AC 90-114A

Change 1Historical

Advisory circular · Automatic Dependent Surveillance-Broadcast Operations

A newer version is currentThis is a historical version. AC 90-114C is the version in force, approved January 14, 2025.
Approved
March 7, 2016
Last reviewed
July 29, 2024
This change
Change 1 of AC 90-114A.
Cancels
AC90-114A
Cancelled by
AC90-114B
Family
AC 90-114 · 7 versions
Revision
A, change 1
14 CFR parts
91
14 CFR sections
§ 91.225§ 91.227

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 1–12

Par 4-3 Page 10 with the rule. Under part 21, installed equipment need not be manufactured under a TSO authorization, but must be approved or qualified according to the type of aircraft as follows:

(1) Type-Certificated Aircraft. ADS-B Out systems and equipment installed or used in type-certificated aircraft must have a design approval issued under part 21 or must be installed by field approval, if appropriate. The current edition of AC 20-165, Airworthiness Approval of Automatic Dependent Surveillance—Broadcast (ADS-B) Out Systems, provides guidance on installation of ADS-B Out systems. FAA Policy Memorandum, Installation Approval for ADS-B Out Systems, dated 2016, provides information on how ADS-B systems may be installed by field approval.

(2) Special Light-Sport Aircraft (S-LSA). Equipment installed on S-LSA must be installed in accordance with an applicable consensus standard and must be authorized by the aircraft's manufacturer or a person acceptable to the Federal Aviation Administration (FAA) (see § 21.181).

(3) Experimental Aircraft, Including Experimental Light-Sport Aircraft (E-LSA).

(a) For experimental category aircraft, including E-LSA, there is no FAA approval required for the ADS-B Out system installation. However, to protect all users of the National Airspace System (NAS), it is essential for all aircraft, including experimental and E-LSA, to install equipment that has been adequately designed and tested to meet the equipment’s intended functions of supporting safe air traffic control (ATC) separation services and providing accurate traffic awareness to other aircraft. To meet this requirement, owners of these aircraft may elect to install equipment manufactured under a TSO authorization, in accordance with the installation instructions provided by the manufacturer. Alternatively, owners of these aircraft may elect to install equipment that are not approved under a TSO authorization. For non-TSO equipment, the owner should obtain installation instructions that include a statement of compliance from the applicable avionics manufacturer(s). To qualify non-TSO equipment as compliant for operations in ADS-B airspace defined in § 91.225, the statement of compliance should indicate that when installed in accordance with the installation instructions, the equipment complies with all requirements of § 91.227, and with the performance requirements of the appropriate TSO. While the statement of compliance is important in equipping the aircraft, per § 91.225, correct installation is critical for the equipment to operate properly.

(b) Manufacturers of equipment intended for installation in experimental aircraft and E-LSAs are responsible to perform appropriate engineering efforts to determine that the equipment complies with all § 91.227 and TSO performance requirements before making their statement of compliance. The FAA will not approve or concur with manufacturers’ statements of compliance for this equipment. Manufacturers of this equipment should also consider the guidance in AC 20-165 when creating installation instructions. After making their statement of compliance, manufacturers of experimental aircraft and E-LSA equipment should be prepared to provide in-service product support to include design changes, equipment modifications (or instructions for performing them), and revisions to the installation, operating, and maintenance instructions.

Par 4-3 Page 11

(c) Owners of experimental aircraft should retain the installation instructions from the equipment supplier, including the statement of compliance, in the aircraft records to support the equipment’s compliance with the requirements of § 91.225 and § 91.227, and to assist in resolving in-service issues if necessary.

(4) All Aircraft—Importance of Proper Installation. Experience with FAA compliance monitoring of ADS-B Out-equipped aircraft to date has revealed that a large percentage of equipped aircraft have deficiencies with ADS-B Out system performance following initial installations. Many of these deficiencies have been attributed to improper installation and incorrect system configuration. Therefore, the FAA considers it particularly important for equipment manufacturers to provide installation instructions that are as clear and easy to follow as possible and revise these instructions when deficiencies in the instructions are discovered. Installers should adhere to the manufacturer’s installation instructions and employ practices that consistently result in ADS-B Out system installations that fully comply with § 91.227 equipment performance requirements.

(5) All Aircraft—Equipment Performance During Operation.

