Par 2-1 Page 3 CHAPTER 2. OVERVIEW AND SYSTEM DESCRIPTION
2-1. OVERVIEW. Starting with the National Airspace System (NAS)-wide implementation of Automatic Dependent Surveillance-Broadcast (ADS-B), the Federal Aviation Administration (FAA) has begun to facilitate improvements needed to increase the capacity and efficiency of the NAS while maintaining safety. ADS-B supports these improvements by providing a higher update rate and enhanced accuracy of surveillance information over the current radar-based surveillance systems. In addition, ADS-B enables the expansion of air traffic control (ATC) surveillance services into areas where none existed previously. The ADS-B ground system also provides Traffic Information Services-Broadcast (TIS-B) and Flight Information Service-Broadcast (FIS-B) for use on appropriately equipped aircraft, enhancing the user’s situational awareness (SA) and improving the overall safety of the NAS.
2-2. ADS-B SYSTEM DESCRIPTION.
a. ADS-B System Architecture. The ADS-B system architecture is composed of aircraft avionics and a ground infrastructure. Onboard avionics determine the position of the aircraft, typically by using the Global Navigation Satellite Systems (GNSS) and transmitting this and additional information about the aircraft to ground stations for use by ATC, to ADS-B-equipped aircraft, and to other aviation service providers.
b. ADS-B Operating Frequencies. In the United States, the ADS-B system operates on two frequencies: 1090 or 978 megahertz (MHz). See Chapter 3, Figure 3-1, Automatic Dependent Surveillance-Broadcast Airspace Rule (§ 91.225) Diagram, for airspace and frequency requirements.
(1) The 1090 MHz Frequency. The 1090 MHz frequency is associated with current Mode A, C, and S transponder operations. ADS-B information is included in Mode S transponders’ Extended Squitter (ES) transmit messages, and referred to as 1090ES in this AC.
(2) The 978 MHz Frequency. ADS-B equipment operating on 978 MHz are referred to as Universal Access Transceivers (UAT) in this AC.
c. ADS-B Avionics Operating Modes. ADS-B avionics can have the ability to both transmit and receive information.
(1) ADS-B Out. The transmission of ADS-B information from aircraft is known as ADS-B Out.
(2) ADS-B In. The receipt of ADS-B information by an aircraft is known as ADS-B In.
NOTE: After January 1, 2020, all aircraft operating within the airspace defined in Title 14 of the Code of Federal Regulations (14 CFR) part 91, § 91.225 will be required to transmit (ADS-B Out) the information defined in § 91.227 using Technical Standard Order (TSO)-C166b, Extended Squitter Automatic Dependent Surveillance-Broadcast (ADS-B) and Traffic Information Service-Broadcast (TIS-B) Equipment Operating on Radio Frequency of 1090 Megahertz (MHz), or TSO-C154c, Universal Access
Par 2-2 Page 4 Transceiver (UAT) Automatic Dependent Surveillance-Broadcast (ADS-B) Equipment Operating on Frequency of 978 MHz, avionics.
2-3. ADS-B BROADCAST SERVICES. ADS-B implementation includes three broadcast services: Automatic Dependent Surveillance-Rebroadcast (ADS-R), TIS-B, and FIS-B.
a. ADS-R. Because the ADS-B system operates on two separate frequencies (1090 MHz and 978 MHz), there is a need to translate, reformat, and rebroadcast the information from each frequency to enable aircraft operating on the other frequency to process and use the other’s information. This process is referred to as ADS-R and occurs within the ADS-B ground station.
NOTE: Aircraft operating on the same ADS-B frequency exchange information directly and do not require ADS-R translation. Aircraft with ADS-B In capability on both UAT and 1090ES do not require ADS-R service.
b. TIS-B. TIS-B is the broadcast of transponder-based mode C or mode S traffic information derived from ATC surveillance systems. TIS-B provides ADS-B In-equipped aircraft with a more complete picture of surrounding traffic in situations where not all aircraft are equipped with ADS-B.
c. FIS-B. The FIS-B operates on UAT only and provides ADS-B In-equipped aircraft with a suite of advisory-only aeronautical and weather information products to enhance the user’s SA.
