AD 2026-21-03

Airworthiness directive · Fuel · Airbus A330-243, A330-243F, A330-341 and 12 more

Effective
November 23, 2026
Published
October 19, 2026 · 91 FR 65952–65954
Issued
October 7, 2026
Models
A330-243, A330-243F, A330-341, A330-342, A330-343, A330-841 and 9 more
Registered aircraft
111 matched by model
Product
Aircraft · Large airplane
ATA chapter
28 · Fuel
Amendment
39-23492
Docket
FAA-2026-8780
Project
MCAI-2026-00262-T
Issued as
Final rule

Unofficial copy from the Federal Register XML, document 2026-21325. Only the govinfo PDF is the legal edition. DRS record last changed October 19, 2026.

On this page

Summary

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-243, A330-243F, A330-341, A330-342, A330-343, A330-841, and A330-941 airplanes; and Model A340-211, A340-212, A340-213, A340-311, A340-312, A340-313, A340-541, and A340-642 airplanes. This AD was prompted by reports of leaks on closed fuel low pressure shut-off valves (LPSOVs). This AD requires repetitive leak checks of certain fuel LPSOVs and replacement of an affected part if any discrepancy is detected. This AD also allows the installation of an affected part under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.

The airworthiness directive

2026-21-03 Airbus SAS: Amendment 39-23492; Docket No. FAA-2026-8780; Project Identifier MCAI-2026-00262-T.

(a) Effective Date

PDF page 3

This airworthiness directive (AD) is effective November 23, 2026.

(b) Affected ADs

PDF page 3

None.

(c) Applicability

PDF page 3

This AD applies to all Airbus SAS airplanes specified in paragraphs (c)(1) and (2) of this AD, certificated in any category.

(1) Model A330-243, A330-243F, A330-341, A330-342, A330-343, A330-841, and A330-941 airplanes.

(2) Model A340-211, A340-212, A340-213, A340-311, A340-312, A340-313, A340-541, and A340-642 airplanes.

(d) Subject

PDF page 3

Air Transport Association (ATA) of America Code 28, Fuel.

(e) Unsafe Condition

PDF page 3

This AD was prompted by reports of leaks on closed fuel low pressure shut-off valves (LPSOVs) due to the LPSOV failing to seal. The FAA is issuing this AD to address such leaks, which, depending on the amount of the leak, could sustain a fire. The unsafe condition, if not addressed, could lead to the inability to extinguish a fire and result in significant damage to airplane structure or systems.

(f) Compliance

PDF page 3

Comply with this AD within the compliance times specified, unless already done.

(g) Requirements

PDF page 3

Except as specified in paragraphs (h) and (i) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2026-0060R1, dated June 9, 2026 (EASA AD 2026-0060R1).

(h) Exceptions to EASA AD 2026-0060R1

PDF page 3

(1) Where Table 1 of EASA AD 2026-0060R1 specifies a compliance time of between November 12, 2025, and March 3, 2029, this AD requires accomplishing the initial leak check within 35 months after the effective date of this AD.

(2) Where EASA AD 2026-0060R1 refers to April 3, 2026 (the effective date of the original issue of EASA AD 2026-0060), this AD requires using the effective date of this AD.

(3) Where EASA AD 2026-0060R1 defines a serviceable part as “Any fuel LPSOV eligible for installation in accordance with Airbus instructions”, for this AD, replace that text with “Any fuel LPSOV eligible for installation”.

(4) Where paragraph (4) of EASA AD 2026-0060R1 specifies “any discrepancy of an affected part, as specified in the SB, is detected”, for this AD, replace that text with “any discrepancy of an affected part is detected”.

(5) This AD does not adopt the “Remarks” section of EASA AD 2026-0060R1.

(i) No Reporting and No Return of Parts

PDF page 3

Although the material referenced in EASA AD 2026-0060R1 specifies to submit certain information to the manufacturer and to send removed parts to the manufacturer, this AD does not include those requirements.

(j) Additional AD Provisions

PDF page 3

The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (k) of this AD and email to: AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.

(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR-520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.

(3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any material contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.

(k) Additional Information

PDF page 3

For more information about this AD, contact Anthony D. Decaro, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 562-627-5374; email: Anthony.D.Decaro@faa.gov.

(l) Material Incorporated by Reference

PDF page 3

(1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise.

(i) European Union Aviation Safety Agency (EASA) AD 2026-0060R1, dated June 9, 2026.

