of the proper curvature must be on hand before the repair can be made.
If molded plywood of the proper curvature is available, the repair may be made following the recommended procedures.
21. SPLAYED PATCH. Small holes with largest dimensions not over 15 times the skin thickness in skins not more than 1/10 inch in thickness Chop
AC 43.13-1A Pogo 11 972 JOAT
- INSERTED WEB SECTION 46- (1/6 FLANGE DEPTH)
PLYWOOD COVER STRIPS (Same thickness as "A").
FILLER BLOCKS I. AFTER INSERTED WEB HAS BEEN GLUED AND NAILED IN PLACE,GLUE AND NAIL COVER STRIP OVER ENTIRE LENGTH OF SPLICE JOINTS.
2. SECTIONAL SHAPE OF FILLER BLOCKS MUST CONFORM EXACTLY TO TAPER OF SPAR. THEY MUST NOT BE TOO TIGHTLY FITTED OR WEDGING ACTION WILL LOOSEN EXISTING GLUE JOINTS OF WEBS TO FLANGES. IF TOO LOOSELY FITTED, CRUSHING OF WEB WILL OCCUR WHEN CLAMPING.
SIRIT TO SAME AS ORIGINAL PLY OF NEW PLYWOOD WEB AND COVEF FIGURE 1.8.-Method of splicing box-spar webs.
Par 21
NO FITTING WITHIN THESE LIMITS 5 TO 1 SLOPE
- LONGITUDINAL CRACK
AND LOCAL DAMAGE SPRUCE BLOCKY
DIRECTION OF GRAIN IF
SPRUCE OR FAGE GRAIN IF PLYWOOD FIGURE 1.9.—Method of reinforcing a longitudinal crack and/or local damage in a solid or internally routed apar. AC 43.13-1A 1972
$3.1$- Page 13
• 12F RECOMMENDED -1 1OF MINIMUM
DAMAGED AREA GUSSET - ORIGINAL Y - 8
PLYWOOD- C==
SPRUCE OR
BASSWOOD AT A SPAR *4А† = C=
•Од- ЗА AT TRAILING EDGE -10 A A, B,O, D, E, F, 0 • ORIGINAL DIMENSIONS•
REINFORCEMENT PLATES
SHALL BE PLYWOOD GLUED AND NAILED.
AT A JOINT TO TRUSS MEMBERS THE DIRECTION OF THE
FACE GRAIN MUST BE
THE SAME AS ORIGINAL GUSSET.
T +3А→ - 10 A- FIGURE 1.10.-Repair of wood ribs.
ар 1 Par 21
Page 14 AC 43.13-1А 1972 SEE FIG. 1.10 FOR REPAIR OF CAPSTRIPS. , REPAIR DAMAGE-
SEE (D) (A) -ЗА - ЗА SEE FIG. 1.10 FOR REPAIR OF CAPSTRIPS. - REPAIR DAMAGE- (B) SEE FIG. 1.10 FOR REPAIR OF CAPSTRIPS. → REPAIR DAMAGE (G) * 12 A RECOMMENDED→
IOA MINIMUM 6 A- (D) А-А C-0
PLYWOOD
REINFORCEMENT E SAME THICKNESS AND FACE GRAIN DIRECTION AS ORIGINAL.
FIGURE 1.11.-Typical wing compression rib repairs.
Par 21 Chap 1
Ju r'ercent moisture content, Thoroughly soaked in hot water 1972 AC 43.13-1A bent on cold mandrels and bent on cold mandrels PLywood At 900 to At 0° or 450 At 900 to At 00 or 450 thickness face grain to face grain face grain to face grain ·→ (I) (2) (3) (4) (5) (6) Inch No. plies Inches Inches Inches Inches 3 0.5 0.1 3 105 ole 3 2.6 •8 3 3.8 1.2 3 5.3 1,8 3 761 2.6 5 17 6 2 5 21 7 3 5 27 10 4 5 31 20 12 5 5 43 28 16 7 5 54 36 21 10 Columns (1) and (3) may also be used for determining the maximun thickness of single laminations for curvel members.