Additional information on FIS-B and the products available through the service are provided in the Aeronautical Information Manual (AIM) and the current edition of Advisory Circular (AC) 00-63, Use of Cockpit Displays of Digital Weather and Aeronautical Information.
2-4. USE OF ADS-B IN INFORMATION FOR TRAFFIC SA. This paragraph provides guidance on the use of ADS-B In information for traffic SA. See the appropriate appendices of this AC for guidance on the use of ADS-B In for the more advanced procedures that require FAA authorization. Installation of ADS-B In equipment is not required for compliance with § 91.225 or § 91.227. However, aircraft owners and operators who choose to voluntarily equip with ADS-B In avionics will achieve greater benefit from the technology through improved traffic SA on the ground and in the air.
NOTE: This AC only addresses ADS-B In systems installed in compliance with the current edition of AC 20-172, Airworthiness Approval for ADS-B In Systems and Applications, and meeting the equipment requirements of TSO-C195a (or later revision), Avionics Supporting Automatic Dependent Surveillance-Broadcast (ADS-B) Aircraft Surveillance Applications (ASA).
a. ADS-B In Systems. Most ADS-B In systems will include a flight deck traffic display depicting the relative position and related information of ADS-B-equipped aircraft presented on a plan view. This traffic display is only one component of the input and output devices collectively known as a Cockpit Display of Traffic Information (CDTI). The traffic display may be on a dedicated display or integrated into and presented on an existing display (e.g., navigation display (ND) or multifunction display (MFD)). The terms traffic display and CDTI are used interchangeably when the meaning is clear in context. In many installations, a moving map
Par 2-4 Page 5 depicting key surface elements of the airport may be displayed when on the ground or within a predefined altitude/distance from an airport while airborne.
NOTE: Airborne Traffic Advisory System (ATAS) is an ADS-B In application intended specifically for General Aviation (GA) use that will incorporate an audio traffic alerting capability. There is a configuration in which the display is optional for aircraft that cannot accommodate a display.
b. Operation. The CDTI will display nearby ADS-B Out traffic and may also display TIS-B traffic, depending on the installation and operating airspace. The display may have functionality to allow the pilot to select a target to obtain additional information that might not be automatically displayed, such as distance from own-ship and groundspeed (GS). The system will also provide range selection and declutter functionality. More advanced ADS-B In systems may also include certified functionality to perform ADS-B In procedures described in the appendices of this AC.
NOTE: For traffic SA, pilots are encouraged to incorporate the display in their normal scan to aid in the early detection of nearby traffic when in visual conditions and to aid in understanding the flow and amount of nearby traffic when in instrument conditions. However, the traffic display is not intended to be used for self-separation or to deviate from an ATC clearance.
Should questions arise about a potential conflict with traffic while on an instrument flight rules (IFR) clearance, the pilot should query ATC. Pilots are also cautioned to not allow the display to become a distraction from the primary task of flying the aircraft. Finally, pilots are cautioned against unnecessarily communicating on the ATC frequency about traffic observed on the traffic display.
c. Limitations. Pilots should understand the proper use and limitations of their equipment and adhere to the following:
(1) Only use the traffic display to supplement what can be seen out the window (OTW), except when authorized to conduct ADS-B In operations described in the appendices of this AC.
Pilots must always conduct OTW scans to see and avoid as required under § 91.113(b).
(2) Unless specifically certified for the function, the traffic display is not intended for collision avoidance or self-separation.
(3) Not all ground and airborne traffic will appear on the traffic display. Only properly equipped ADS-B Out traffic broadcasting on the ADS-B frequency(ies) being received and processed by the onboard avionics will appear. The traffic display can only display properly equipped ADS-B Out traffic broadcasting on the same frequency, and, depending on the equipment installation and operating airspace, ADS-R, TIS-B, and/or Traffic Alert and Collision Avoidance System (TCAS) (if installed) traffic. Additionally, the completeness of the traffic SA information is affected by range, signal quality, and proper installation and function of the ADS-B Out system on the traffic aircraft.
