ATL06LA028

The pilot was in cruise flight at 2,000 feet AGL. The engine did not appear to be producing full power. The pilot reversed his course back towards the departure airport. The engine oil pressure decreased to zero and the engine lost power. The pilot made an emergency landing to none suitable terrain, and the airplane received substantial damage on the landing roll out. The engine was disassembled. The No.1 cylinder was removed and the No.1 connecting rod was bent and separated from the crankshaft journal. The No.1 connecting rod, piston, and oil suction debris were forwarded to the NTSB Materials Laboratory for further examination. The examination revealed a failure of the No.1 connecting rod bearing.

History of flight

On December 27, 2005, at 1715 eastern standard time, a Cessna 177-RG, N53257, registered to a private owner, operating as a 14 CFR part 91 personal flight, reported a total loss of engine power, and collided with the ground during an emergency landing in the vicinity of Locust Grove, Georgia. Visual meteorological conditions prevailed and no flight plan was filed. The airplane received substantial damage. The commercial pilot reported minor injuries, and one passenger received serious injuries. The flight originated from Clay County-Tara Field, Hampton, Georgia, on December 27, 2005, at 1700.

The pilot stated he departed Tara Field from runway 24, and climbed to 2,000 feet AGL, enroute to Mallards Landing. While in cruise flight at 2,000 feet AGL, the engine did not appear to be producing power. The engine RPM gauge indicated 2,300 RPM and the manifold pressure gauge indicated 22-inches. The pilot stated he had to increase the pitch attitude of the airplane to maintain level flight. The pilot reversed his course and flew back towards Tara Field. The engine oil pressure decreased to zero, and the engine quit. The propeller appeared to seize and stopped. The pilot declared an emergency on Tara Field UNICOM radio frequency, and realized he could not make the airport. The pilot observed an open field to his left and initiated an emergency landing to the field. The airplane touched down on the main landing gear. The landing area was wet, soft, and muddy with holes and depressions. The nose gear touched down and the airplane came to an abrupt stop with about a 60 foot long ground roll. The pilot and the passenger exited the airplane. Examination of the airplane revealed the airframe had received structural damage.

Personnel information

Review of information of file with FAA Airman's Certification Division, Oklahoma City, Oklahoma, revealed the pilot was issued a commercial pilot certificate on July 13, 2004, with ratings for airplane single engine land and instrument airplane. The pilot's last flight review was conducted on July 13, 2004. The pilot holds a second class medical certificate issued on April 25, 2005, with the restriction, "must wear corrective lenses." The pilot reported on the NTSB Pilot/Operator Aircraft Accident/Incident Report that he has accumulated 575 total flight hours with 258 hours in the PA32-300.

Aircraft information

Review of the airplane log books revealed the last recorded annual inspection was conducted on December 17, 2004, and the airplane has flown 190 hours since the annual inspection. The total time on the engine is 4,070 hours, and the time since overhaul is 1,475.The airframe has a total of 9,190 hours at the time of the accident. The tachometer at the time of the engine examination by the NTSB was 2615.9 hours.

Meteorological information

The William B. Hartsfield Atlanta International Airport, Atlanta, Georgia, 1751 eastern standard time surface weather observation was: wind 210 degrees at 13 knots, visibility 8 miles, overcast clouds at 13,000 feet, temperature 52 degrees Fahrenheit, dew point temperature 45 degrees Fahrenheit, and altimeter 30.00.

Wreckage and impact information

Examination of the cabin area was conducted at an aircraft recovery facility. The fuel selector was found in the both position. The throttle was one-eighth of an inch from the idle stop on the fuel servo and the throttle cable moved freely by hand. The throttle cable was damaged and could not be moved through its full range. The propeller was in low rpm high pitch and the throttle cable moved freely by hand through its complete range. The mixture cable was one-fourth of an inch from the idle cut off stop on the fuel servo and was extended one and one half inches in the cabin area. The mixture cable moved freely by hand through its complete range.

The left and right main fuel tanks were not ruptured and 30 gallons of 100-low lead fuel was removed from the right main fuel tank. Air was blown through the main fuel tank vent interconnect fuel system and continuity of the vent system was confirmed. Air was blown into the left main fuel tank feed line and air was observed coming out of the right main fuel tank feed line. Air was also observed coming out of the right reservoir fuel tank vent line. In addition, fuel was observed coming from the left fuel tank reservoir fuel tank vent line. The fuel strainer was drained by pulling the drain lever and fuel was observed draining from the strainer. The fuel strainer bowl was removed from the strainer assembly. No contaminants were observed in the fuel strainer bowl or fuel screen. Air blown into the left main fuel tank inlet port and fuel was observed exiting the fuel strainer. Fuel was present in the fuel injector lines going to the No.1 cylinder. Fuel was present in the fuel line from the engine driven fuel pump to the fuel servo. The fuel pressure gage line was disconnected and fuel was present. The fuel pump was removed and the fuel was present in the inlet, and pumping action was observed when the fuel pump actuated by hand. The flow divider was removed and disassembled. The diaphragm was intact and fuel was present. All fuel nozzles were removed and not obstructed. The fuel servo was removed and fuel was present in the fuel servo. The fuel servo screen was free of contaminants.

The engine assembly was displaced downward and to the left. The right upper engine mount, lower left and right engine mount remained attached to the firewall. The engine inlet air box was crushed upward. The propeller assembly remained attached to the crankshaft flange. The propeller spinner was crushed. One propeller blade was intact and not damaged. The remaining propeller blade was bent aft about 20-degrees approximately 8-inches outboard of the propeller hub, and the propeller blade was loose in the propeller hub.

All engine accessories remained attached to the engine and were not damaged. All fuel and oil lines remained attached. The top spark plugs and rocker covers were removed and exhibited "worn out normal" when compared to the Champion Check A Plug chart. The engine was rotated by hand and continuity to the rear engine gears and valve train was observed. Compression and suction was observed on cylinder 2, 3, and 4. No compression and suction was observed on cylinder No.1 and the piston could not be observed to move up and down inside the cylinder. The bottom spark plugs were removed and exhibited "worn out normal" when compared to the Champion Check A Plug chart. The No.1 bottom spark plug was oil soaked. The engine oil indicated six quarts of oil on the dipstick. The oil suction screen was removed from the oil sump and contained silver colored metallic flakes. The oil filter was removed and opened. The oil filter element contained silver colored metallic flakes. The vacuum pump was removed and disassembled. The carbon rotor and vanes were intact, and the drive rotated freely when turned by hand. The magneto was removed and spark was noted at all ignition towers when the magneto drive was turned by hand. The oil cooler was not damaged and all connections were tight.

The No.1 cylinder was removed and the No.1 connecting-rod was bent and separated from the crankshaft journal. The rod bolts remained attached to the rod and the rod separated in three pieces. The No.1 piston was free to move in the cylinder and all piston rings were stuck in the ring grooves. The No. 2, 3, and 4 cylinders were removed and the valves were not damaged. The piston domes were not damaged and all piston skirts were scored and scuffed. The piston rings were free in the ring groves. The engine case halves were separated. The camshaft was not damaged. The crankshaft main bearings were not damaged. The No. 2, 3, and 4 rod bearings were scored and exhibited extrusions of the bearing material. The crankshaft was intact. The main bearing journal was not damaged. The No.1 rod-bearing