Service bulletin · Airbus Helicopters

Revision 1Airbus Helicopters ASB MBB-BK117 D-2-00A-001 Rev 1 · 11 pages · 815 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0126; AD 2021-10-23 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2021-0126 (document 0004) · AD 2021-10-23

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
MBB-BK117 D-2-00A-001
Latest revision known
MBB-BK117 D-2-00A-001, Revision 1, dated October 16, 2019

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 11OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0126; AD 2021-10-23 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '7de59981b526b04aeefcb0a504d2ed10e5053a820e63fcea92acc702a9d0a2a0'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001 Valid for Version(s): D-2, D-2m.

ALERT SERVICE BULLETIN

PROTECTIVE MEASURE AIR VEHICLE GENERAL - General information Inspection of Titanium Bolts For the attention of Revision No. Date of issue Revision 0 2019-08-12 Revision 1 2019-10-16 Summary:

With this Alert Service Bulletin (ASB), Airbus Helicopters Deutschland (AHD) prescribes a one-time inspection of Titanium Bolts (Ti-Bolts).

Reason for last Revision:

Please replace Revision 0 of this ASB with Revision 1.

Revision 1, adds the alternative Ti-Bolt EN3740-060022F in Section 2.C. In addition, the procedure has been improved.

If the Revision O of this ASB has already been accomplished no further work is required due to this Revision, provided that the replacement bolts (if required) were ordered at AHD Spares Order Administration.

Compliance:

Compliance with PART I of this ASB is mandatory (part of EASA AD).

Compliance with PART Il of this ASB is essential (not part of EASA AD).

Revision 1, 2019-10-16 PAGE 1 of 11 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001 1 PLANNING INFORMATION

1.A EFFECTIVITY

1.A.1 Helicopters/installed equipment and parts

a) MBB-BK117 D-2, D-2m, all S/N up to 20310 inclusive.

b) Ti-Bolts with manufacturer monogram "D": EN3740-060022F EN3308-050030F

1.A.2 Non-installed equipment and parts See Section 1.A.1.b.

1.B ASSOCIATED REQUIREMENTS None.

1.C REASON Some Ti-Bolts have been manufactured according to an improper heat treatment process. This improper process can lead to hydrogen embrittlement of the parts far above standard limits. Affected Ti-Bolts must be identified by an inspection and Ti-Bolts with the manufacturer monogram "D" must be replaced. For additional information, see SIN 3365-S-00.

1.D DESCRIPTION Inspect the Ti-Bolts. Replace the Ti-Bolts, if required.

COMPLIANCE

1.E.1 Compliance at H/C manufacturer level Helicopters/ installed equipment and parts:

The inspection and replacement (if required) of the Ti-Bolts must be accomplished in accordance with Section 3.B of this ASB before delivery of the helicopter.

Non-installed equipment and parts:

Ti-Bolts with manufacturer monogram "D" must neither be installed nor delivered.

1.E.2 Compliance in service Helicopters/installed equipment and parts:

PART I The inspection and replacement (if required) of the Ti-Bolts must be accomplished in accordance with Section 3.B.2 of this ASB within the next 50 Fh or 3 months whichever occurs first after receipt of Revision 0 of this ASB.

PAGE 2 of 11 Revision 1, 2019-10-16 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001

PART II The inspection and replacement (if required) of the Ti-Bolts must be accomplished in accordance with Section 3.B.3 of this ASB before 31 May, 2021 at the latest.

Non-installed equipment and parts:

Ti-Bolts with manufacturer monogram "D" must not be installed.

1.F APPROVAL Approval of this document:

The technical content of this document is approved under the authority of DOA No. EASA.21J.700.

1.G MANPOWER Qualification Mechanic Electrician Pilot Others approx. 3 h (inspection) Estimated Man-hours approx. 2 h (replacement, if required)

1.H WEIGHT AND BALANCE No effect on weight and balance.

1.I POWER CONSUMPTION Not affected.

1.J SOFTWARE UPGRADES/UPDATES Not changed.

1.K REFERENCES AMM MBB-BK117 D-2, Standard Practices Manual (MTC).

1.L OTHER AFFECTED PUBLICATIONS Not affected.

1.M INTERCHANGEABILITY OR MIXABILITY OF PARTS Interchangeability:

After accomplishment of this ASB, the Ti-Bolts with the manufacturer monogram "D" must not be installed anymore.

Mixability:

Not affected.

Revision 1, 2019-10-16 PAGE 3 of 11 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001

MATERIAL INFORMATION Z.A MATERIAL: PRICE - AVAILABILITY - PROCUREMENT None.

2.B LOGISTIC INFORMATION None.

2.C MATERIAL REQUIRED PER HELICOPTER/COMPONENT Material supplied by the operator:

The following parts could be affected by a replacement. Affected parts shall be ordered at AHD Spares Order Administration.

Please reference the following number in the customer order:

ASB-MBB-BK117-D-2-00A-001 PARTI No. Keyword Qty New P/N Old P/N Rem.

EN2549D060022F A, B or ECS0403-060022F A, B or Ti-Bolt 2 DIN65338K06022T A, B or EN3740-060022F EN3740-060022F C, D

PART II No. