Service bulletin · Eurocopter

Revision 1U.S. DOT/FAA - Eurocopter ASB No 67A007 Rev 1 · 10 pages · 205 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0464; AD 2015-11-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2014-0464 (document 0004) · AD 2015-11-06

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Alert Service Bulletin
Number
67A007
Latest revision known
67A007, Revision 1, dated February 25, 2009

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 2

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 2 proposed ADs.

Text · 10Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0464; AD 2015-11-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '135f7c7bde9c189b84563f93a9ccdb4db3e411c787d6c2d09760c32b9565f958'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 1/10 2009.02.25

This document is available on the internet: www.eurocopter.com/techpub

EUROCOPTER

DIRECTION TECHNIQUE SUPPORT 13725 MARIGNANE CEDEX FRANCE CIVIL VERSION(S): B, B1

ALERT SERVICE BULLETIN

No. 67A007

SUBJECT: ROTOR FLIGHT CONTROLS

Check of the Collective Pitch Lever Restraining Tab

REVISION No.

DATE OF APPROVAL

DATE OF ISSUE

Revision 0 On: January 20, 2006 2006.01.20 Revision 1 On: February 23, 2009 2009.02.25

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 2/10 2009.02.25

CAUTION

THE INFORMATION AND INSTRUCTIONS CONTAINED IN

THIS ALERT SERVICE BU LLETIN ARE INTENDED FOR

MAINTENANCE PERSONNEL AND FLIGHT CREWS

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/Installed equipment

- Helicopters fitted with the collective pitch lever "low pitch" locking system and not modified per MOD 0767B65.

NOTE

MOD 0767B65 is introduced by Service Bulletin No. 67-009.

Refer to the aircraft individual inspection record (MOD record), or the aircraft log book to identify the actual configuration of the helicopter.

1.A.2. Non-installed equipment: Not applicable.

1.B. ASSOCIATED REQUIREMENTS

Not applicable.

1.C. REASON

- To prevent the risk of:

. untimely collective pitch lever locking, when the collective pitch lever is moved to the "low-pitch" position, . untimely collective pitch lever unlocking during engine starting.

- Revision 0 of this ALERT SERVICE BULLETIN formed the subject of Revision 1 of Airworthiness Directive No. F-2005-127 issued by the DGAC on behalf of the EASA.

- Revision 0 of this ALERT SERVICE BULLETIN:

. superseded ALERT TELEX No. 67A007, dated June 30, 2005, . modified paragraphs 2.B.2., 2.B.3. and 3.C.3. and Detail B on Figure 1, with no change to the technical content:

- specifying the various types of spring scales to be used: “pull type” spring scale (1) or “push type" spring scale (3),

- providing additional information concerning the use of the “pull type” spring scale (NOTE in paragraph 2.B.2.).

- Revision 1 of this ALERT SERVICE BULLETIN informs the users that helicopters modified per MOD 0767B65 (introduced by Service Bulletin No. 67-009) are not concerned by the instructions of this ALERT SERVICE BULLETIN.

- Revision 1 of this ALERT SERVICE BULLETIN will form the subject of a new EASA Airworthiness Directive.

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 3/10 2009.02.25

1.D. DESCRIPTION

One of our operators has discovered two problems on the collective pitch lever locking system:

- One case of untimely locking of the collective pitch lever, which occurred in flight, when moving the collective pitch lever to the "low pitch" position: The reason for this occurrence is attributed to an anomaly concerning the shape of the restraining tab.

- One case of untimely unlocking of the collective pitch lever during engine starting.

When the collective pitch lever is in the locked configuration, it should apply a minimum upward load to ensure that the restraining tab remains locked to the collective pitch lever. If this load is too low (in the event of incorrect adjustment), there is a risk of unwanted collective pitch lever unlocking.

In view of the elements outlined above, EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory.

1.E. COMPLIANCE

The following measures are mandatory since receipt of ALERT TELEX No. 67A007, issued on June 30, 2005.

1.E.1. Compliance at the works

1.E.1.a. On helicopters/installed equipment: Before delivery, comply with paragraph 2. of this ALERT SERVICE BULLETIN.

1.E.1.b. Non-installed equipment: Not applicable.

1.E.2. Compliance in service: By the operator

1.E.2.a. On helicopters/installed equipment: Comply with paragraph 2. within the 50 flying hours following receipt of ALERT TELEX No. 67A007, issued on June 30, 2005

1.E.2.b. Non-installed equipment: Not applicable.

1.F. APPROVAL

Approval is limited to civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in Revision 0 of this ALERT SERVICE BULLETIN No. 67A007 was approved on January 20, 2006 under the authority of EASA Design Organisation Approval No. 21J.056.

The technical information contained in Revision 1 of this ALERT SERVICE BULLETIN No. 67A007 was approved on February 23, 2009 under the authority of EASA Design Organisation Approval No. 21J.056.

1.G. MANPOWER

Qualification: 1 mechanic.

Time: Approximately 1 hour.

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 4/10 2009.02.25

1.H. WEIGHT AND BALANCE

Weight: Not applicable.

Moment: Not applicable.

1.I. EFFECT ON ELECTRICAL LOADS

Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT STATE

Not applicable.

1.K. REFERENCES

- Aircraft Maintenance Manual (AMM):

Tasks: 24-00-00-481, 24-00-00-911, 29-00-00-911, 29-12-00-481.

1.L. OTHER DOCUMENTS CONCERNED

Aircraft Maintenance Manual (AMM).

Maintenance Program (MSM).

1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS

Not applicable.

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 5/10 2009.02.25

2. ACCOMPLISHMENT INSTRUCTIONS

2.A. GENERAL

- Comply with the electrical power general instructions as per AMM, Task 24-00-00-911.

