AD 2005-26-01

Airworthiness directive · Fail-safe fastener assembly · Dassault FALCON 2000

Effective
January 24, 2006
Published
December 20, 2005 · 70 FR 75386–75388
Issued
December 8, 2005
Model
FALCON 2000
Data sheet
TCDSA50NM
Registered aircraft
153 matched by model
Product
Aircraft · Large airplane
Amendment
39-14422
Docket
FAA-2005-22633
Issued as
Final rule

Unofficial copy from the Federal Register XML, document 05-24150. Only the govinfo PDF is the legal edition. DRS record last changed May 30, 2024.

On this page

Summary

The FAA is adopting a new airworthiness directive (AD) for certain Dassault Model Falcon 2000 airplanes. This AD requires an inspection for the presence of fail-safe pins, nuts, and washers on each engine, and replacement of the fail-safe fastener assembly with a new assembly if necessary. This AD results from a report of a missing pin of a fail-safe fastener. We are issuing this AD to prevent reduced structural integrity of an engine mount due to a missing pin of a fail-safe fastener, and possible separation of an engine from the airplane during flight.

The airworthiness directive

2005-26-01 Dassault Aviation: Amendment 39-14422. Docket No. FAA-2005-22633; Directorate Identifier 2005-NM-155-AD.

(a) Effective Date

PDF page 2

(a) This AD becomes effective January 24, 2006.

(b) Affected ADs

PDF page 2

(b) None.

(c) Applicability

PDF page 2

(c) This AD applies to Dassault Model Falcon 2000 airplanes, certificated in any category; up to and including serial number 212, excluding serial number 208.

(d) Unsafe Condition

PDF page 2

(d) This AD results from a report of a missing pin of a fail-safe fastener. We are issuing this AD to prevent reduced structural integrity of an engine mount due to a missing pin of a fail-safe fastener, and possible separation of an engine from the airplane during flight.

(e) Compliance

PDF page 2

(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

(f) Inspection and Replacement

PDF page 2

(f) Before the accumulation of 3,750 total landings, or within 2 months after the effective date of this AD, whichever occurs later: Do a detailed inspection for the presence of fail-safe pins, nuts, and washers on each engine, in accordance with the Accomplishment Instructions of Dassault Service Bulletin F2000-301, dated February 2, 2005. If any component is found missing at an attachment point, before further flight, replace the fail-safe fastener assembly with a new assembly, in accordance with the service bulletin.

Note 1:

For the purposes of this AD, a detailed inspection is: “An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirror, magnifying lenses, etc., may be necessary. Surface cleaning and elaborate procedures may be required.”

(g) Inspections and replacements done in accordance with Chapter 54-003, dated December 2002, of the Dassault Falcon 2000 Maintenance Manual are acceptable for compliance with the requirements of paragraph (f) of this AD.

(h) No Reporting

PDF page 2

(h) Although the service bulletin referenced in this AD specifies to submit certain information to the manufacturer, this AD does not include that requirement.

(i) Alternative Methods of Compliance (AMOCs)

PDF page 2

(i)(1) The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19.

(2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office.

(j) Related Information

PDF page 2

(j) French airworthiness directive F-2005-018, dated February 2, 2005, also addresses the subject of this AD.

(k) Material Incorporated by Reference

PDF page 2

(k) You must use Dassault Service Bulletin F2000-301, dated February 2, 2005, to perform the actions that are required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approved the incorporation by reference of this document in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606, for a copy of this service information. You may review copies at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL-401, Nassif Building, Washington, DC; on the Internet at http://dms.dot.gov; or at the National Archives and Records Administration (NARA). For information on the availability of this material at the NARA, call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Rule preamble

The FAA’s background, reasoning and cost estimate, published with the AD.

DatesPage 1

This AD becomes effective January 24, 2006.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of January 24, 2006.

AddressesPage 1

You may examine the AD docket on the Internet at http://dms.dot.gov or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, Room PL-401, Washington, DC.

Contact Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606, for service information identified in this AD.

For further information contactPage 1

Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-1137; fax (425) 227-1149.

Examining the DocketPage 1

You may examine the airworthiness directive (AD) docket on the Internet at http://dms.dot.gov or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the street address stated in the ADDRESSES section.

DiscussionPage 2

The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to certain Dassault Model Falcon 2000 airplanes. That NPRM was published in the Federal Register on October 7, 2005 (70 FR 58634). That NPRM proposed to require an inspection for the presence of fail-safe pins, nuts, and washers on each engine, and replacement of the fail-safe fastener assembly with a new assembly if necessary.

CommentsPage 2

We provided the public the opportunity to participate in the development of this AD. We received no comments on the NPRM or on the determination of the cost to the public.

ConclusionPage 2

We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed.

Costs of CompliancePage 2

This AD will affect about 149 airplanes of U.S. registry. The required inspection will take about 1 work hour per airplane, at an average labor rate of $65 per work hour. Based on these figures, the estimated cost of the inspection required by this AD for U.S. operators is $9,685, or $65 per airplane.

Authority for This RulemakingPage 2

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory findingsPage 2

We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a “significant regulatory action” under Executive Order 12866;

(2) Is not a “significant rule” under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation.

Adoption of the amendmentPage 2

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

1. The authority citation for part 39 continues to read as follows:

2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD):

Affected TCDS · 1

The type certificate data sheets for the models this AD names, matched by model and maker.

Registered aircraft · 153

Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.

By aircraft maker
  • Dassault153 aircraft
By year built
19762019
Registered aircraft by year built: 144 aircraft
19761
19931
19942
19959
199615
19978
19989
199923
200016
200121
200225
20034
20044
20053
20062
20191

9 with no year recorded

By model

Aircraft

See all 153 aircraft