TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '7c305c77a46e598af8652dcae55f1fadd480f021356881c395f1ee07b7658eff' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '7c305c77a46e598af8652dcae55f1fadd480f021356881c395f1ee07b7658eff' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
AIR TRACTOR, INC.
OLNEY, TEXAS
ENGINEERING NUMBER #347 REPORT Revision A
ORDER X MODEL TITLE BY CHK’D See Below SERVICE LETTER #347
Jim Hirsch DL
SERIAL DATE See Below
PAGE OF 12/9/19 1 3
Rev IR – 6/10/16 – Initial Release Rev A – 12/9/19 – Added visual and dye penetrant recurring inspections
1. SUBJECT
Flap Torque Tube
2. MODELS AND SERIAL NUMBERS
All Air Tractor Models
3. SAFETY INTENT
We have received multiple reports of cracks in the flap actuator attach plates on the flap torque tube on various Air Tractor models. In two cases, the flap actuator attach plates separated completely and the flaps suddenly retracted while maneuvering. In both cases, the pilot temporarily lost control of the plane, but was able to regain control before the plane impacted the ground. The intent of this service letter is to warn the operator of the possibility of these cracks and to provide inspection instructions and intervals per Section 4 below. Also see Figure 1.
4. ACTION
A. At 300 hour (± 15%) intervals, perform a visual inspection for cracks in the flap torque tube per the following instructions.
(1) Remove the side skins adjacent to the cockpit as necessary to gain access to the flap torque tube.
(2) Before inspecting the torque tube welds, inspect the general condition of the flap control system. Make sure that the system is operating properly and that the flap travel is correct. See Owners Manual for travel limits and tolerances. Make sure that there is no binding or rubbing in the system. Pay special attention to the right and left flap control arm push rod attach bolts ensuring that they pass the inboard wing skins without rubbing or hanging up.
(3) Clean the welds to remove dirt and debris that would interfere with the inspection. Using a light and mirror, visually inspect the flap actuator attach plate welds for cracks. Use FAA AC 43.13 Chapter 5 Section 2 “Visual Inspections” to accomplish the visual inspection.
(4) If cracks are found, remove and replace the flap torque tube.
(5) Record in the airframe logbooks the results of this inspection and that it was performed “per SL 347 Rev. A”.
AIR TRACTOR, INC.
OLNEY, TEXAS
ENGINEERING NUMBER #347 REPORT Revision A
ORDER X MODEL TITLE BY CHK’D See Below SERVICE LETTER #347
Jim Hirsch DL
SERIAL DATE See Below
PAGE OF 12/9/19 2 3
B. At 900 hour maximum intervals, perform a dye penetrant inspection for cracks in the flap torque tube per the following instructions. If the currently installed flap torque tube has accumulated more than 900 hours total time upon receipt of this Service Letter, perform this inspection at next 300 hour inspection.
(1) Complete steps (1) and (2) from Section A above.
(2) It is necessary to remove the flap torque tube from the aircraft to complete the dye penetrant inspection. Depending on airplane configuration, remove any components necessary to gain access to the torque tube.
(3) To remove the torque tube, remove the flap actuator as instructed in the Owners Manual Maintenance Section. Remove the two flap control push rods and arms from the ends of the torque tube. Remove the limit micro switch actuating arm.
(4) Remove the cable tensioner push rod. (AT-802, AT-802A only)
(5) Remove the bolts that attach the torque tube to the links in the aileron control system. AT-802 and AT-802A do not have these.
(6) Remove the bolts that attach the torque tube to the lower longeron on both sides and remove the torque tube from the plane.
(7) Perform a dye penetrant inspection using the methods detailed in FAA Advisory Circular 43.13 Chapter 5 Section 5 “Penetrant Inspection”. The paint must be removed from the weld area prior to performing the penetrant inspection. Dye Penetrant Types I, II, or III may be used for this inspection, but note that some penetrant types are not compatible with others (See FAA Special Airworthiness Bulletin (SAIB) CE-18-26).
(8) If cracks are found in any weld area, the torque tube must be replaced.
(9) If no cracks are found, thoroughly clean all dye penetrant from the torque tube with naptha, wipe clean, and then blow dry any crevices with compressed air.
Repaint the bare metal areas with paint products listed in the Owners Manual.
Once dry, reinstall the torque tube and all disturbed parts/systems.
(10) Inspect the area thoroughly to ensure proper installation and adjustment and perform any functional checks necessary to ensure proper operation of any system that may have been affected by this inspection.
(11) Record in the airframe logbooks the results of this inspection and that it was performed “per SL 347 Rev. A”. Also record what type of dye penetrant was used in this inspection. (Type I – Fluorescent Dye, Type II – Visible Dye, Type III – Dual Mode Visible and Fluorescent Dye).
Please report any cracked weld on the flap torque tube to the Customer Service Department at Air Tractor. (940-564-5616)
AIR TRACTOR, INC. ENGINEERING NUMBER #347 OLNEY, TEXAS REPORT Revision A
ORDER MODEL TITLE BY CHK'D See Below SERVICE LETTER #347 Jim Hirsch DL SERIAL DATE See Below
PAGE OF 12/9/19 3 3
- FLAP TORQUE TUBE
EXAMPLE CRACK LOCATION
- INSPECT WELDS FOR CRACKS FIGURE 1. FLAP TORQUE TUBE INSPECTION