(ii) [Reserved]

(3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu.

(4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA 98198. For information on the availability of this material at the FAA, call 206-231-3195.

(5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email fr.inspection@nara.gov.

Rule preamble

The FAA’s background, reasoning and cost estimate, published with the AD.

DatesPage 1

This AD is effective November 23, 2026.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of November 23, 2026.

AddressesPage 1

AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA-2026-8780; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

Material Incorporated by Reference:

• For European Union Aviation Safety Agency (EASA) material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu.

• You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA 98198. For information on the availability of this material at the FAA, call 206-231-3195. It is also available at regulations.gov under Docket No. FAA-2026-8780.

For further information contactPage 1

Anthony D. Decaro, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 562-627-5374; email: Anthony.D.Decaro@faa.gov.

BackgroundPage 1

The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all Airbus SAS Model A330- 243, A330-243F, A330-341, A330-342, A330-343, A330-841, and A330-941 airplanes; and Model A340-211, A340-212, A340-213, A340-311, A340-312, A340-313, A340-541, and A340-642 airplanes. The NPRM was published in the Federal Register on August 13, 2026 (91 FR 52269). The NPRM was prompted by EASA AD 2026-0060R1, dated June 9, 2026 (EASA AD 2026-0060R1) (also referred to as the MCAI), issued by EASA, which is the Technical Agent for the Member States of the European Union. The MCAI states that occurrences of leaks on closed fuel LPSOVs were reported due to the LPSOV failing to seal. Depending on its amount, a fuel leak from an LPSOV could sustain a fire. This condition, if not detected and corrected, could lead to the inability to extinguish a fire and result in significant damage to airplane structure or systems.

In the NPRM, the FAA proposed to require repetitive leak checks of certain fuel LPSOVs and replacement of an affected part if any discrepancy is detected, as specified in EASA AD 2026-0060R1. The NPRM also proposed to allow the installation of an affected part under certain conditions, as specified in EASA AD 2026-0060R1. The FAA is issuing this AD to address the unsafe condition on these products.

You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA-2026-8780.

CommentsPage 2

The FAA received a comment from the Air Line Pilots Association, International (ALPA) who supported the NPRM without change.

ConclusionPage 2

These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA reviewed the relevant data, considered any comments received, and determined that air safety requires adopting this AD as proposed. Accordingly, the FAA is issuing this AD to address the unsafe condition on these products. Except for minor editorial changes, this AD is adopted as proposed in the NPRM. None of the changes will increase the economic burden on any operator.

Material Incorporated by Reference Under 1 CFR Part 51Page 2

EASA AD 2026-0060R1 specifies procedures for repetitive leak checks of the fuel LPSOVs to confirm that the LPSOV isolates the fuel supply to the associated engine, and replacement of an affected part if any discrepancy is detected ( e.g., any leak is found). EASA AD 2026-0060R1 also allows the installation of an affected part under certain conditions. EASA AD 2026-0060R1 also provides acceptable methods of compliance for the actions.

This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

Costs of CompliancePage 2

The FAA estimates that this AD affects 115 airplanes of U.S. registry. The FAA estimates the following costs to comply with this AD:

Estimated Costs for Required Actions
Labor costParts costCost per productCost on U.S. operators
Up to 8 work-hours × $85 per hour = $680$0Up to $680Up to $78,200.

The FAA estimates the following costs to do any necessary on-condition action that would be required based on the results of any required action. The FAA has no way of determining the number of aircraft that might need this on-condition action:

Estimated Costs of On-Condition Actions
Labor costParts costCost per product
5 work-hours × $85 per hour = $425$10,000$10,425
Authority for This RulemakingPage 2

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory findingsPage 2

This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Will not affect intrastate aviation in Alaska, and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

The amendmentPage 3

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

Adoption of the amendmentPage 3

1. The authority citation for part 39 continues to read as follows:

2. The FAA amends § 39.13 by adding the following new airworthiness directive:

Affected TCDS · 2

The type certificate data sheets for the models this AD names, matched by model and maker.

Registered aircraft · 111

Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.

By aircraft maker
  • Airbus108 aircraft
  • Airbus Industrie2 aircraft
  • Airbus S A S1 aircraft
By year built
20062025
Registered aircraft by year built: 94 aircraft
20061
20081
20093
20105
20116
20127
201313
201410
20153
20161
20171
20184
20194
20204
20213
20229
20237
20245
20257

17 with no year recorded

By model

Aircraft

See all 111 aircraft