Service bulletin · Airbus Helicopters

Revision 1U.S. DOT/FAA - ASB No EC120-52A014 Rev 1 · 19 pages · 318 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-1090; AD 2014-12-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2013-1090 (document 0004) · AD 2014-12-12

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
EC120-52A014
Latest revision known
EC120-52A014, Revision 2, dated October 28, 2013

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 2 proposed ADs.

Text · 19OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-1090; AD 2014-12-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '55981b241e1e03d8829344ae33b1c2648f92211d2cf506ae618c6fd13932f30e'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014 Civil version(s): B

ALERT SERVICE BULLETIN SUBJECT: DOORS - Sliding door Attachment of the sliding door star support For the attention of Revision No. Date of issue Revision 0 2004-01-16 Revision 1 2013-01-25 Summary:

Reinforce the sliding door star support attachment.

Reason for last Revision:

The purpose of Revision 1 of this ALERT SERVICE BULLETIN is to change Service Bulletin No. 52-014 into ALERT SERVICE BULLETIN No. 52A014, to make mandatory the improvement of the sliding door star support attachment.

Compliance:

EUROCOPTER makes compliance with this ALERT SERVICE BULLETIN mandatory.

Revision 0 2004-01-16 Page 1/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 2OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment Helicopters whose serial number (S/N) is strictly lower than 1368, equipped with sliding door P/N C526A2370101, on which Revision 0 of this ALERT SERVICE BULLETIN was not complied with.

1.A.2. Non-installed equipment Sliding doors (MP/N) C526A2370101 which did not comply with Revision 0 of the Service Bulletin N°52-0 14.

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON Revision 0:

Avoid paint chips on the sliding door outside skin on external rivets, by reinforcing the star support pin attachment.

Revision 1:

EUROCOPTER has been informed of an incident concerning the star support pin rupture. This part is located on the kinematics of the sliding door locking system.

The star support pin rupture make makes impossible all sliding door operations.

Investigations have revealed that the helicopter affected had not complied with Revision 0 of this Service Bulletin No 52-014.

The purpose of Revision 1 is to:

- change Service Bulletin No. 52-014 into ALERT SERVICE BULLETIN No. 52A014, to make mandatory embodiment of improvement of the sliding door star support attachment,

- add a star pin dye penetrant inspection procedure,

- add removal and installation procedures of a part of the locking system kinematics,

- to make this revision compliant with the new ALERT SERVICE BULLETIN layout.

EUROCOPTER therefore makes mandatory the star pin check using dye penetrant inspection, as well as compliance with the improvement (doubling the star support pin yoke).

Revision 1 of this ALERT SERVICE BULLETIN does not supersede compliance with Revision 0 of the Service Bulletin No 52-014.

1.D. DESCRIPTION The improvement consists in reinforcing the star support pin using a double yoke system, which enables the rod stress to be more efficiently sustained, which thus avoids this pin to brake.

Revision 0 2004-01-16 Page 2/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 3OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

1.E. COMPLIANCE

1.E.1. Compliance at the works Not applicable.

1.E.2. Compliance in service The works must be performed on helicopter by the operator.

Helicopters/Installed equipment:

Comply with Paragraph 3. of this ALERT SERVICE BULLETIN before reaching 165 flying hours without exceeding 2 years, following receipt of this ALERT SERVICE BULLETIN, issued on the date mentioned in page tooter.

Non-installed equipment:

Modify stock as per paragraphs 3.A. and 3.B.4. of this ALERT SERVICE BULLETIN, prior to installation on helicopter and without exceeding 2 years.

1.F. APPROVAL Approval of modifications:

The information or instructions relate to Aircraft Modification Approval Form (FAM) A00565 Issue 1 which was approved on April 03, 2003 under the authority of DGAC Design Organisation Approval No.FJA01.

Approval of this document:

The technical information contained in this Service Bulletin No. 52-014 Revision 0 was approved on January 16, 2004 under the authority of DGAC Design Organization Approval No. F.JA01.

The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on January 24, 2013 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.

Revision 0 2004-01-16 Page 3/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 4OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

1.G. MANPOWER For compliance with this ALERT SERVICE BULLETIN, EUROCOPTER recommends the following personnel qualifications:

Qualifications: - 2 Mechanical Technicians,

- 1 Composite Specialist.