Par 2-4 Page 6
(4) Unless initiated by the controller, pilots should typically not use the call sign or ACID of observed traffic in radio communications, as this could create confusion for both ATC and pilots monitoring the frequency.
(5) In multipiloted aircraft, establish and comply with crew coordination procedures on the use of the CDTI and ADS-B In information to minimize head-down time.
(6) Use of the traffic display does not change pilot or controller responsibilities.
(7) If at any time the presented information becomes unreliable, inoperative, or a distraction, disregard the information presented on the traffic display.
(8) In TCAS-equipped aircraft, ADS-B In traffic display information does not replace guidance from a traffic advisory (TA) and/or Resolution Advisory (RA). RA response needs to be based on the TCAS system guidance and following approved procedures.
Par 3-1 Page 7 CHAPTER 3. OPERATIONAL CONSIDERATIONS
3-1. U.S. AUTOMATIC DEPENDENT SURVEILLANCE-BROADCAST (ADS-B) AIRSPACE AND EQUIPMENT PERFORMANCE REQUIREMENTS. After January 1, 2020, unless authorized by air traffic control (ATC), all aircraft operating in the airspace specified in Title 14 of the Code of Federal Regulations (14 CFR) part 91, § 91.225 must meet the equipment performance requirements defined in § 91.227. This chapter describes both the airspace and equipment performance requirements of §§ 91.225 and 91.227. Operators should consider the need to access ADS-B-required airspace and the performance requirements of that airspace when equipping for compliance with §§ 91.225 and 91.227.
a. Inside Class A Airspace. Operations in Class A airspace must:
(1) Meet the equipment performance requirements in Technical Standard Order (TSO)-C166b, Extended Squitter Automatic Dependent Surveillance-Broadcast (ADS-B) and Traffic Information Service-Broadcast (TIS-B) Equipment Operating on Radio Frequency of 1090 Megahertz (MHz) (1090ES).
(2) Meet the requirements of § 91.227.
NOTE: Although TSO-C166b incorporates standards for TIS-B equipment, TIS-B equipage (ADS-B In) is not required for compliance with §§ 91.225 and 91.227.
b. Outside Class A Airspace. Operations outside Class A airspace must:
(1) Meet the requirements of § 91.227;
(2) Meet the performance requirements in TSO-C166b (1090ES); or
(3) Meet the performance requirements in TSO-C154c, Universal Access Transceiver (UAT) Automatic Dependent Surveillance-Broadcast (ADS-B) Equipment Operating on Frequency of 978 MHz, in the following airspace:
(a) Class B and Class C airspace.
(b) Except as provided for in § 91.225(e), within 30 nautical miles (NM) of an airport listed in part 91 appendix D (Mode C veil), section 1, from the surface upward to 10,000 feet mean sea level (MSL).
(c) Above the ceiling and within the lateral boundaries of a Class B or Class C airspace designated for an airport upward to 10,000 feet MSL.
(d) Except as provided for in § 91.225(e), Class E airspace within the 48 contiguous United States and the District of Columbia at and above 10,000 feet MSL, excluding the airspace at and below 2,500 feet above the surface (i.e., mountainous areas).
Par 3-1 Page 8
(e) Class E airspace at and above 3,000 feet MSL over the Gulf of Mexico, from the coastline of the United States out to 12 NM.
FIGURE 3-1. AUTOMATIC DEPENDENT SURVEILLANCE-BROADCAST AIRSPACE RULE (§ 91.225) DIAGRAM
3-2. EXCEPTIONS TO AIRSPACE REQUIREMENTS. The requirements of § 91.225(b) do not apply to any aircraft that was not originally certified with an electrical system or that has not subsequently been certified with such a system installed, including balloons and gliders.
