AD 2017-09-03

Historical

Airworthiness directive · Periodic inspections · Dassault Mystere-Falcon 50

Effective
June 13, 2017
Published
May 9, 2017 · 82 FR 21467–21469
Issued
April 24, 2017
Supersedes
AD2013-03-12
Superseded by
AD2023-05-15
Model
Mystere-Falcon 50
Data sheet
TCDSA46EU
Registered aircraft
90 matched by model
Product
Aircraft · Large airplane
ATA chapter
05 · Time limits and maintenance checks
Amendment
39-18865
Docket
FAA-2016-9569
Project
2016-NM-052-AD
Issued as
Final rule

Unofficial copy from the Federal Register XML, document 2017-08829. Only the govinfo PDF is the legal edition. DRS record last changed November 21, 2025.

On this page

Summary

We are superseding Airworthiness Directive (AD) 2013-03-12 for all Dassault Aviation Model MYSTERE-FALCON 50 airplanes. AD 2013-03-12 required revising the maintenance program to incorporate certain maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or revised maintenance requirements and airworthiness limitations. This AD was prompted by issuance of a revision to the airplane maintenance manual (AMM) that introduces new or more restrictive maintenance requirements and/or airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.

The airworthiness directive

2017-09-03 Dassault Aviation: Amendment 39-18865; Docket No. FAA-2016-9569; Directorate Identifier 2016-NM-052-AD.

(a) Effective Date

PDF page 2

This AD is effective June 13, 2017.

(b) Affected ADs

PDF page 2

(1) This AD replaces AD 2013-03-12, Amendment 39-17347 (78 FR 9798, February 12, 2013) (“AD 2013-03-12”).

(2) This AD affects AD 2010-26-05, Amendment 39-16544 (75 FR 79952, December 21, 2010) (“AD 2010-26-05”), and AD 2012-02-18, Amendment 39-16941 (77 FR 12175, February 29, 2012) (“AD-2012-02-18”).

(c) Applicability

PDF page 2

This AD applies to Dassault Aviation Model MYSTERE-FALCON 50 airplanes, certificated in any category, all manufacturer serial numbers.

(d) Subject

PDF page 2

Air Transport Association (ATA) of America Code 05, Periodic inspections.

(e) Reason

PDF page 2

This AD was prompted by a manufacturer revision to the airplane maintenance manual (AMM) that introduces new or more restrictive maintenance requirements and/or airworthiness limitations. We are issuing this AD to prevent reduced structural integrity of the airplane.

(f) Compliance

PDF page 2

Comply with this AD within the compliance times specified, unless already done.

(g) Retained Maintenance Program Revision, With No Changes

PDF page 2

This paragraph restates the requirements of paragraph (g) of AD 2013-03-12, with no changes. Within 30 days after March 19, 2013 (the effective date of AD 2013-03-12): Revise the maintenance program to incorporate all airworthiness limitations and maintenance tasks specified in Section 05-40/00, Airworthiness Limitations, of Chapter 5-40, Airworthiness Limitations, of the Dassault Falcon 50/50EX Maintenance Manual, Revision 21, dated June 2011. The initial compliance times for the tasks are at the applicable times specified in Section 05-40/00, Airworthiness Limitations, of Chapter 5-40, Airworthiness Limitations, of the Dassault Falcon 50/50EX Maintenance Manual, Revision 21, dated June 2011, or within 30 days after March 19, 2013, whichever occurs later.

(h) Retained Provision Regarding Alternative Actions, Intervals, and Critical Design Configuration Control Limitations (CDCCLs), With New Exception

PDF page 3

This paragraph restates the requirements of paragraph (h) of AD 2013-03-12, with a new exception. Except as required by paragraph (i) of this AD: After accomplishing the revisions required by paragraph (g) of this AD, no alternative actions ( e.g., inspections), intervals, and/or CDCCLs may be used other than those specified in Section 05-40/00, Airworthiness Limitations, of Chapter 5-40, Airworthiness Limitations, of the Dassault Falcon 50/50EX Maintenance Manual, Revision 21, dated June 2011, unless the actions, intervals, and/or CDCCLs are approved as an alternative methods of compliance (AMOC) in accordance with the procedures specified in paragraph (l)(1) of this AD.