Times are given for reference, for a standard configuration.

Time for the operations: - 5 hours (approximately) for the removal/installation of the sliding door, covering and linkage for 2 mechanical technicians,

- 5 hours (approximately) for the replacement of the star support and glass fabric plies for 1 composite specialist.

The estimated helicopter grounding time is one day and a half approximately, excluding curing time of glass fabric ply/plies under vacuum bag and drying of the different products.

1.H. WEIGHT AND BALANCE Weight: 0.06 kg.

Longitudinal moment: 0.132 m.kg Lateral moment: -0.042 m.kg Vertical moment: -0.139 m.kg

1.I. EFFECT ON ELECTRICAL LOADS Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD Not applicable.

Revision 0 2004-01-16 Page 4/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 5OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

1.K. REFERENCES The following documents are necessary for compliance with this ALERT SERVICE BULLETIN:

Aircraft Maintenance Manual (AMM):

20-10-00, 3-1 : Locking - Airframe 20-10-00, 3-8: Cleaning of Mechanical Parts - Airframe 20-10-00, 3-10: Method for Application of Primer Paints - Airframe 20-10-00, 3-14: Method for application of Sealants - Airframe 20-10-00, 3-15 : Bonding with Adhesives - Airframe 20-10-00, 3-19 : Dye Check - Airframe 20-10-00, 3-27: Method for Installing and Replacing the Rivets - Airframe 20-10-00, 3-32 : Bonding with adhesive (HYSOL EA 9396) 20-10-00, 3-33 : General riveting acceptance requirements - Airframe 20-10-00, 3-35 : Resin Application Procedure HYSOL EA 9395 - Airframe 20-10-00, 3-43 : Monitoring of Equipment in Service, Marking and Specific version Identification - Airframe 20-10-00, 3-45 : Method for Installation of Blind Rivets ASN-NSA 1919 et 1921 - Airframe 20-20-00, 3-1: Standard Practices - Structure 25-23-00, 4-1 : Removal / Installation - Upholstery 52-50-00, 4-1 : Removal - Cabin Sliding Doors Assy 52-50-00, 4-2: Installation - Cabin Sliding Doors Assy 52-50-00, 6-1: Inspection - Cabin Sliding Door

1.L. DOCUMENTS AFFECTED Not applicable.

1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS Not applicable.

Revision 0 2004-01-16 Page 5/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 6OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

2. MATERIAL INFORMATION

2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT For all information concerning the kits and/or components, contact the EUROCOPTER Network Sales and Customer Relations Department.

Order the required quantity from:

EUROCOPTER Etablissement de Marignane Direction Ventes et Relations Client (ECR) 13725 MARIGNANE CEDEX FRANCE NOTE 1 On the purchase order, please always specify the mode of transport, the destination and the serial numbers of the aircraft to be modified.

NOTE 2 For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4.42.85.99.96.

2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT Not applicable.

2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT Kits or components to be ordered for one helicopter or one assembly:

New Former Key Word Qty P/N Item P/N Instruction Kit including: C008A005650071 Cotter pin 1 EN2367-18020 10 EN2367-18020 Scrap Cotter pin 23310CA010015 11 23310CA010015 Scrap Plate 1 C526A2370201 15 Angle bracket 1 C526A2369201 16 Rivet 2 21215TB3205 18 Blind rivet 4 ASNA0077E406 19 Revision 0 2004-01-16 Page 6/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 7OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014 Material to be ordered separately:

New Former Key Word Qty Item P/N P/N Instruction Support AR 677-1-20-511 2 677-1-20-511 Rivet 1 NAS1919C04S03U NAS1919C04S03U Scrap Rivet ASNA0077E403 4 ASNA0077E403 Scrap Glass fabric AR ECS0030-27 6 ECS0030-27 Scrap Dry carbon fabric AR ECS0031-12 13 End fitting AR 677-1-10-514 14 677-1-10-514 Products to be ordered separately:

As per Tasks mentioned in this ALERT SERVICE BULLETIN and list below:

Key Word Qty Product P/N CM Item Adhesive AR ECS6054-1031 6041 1 Adhesive tape AR Scotch 3M 471 or equivalent 783 5 Adhesive compound AR ECS0010.10 7 Primer paint AR ECS2067.20 8 Grease AR DCSEA354 115 9 Grease AR DCSEA395 101 12 Sealant AR ECS2068.10 6240 17 The products can be ordered separately, from INTERTURBINE AVIATION LOGISTICS company.