FIGURE 1.12.—Minimum recommended bend radii for aircraft plywood.
may be repaired by using a circular splayed patch as illustrated in figure 1.18. The term "splayed" is used to denote that the edges of the patch are tapered, but the slope is steeper than is allowed in scarfing operations. The steps shown in figure 1.18 should be taken in making a splayed patch.
a. Lay out the patch according to figure 1.18.
Tack a small piece of plywood over the hole for a center point, and draw two circles, the inner one to be the size of the hole, and the outer one marking the limits of the taper. The difference between the radii is 5T (5 times the thickness of the skin). If one leg of the dividers has been sharpened to a chisel edge, the dividers may be used to cut the inner circle completely through.
b. Taper the hole evenly to the outer mark with a chisel, knife, or rasp.
c. Prepare a circular tapered patch to fit the prepared hole and glue the patch into place with face-grain direction matching that of the original surface.
d. Use waxed paper between the patch and a AC 43.13-1А 1972 plywood pressure plate cut to the exact size of the patch. This prevents extruded glue from binding patch and plate together. Center the plate carefully over the patch.
•. Apply pressure. As there is no reinforcement behind this patch, care must be used so that pressure is not great enough to crack the skin. On horizontal surfaces, weights or sandbags will be sufficient. On patches too far in for the use of standard hand clamps, jaws of greater length may be improvised.
f. Fill, sand, and refinish the patch.
22. SURFACE PATCH. Plywood skins that are damaged between or along framing members may be repaired by surface or overlay patches as shown in figure 1.14. Trim the damaged skin to a rectangular or triangular shape and round the corners. The radius of rounded corners should be at least 5 times the skin thicknesa. Cover surface patches with fabric before finishing. Fabric should overlap the original skin at least 2 inches. Surface patches located TRIM TO CIRCULAR SHAPE (15 T MAXIMUM DIAMETER. MINIMUM DISTANCE TO FRAME = 15 T.)
-FACE GRAIN OF PATCH PARALLEL TO FACE GRAIN OF SKIN.
INCH WEIGHTS OR CLAMP OR 1585 PRESSURE PLATE fOR "PLYWOOD
PAPER OR CELLOPHANE
- PLYWOOD SKIN FlOURe 1.18.-Splayed patch.
Par 21 Chap 1
AC 43.13-1A 11972 entirely aft of the 10 percent chordline, or which wrap around the leading edge and terminate aft of the 10 percent chordine are permissible. Bevel forward edges of patches located entirely aft of the 10 percent chordline to 4 times the skin thickness. Surface patches may have as much as a 50-inch perimeter and may cover as much as 1 frame (or rib) space.
The face-grain direction must be the same as the original skin.
23. SCARF PATCH. A properly prepared and inserted scarf patch is the best repair for damaged plywood skins and is preferred for most skin repairs. Figure 1.15 shows the details and dimensions to be used when installing typical scarf skin patches when the back of the skin is accessible. Follow figure 1.16 when the back of the skin is not accessible. The scarf slope of 1 in 12 shown in both figures is the steepest slope permitted for all species of plywood. If the radius of curvature of the skin at all points on the trimmed opening is greater than 100 times the skin thickness, a scarf patch may be installed.
Scarf cuts in plywood may be made by hand plane, spoke shave, scraper, or accurate sandpaper block, Rasped surfaces, except at the corners of scarf patches and sawed surfaces, are not recommended as they are likely to be rough or inaccurate.
