AD 97-15-01

97-15-01 Teledyne Continental Motors: Priority Letter issued on July 17, 1997. Docket No. 97-ANE-34-AD.

Applicability: Teledyne Continental Motors (TCM) new and rebuilt Model O-470 and IO-470 series engines with serial numbers (S/Ns) listed in Table 1 of TCM Critical Service Bulletin (CSB) No. CSB97-10, dated June 19, 1997; and TCM Model E-165, E-185, E-225, O-470 and IO-470 series engines, regardless of S/N, which have cylinder(s) with part number and purchase date as shown in Table 2 of TCM CSB No. CSB97-10, dated June 19, 1997. These engines are installed on but not limited to the following aircraft: Bellanca Models 14-19-2 and 14-19-3; Cessna Models 180, 180A through K, 182, 182A through R, 185, 185A through E, 188, 188A, 188B, 210, 210A through C, 210-5 (205), 210-5A (205A), 305A, 305C, 305D, 305F, 310, 310A through Q, E310H, E310J, 310J-1; Frontier-Aerospace, Inc. (Fletcher) Models FU-24 and FU-24A; Luscombe Aircraft Corporation Model 11A; Navion models Navion, NavionA, and Navion D through G; Prop-Jets, Inc. Models 200, 200A through C; Raytheon (formerly Beech) Models 35, A35 through P35, 35R, 35-33, 35-A355, 35-B33, 35-C33, E33, F33, 45 (YT-34), A45 (T-34A, B-45), D45(T-34B), 95-55, 95-55A, 95-B55, 95-B55A and 95-B55B; Reims models F182P and F182Q; and Twin Commander Aircraft, Inc. Model 500-A.

Note 1: This airworthiness directive (AD) applies to each engine identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For engines that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (c) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Compliance: Required as indicated, unless accomplished previously.

To prevent extreme side loading of the piston, and consequent failure of the piston and engine, accomplish the following:

(a) For the TCM O-470 and IO-470 series engines listed by S/N in Table 1 of TCM CSB No. CSB97-10 dated June 19, 1997, within 10 hours time in service (TIS) after receipt of this priority letter AD, accomplish the following:

(1) Remove from service the cylinders, six each, and the piston pins, six each, in accordance with the Inspection Instructions, Part 2A, and Appendix A of TCM CSB No. CSB97-10, dated June 19, 1997.

(2) Obtain serviceable replacement parts and reassemble the engine in accordance with the Inspection Instructions, Part 2B, of TCM CSB No. CSB97-10, dated June 19, 1997.

(b) For the E-165, E-185, E-225, series engines and those O-470 and IO-470 series engines not listed by S/N in Table 1 of TCM CSB No. CSB97-10 dated June 19, 1997, within 10 hours TIS after receipt of this priority letter AD, accomplish the following:

(1) Determine from engine log books or maintenance records if a cylinder has been replaced with a cylinder purchased in the time frames shown in Table 2 of TCM CSB No. CSB97-10, dated June 19, 1997.

(2) If a cylinder was not replaced with a cylinder purchased during those time frames listed in the CSB, or if a cylinder is identified with the letter "M" or "P" steel stamped after the cylinder position number, as cylinders marked with "M" or "P" have a surface finish that has been found to be within specification, no further action is required. The cylinder position number is located at the 12 o'clock position on the cylinder mounting flange.

(3) If a cylinder has been replaced with a cylinder purchased during those time frames listed in the CSB, remove from service the affected cylinders and piston pins in accordancewith the Inspection Instructions, Part 2A, and Appendix A of TCM CSB No. CSB97-10, dated June 19, 1997.

(4) Obtain serviceable replacement parts and reassemble the engine in accordance with the Inspection Instructions, Part 2B, of TCM CSB No. CSB97-10, dated June 19, 1997.

(c) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Atlanta Aircraft Certification Office. Operators shall submit their requests through an appropriate FAA Maintenance Inspector, who may add comments and then send it to the Manager, Atlanta Aircraft Certification Office.

Note 2: Information concerning the existence of approved alternative methods of compliance with this airworthiness directive, if any, may be obtained from the Atlanta Aircraft Certification Office.

(d) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14CFR 21.197 and 21.199) to operate the aircraft to a location where the requirements of this AD can be accomplished.

(e) Copies of the applicable service information may be obtained from Teledyne Continental Motors, P.O. Box 90, Mobile, AL 36601; telephone (334) 438-3411. This information may be examined at the FAA, New England Region, Office of the Assistant Chief Counsel, 12 New England Executive Park, Burlington, MA.

(f) Priority Letter AD 97-15-01, issued July 17, 1997, becomes effective upon receipt.