Website: http://www.interturbine.com Phone: +49.41.91.809.300 AOG: +49.41.91.809.444

2.D. A MATERIAL TO BE RETURNED Not applicable.

Revision 0 2004-01-16 Page 7/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 8OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL Read and comply with instructions for safetying as per AMM Task 20-10-00, 3-1.

Read and comply with instructions for cleaning as per AMM Task 20-10-00, 3-8.

Read and comply with instructions for bonding with adhesives as per AMM Task 20-10-00, 3-15.

Read and comply the method for installing and replacing the rivets as per AMM Task 20-10-00, 3-27.

Read and comply standard practices as per AMM Task 20-20-00, 3-1.

3.B. OPERATIONAL PROCEDURE

3.B.1. Preliminary steps (Figure 1)

- Park the helicopter in a hangar.

- Clear access to work zones.

- Install suitable access means.

- Remove sliding door (a) (Figure 1) as per AMM Task 52-50-00, 4-1 and install it on a workbench.

- Remove the sliding door skin as per AMM Task 25-23-00, 4-1.

- Protect the covering of sliding door (a) and install it on a workbench.

3.B.2. Reinforcing the sliding door star support attachment (Figures 1 to 6)

3.B.2.a. Disconnecting rods and removing the star (Figure 1)

- Remove and discard cotter pins (e) (Detail A, Figure 1).

- Remove pins (d).

- Disconnect rods (b), (c) and (i) from star (h), and lock them in order to disengage the work zone.

- Remove and scrap cotter pin (f) and washer (g).

- Remove star (h).

3.B.2.b. Visual inspection of upper and lower locking pin control rod end fittings (Figure 1)

- Examine both end fittings (s) (Detail A, Figure 1) and make sure that they are neither twisted nor broken:

. if both end fittings (s) are neither twisted nor broken:

- leave as Is,

- comply with Paragraph 3.B.2.c.

. if at least one of the two end fittings is twisted or broken:

- using a rule, measure and record length (L),

- loosen locknut (r),

- loosen and remove end fitting (s) concerned,

- remove locknut (r),

- scrap end fitting (s),

- clean locknut (r) threading with Methyl-ethyl-ketone (13) in order to remove any trace of thread lock,

- screw locknut (r) on end fitting (14) threading to length (L),

- screw end fitting (14) until locknut (r) touches the related rod, Revision 0 2004-01-16 Page 8/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 9OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014 NOTE 1 End fitting (14) can be screwed in or out a quarter turn maximum to enable free pin (d) fitting into star (h).

- lock the related rod in order to disengage the work zone.

3.B.2.c. Checking the star support pin using dye penetrant inspection (Figures 1 to 4)

- Clean zones X and Y (Detail C, Figure 3).

- Check for cracks on pin (k) of support (k), on zones X and Y using a dye penetrant inspection as per AMM Task 20-10-00, 3-19:

. If no cracks are found:

- put star (h) in position (Detail A, Figure1),

- embody the improvement of the sliding door star support attachment as per Paragraph

3.B.2.d.

. If there is a crack:

- remove and scrap glass fabric plies (p) (intervention zone E, Figure 4),

- clean contact surfaces between glass fabric plies (p) and sliding door (a) skin,

- remove and scrap rivet (m) (Detail B, Figure 2) and the three rivets (n),

- remove and scrap support (k),

- clean contact surfaces between sliding door (a) skin and support (k),

- interlay adhesive (1) (not shown in the Figure) between sliding door (a) skin and support (2) as per AMM Task 20-10-00, 3-35,

- put support (2) in position using a rivet (3) and three rivets (4) as per AMM Task 20-10-00, 3-33 and 20-10-00, 3-45,

- delimit work zone Z (intervention zone E, Figure 4) using adhesive tape (5) (not shown in the Figure),

CAUTION

WHILE GRINDING, DO NOT DAMAGE THE FIRST PLIES OF SLIDING DOOR (a) SKIN IN CARBON FABRIC (DETAIL D, FIGURE 4).

