LAX99LA284

The pilot reported that a linesman directed him toward the center one of three transient parking helipads next to a small perimeter fence. All three helipads were empty. As he approached the pad, the pilot became concerned about obstructions and about exposing his tail rotor to a taxiway beyond his view. He performed a left pedal turn over the pad to bring the nose around to face the taxiway. He reported that the linesman made a 'hands-down motion' and walked away. The pilot assumed he was clear to touchdown. As he touched down, the tail rotor contacted the helipad's perimeter fence. The nose of the helicopter yawed left and the pilot performed a hovering autorotation. The tail rotor blades were destroyed and the tail boom was buckled. The distance from the center of the helipad parking space to the fence was measured at 23 feet. The distance from the main rotor mast to the end of the tail stinger on the AS350B3 is just over 23 feet. According to the parking space requirements outlined by FAA A/C 150/5390-2A, the fence was supposed to be no closer than 10 feet to any part of the helicopter. The fence was found to be within the tail rotor clearance area specified in the Advisory Circular. There was insufficient room for the helicopter to make a 180-degree turn, assuming it stayed on the center point of the parking space.

On August 26, 1999, at 1333 hours Pacific daylight time, an Aerospatiale AS350B3, N5224R, collided with a fence while landing at the Long Beach, California, airport. The helicopter, operated by American Eurocopter, Grand Prairie, Texas, was substantially damaged. The commercial pilot and commercial rated passenger were not injured. The local area business flight was conducted under the provisions of 14 CFR Part 91 and originated from the Van Nuys, California, Airport, about 1235, and made a planned stop at a private heliport in Los Angeles before continuing to Long Beach. Visual meteorological conditions prevailed and no flight plan was filed.

In a written statement, the pilot reported that he had planned to park the helicopter on a pad in front of a fixed-base operator (FBO). He reported that the air traffic controller directed him to land on runway 7 and air taxi to the FBO. Upon reaching the FBO's ramp, a linesman directed the pilot toward the center of three helipads next to a small fence that bordered the western perimeter of the ramp. All three pads were empty. The pilot reported that as he approached the pad he became concerned that his tail rotor was exposed to a taxiway which was out of his view. Additionally, there were two large semi-tractor trailers parked south of the helipad which the pilot felt would obstruct the view of any aircraft taxiing out of the south end hangar. Because of these obstructions, the pilot initiated a left pedal turn over the pad to bring the nose of the helicopter around to face the taxiway. The pilot reported that he looked to the linesman for further landing guidance. The linesman made a "hands-down motion" and started to walk away. The pilot stated that he interpreted the linesman's signal to mean that he was clear to touchdown. As he landed, he felt a slight impact followed by a series of vibrations. The nose of the helicopter began to yaw left. The pilot reported that he immediately lowered the collective and reduced the power; he had no tail rotor control at that time.

The pilot instructed his passenger to remain in the helicopter until he could ensure that the area was clear. He performed a normal engine shutdown. As he exited the helicopter, he discovered that the tail rotor had struck the short chain link fence behind the aircraft. The tail rotor blades were destroyed and about 3 inches of the blade tips were broken off. One piece impacted the exhaust stack and went into the engine. The tailboom was buckled.

A representative from American Eurocopter submitted a drawing of the helipad displaying the measurements of the perimeter and the pad's location in relation to the fence. The pad, as defined by the painted border stripes, was 36 feet by 35 feet, which would generate a radius comparable to approximately 17 1/2 feet. The distance from the center of the "H" to the fence line was shown as 23 feet, and the distance from the nearest pad border of the helipad to the fence was 5 1/2 feet. According to American Eurocopter, the main rotor diameter of the AS350B3 helicopter is 35 feet and the distance from the center of the main rotor mast to the end of the tail stinger is just over 23 feet.

The parking space dimensions were reviewed for compliance with Federal Aviation Administration (FAA) Advisory Circular (AC) 150/5390-2A, issued in 1994. The application of the measurements to the FAA criteria revealed that the fence, at 23 feet from the center point of the helicopter parking space, was within the tail rotor clearance area. Pertinent portions of the Advisory Circular and the helicopter dimensions are appended to this file.