Service bulletin · Airbus Helicopters

Revision 1Airbus Helicopters ASB BO105-80A-150 Rev 1 · 11 pages · 580 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0308, the docket of AD 2021-13-14. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2021-0308 (document 0004) · AD 2021-13-14

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
BO105-80A-150
Latest revision known
BO105-80A-150, Revision 1

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 11OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0308, the docket of AD 2021-13-14. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '2219bfea8302837e36a7f57abb5994d07cf55d739a20d5289136d860ae720894'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150 Valid for version (s): C (C23, CB, CB-3, CB-4, CB-5), D (DB, DBS, DB-4, DBS-4, DBS-5), • S (CS, CBS, CBS-4, CBS-5)

ALERT SERVICE BULLETIN SUBJECT: OPTIONAL EQUIPMENT - Rescue Hoist Deactivation of the cable cutter function on the control grip For the attention of Revision number Issue date Revision 0 2014-10-27 Revision 1 2015-02-02 Summary:

A design review on the BO105 showed, that a failure in the harness of the rescue hoist control grip could cause an unintentional actuation of the cable cutter function.

Reason of Revision:

With Revision 1 the deactivation of the cable cutter on the BO105 control grip is prescribed.

Compliance:

Compliance with this Alert Service Bulletin is mandatory.

Revision 1, 2015-02-02 PAGE 1 of 11 This document is available on the internet: www.airbushelicopters.com/techpub

Page 2OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150 1 PLANNING INFORMATION

1.A EFFECTIVITY

1.A.1 Helicopters/installed equipment B0105, C, D and S (all variants) with optional equipment rescue hoist.

1.A.2 Non-installed equipment Not applicable.

1.B ASSOCIATED REQUIREMENTS The pilots of the BO105 must be informed of the content of this Alert Service Bulletin immediately after its accomplishment and they must be told that the procedures i.a.w.

temporary revision of the flight manual must be respected:

BO105 C/CS TempRev 1 BO105 CB/CBS TempRev 1 BO105 CB-5/CBS-5 TempRev 1 BO105 DB/DBS TempRev 1 BO105 DBS-5 TempRev 1

1.C REASON During a flight with a MBB-BK117 an unintentional actuation of the cable cutter function occurred when the rescue winch was operated. The reason for this actuation was an electrical malfunction caused by mechanical damage to the coiled cable between helicopter and control grip. Based on this event, a design review on the B0105 was conducted and concluded, that a similar failure mechanism is also applicable for the BO105 control grip harness. With Revision 1 the deactivation of the cable cutter on the B0105 control grip is prescribed.

1.D DESCRIPTION Inspect control grip with coiled cable. Disconnect concerned wires and cap and stow them. Affix placard "INACTIVE". Check the deactivation of the cable cutter function on the control grip.

1.E COMPLIANCE

1.E.1 Compliance at the works Helicopters/installed equipment:

Not applicable.

Non-installed equipment:

Not applicable.

PAGE 2 of 11 Revision 1, 2015-02-02 This document is available on the internet: www.airbushelicopters.com/techpub

Page 3OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150

1.E.2 Compliance in service Helicopters/installed equipment:

EFFECTIVITY If Revision O has not been accomplished:

a) Inspect the control grip with coiled cable i.a.w. Section 3.B.1.1 of this Alert Service Bulletin before the next mission with rescue winch.

- If a damaged control grip / coiled cable is detected, replace the damaged part with a serviceable part before the next mission with rescue winch.

EFFECTIVITY All:

a) A visual check of the control grip (with coiled cable) for condition has to be performed in the frame of the preflight check. This check can be performed by the pilot.

b) Deactivate the cable cutter function on the control grip i.a.w. Section 3.B.1.2 of this Alert Service Bulletin.

- The cable cutter function must be deactivated by February 10, 2015 at the latest.

- Inform the pilots of the BO105 about the deactivation of the cable cutter function on the control grip.

In the future, inspect every 30 days (tolerance +10%) the control grip with coiled cable i.a.w. Section 3.B.1.1 of this Alert Service Bulletin for mechanical damage.

- If a damaged control grip / coiled cable is detected, replace the damaged part with a serviceable part before the next mission with rescue winch.

d) This Alert Service Bulletin introduces a TBO of 10 years for the control grip with coiled cable. If the deadline for the first TBO has already been exceeded upon receipt of this Alert Service Bulletin the operator is granted a time period of 9 months to accomplish the next TBO.

Non-installed equipment:

Not applicable.