(a) If ADS-B Out performance becomes deficient during flight in § 91.225 airspace, ATC may require the aircraft to exit the airspace.

(b) The FAA continuously monitors compliance to the ADS-B Out equipment performance requirements. If FAA monitoring finds noncompliant equipment, aircraft with the noncompliant equipment installed may be denied access to § 91.225 airspace until the noncompliant equipment is corrected. This may require technical assistance from the applicable equipment manufacturers. Depending on the nature and scope of the noncompliance, the FAA may disqualify either an individual aircraft’s equipment (e.g., for improperly installed equipment on that specific aircraft), or all aircraft equipped with a certain type of equipment (e.g., for a design- or manufacturing-related equipment performance problem, or a problem traced to deficiencies with the installation, operating, or maintenance instructions, that may affect multiple aircraft).

(c) The FAA provides a service that enables aircraft owner/operators to verify compliance of ADS-B Out equipment performance requirements. Information on this service can be found at https://www.faa.gov/nextgen/equipadsb/. Owner/operators are encouraged to verify equipment performance through this service following installation, modification, or maintenance (to include component software updates) of ADS-B Out systems.

c. ATC-Authorized Deviations. Under § 91.225(g), operators must make requests for ATC-authorized deviations from the requirements in § 91.225 to the ATC facility that has jurisdiction over the concerned airspace or airport movement area within the time periods specified below:

Par 4-3 Page 12

(1) For operation of an aircraft with inoperative ADS-B equipment to the airport of ultimate destination (including any intermediate stops) to proceed to a place where suitable repairs can be made, or both, the request may be made at any time.

(2) For operation of an aircraft that is not equipped with ADS-B, operators must make the request at least 1 hour before the proposed operation.

4-4. FLIGHT PLANS (FP). When operating aircraft equipped with ADS-B, operators need to indicate their surveillance equipment code in field 10B of the U.S. Area Navigation (RNAV) and International Civil Aviation Organization (ICAO) FPs.

a. Transponder Codes. The transponder codes for ADS-B are as follows:

(1) E: Mode S, including Aircraft Identification (ACID), pressure-altitude, and Extended Squitter (ES) (ADS-B) capability.

(2) L: Mode S, including ACID, pressure-altitude, ES (ADS-B), and enhanced surveillance capability.

b. Surveillance Codes. The surveillance codes for ADS-B are as follows:

(1) B1: ADS-B with dedicated 1090 megahertz (MHz) ADS-B Out capability.

(2) B2: ADS-B with dedicated 1090 MHz ADS-B Out and In capability.

(3) U1: ADS-B Out capability using Universal Access Transceiver (UAT).

(4) U2: ADS-B Out and In capability using UAT.

c. ICAO FP Block 18 ADS-B Information.

(1) If ADS-B capability filed in item 10 is compliant with TSO-C166b, which is based on RTCA, Inc. DO-260B, include the item “SUR/260B.” If ADS-B capability filed in item 10 is compliant with TSO-C154c, which is compliant with RTCA DO-282B, include the item “SUR/282B.” If ADS-B capability filed in item 10 is not compliant with either TSO-C166b or TSO-C154c, include no “SUR/” information in this flight plan field.

(2) When ADS-B capability is filed in item 10, include CODE/Aircraft address expressed in the form of six hexadecimal characters (e.g., “CODE/HJF34B”).

NOTE: For a complete description of FP filing codes, including field 18, refer to the FAA Flight Planning Information Web site at http://www.faa.gov/about/office_org/headquarters_offices/ato/service_units/e nroute/flight_plan_filing.

Par 4-5 Page 13

4-5. PREFLIGHT REQUIREMENTS (U.S.-DESIGNATED AIRSPACE).

a. Flight Planning Requirements.

(1) Under § 91.103, pilots and operators must use all available information in planning their flight, to ensure that the performance requirements will be met for the duration of the flight.

Variations in position source performance affect ADS-B Out in two specific broadcast elements required by § 91.227—Navigation Accuracy Category for Position (NACp) and Navigation Integrity Category (NIC). During certain Global Positioning System (GPS) constellation geometries, some position sources may produce values for NACp and NIC that are less than required by the rule.