Nail-strip gluing is often the only method avallable for gluing scarf joints in plywood when used in repair work; therefore, it is esential that all scarf joints in plywood be wacked with plywood or solid wood to provide adequate nailholding capacity. The face grain direction of the plywood patch should be the same as that of the original skin.
a. Scarf Patches (Back of Skin Accessible), When he back of a damaged plywood skin is accessible (such as a fuselage skin), it should be repaired with scarf patches following the details shown in figure 1.15. Whenever possible, the edge of the patch should be supported as shown in section C-C. When the damage folows or extends to a framing member, the carf may be supported as shown in section hap 1 Page 17 Damages that do not exceed 25 times the skin thickness in diameter after being trimmed to a circular shape, and if the trimmed opening is not nearer than 15 times the skin thickness to a framing member, may be repaired as shown in figure 1.15, section D-D. The backing block is carefully shaped from solid wood and fitted to the inside surface of the skin, and is temporarily held in place with nails. A hole, the exact size of the inside circle of the scarf patch, is made in the block, and is centered over the trimmed area of damage. The block is removed, after the glue on the patch has set, and leaves a flush surface to the repaired skin.
b. Steps in Making Scarf Patch (Back of Skin Not Accessible).
(1) After removing damaged sections, install backing strips, as shown in figure 1.16, along all edges that are not fully backed by a rib or a spar. To prevent warping of the skin, backing strips should be made of a soft-textured plywood, such as yellow poplar or spruce rather than solid wood. All junctions between backing atrips and ribs or spars should have the end of the backing strip supported by a saddle gusset of plywood.
(2) If needed, nail and glue the new gusset plate to rib. It may be necessary to remove and replace the old gusset plate by a new saddle gusset; or, it may be necessary to nail a saddle gusset over the original.
(3) Attach nailing strips to hold backing strips in place while the glue sets. Use bucking bar where necessary to provide support for nailing. Unlike the smaller patches made in a continuous process, work on the airplane must wait while the glue, holding the backing strips, sets. After setting, complete finishing in usual manner.
24. PLUG PATCHES. Two types of plug patches, oval and round, may be used on plywood sking provided the damage can be covered by the patches whose dimensions are given in figures
1.17 and 1.18. As the plug patch is strictly a skin repair, it should be used only for damage that does not involve the supporting structure under the skin. Oval patches must be prepared Far 12
Page 18 AC 43.13- JL _ JL
FRONT SPAR
•TRIMMED OPENING -MINIMUM RADIUS ST
- RIBS • DAMAGE →Д
SADDLE GUSSET -BEAB SPAR 30 т PATCHI -12 T-→ PLYWOOD SKIN (I" MINIMUM 8T ST It MIN PLYWOOD SADDLE GUSSET RIB CAP MINIMUM THICKNESS • T.
NAILED - GLUED IN PLACE.
SECTION A-A 12 T. - PATCH /ІГРАТОН *4T UNSUPPORTED -RIB. CAP LAP
SECTION B-B SECTION C-C FIGURE 1.14.-Surface patches.
Par 24 Chap
Saddle Gusset Hailing Strips Maximum Diameter 251 Minimum Distance 15T
• Temporary Backing 30T- Patch - 12T- Minimum Plywood Saddle Gusset Minlmum Thickness =T Nail-Glued in Place
SECTION A-A 12T ~ - Patch - 121--- - Patch Backing 31 Clamp and Glue Backing Clamp and Glue Backing to Frame and Skin Framing Member to Frame and Skin
SECTION B-B SECTION C-C
• Hailing Strips-
- 12T - 7 LEA Tomporary Backing Block Shape to fet Skir Cellophane or Paper
SECTION D-D FIGURE 1.15.-Scarf patches. back of akin accessible.
Per 24
Page 20 AC 43.1:
FRONT SPI SADDLE GUSSET+
REAR SPAR
• 30 T -12T- - PLYWOOD SKIN T 3T (· MINIMUM)- 8T (1" MINIMUM) RIb CAP
SECTION A - A PLYWOOD SADDLE GUSSET
PLYWOOD (MINIMUM THICKNESS SKIN- PATCH -12 T-.- PATCH RIB CAP • 3T "SPAR" PLYWOOD OR SPRUCE- (* MINIMUM)
PLYWOOD SKIN
SECTION B - B SECTION C-C FIGURE 1.16.-Scarf patches--back of akin not accessible.
Par 24 Chap