1.F APPROVAL Approval of this document:

The technical content of this document is approved under the authority of DOA No. EASA.21J.034.

1.G MANPOWER Not applicable.

Revision 1, 2015-02-02 PAGE 3 of 11 This document is available on the internet: www.airbushelicopters.com/techpub

Page 4OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150

1.H WEIGHT AND BALANCE Not applicable.

1.l EFFECT ON ELECTRICAL LOADS Not applicable.

1.J SOFTWARE MODIFICATION EMBODIMENT RECORD Not applicable.

1.K REFERENCES MM B0105.

WDM B0105.

1.L DOCUMENTS AFFECTED The necessary procedures which are required as a result of this Alert Service Bulletin are described in the temporary revision of the flight manual (see Section 3.D).

The changes to the maintenance manual MM BO105 which are required as a result of this Alert Service Bulletin will be incorporated with the next revision (see Section 3.D).

1.M INTERCHANGEABILITY OR MIXABILITY OF PARTS Interchangeability:

Not applicable.

Mixability:

Not applicable.

PAGE 4 of 11 Revision 1, 2015-02-02 This document is available on the internet: www.airbushelicopters.com/techpub

Page 5OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150 2 MATERIAL INFORMATION

2.A MATERIAL: PRICE - AVAILABILITY - PROCUREMENT Information on price and availability of required retrofit kit SB-105-80A-150-2C will be provided by Airbus Helicopters Deutschland, Dept. Spares Order Administration on request.

2.B INFORMATION CONCERNING INDUSTRIAL SUPPORT Not applicable.

2.C MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT Kits or components to be ordered for one helicopter:

Retrofit kit SB-105-80A-150-2C.

No. Keyword Units New P/N Old P/N Remark Placard INACTIVE L311M3500324 Z.D MATERIAL TO BE RETURNED Not applicable.

Revision 1, 2015-02-02 PAGE 5 of 11 This document is available on the internet: www.airbushelicopters.com/techpub

Page 6OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150

ACCOMPLISHMENT INSTRUCTIONS З.А GENERAL Not applicable.

З.В OPERATIONAL PROCEDURE

3.B.1 Procedure

3.B.1.1 Inspect control grip with coiled cable (Figure 1) for mechanical damage:

a) Inspect control grip for mechanical damage such as deformed or damaged switches or a damaged housing.

- If a damaged control grip is detected, replace the damaged control grip with a serviceable part before the next mission with rescue winch.

b) Inspect coiled cable of the control grip for mechanical damage such as abrasion, cracks, cuts and other kinds of damage. If necessary, use aids such as a flashlight or a magnifying glass.

- If a damaged coiled cable is detected, replace the damaged coiled cable with a serviceable part before the next mission with rescue winch.

3.B.1.2 Deactivation of the cable cutter function on the control grip:

a) Unscrew and remove screws of overhead panel (lower part, see Figure 1).

b) Disconnect plug of control grip on receptacle 25VEA. Remove control grip with coiled cable.

c) Disconnect wire MF3M20 of receptacle 25VEA, contact "F" (see wiring diagram, Figure 2). Cap and stow the wire, for this purpose slide heat-shrinkable sleeve onto the contact of the wire end and shrink with hot air blower. Whenever necessary, fix capped and stowed wire to existing wires using lacing tape.

d) Disconnect wire MF4E22 of receptacle 25VEA, contact "G" and wire MF6E20 of receptacle 25VEA, contact "H". Cut the contacts at wire end. Strip both wire ends and crimp with butt splice (see wiring diagram, Figure 2). The wire connection is necessary to guarantee the test function.

e) Install overhead panel (lower part, see Figure 1) with screws.

f) Connect plug of control grip to receptacle 25VEA.

g) Degrease the place to be bonded (see Figure 1) on the circlip of switch CABLE CUTTER on the control grip and affix placard "INACTIVE" using a transparent adhesive silicone (e.g. CM 674) (see Figure 1).

PAGE 6 of 11 Revision 1, 2015-02-02 This document is available on the internet: www.airbushelicopters.com/techpub

Page 7OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150

3.B.2 Tests

3.B.2.1 Check the deactivation of the cable cutter function on the control grip.

a) Unscrew cap or plug 132VVa from receptacle 132VV (AIRFRAME, WINCH ARM).

b) Connect multimeter to receptacle 132VV (see WDM B0105) with suitable adapter as follows:

- "+" on contact "F"

- "" on contact "G"

- Preselect measuring mode "Volt".

c) Connect and switch on external power supply.

d) Press circuit breaker CABLE CUTTER on instrument panel.

e) Set WINCH MAIN SWITCH on the overhead panel to position ON.

f) Press switch CABLE CUTTER on the pilot's collective lever:

- Measured value on multimeter: approx. 28VDC (helicopter voltage)

g) Release switch CABLE CUTTER on the pilot's collective lever:

- Measured value on multimeter: approx. 0 VDC

h) Connect control grip to receptacle 25VEA on the overhead panel.

i) Press switch CABLE CUTTER on the control grip:

- Measured value on multimeter: approx. O VDC

j) Release switch CABLE CUTTER on the control grip:

- Measured value on multimeter: approx. 0 VDC

k) Switch off external power supply.

