AD 2011-09-11

(a) This AD is effective June 6, 2011.

(b) None.

(c) This AD applies to The Boeing Company Model 777-200 and -300 series airplanes, certificated in any category; equipped with Pratt and Whitney engines; as identified in Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010.

(d) Joint Aircraft System Component (JASC)/Air Transport Association (ATA) of America Code 54: Nacelles/Pylons.

(e) This AD was prompted by reports of system disconnect boxes that have been contaminated with hydraulic fluid, in which one case a crack was found. We are issuing this AD to detect and correct hydraulic fluid contamination, which can cause cracking of titanium parts in the system disconnect assembly, resulting in compromise of the engine firewall. A cracked firewall can allow fire in the engine area to enter the strut and can lead to an uncontained engine strut fire if flammable fluid is present. Cracking of the disconnect box may also reduce the effectiveness of the fire extinguishing system in the engine compartment and could contribute to an uncontained engine fire. In addition, a cracked disconnect box can leak flammable fluids into the engine core, which can initiate an engine fire and lead to one or both fire conditions discussed above.

(f) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

(g) Within 12 months after the effective date of this AD: Do a general visual inspection for hydraulic fluid contamination of the interior of the strut disconnect assembly, in accordance with Part 1 of the Accomplishment Instructions of Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010.

(1) For airplanes on which no hydraulic fluid contamination is found (Condition 1): Repeat the general visual inspection required by paragraph (g) of this AD thereafter at intervals not to exceed 6,000 flight cycles or 750 days, whichever occurs first.

(2) For airplanes on which hydraulic fluid contamination is found (Condition 2): Before further flight, do a detailed inspection for discrepancies (e.g., hydraulic fluid coking, heat discoloration, cracks, and etching or pitting) of the interior of the strut disconnect assembly, in accordance with Part 2 of the Accomplishment Instructions of Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010.

(i) For airplanes on which no discrepancy is found during the inspection required by paragraph (g)(2) of this AD (Condition 2A): Repeat the detailed inspection required by paragraph (g)(2) of this AD thereafter at intervals not to exceed 6,000 flight cycles or 750 days, whichever occurs first.

(ii) For airplanes on which hydraulic fluid coking or heat discoloration is found but no cracking, etching, or pitting is found during the inspection required by paragraph (g)(2) of this AD (Condition 2B): Do the actions required by paragraph (g)(2)(ii)(A) and (g)(2)(ii)(B) of this AD.

(A) Within 300 flight cycles after doing the inspection required by paragraph (g)(2) of this AD: Do a detailed inspection of the exterior of the strut disconnect assembly for cracks, in accordance with Part 3 of the Accomplishment Instructions of Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010; and repeat the detailed inspection thereafter at intervals not to exceed 300 flight cycles.

(B) Within 6,000 flight cycles or 750 days after hydraulic fluid coking and/or heat discoloration was found during the inspection required by paragraph (g)(2) of this AD, whichever occurs first: Replace the titanium system disconnect assembly with an Inconel system, in accordance with Part 4 of the Accomplishment Instructions of Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010.

(h) For airplanes on which any crack, etching, or pitting is found during any inspection required by paragraph (g)(2) or (g)(2)(ii)(A) of this AD (Condition 3): Before further flight, replace the titanium system disconnect assembly with an Inconel system, in accordance with Part 4 of the Accomplishment Instructions of Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010.

(i) Replacing the titanium system disconnect assembly with an Inconel system disconnect assembly in accordance with Part 4 of the Accomplishment Instructions of Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010, terminates the actions required by this AD.

(j) Actions accomplished before the effective date of this AD according to Boeing Alert Service Bulletin 777-54A0024, dated April 1, 2010, are considered acceptable for compliance with the corresponding actions specified in this AD.

(k)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. Information may be e-mailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

(l) For more information about this AD, contact Kevin Nguyen, Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification Office (ACO), 1601 Lind Avenue, SW., Renton, Washington 98057-3356; phone: 425-917-6501; fax: 425-917-6590; e-mail: kevin.nguyen@faa.gov.

(m) You must use Boeing Service Bulletin 777-54A0024, Revision 1, dated November 4, 2010, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone 206-544-5000, extension 1; fax 206-766-5680; e-mail me.boecom@boeing.com; Internet https://www.myboeingfleet.com.

(3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221.

(4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at an NARA facility, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.