(i) New Maintenance or Inspection Program Revision

PDF page 3

Within 30 days after the effective date of this AD: Revise the maintenance or inspection program, as applicable, to incorporate airworthiness limitations, maintenance tasks, and associated thresholds and intervals specified in Section 05-40/00, Airworthiness Limitations, of Chapter 5-40, Airworthiness Limitations, of the Erratum to Dassault Falcon 50/50EX Maintenance Manual, Revision 23, dated July 2015. The initial compliance times for the tasks are at the applicable times specified in Section 05-40/00, Airworthiness Limitations, of Chapter 5-40, Airworthiness Limitations, of the Erratum to Dassault Falcon 50/50EX Maintenance Manual, Revision 23, dated July 2015, or within 30 days after the effective date of this AD, whichever occurs later. Accomplishing the revision of the maintenance or inspection program required by this paragraph terminates the requirements of paragraph (g) of this AD.

(j) New Provision Regarding Alternative Actions and Intervals

PDF page 3

After the maintenance or inspection program has been revised as required by paragraph (i) of this AD, no alternative actions ( e.g., inspections) or intervals may be used unless the actions and intervals are approved as an AMOC in accordance with the procedures specified in paragraph (l)(1) of this AD.

(k) Terminating Action for Certain ADs

PDF page 3

Accomplishing the actions required by paragraph (g) or (i) of this AD terminates all requirements of AD 2010-26-05 and AD 2012-02-18 for the Dassault Aviation Model MYSTERE-FALCON 50 airplanes specified in those ADs.

(l) Other FAA AD Provisions

PDF page 3

The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD.

(2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; or the European Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.

(m) Related Information

PDF page 3

(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA Airworthiness Directive 2016-0067, dated April 7, 2016, for related information. This MCAI may be found in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-9569.

(2) For more information about this AD, contact Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; fax 425-227-1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov.

(3) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (n)(5) and (n)(6) of this AD.

(n) Material Incorporated by Reference

PDF page 3

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise.

(3) The following service information was approved for IBR as of June 13, 2017.

(i) Chapter 5-40, Airworthiness Limitations, of the Erratum to Dassault Falcon 50/50EX Maintenance Manual, Revision 23, dated July 2015.

(ii) Reserved.

(4) The following service information was approved for IBR on March 19, 2013 (78 FR 9798, February 12, 2013).

(i) Section 05-40/00, Airworthiness Limitations, of Chapter 5-40, Airworthiness Limitations, of the Dassault Falcon 50/50EX Maintenance Manual, Revision 21, dated June 2011.

(ii) Reserved.

(5) For service information identified in this AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; Internet http://www.dassaultfalcon.com.

(6) You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.

(7) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

Rule preamble

The FAA’s background, reasoning and cost estimate, published with the AD.

DatesPage 1

This AD is effective June 13, 2017.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of June 13, 2017.

The Director of the Federal Register approved the incorporation by reference of a certain other publication listed in this AD as of March 19, 2013 (78 FR 9798, February 12, 2013).

AddressesPage 1

For service information identified in this final rule, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; Internet http://www.dassaultfalcon.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-9569.

For further information contactPage 1

Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, WA 98057-3356; telephone 425-227-1137; fax 425-227-1149.

DiscussionPage 1

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to supersede AD 2013-03-12, Amendment 39-17347 (78 FR 9798, February 12, 2013) (“AD 2013-03-12”). AD 2013-03-12 applied to all Dassault Aviation Model MYSTERE-FALCON 50 airplanes. The NPRM published in the Federal Register on January 6, 2017 (82 FR 1621). The NPRM was prompted by the issuance of a revision to the AMM that introduced new or more restrictive maintenance requirements and/or airworthiness limitations. The NPRM proposed to require revising the maintenance or inspection program, as applicable, to incorporate new or revised maintenance requirements and airworthiness limitations. We are issuing this AD to prevent reduced structural integrity of the airplane.