I) Remove multimeter from receptacle 132VV.

m) Screw cap or plug 132VVa to receptacle 132VV.

З.С IDENTIFICATION Accomplishment of the steps described in this document:

Confirm accomplishment of this Alert Service Bulletin by an entry in the historical record of the helicopter.

Revision 1, 2015-02-02 PAGE 7 of 11 This document is available on the internet: www.airbushelicopters.com/techpub

Page 8OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150

3.D OPERATING- AND MAINTENANCE INSTRUCTIONS Flight Manual:

The pilots of the B0105 must be informed of the content of this Alert Service Bulletin immediately after its accomplishment and they must be told that the procedures of the temporary revision of the flight manual must be respected:

BO105 C/CS TempRev 1 BO105 CB/CBS TempRev 1 BO105 CB-5/CBS-5 TempRev 1 BO105 DB/DBS TempRev 1 BO105 DBS-5 TempRev 1 AMM/Aircraft Maintenance Manual:

The TBO for the control grip with coiled cable will be incorporated with the next revision of the maintenance manual chapter 101-14.2.

The supplementary inspection according to operating time for the control grip with coiled cable will be incorporated with the next revision of the maintenance manual chapter 101-10.2.

4 APPENDIX Not applicable.

PAGE 8 of 11 Revision 1, 2015-02-02 This document is available on the internet: www.airbushelicopters.com/techpub

Page 9OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150 Overhead panel, upper part (firmly riveted to cabin) Connection for the rescue winch Overhead panel, lower part control grip receptacle 25VEA (screwed with upper part) Control grip Coiled cable Control grip

INACTIVE Placard L311M3500324- Degrease the place to be bonded and affix placard using transparent adhesive silicone.

Installation Overhead panel (typical) Figure 1 Revision 1, 2015-02-02 PAGE 9 of 11 This document is available on the internet: www.airbushelicopters.com/techpub

Page 10OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150 Before modification OVERHEAD PANEL CONTROL GRIP 25VE 5VEa EA V 133VVa CABLE CUTTER 133V 15MF MF3M20 MF4E22 MF6E20

WINCH UP 14MF E

OUT I WINCH ARM IN >C -B DOWN After modification OVERHEAD PANEL CONTROL GRIP 25VE 25VEa 25VEA 133VVa K CABLE CUTTER 133V 15MF MF3M20 MF4E22 MF6E20

WINCH UP 14MF OUT, 1 | WINCH ARM IN Wire connection is necessary to guarantee the test function.

Wiring diagram for deactivation of the cable cutter on the control grip Figure 2 PAGE 10 of 11 Revision 1, 2015-02-02 This document is available on the internet: www.airbushelicopters.com/techpub

Page 11OCROpen in PDF

AIRBUS HELICOPTERS ASB BO105-80A-150 ISTRUMENT PANEL 2VE OVERHEAD PANEL

MAIN BUS BAR PP21 WINCH 1MF 4MF

CABLE CUTTER 2MF RESCUE WINCH 24MF @a@a CABLE CUTTER 7MF

WINCH SMF WINCH 6VE-W COLL. LEVER CABLE 01 UP CUTTER 13MF

OUT IN WINCH 12MFO DOWN

DEACTIVATION OF

CABLE CUTTER ON

CONTROL GRIP

CONTROL BOARD 33MF CUTTER 15MF LIMIT SWITCH CONTROL GRIP 25 LIMIT SWITCH DOWN RELAY BOX 23VE 20MF

STARTER BUS BAR

EXPLOSIVE CARTRIDGE 3MF

WINCH ARM MOTOR 16 MF SERIES

RESISTOR 3 BRAKE 3 MOTOR 3 WINDING FIELD

THERMOSTAT WINCH UNIT 17MF Functional diagram Rescue winch Figure 3 Revision 1, 2015-02-02 PAGE 11 of 11 This document is available on the internet: www.airbushelicopters.com/techpub