(2) Three different variants of GPS receivers are currently in use as a position source that can meet ADS-B Out rule performance requirements, to varying degrees, when adequate numbers of GPS satellites are in view. Selective Availability (SA) is a feature that deliberately degraded the GPS satellite signal, resulting in a less accurate reported position. SA was deactivated in 2000; however, SA-On GPS receivers assume SA is still active (on), thereby unnecessarily inflating integrity and accuracy bounds of the positions that are no longer degraded by SA. Most GPS receivers that are only compliant with TSO-C129 are SA-On receivers.

SA-Aware GPS receivers are designed to recognize that SA is inactive and optimize the performance from GPS. GPS receivers that comply with the performance requirements of TSO-C196 are SA-Aware receivers. Satellite Based Augmentation Systems (SBAS) receivers also use the additional signals from geostationary satellites specifically designed for aviation use, improving the quality and robustness of positioning performance. This difference in performance is most pronounced for very precise operations, such as Localizer Performance with Vertical Guidance (LPV) approaches, and for all operations when there are inoperative GPS satellites.

GPS receivers complying with TSO-C145 or TSO-C146 are SBAS receivers.

NOTE: Some GPS receivers manufactured with a TSO-C129a approval are SA-Aware, and, therefore, have the same NACp and NIC availability as TSO-C196() approved equipment. Operators should check with their GPS receiver supplier to verify whether their installed TSO-C129() GPS receiver is SA-On or SA-Aware.

NOTE: The wide area augmentation system (WAAS) is the designation of the SBAS system available in North America and is the term often used when making reference to SBAS in the United States.

b. ATC Authorization. It may be necessary for ATC to authorize operations in airspace for which ADS-B Out is required at times when the required performance cannot be met. During interference outages of GNSS (scheduled or unscheduled), the FAA may revert to alternate surveillance, as necessary, for affected areas. ATC will issue a Notice to Airmen (NOTAM) that authorizes such operations and identifies the airspace and time periods that the authorization is in effect. ATC will also issue a NOTAM to authorize performance outages when the FAA-provided preflight availability prediction tool is not available.

Par 4-5 Page 14

c. GPS Performance Prediction. Operators flying aircraft equipped with SBAS (TSO-C145 or TSO-C146) receivers do not need to conduct a preflight availability prediction because the FAA will issue a NOTAM whenever SBAS performance is not adequate. If TSO-C129() or TSO-C196() equipment is used for ADS-B Out, NACp and NIC availability prediction should be performed for the intended route of flight (route and time) using available GPS satellite information.

(1) Prediction Methods. Operators may use any of the following preflight availability prediction methods.

(a) Operators of large fleets of aircraft or users of flight planning programs may wish to use their own preflight availability verification tool. The operator is responsible for selecting a tool that accurately predicts the performance for their aircraft. The tool needs to account for the GPS satellites that are in service at the time of the prediction, and may take into account unique characteristics of the GNSS receiver, aircraft integration or installation; including performance better than required in FAA standards or use of inertial information integrated into the ADS-B Out position source. The FAA does not evaluate or approve a particular tool, but may evaluate the basis of the operator's determination that the tool is appropriate to their aircraft, particularly if its use results in noncompliant flights in airspace where ADS-B Out is required.

(b) Operators may use the FAA-provided preflight availability prediction tool, called the Service Availability Prediction Tool (SAPT) (http://sapt.faa.gov). Refer to the current edition of the SAPT User Guide for specific instructions on its use.

(c) Operators may use a third-party interface, incorporating FAA GPS performance prediction data without altering performance values, to predict NACp/NIC performance outages for the aircraft’s predicted flightpath and times.

(2) Prediction Model Parameters. The operator should use a model appropriate to their equipment, including the type of GPS receiver and the demonstrated capability to track satellites at a given mask angle. When selecting a mask angle, the operator should consider the equipment qualification, installation in the aircraft, and the effects of normal maneuvering.

Aircraft are typically qualified with a five degree mask angle, and operational experience has indicated that a two degree mask angle can be achieved by some equipment installations. If using the SAPT, each prediction is valid for the operation within 5 minutes of the plan time and

7.5 NM of the route. The operator may wish to submit additional requests for predictions for varying times around the proposed departure time to ensure compliance at the actual departure time.

(3) Flight Planning Guidance. Predictions can be used for initial flight planning as early as 72 hours prior to the planned departure. However, the operator should conduct a performance prediction as close to departure time as feasible, but with sufficient time to replan the flight or obtain ATC prior approval in the event a segment of the flight will not be compliant.