- Comply with the hydraulic power general instructions as per AMM, Task 29-00-00-911.

2.B. OPERATIONAL PROCEDURE

2.B.1. Preliminary steps

- Pressurize the hydraulic power system as per AMM Task 29-12-00-481.

- Energize the aircraft electrical power system as per AMM Task 24-00-00-481.

2.B.2. Check focused on the risk of collective pitch lever (C) unlocking (Figure 1 - Detail B)

- Lock the collective pitch lever (C).

- Using a “pull type” spring scale (1) or a “push type” spring scale (3), measure the load "G" required to unlock the pilot's collective pitch lever (C).

NOTE

If you use a “pull type” spring scale (1), it shall be kept slightly away from the console to be able to measure the load “G”.

- If the collective pitch lever (C) unlocks at:

. a load 11 < G < 14 daN, the adjustment is correct:

- comply with paragraph 2.B.4., . a load "G" outside the range above, the adjustment is incorrect:

- comply with paragraph 2.B.3.

2.B.3. Adjustment of collective pitch lever (C) unlocking (Figure 1 - Detail B)

- Adjust the restraining tab (F) using the oblong holes, in such a way that the collective pitch lever (C) unlocks at a load 11 < G < 14 daN, measured using a “pull type” spring scale (1) or a “push type” spring scale (3).

- Comply with paragraph 2.B.4.

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 6/10 2009.02.25

2.B.4. Check focused on the risk of unwanted locking (Figure 1 - Detail A)

- Set the collective pitch lever to the "low pitch" position and hold it in this position, without forcing downwards.

- Tighten the friction lock.

- Check the clearance "J1" between the locking pin of the collective pitch lever (C) and the L-section of the restraining tab (F).

. If J1 > 3 mm, the adjustment is correct:

- loosen the friction lock,

- return the helicopter to its original configuration in compliance with paragraph 2.B.6.

. If J1 < 3 mm, the adjustment is incorrect:

- loosen the friction lock,

- modify the shape of the restraining tab (F) in compliance with paragraph 2.B.5.

2.B.5. Modifying the shape of the restraining tab (F) (Figure 1)

CAUTION

DO NOT UNBEND THE RESTRAINING TAB (F) AFTER HAVING BENT IT.

- Identify the position of the restraining tab (F) on the console so that it can be re-installed at the same location after removal.

- Remove the restraining tab (F): screws (D), washers (E), Detail A.

- On a workbench:

. Clamp the restraining tab (F) in a vice (2) fitted with soft jaws, as shown on Detail K.

. Gradually apply a load "H" to the restraining tab (F) (Detail K), until it is lightly distorted, in order to ensure a clearance J1 > 3 mm, on the helicopter.

- Install the restraining tab (F) at the position previously identified: screws (D), washers (E), Detail A.

. If J1 > 3 mm, the adjustment is correct:

- comply with paragraph 2.B.2., to ensure that the load "G" is still within the 11 to 14 daN range.

. If J1 < 3 mm, further distort the restraining tab (F) in the vice (2).

2.B.6. Final steps

- De-energize the aircraft electrical power system as per AMM Task 24-00-00-481.

- Cut the hydraulic power supply of the helicopter as per Task 29-12-00-481.

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 7/10 2009.02.25

2.C. IDENTIFICATION

Record compliance with this ALERT SERVICE BULLETIN in the aircraft documents.

2.D. OPERATING AND MAINTENANCE INSTRUCTIONS

2.D.1. Operating instructions: Not applicable.

2.D.2. Maintenance instructions:

A routine check to be carried out in addition to t he current maintenance will be incorporated in the Aircraft Maintenance Manual (AMM) and in the Maintenance Program (MSM) through a Revision.

Page 8OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC155 K A-B Figure 1: Collective pitch lever and restraining tab Approved under EASA DOA No. 21J.056. 67A007 Page 8/10 2009.02.25

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 9/10 2009.02.25

3. MATERIAL INFORMATION

3.A. MATERIAL: COST - AVAILABILITY

For any information concerning kits and/or components, contact the Sales and Customer Relations Department of the EUROCOPTER Network.

3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT

Not applicable.

3.C. MATERIAL REQUIRED FOR EACH AIRCRAFT, ENGINE/COMPONENTS

3.C.1. Component(s)

Not applicable.

3.C.2. Items to be ordered separately

Not applicable.

The materials identified by an asterisk "*" or required for compliance with the tasks and/or work cards listed in paragraph 1.K., can be ordered from the INTERTURBINE company, Website: http://www.itlogistics.de Phone: +49.41.91.809.300 AOG: +49.41.91.809.444

3.C.3. Tooling

Part Number Qty Item Key Word

/

/ A/R

A/R 1

3 “Pull type” spring scale or “Push type” spring scale

ALERT SERVICE BULLETIN EC155 Approved under EASA DOA No. 21J.056. 67A007 Page 10/10 2009.02.25

3.D. MATERIAL REQUIRED FOR EACH SPARE PART

Not applicable.

3.E. RE-IDENTIFIED PARTS

Not applicable.

3.F. TOOLING: COST – AVAILABILITY

Not applicable.

3.G. PROCUREMENT CONDITIONS

Order the required quantity (unless otherwise specified)

from

EUROCOPTER Etablissement de Marignane Direction Ventes et Relations Client ECR 13725 MARIGNANE CEDEX FRANCE

NOTE 1

For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4 42 85 99 96.

NOTE 2

On the purchase order, please specify the mode of transport, the destination and the serial numbers of the aircraft to be modified.

4. APPENDIX

Not applicable.