These aircraft may conduct operations without ADS-B Out in the airspace specified in § 91.225(d)(2) and (4). However, for other aircraft without ADS-B Out, § 91.225(g) requires ATC authorization prior to operation in ADS-B Out-required airspace. Note that when the Federal Aviation Administration (FAA) issues an experimental or special airworthiness certificate to aircraft with an electrical system, that electrical system is considered certified and thus the exception to § 91.225 described above does not apply.
Par 4-1 Page 9 CHAPTER 4. OPERATING PROCEDURES
4-1. GENERAL OPERATING PROCEDURES. This chapter describes the general procedures for Automatic Dependent Surveillance-Broadcast (ADS-B) Out operations in accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 91, § 91.225. All operators should use this information when planning and conducting operations requiring ADS-B Out performance.
4-2. OPERATOR FAMILIARITY OF THE INSTALLED ADS-B SYSTEM.
a. System Operation Familiarity. All operators should use the applicable Airplane Flight Manual (AFM), Aircraft/Airplane Flight Manual Supplement (AFMS), Rotorcraft Flight Manual (RFM), Rotorcraft Flight Manual Supplement (RFMS), pilot’s operating handbook (POH), or other required operating handbooks or manuals to become familiar with the proper operation of the installed ADS-B system and any procedures expected of the user for indications of reduced performance or failures within the system.
b. Understanding Failure Indicators within the System. Because many ADS-B system installations will be upgrades to existing transponders (Mode S), there may be limited ability to indicate ADS-B failures. Mode S transponders with ADS-B functionality may indicate a device failure (loss of transponder/ADS-B) and input failures (loss of position source, such as the Global Navigation Satellite System (GNSS)) with the same indicator light. Operators should refer to their AFM, AFMS, RFM, RFMS, POH, and other handbooks and manuals for information on the differences between device failures and function failures and the implications and procedures associated with each failure type.
c. Transponder Operation and ADS-B Transmissions. For ADS-B system installations integrated within a transponder that share control features, operators should be aware that disabling the transponder may also disable ADS-B transmissions, as well as result in a loss of Secondary Surveillance Radar (SSR) services and Traffic Alert and Collision Avoidance System (TCAS)/TCAS II operation, if so equipped.
4-3. ADS-B EQUIPMENT OPERATIONS (U.S.-DESIGNATED AIRSPACE).
a. Transmit Requirements. In accordance with § 91.225(f), each person operating an aircraft equipped with ADS-B Out must operate this equipment in the transmit mode at all times.
This equipment operation requirement pertains to all phases of flight operation, including airport surface movement area operations. Under 14 CFR part 21, § 21.31, for ADS-B installations integrated within a transponder, the flight manual, checklists, and any operator’s procedures manuals must be updated accordingly with proper ADS-B system operations guidance.
NOTE: Aircraft must comply with the appropriate Technical Standard Order (TSO) performance requirements when transmitting ADS-B data.
b. Equipment Qualification Requirements. In order to operate an aircraft in airspace defined in § 91.225, the ADS-B Out equipment installed must meet the performance requirements of the applicable ADS-B TSOs and meet the requirements of § 91.227. Since § 91.225 requires the equipment to be installed, portable ADS-B Out equipment does not comply
Par 4-3 Page 10 with the rule. Under part 21, installed equipment need not be manufactured under a TSO authorization, but must be approved or qualified according to the type of aircraft as follows:
(1) Type-Certificated Aircraft. ADS-B Out systems and equipment installed or used in type-certificated aircraft must have a design approval issued under part 21 or must be installed by field approval, if appropriate. The current edition of AC 20-165, Airworthiness Approval of Automatic Dependent Surveillance—Broadcast (ADS-B) Out Systems, provides guidance on installation of ADS-B Out systems. FAA Policy Memorandum, Installation Approval for ADS-B Out Systems, dated 2016, provides information on how ADS-B systems may be installed by field approval.