The prediction should be reevaluated prior to flight if a new NOTAM identifies an unscheduled GPS satellite outage.

Par 4-5 Page 15

(4) Resolving Predicted Outages in Performance. Except as provided in the following paragraph, in the event of a predicted loss of performance for any part of the intended flight in the airspace where ADS-B Out is required, the flight must be delayed, canceled, or rerouted to where the requirements can be met.

NOTE: Operators who do not hold FAA Exemption 12555 may request authorization to operate when their ADS-B preflight availability prediction is below the required values using the procedure described in subparagraph 4-3c.

d. NACp and NIC Performance Exemption. Some operators, using TSO-C129-compliant or TSO-C196-compliant GPS receivers for ADS-B Out, may obtain relief under FAA Exemption 12555 through December 31, 2024.

(1) Under the conditions of that exemption, operators with receivers meeting the performance requirements of TSO-C196() may operate in designated airspace for which ADS-B Out is required when the aircraft’s NACp and NIC do not meet the performance specified in the rule. For these operations, the operator does not need to conduct any preflight availability prediction.

(2) Operators conducting operations under Exemption 12555 using TSO-C129-approved GPS receivers that do not meet the performance requirements of TSO-C196, TSO-C145, or TSO-C146 may operate in airspace where ADS-B Out is required when the aircraft's NACp and NIC do not meet the performance specified in the rule, when the FAA determines that other surveillance is available. SAPT will indicate if the FAA has determined that surveillance is predicted to be available during a predicted performance outage.

This indication will not be applicable as an FAA authorization more than 2 hours before the planned departure time; preflight availability prediction requests submitted more than 2 hours in advance will be provided with an indication of whether the expected conditions will support the operation. Since the FAA must make the determination that alternate surveillance is predicted to be available, the SAPT is the only tool which can provide this capability. Operators may elect to use a combination of preflight availability prediction tools, to leverage a custom tool for normal flight planning and the SAPT for managing predicted outages under Exemption 12555.

NOTE: The FAA may change the criteria used to determine that surveillance is predicted to be available, considering the required ATC services (e.g., en route or terminal secondary surveillance radar, or primary radar).

4-6. FLIGHTCREW ENTRY OF REQUIRED ADS-B DATA. The operator must develop operational procedures to address flightcrew entry of the ADS-B message elements required in § 91.227 and as described in subparagraphs 4-6a through d. If the ADS-B avionics system design does not allow for a single point of entry for this information, the AFM, AFMS, RFM, RFMS, POH, or other required flight manual must address the requirement to enter the information multiple times through the appropriate system’s interface and to ensure that conflicting ACID information is not transmitted to ATC.

Par 4-6 Page 16

a. Mode A Code.

(1) ATC automation relies on the Mode A code to identify aircraft under radar surveillance and to correlate the displayed target to an FP. The Mode A code is one element of the transmitted ADS-B message set. Since SSR and ADS-B surveillance will overlap in much of the NAS, correlation of the Mode A code between the transponder and the ADS-B message is necessary to ensure that a single target is resolved and correlated to an FP route.

(2) It is imperative that the ATC-assigned transponder code is identical to the one in the ADS-B Out message. A preferable design configuration is one that provides the pilot a single point of entry for the Mode A code in both the transponder and the ADS-B Out avionics. If there is no single point of entry provided for the Mode A code into the transponder, then the AFM or operating handbook must address the requirement to enter the Mode A code into both systems separately.

NOTE: Transmission of conflicting transponder and ADS-B Mode A codes will result in erroneous traffic conflict alerts within the ATC automation system.

b. Aircraft’s Flight Identification (FLT ID).

(1) An aircraft’s FLT ID, also known as registration number or the operating company designator followed by the flight number (e.g., AAL3342), is transmitted by the ADS-B Out avionics. The FLT ID is comprised of a maximum of seven alphanumeric characters and also corresponds to the ACID annotated on the ATC FP. The FLT ID is typically entered by the flightcrew during preflight through either a flight management system (FMS) interface (control display unit (CDU)) or transponder control panel (CP). The FLT ID for General Aviation (GA) aircraft is associated with the aircraft’s registration number. The aircraft owner can preset the FLT ID to the aircraft’s registration number (e.g., N235RA), since it is a fixed value, or the pilot can enter it into the ADS-B Out system prior to flight.