- using abrasive paper (grit size 80 to 240), remove the finish paint and primer paint on work zone Z, up to the carbon fiber,

- cut out three square-shaped glass fabric plies (6) as per intervention zone E (Figure 4), NOTE 2 If the surtace of a glass fabric ply (6) enables it, it is possible to cover several rivet heads with only one glass fabric ply (6).

Revision 0 2004-01-16 Page 9/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 10OCROpen in PDF

• EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014 NOTE 3 When installing to the center a glass fabric ply (6) on several rivet heads (4), it is necessary to leave a distance of at least 20 mm (.79 in.) between rivet head (4) and the square outer edge.

- apply adhesive compound (7) on the glass fabric ply/-ies (6) as per AMM Task 20-10-00, 3-32,

- center a glass fabric ply (6) on apparent rivet heads (4),

- cure the glass fabric ply/-ies (6) in a vacuum bag,

- carry out a surface treatment before painting,

- apply a primer paint layer (8) on work zone Z as per AMM Task 20-10-00, 3-10,

- apply a finish paint layer as per the color of sliding door (a) outer skin (Detail D, Figure 4),

- apply grease (9) (Detail C, Figure 3) on Zone X,

- put star (h) in position (Detail A, Figure 1),

- carry out the improvement of the star attachment as per paragraph 3.B.2.d.

3.B.2.d. Embodiment of modification A00565 - Reinforcing the sliding door star support (Figures 5 and 6)

- Reinforce stringer (q) (Section H-H, Figure 6) by means of three carbon fabric plies (13) soaked with adhesive (7).

NOTE 4 The orientation of carbon fabric plies (13) has no importance whatsoever.

- Put in position plate (15) on support (k) or (2) pin and center it.

- Put in position angle bracket (16) under stringer (q) and put it against plate (15).

- Secure angle bracket (16) and plate (15) assembly

- Counter-drill two holes dia 3.3 mm (.13 in.) in angle bracket (16), to match plate (15) holes.

- Pin angle bracket (16) and plate (15).

- Counter-drill four holes dia 3.3 mm (.13 in.) in stringer (q), to match angle bracket (16) holes.

- Interlay sealant (17) between angle bracket (16) and plate (15), as per AMM Task 20-10-00, 3-14.

- Put in position angle bracket (16) on plate (15) by means of two rivets (18) (Detail G, Figure 6).

- By means of four rivets (19) (Section J-J, Figure 6), put in position plate (15) (Section H-H, Figure 6) and angle bracket (16) assembly on stringer (q).

- Put in position cotter pin (10) (Detail A, Figure 1) without locking it.

- Connect rods (b), (c) and (j) to star (h), and secure them by means of pins (d).

- Lock each pin (d) by means of a cotter pin (11).

- Apply grease (12) (Detail B, Figure 2) to zones T, U, V and W.

- Lock star (h) (Detail F, Figure 5) by means of cotter pin (10) (Detail G, Figure 6).

- Mark as per Paragraph 3.C. of this ALERT SERVICE BULLETIN.

Revision 0 2004-01-16 Page 10/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 11OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

3.B.3. Final steps (Figure 1)

- Put in position sliding door (a) skin as per AMM Task 25-23-00, 4-1.

- Put in position sliding door (a) as per AMM Task 52-50-00, 4-2.

- Perform operating test of the sliding door as per AMM Task 52-50-00, 6-1.

- Perform aircraft appearance checks.

- Remove the access means.

3.B.4. Operational procedure on non-installed equipment

- Retrofit stock of sliding doors as per Paragraph 3.B.2. of this ALERT SERVICE BULLETIN.

3.C. IDENTIFICATION Identification of this document:

Record compliance with this ALERT SERVICE BULLETIN Revision 1 on the helicopter documents.

Identification of modifications on the equipment:

Identify the assembly as per the table below and AMM Task 20-10-00, 3-43.

Key Word Former P/N New P/N MOD Marking type Sliding door assembly C526A2370101 + ASB No. 52A014 R1 C526A2370101 ASB No. 52A014 R1 Indelible ink

3.D. OPERATING AND MAINTENANCE INSTRUCTIONS Not applicable.

Revision 0 2004-01-16 Page 11/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub

Page 12OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC120-52A014

PAGE LEFT BLANK INTENTIONALLY Revision 0 2004-01-16 Page 12/19 Revision 1 2013-01-25 This document is available on the Internet: www.eurocopter.com/techpub