(2) Special Light-Sport Aircraft (S-LSA). Equipment installed on S-LSA must be installed in accordance with an applicable consensus standard and must be authorized by the aircraft's manufacturer or a person acceptable to the Federal Aviation Administration (FAA) (see § 21.181).
(3) Experimental Aircraft, Including Experimental Light-Sport Aircraft (E-LSA).
(a) For experimental category aircraft, including E-LSA, there is no FAA approval required for the ADS-B Out system installation. However, to protect all users of the National Airspace System (NAS), it is essential for all aircraft, including experimental and E-LSA, to install equipment that has been adequately designed and tested to meet the equipment’s intended functions of supporting safe air traffic control (ATC) separation services and providing accurate traffic awareness to other aircraft. To meet this requirement, owners of these aircraft may elect to install equipment manufactured under a TSO authorization, in accordance with the installation instructions provided by the manufacturer. Alternatively, owners of these aircraft may elect to install equipment that are not approved under a TSO authorization. For non-TSO equipment, the owner should obtain installation instructions that include a statement of compliance from the applicable avionics manufacturer(s). To qualify non-TSO equipment as compliant for operations in ADS-B airspace defined in § 91.225, the statement of compliance should indicate that when installed in accordance with the installation instructions, the equipment complies with all requirements of § 91.227, and with the performance requirements of the appropriate TSO. While the statement of compliance is important in equipping the aircraft, per § 91.225, correct installation is critical for the equipment to operate properly.
(b) Manufacturers of equipment intended for installation in experimental aircraft and E-LSAs are responsible to perform appropriate engineering efforts to determine that the equipment complies with all § 91.227 and TSO performance requirements before making their statement of compliance. The FAA will not approve or concur with manufacturers’ statements of compliance for this equipment. Manufacturers of this equipment should also consider the guidance in AC 20-165 when creating installation instructions. After making their statement of compliance, manufacturers of experimental aircraft and E-LSA equipment should be prepared to provide in-service product support to include design changes, equipment modifications (or instructions for performing them), and revisions to the installation, operating, and maintenance instructions.
Par 4-3 Page 11
(c) Owners of experimental aircraft should retain the installation instructions from the equipment supplier, including the statement of compliance, in the aircraft records to support the equipment’s compliance with the requirements of § 91.225 and § 91.227, and to assist in resolving in-service issues if necessary.
(4) All Aircraft—Importance of Proper Installation. Experience with FAA compliance monitoring of ADS-B Out-equipped aircraft to date has revealed that a large percentage of equipped aircraft have deficiencies with ADS-B Out system performance following initial installations. Many of these deficiencies have been attributed to improper installation and incorrect system configuration. Therefore, the FAA considers it particularly important for equipment manufacturers to provide installation instructions that are as clear and easy to follow as possible and revise these instructions when deficiencies in the instructions are discovered. Installers should adhere to the manufacturer’s installation instructions and employ practices that consistently result in ADS-B Out system installations that fully comply with § 91.227 equipment performance requirements.
(5) All Aircraft—Equipment Performance During Operation.
(a) If ADS-B Out performance becomes deficient during flight in § 91.225 airspace, ATC may require the aircraft to exit the airspace.
(b) The FAA continuously monitors compliance to the ADS-B Out equipment performance requirements. If FAA monitoring finds noncompliant equipment, aircraft with the noncompliant equipment installed may be denied access to § 91.225 airspace until the noncompliant equipment is corrected. This may require technical assistance from the applicable equipment manufacturers. Depending on the nature and scope of the noncompliance, the FAA may disqualify either an individual aircraft’s equipment (e.g., for improperly installed equipment on that specific aircraft), or all aircraft equipped with a certain type of equipment (e.g., for a design- or manufacturing-related equipment performance problem, or a problem traced to deficiencies with the installation, operating, or maintenance instructions, that may affect multiple aircraft).