(2) Some ATC systems use transmitted FLT IDs to uniquely identify each aircraft within a given airspace and correlate them with a filed FP for the provision of surveillance and separation services. If the FLT ID is not entered correctly, ATC automation systems may not associate surveillance tracks for the aircraft to its filed FP. Therefore, air traffic services may be delayed or unavailable until this is corrected. Consequently, it is imperative that flightcrews and GA pilots ensure the FLT ID entry correctly matches the ACID annotated in the filed ATC FP prior to departure.

(3) For operations using variable call signs (e.g., Lifeguard), the operator should verify with equipment manufacturers that this capability is available in the avionics and should obtain guidance for the proper procedures to enter variable call sign codes.

c. Emergency Status.

(1) This ADS-B message element and transponder code alerts ATC that the aircraft is experiencing emergency conditions and indicates the type of emergency. The appropriate emergency code should be entered into the transponder (e.g., 7500, 7600, and 7700). The ICAO

Par 4-6 Page 17 (and 18) Annex 10, Volume IV, Surveillance Radar and Collision Avoidance Systems, emergency codes (general emergency, no communications, and unlawful interference) are required by § 91.227.

(2) ADS-B systems integrated within a transponder will automatically set the applicable emergency status when code 7500, 7600, or 7700 is entered into the transponder.

(3) ADS-B systems not integrated with the transponder or systems with optional emergency codes may require the appropriate emergency code to be entered through a separate pilot interface. Flightcrews must ensure that both emergency codes (ADS-B and transponder) are identical.

d. Transponder IDENT Function. The required AFM or POH will provide specific instructions on how the IDENT feature will be activated in specific installations, including any installations with multiple IDENT features.

Page 21 · 1Open in PDF

Appendix 1 APPENDIX 1. ADS-B OUT OPERATIONS OUTSIDE OF U.S.-DESIGNATED

AIRSPACE

1. PURPOSE. This appendix provides a description of the Automatic Dependent Surveillance-Broadcast (ADS-B) operations outside of U.S.-designated airspace and guidance to operators seeking Federal Aviation Administration (FAA) authorization to conduct ADS-B operations outside of U.S.-designated airspace.

2. BACKGROUND. Countries around the world are implementing ADS-B technology to enhance or extend the surveillance capability of their air traffic control (ATC) systems.

A number of these countries have published new rules that will mandate ADS-B equipage on aircraft operating in certain classes of airspace. Other countries have chosen not to mandate ADS-B equipage, but have designated specific routes and airspace to benefit those who equip voluntarily. A certain subset of these countries further requires that foreign operators obtain operational approval from their State of Registry to access ADS-B airspace. Where U.S. aircraft operators are seeking access to foreign ADS-B airspace where State of Registry operational approval is required, FAA has established a process for obtaining such approval.

3. APPLICABILITY. The following identifies just some of the foreign flight information regions (FIR) where U.S. aircraft operators are required by the cognizant State regulator to have ADS-B Out operational approval. It is provided for administrative planning purposes only. Refer to relevant FIR documentation for the most accurate information.

a. Australia. Operations Specification (OpSpec)/Management Specification (MSpec)/Letter of Authorization (LOA) A153, Automatic Dependent Surveillance-Broadcast (ADS-B) Out Operations Outside of U.S.-Designated Airspace, is not required. Approved ADS-B avionics will be required, for all operations at or above flight level (FL) 290. (Refer to the current edition of Australian Civil Aviation Safety Authority (CASA) Advisory Circular (AC) 21-45, Airworthiness Approval of Airborne Automatic Dependent Surveillance-Broadcast Equipment.

b. Canada. OpSpec/MSpec/LOA A153 is not required. Approved ADS-B avionics will be required when an operator seeks operational benefit from ADS-B Out equipage in the airspace defined in NavCanada, Aeronautical Information Publication (AIP) Canada, Part 2—En Route (ENR), Section 1.6.3, Automatic Dependent Surveillance-Broadcast.

c. China (Sanya). Authorization, per OpSpec/MSpec/LOA A153, is required. A153 is required for all U.S. aircraft operators flying over performance-based navigation routes L642 or M771 at or above FL290 within the Sanya FIR.

d. China (Taipei). Authorization, per OpSpec/MSpec/LOA A153, is required. A153 is required for all U.S.-registered aircraft flying over routes B576 or B591 at or above FL290 within the Taipei FIR. For additional information regarding ADS-B operations within the Taipei FIR, refer to Republic of China Civil Aeronautics Administration AIP Supplement (AIP SUP) 08/14, Revision to Automatic Dependent Surveillance-Broadcast (ADS-B) Out Operation Within Taipei FIR.

