- Effective
- November 9, 1971
- Models
- 150, 150A, 150B, 150C, 150D, 150E and 49 more
- Registered aircraft
- 41,427 matched by model
- Product
- Aircraft · Small airplane
- Amendment
- 39-1327
Unofficial copy of the text in the FAA’s Dynamic Regulatory System. The FAA’s own copy is the authoritative one. DRS record last changed May 30, 2024.
Copies of the files this page was built from, with their SHA-256. Retrieved October 18, 2026.
| File | Size | SHA-256 | Original |
|---|---|---|---|
| FAA DRS HTML | 23 KB | 7b903244…299252b | FAA DRS (API key needed) |
On this page
The airworthiness directive
71-22-02 CESSNA: Amdt. 39-1323 as amended by amendment 39-1327. Applies to 150, 172, 175 and 182 series airplanes with 1000 or more hours' time in service with earlier type nose gear fork installed but does not include the above model airplanes installed with nose gear fork bearing P/Ns 0442503-497, 0543043-497 or 0543043-498, or newer nose gear forks identified in current Cessna Parts Catalogues.
Compliance: Required as indicated, unless already accomplished.
To decrease the possibility of failure of the nose gear structure:
A) On or before January 1, 1972, and thereafter at intervals not to exceed 100 hours' time in service from the date of the previous inspection, or at any time following severe nose wheel shimmy and/or hard landings, inspect the nose gear fork for cracks in the radius of the milled section of the nose gear strut attachment bolt using the dye penetrant inspection or equivalent nondestructive inspection method.
B) If cracks are found during the inspections required by Paragraph A, before further flight, replace the affected part with applicable nose gear fork P/N 0442503-497, 0543043-497 or 0543043-498 or newer nose gear forks identified in current Cessna Parts Catalogues.
C) For those airplanes with 1500 or more total hours time in service as of January 1, 1972, and for those airplanes upon the accumulation of 1500 hours total time in service after January 1, 1972, within the first 300 hours time in service thereafter, replace earlier type forks with applicable nose gear fork P/N 0442503-497, 0543043-497, or 0543043-498 or newer nose gear forks identified in current Cessna Parts Catalogues.
D) Upon incorporation of the applicable nose gear fork P/Ns 0442503-497, 0543043-497 or 0543043-498, or newer nose gear forks identified in current Cessna Parts Catalogues, compliance with the provisions of Paragraph A are no longer required.
Cessna Service Letter 63-31 dated July 16, 1963, pertains to this same subject.Amendment 39-1323 became effective October 23, 1971.
This amendment 39-1327 becomes effective November 9, 1971.
Affected TCDS · 4
The type certificate data sheets for the models this AD names, matched by model and maker.
Registered aircraft · 41,427
Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.
| 1941 | 1 |
|---|---|
| 1943 | 1 |
| 1947 | 1 |
| 1951 | 1 |
| 1952 | 1 |
| 1953 | 1 |
| 1955 | 61 |
| 1956 | 929 |
| 1957 | 627 |
| 1958 | 952 |
| 1959 | 1,102 |
| 1960 | 871 |
| 1961 | 675 |
| 1962 | 737 |
| 1963 | 865 |
| 1964 | 1,133 |
| 1965 | 1,484 |
| 1966 | 2,081 |
| 1967 | 1,267 |
| 1968 | 1,547 |
| 1969 | 1,285 |
| 1970 | 635 |
| 1971 | 692 |
| 1972 | 1,130 |
| 1973 | 1,540 |
| 1974 | 1,362 |
| 1975 | 1,806 |
| 1976 | 1,857 |
| 1977 | 1,252 |
| 1978 | 1,118 |
| 1979 | 1,111 |
| 1980 | 616 |
| 1981 | 587 |
| 1982 | 233 |
| 1983 | 89 |
| 1984 | 139 |
| 1985 | 190 |
| 1986 | 87 |
| 1988 | 2 |
| 1994 | 1 |
| 1995 | 2 |
| 1996 | 1 |
| 1997 | 185 |
| 1998 | 434 |
| 1999 | 386 |
| 2000 | 409 |
| 2001 | 290 |
| 2002 | 227 |
| 2003 | 237 |
| 2004 | 242 |
| 2005 | 345 |
| 2006 | 250 |
| 2007 | 204 |
| 2008 | 177 |
| 2009 | 93 |
| 2010 | 76 |
| 2011 | 60 |
| 2012 | 94 |
| 2013 | 28 |
| 2014 | 84 |
| 2015 | 101 |
| 2016 | 82 |
| 2017 | 90 |
| 2018 | 64 |
| 2019 | 106 |
| 2020 | 137 |
| 2021 | 135 |
| 2022 | 138 |
| 2023 | 187 |
| 2024 | 185 |
| 2025 | 180 |
| 2026 | 146 |
5,983 with no year recorded