AD 2024-07-02

Airworthiness directive · Turbine Section · CFM International LEAP-1A23, LEAP-1A24, LEAP-1A24E1 and 10 more

Effective
June 10, 2024
Published
May 6, 2024 · 89 FR 37111–37113
Issued
March 27, 2024
Models
LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1 and 7 more
Data sheet
TCDSE00089EN
Registered aircraft
208 matched by model
Product
Engine · Large airplane
ATA chapter
72 · Engine
Amendment
39-22722
Docket
FAA-2024-0030
Project
AD-2023-01066-E
Issued as
Final rule

Unofficial copy from the Federal Register XML, document 2024-09564. Only the govinfo PDF is the legal edition. DRS record last changed November 21, 2025.

On this page

Summary

The FAA is adopting a new airworthiness directive (AD) for CFM International, S.A. (CFM) Model LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP-1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, and LEAP-1A35A engines. This AD was prompted by detection of melt-related freckles in the billet, which may reduce the life of certain high-pressure turbine (HPT) rotor interstage seals. This AD requires removing the affected HPT rotor interstage seals from service and replacing with a part eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.

The airworthiness directive

2024-07-02 CFM International, S.A.: Amendment 39-22722; Docket No. FAA-2024-0030; Project Identifier AD-2023-01066-E.

(a) Effective Date

PDF page 2

This airworthiness directive (AD) is effective June 10, 2024.

(b) Affected ADs

PDF page 2

None.

(c) Applicability

PDF page 2

This AD applies to CFM International, S.A. (CFM) Model LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP-1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, and LEAP-1A35A engines.

(d) Subject

PDF page 2

Joint Aircraft System Component (JASC) Code 7250, Turbine Section.

(e) Unsafe Condition

PDF page 2

This AD was prompted by detection of melt-related freckles in the billet, which may reduce the life of certain high-pressure turbine (HPT) rotor interstage seals. The FAA is issuing this AD to prevent failure of the HPT rotor interstage seal. The unsafe condition, if not addressed, could result in release of uncontained debris, damage to the engine, and damage to the airplane.

(f) Compliance

PDF page 3

Comply with this AD within the compliance times specified, unless already done.

(g) Required Actions

PDF page 3

For engines with an affected HPT rotor interstage seal installed, before exceeding the applicable threshold specified in Table 1 of paragraph 3.E., Compliance, of CFM Service Bulletin (SB) LEAP-1A-72-00-0492-01A-930A-D, Issue 001-00, dated April 6, 2023 (CFM SB LEAP-1A-72-00-0492-01A-930A-D, Issue 001-00), or at the next HPT rotor module exposure, whichever occurs first after the effective date of this AD, remove the affected HPT rotor interstage seal from service and replace it with a part eligible for installation.

(h) Definitions

PDF page 3

(1) For the purpose of this AD, an “affected HPT rotor interstage seal” is any HPT rotor interstage seal having part number 2466M68P02 and a serial number listed in Table 1 of paragraph 3.E., Compliance, of CFM SB LEAP-1A-72-00-0492-01A-930A-D, Issue 001-00.

(2) For the purpose of this AD, a “part eligible for installation” is any HPT rotor interstage seal having a serial number that is not listed in Table 1 of paragraph 3.E., Compliance, of CFM SB LEAP-1A-72-00-0492-01A-930A-D, Issue 001-00.

(3) For the purpose of this AD, an “HPT rotor module exposure” is an engine shop visit during which the HPT rotor assembly is fully removed from the engine core.

(i) Alternative Methods of Compliance (AMOCs)

PDF page 3

(1) The Manager, AIR-520 Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the AIR-520 Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (j) of this AD and email to ANE-AD-AMOC@faa.gov.

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

(j) Additional Information

PDF page 3

For more information about this AD, contact Mehdi Lamnyi, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 238-7743; email: mehdi.lamnyi@faa.gov.

(k) Material Incorporated by Reference

PDF page 3

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise.

(i) CFM International, S.A. Service Bulletin LEAP-1A-72-00-0492-01A-930A-D, Issue 001-00, dated April 6, 2023.

(ii) [Reserved]

(3) For service information, contact CFM International, S.A., GE Aviation Fleet Support, 1 Neumann Way, M/D Room 285, Cincinnati, OH 45215; phone: (877) 432-3272; email: aviation.fleetsupport@ge.com.

(4) You may view this service information at FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (817) 222-5110.

(5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locationsoremailfr.inspection@nara.gov.

Rule preamble

The FAA’s background, reasoning and cost estimate, published with the AD.

DatesPage 1

This AD is effective June 10, 2024.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of June 10, 2024.

AddressesPage 1

AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA-2024-0030; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

Material Incorporated by Reference:

• For service information identified, contact CFM International, S.A., GE Aviation Fleet Support, 1 Neumann Way, M/D Room 285, Cincinnati, OH 45215; phone: (877) 432-3272; email: aviation.fleetsupport@ge.com.

• You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (817) 222-5110. It is also available at regulations.gov under Docket No. FAA-2024-0030.

For further information contactPage 2

Mehdi Lamnyi, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 238-7743; email: mehdi.lamnyi@faa.gov.

BackgroundPage 2

The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to CFM Model LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP-1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, and LEAP-1A35A engines. The NPRM published in the Federal Register on January 11, 2024 (89 FR 1847). The NPRM was prompted by detection of melt-related freckles in the billet, which may reduce the life of certain HPT rotor interstage seals. In the NPRM, the FAA proposed to require removing the affected HPT rotor interstage seals from service and replacing with a part eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.

CommentsPage 2

The FAA received no comments on the NPRM or on the determination of the costs.

ConclusionPage 2

The FAA reviewed the relevant data and determined that air safety requires adopting this AD as proposed. Accordingly, the FAA is issuing this AD to address the unsafe condition on these products. Except for minor editorial changes, this AD is adopted as proposed in the NPRM.

Related Service Information Under 1 CFR Part 51Page 2

The FAA reviewed CFM Service Bulletin LEAP-1A-72-00-0492-01A-930A-D, Issue 001-00, dated April 6, 2023, which provides the serial numbers of the affected HPT rotor interstage seals and specifies procedures for replacement of the HPT rotor interstage seal. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

Costs of CompliancePage 2

The FAA estimates that this AD affects 1 engine installed on an airplane of U.S. registry.

The FAA estimates the following costs to comply with this AD:

Estimated Costs
ActionLabor costParts costCost per productCost on U.S. operators
Remove HPT rotor interstage seal225 work-hours × $85 per hour = $19,125$168,000$187,125$187,125
Authority for This RulemakingPage 2

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory findingsPage 2

This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Will not affect intrastate aviation in Alaska, and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

The amendmentPage 2

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

Adoption of the amendmentPage 2

1. The authority citation for part 39 continues to read as follows:

2. The FAA amends § 39.13 by adding the following new airworthiness directive:

Affected TCDS · 1

The type certificate data sheets for the models this AD names, matched by model and maker.

Registered aircraft · 208

Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.

By aircraft maker
  • Airbus203 aircraft
  • Airbus S A S5 aircraft
By year built
20162026
Registered aircraft by year built: 208 aircraft
20163
201719
201825
201937
202026
202130
202237
202310
20248
20257
20266

By model

Aircraft

See all 208 aircraft