Page 22 · 2Open in PDF

Appendix 1

e. Europe. OpSpec/MSpec/LOA A153 is not required. Surveillance requirements within the European air traffic management network (EATMN) as well as the upcoming implementation dates are provided in Commission Implementing Regulation (EU) No. 1207/2011, amended by Commission Implementing Regulation (EU) No. 1028/2014.

However, an amendment to the current regulation has been endorsed, which proposes a change in the existing implementation dates.

f. Fiji. OpSpec/MSpec/LOA A153 is not required. Fiji has mandated ADS-B equipage only for Fiji-registered aircraft operating in controlled airspace. For additional information regarding ADS-B operations, refer to the current editions of the Civil Aviation Authority of the Fiji Islands (CAAFI) Air Navigation Regulations 1981 and Fiji AIC 04/11, Operation of Foreign Registered Aircraft in Fiji.

g. Hong Kong. OpSpec/MSpec/LOA A153 is required. Authorization, per A153, is required for all U.S. aircraft operators flying over performance-based navigation routes L642 or M771 at or above FL290 within the Hong Kong FIR. Additionally, A153 will be required for all U.S. aircraft flying within the entire Hong Kong FIR at or above FL290. For further information regarding ADS-B operations within the Hong Kong FIR, refer to the current edition of the Hong Kong AIP.

h. India. OpSpec/MSpec/LOA A153 is required for ADS-B Out services. ADS-B Out implementation in India is aimed at providing redundancy where radar surveillance is already available. In addition, ADS-B Out enables the expansion of ATC surveillance services in remote and high terrain areas, oceanic airspace, and also to fill any surveillance gaps over continental India. For additional information regarding ADS-B operations, refer to India Aeronautical Information Regulation and Control (AIRAC) AIP SUP 18/2014, Automatic Dependent Surveillance-Broadcast (ADS-B) Out Based ATS Surveillance Services.

i. Republic of Indonesia. OpSpec/MSpec/LOA A153 is not required. Indonesia has established mandatory aircraft fitment of ADS-B avionics equipment for the operation of any aircraft in Indonesian airspace at or above FL290 after the compliance date of December 31, 2017. Until that date, carriage of ADS-B equipment remains voluntary, though ATC will give preference to ADS-B-equipped aircraft in areas of ADS-B Only surveillance coverage. For additional information, refer to Republic of Indonesia AIRAC AIP SUP 08/15, Automatic Dependent Surveillance-Broadcast (ADS-B) Implementation in Indonesia for ATS Surveillance Separation (Tier – 1).

j. Republic of Seychelles. OpSpec/MSpec/LOA A153 is not required. Approved ADS-B Out equipment will be required in all controlled airspace. For additional information regarding ADS-B operations, refer to Republic of Seychelles AIC 02/2014, Mandatory Carriage of GNSS Navigation Equipment, ADS-B and Mode S Transponders in SEYCHELLES Airspace.

k. Singapore. OpSpec/MSpec/LOA A153 is not required. ADS-B is used to provide ATC separation on ATS routes N891, M753, L642, M771, L644, and N892 at FL290 and above within the Singapore FIR. For additional information, refer to the current edition of the Civil Aviation Authority of Singapore (CAAS) AIP.

Page 23 · 3Open in PDF

Appendix 1

l. Vietnam. Authorization, per OpSpec/MSpec/LOA A153, is required. A153 is required for all U.S.-registered aircraft flying over ATS routes L625, M771, N892, L642, M765, M768, N500, and L628 at or above FL290 within the Ho Chi Minh FIR. For additional information regarding ADS-B operations within the Ho Chi Minh FIR, refer to Civil Aviation Authority (CAA) of Vietnam AIC 03/13, Implementation of ADS-B within Ho Chi Minh FIR.

m. Additional Regions. As additional regions are implementing ADS-B, U.S. aircraft operators are advised to monitor the regions applicable to their operation for any changes related to ADS-B requirements and to comply with Title 14 of the Code of Federal Regulations (14 CFR) part 91, § 91.703. Normally, these types of advisories are transmitted through State AIPs and/or AICs.