(c) The FAA provides a service that enables aircraft owner/operators to verify compliance of ADS-B Out equipment performance requirements. Information on this service can be found at https://www.faa.gov/nextgen/equipadsb/. Owner/operators are encouraged to verify equipment performance through this service following installation, modification, or maintenance (to include component software updates) of ADS-B Out systems.
c. ATC-Authorized Deviations. Under § 91.225(g), operators must make requests for ATC-authorized deviations from the requirements in § 91.225 to the ATC facility that has jurisdiction over the concerned airspace or airport movement area within the time periods specified below:
Par 4-3 Page 12
(1) For operation of an aircraft with inoperative ADS-B equipment to the airport of ultimate destination (including any intermediate stops) to proceed to a place where suitable repairs can be made, or both, the request may be made at any time.
(2) For operation of an aircraft that is not equipped with ADS-B, operators must make the request at least 1 hour before the proposed operation.
4-4. FLIGHT PLANS (FP). When operating aircraft equipped with ADS-B, operators need to indicate their surveillance equipment code in field 10B of the U.S. Area Navigation (RNAV) and International Civil Aviation Organization (ICAO) FPs.
a. Transponder Codes. The transponder codes for ADS-B are as follows:
(1) E: Mode S, including Aircraft Identification (ACID), pressure-altitude, and Extended Squitter (ES) (ADS-B) capability.
(2) L: Mode S, including ACID, pressure-altitude, ES (ADS-B), and enhanced surveillance capability.
b. Surveillance Codes. The surveillance codes for ADS-B are as follows:
(1) B1: ADS-B with dedicated 1090 megahertz (MHz) ADS-B Out capability.
(2) B2: ADS-B with dedicated 1090 MHz ADS-B Out and In capability.
(3) U1: ADS-B Out capability using Universal Access Transceiver (UAT).
(4) U2: ADS-B Out and In capability using UAT.
c. ICAO FP Block 18 ADS-B Information.
(1) If ADS-B capability filed in item 10 is compliant with TSO-C166b, which is based on RTCA, Inc. DO-260B, include the item “SUR/260B.” If ADS-B capability filed in item 10 is compliant with TSO-C154c, which is compliant with RTCA DO-282B, include the item “SUR/282B.” If ADS-B capability filed in item 10 is not compliant with either TSO-C166b or TSO-C154c, include no “SUR/” information in this flight plan field.
(2) When ADS-B capability is filed in item 10, include CODE/Aircraft address expressed in the form of six hexadecimal characters (e.g., “CODE/HJF34B”).
NOTE: For a complete description of FP filing codes, including field 18, refer to the FAA Flight Planning Information Web site at http://www.faa.gov/about/office_org/headquarters_offices/ato/service_units/e nroute/flight_plan_filing.
Par 4-5 Page 13
4-5. PREFLIGHT REQUIREMENTS (U.S.-DESIGNATED AIRSPACE).
a. Flight Planning Requirements.
(1) Under § 91.103, pilots and operators must use all available information in planning their flight, to ensure that the performance requirements will be met for the duration of the flight.
Variations in position source performance affect ADS-B Out in two specific broadcast elements required by § 91.227—Navigation Accuracy Category for Position (NACp) and Navigation Integrity Category (NIC). During certain Global Positioning System (GPS) constellation geometries, some position sources may produce values for NACp and NIC that are less than required by the rule.
(2) Three different variants of GPS receivers are currently in use as a position source that can meet ADS-B Out rule performance requirements, to varying degrees, when adequate numbers of GPS satellites are in view. Selective Availability (SA) is a feature that deliberately degraded the GPS satellite signal, resulting in a less accurate reported position. SA was deactivated in 2000; however, SA-On GPS receivers assume SA is still active (on), thereby unnecessarily inflating integrity and accuracy bounds of the positions that are no longer degraded by SA. Most GPS receivers that are only compliant with TSO-C129 are SA-On receivers.