The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued EASA Airworthiness Directive 2016-0067, dated April 7, 2016 (referred to after this as the Mandatory Continuing Airworthiness Information, or “the MCAI”), to correct an unsafe condition for all Dassault Aviation Model MYSTERE-FALCON 50 airplanes. The MCAI states:

The airworthiness limitations and maintenance requirements for the Mystère Falcon 50 type design are included in DA Mystère Falcon 50 Aircraft Maintenance Manual (AMM) chapter 5-40 and are approved by EASA.

Failure to implement these limitations or accomplish these tasks could result in an unsafe condition [reduced structural integrity of the airplane]. Consequently, compliance with these actions has been identified as mandatory for continued airworthiness.

Consequently, EASA issued AD 2011-0246 [which corresponds to FAA AD 2013-03-12] to require accomplishment of the maintenance tasks, and implementation of the airworthiness limitations, as specified in DA Mystère Falcon 50 AMM chapter 5-40 Revision 21.

Since that [EASA] AD was issued, DA issued revision 23 of the Mystere Falcon 50 AMM chapter 5-40 (hereafter referred to as `the ALS' in this [EASA] AD), which introduces new and more restrictive maintenance requirements and/or airworthiness limitations.

The ALS introduces, among others, the following changes:

—Addition of more detailed data regarding SSIP program,

—Task 53-50-35-220-802 “Detailed inspection of the frame 35 upper and lower sections”, replacing Task 53-50-35-220-801,

—Task 55-00-00-270-801 “Ultrasonic inspection for stress corrosion in stabilizer hinges”, replacing Task 55-00-00-250-801, and

—Task 78-31-00-250-802 “Special detailed inspection (fluorescent penetrant) of thrust reverser door hinge fittings”, replacing Task 78-31-00-250-801.

For the reasons described above, this [EASA] AD, retains the requirements of EASA AD 2011-0246, which is superseded, and requires the implementation of the maintenance tasks and airworthiness limitations, as specified in the ALS.

This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or revised maintenance requirements and airworthiness limitations. You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-9569.

CommentsPage 2

We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.

ConclusionPage 2

We reviewed the relevant data and determined that air safety and the public interest require adopting this AD as proposed except for minor editorial changes. We have determined that these minor changes:

• Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and

• Do not add any additional burden upon the public than was already proposed in the NPRM.

Related Service Information Under 1 CFR Part 51Page 2

We reviewed Chapter 5-40, Airworthiness Limitations, of the Erratum to Dassault Falcon 50/50EX Maintenance Manual, Revision 23, dated July 2015. This service information describes maintenance requirements and/or airworthiness limitations. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

Costs of CompliancePage 2

We estimate that this AD affects 249 airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

Estimated Costs
ActionLabor costParts costCost per productCost on U.S. operators
Maintenance program revision (retained action from AD 2013-03-12)1 work-hour × $85 per hour = $85$0$85$21,165
Maintenance or inspection program revision (new action)1 work-hour × $85 per hour = $8508521,165
Authority for This RulemakingPage 2

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory findingsPage 2

We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);

3. Will not affect intrastate aviation in Alaska; and

4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

Adoption of the AmendmentPage 2

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

Adoption of the amendmentPage 2

1. The authority citation for part 39 continues to read as follows:

2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):

Affected TCDS · 1

The type certificate data sheets for the models this AD names, matched by model and maker.

Registered aircraft · 90

Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.

By aircraft maker
  • Dassault88 aircraft
  • Avions Marcel Dassault Breguet2 aircraft
By year built
19802007
Registered aircraft by year built: 85 aircraft
19802
19823
19842
19881
19901
19913
19922
19931
19951
19962
19973
19984
19999
200014
200110
20029
20034
20044
20054
20063
20073

5 with no year recorded

By model

Aircraft

See all 90 aircraft