4. AUTHORIZATION TO CONDUCT ADS-B OPERATIONS OUTSIDE OF U.S.-DESIGNATED AIRSPACE WHERE STATE OF REGISTRY OPERATIONAL APPROVAL IS REQUIRED. FAA authorization is required for all U.S. aircraft operators seeking access to foreign ADS-B airspace where State of Registry operational approval is required. This appendix provides guidance to operators on the process and documentation required when requesting issuance of this authorization.

NOTE: For FAA authorization, refer to FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 3, Chapter 18, Section 3, OpSpec/MSpec/LOA A153.

a. Initial Request for Authorization. U.S. aircraft operators seeking to conduct ADS-B Out operations outside of U.S.-designated airspace need to first contact their assigned FAA office to indicate their intent. At the time of the operator’s initial request, the FAA will provide the operator with an OpSpec/MSpec/LOA A153 Application Checklist (found in the A153 guidance section of the Web-based Operations Safety System (WebOPSS) or at http://www.faa.gov/nextgen/programs/adsb/ under Quick Links), which must be completed and included with attached support documents when submitting a formal request for authorization.

b. Required Documentation for Submission of Formal Request.

(1) Documentation Guidance. The following paragraph provides general guidance on the documentation required for submission of a formal request for issuance of this authorization.

At the discretion of the operator’s assigned principal inspector (PI), additional information may be required based on any unique aspects of specific operations. The operator must submit a letter of request for issuance of authorization to the assigned PI. The letter of request should include the following information:

(a) Type of aircraft (make, model, and series (M/M/S)).

(b) Airplane registration number(s) and serial number(s).

(c) Areas of intended operation.

Page 24 · 4Open in PDF

Appendix 1 NOTE: The guidance contained in subparagraph 4b of this appendix will also be annotated on the OpSpec/MSpec/LOA A153 Application Checklist provided to the operator by the applicable FAA field office.

(2) Airplane Flight Manual (AFM) Compliance Documentation. The operator will provide a copy of the AFM, Aircraft/Airplane Flight Manual Supplement (AFMS), Airplane Operations Manual (AOM), or pilot’s operating handbook (POH), as appropriate, which states that the aircraft’s ADS-B Out system complies with any of the following:

(a) Section 91.227.

(b) The current edition of AC 20-165, Airworthiness Approval of Automatic Dependent Surveillance Broadcast (ADS-B) Out Systems.

(c) European Aviation Safety Agency (EASA) Acceptable Means of Compliance (AMC) 20-24, Certification Considerations for the Enhanced ATS in Non-Radar Areas using ADS-B Surveillance (ADS-B-NRA) Application via 1090 MHz Extended Squitter, (until rescinded) or Certification Specifications and Acceptable Means of Compliance for Airborne Communications, Navigation and Surveillance (CS-ACNS).

NOTE: The following is an example of an AFM statement for an ADS-B system that complies with § 91.227: “The installed ADS-B Out system has been shown to meet the equipment requirements of 14 CFR § 91.227.”

NOTE: ADS-B Out systems approved per previous versions of AC 20-165 must have any variances, with subsequent revisions of that guidance, resolved through the FAA/manufacturer issue paper process. Such systems do not require revision of existing AFM, AFMS, AOM, POH, Flight Operations Manual (FOM), or equivalent AC 20-165 compliance statements.

NOTE: The requirements in this appendix meet all of the operational, training, and maintenance considerations of AMC 20-24.

(3) Proposed Operations Area. A copy of OpSpec/MSpec B050, Authorized Areas of En Route Operation, Limitations, and Provisions, annotating the authorized en route areas where OpSpec/MSpec/LOA A153 will be used (not applicable to part 91 operators).

(4) Part 91 Operators. A statement that the operator’s pilots have knowledge of current air traffic ADS-B directives for the intended areas of en route operation and will comply with § 91.703.

(5) OpSpec/MSpec/LOA A153. A copy of the completed OpSpec/MSpec/LOA A153, as applicable.

NOTE: The local Flight Standards Service (AFS) field office will conduct a review of the applicant’s submitted proposal using the OpSpec/MSpec/LOA A153 Application Checklist. When compliance with all applicable requirements has been demonstrated, the PI will issue A153.