SA-Aware GPS receivers are designed to recognize that SA is inactive and optimize the performance from GPS. GPS receivers that comply with the performance requirements of TSO-C196 are SA-Aware receivers. Satellite Based Augmentation Systems (SBAS) receivers also use the additional signals from geostationary satellites specifically designed for aviation use, improving the quality and robustness of positioning performance. This difference in performance is most pronounced for very precise operations, such as Localizer Performance with Vertical Guidance (LPV) approaches, and for all operations when there are inoperative GPS satellites.
GPS receivers complying with TSO-C145 or TSO-C146 are SBAS receivers.
NOTE: Some GPS receivers manufactured with a TSO-C129a approval are SA-Aware, and, therefore, have the same NACp and NIC availability as TSO-C196() approved equipment. Operators should check with their GPS receiver supplier to verify whether their installed TSO-C129() GPS receiver is SA-On or SA-Aware.
NOTE: The wide area augmentation system (WAAS) is the designation of the SBAS system available in North America and is the term often used when making reference to SBAS in the United States.
b. ATC Authorization. It may be necessary for ATC to authorize operations in airspace for which ADS-B Out is required at times when the required performance cannot be met. During interference outages of GNSS (scheduled or unscheduled), the FAA may revert to alternate surveillance, as necessary, for affected areas. ATC will issue a Notice to Airmen (NOTAM) that authorizes such operations and identifies the airspace and time periods that the authorization is in effect. ATC will also issue a NOTAM to authorize performance outages when the FAA-provided preflight availability prediction tool is not available.
Par 4-5 Page 14
c. GPS Performance Prediction. Operators flying aircraft equipped with SBAS (TSO-C145 or TSO-C146) receivers do not need to conduct a preflight availability prediction because the FAA will issue a NOTAM whenever SBAS performance is not adequate. If TSO-C129() or TSO-C196() equipment is used for ADS-B Out, NACp and NIC availability prediction should be performed for the intended route of flight (route and time) using available GPS satellite information.
(1) Prediction Methods. Operators may use any of the following preflight availability prediction methods.
(a) Operators of large fleets of aircraft or users of flight planning programs may wish to use their own preflight availability verification tool. The operator is responsible for selecting a tool that accurately predicts the performance for their aircraft. The tool needs to account for the GPS satellites that are in service at the time of the prediction, and may take into account unique characteristics of the GNSS receiver, aircraft integration or installation; including performance better than required in FAA standards or use of inertial information integrated into the ADS-B Out position source. The FAA does not evaluate or approve a particular tool, but may evaluate the basis of the operator's determination that the tool is appropriate to their aircraft, particularly if its use results in noncompliant flights in airspace where ADS-B Out is required.
(b) Operators may use the FAA-provided preflight availability prediction tool, called the Service Availability Prediction Tool (SAPT) (http://sapt.faa.gov). Refer to the current edition of the SAPT User Guide for specific instructions on its use.
(c) Operators may use a third-party interface, incorporating FAA GPS performance prediction data without altering performance values, to predict NACp/NIC performance outages for the aircraft’s predicted flightpath and times.
(2) Prediction Model Parameters. The operator should use a model appropriate to their equipment, including the type of GPS receiver and the demonstrated capability to track satellites at a given mask angle. When selecting a mask angle, the operator should consider the equipment qualification, installation in the aircraft, and the effects of normal maneuvering.
Aircraft are typically qualified with a five degree mask angle, and operational experience has indicated that a two degree mask angle can be achieved by some equipment installations. If using the SAPT, each prediction is valid for the operation within 5 minutes of the plan time and
7.5 NM of the route. The operator may wish to submit additional requests for predictions for varying times around the proposed departure time to ensure compliance at the actual departure time.
(3) Flight Planning Guidance. Predictions can be used for initial flight planning as early as 72 hours prior to the planned departure. However, the operator should conduct a performance prediction as close to departure time as feasible, but with sufficient time to replan the flight or obtain ATC prior approval in the event a segment of the flight will not be compliant.
The prediction should be reevaluated prior to flight if a new NOTAM identifies an unscheduled GPS satellite outage.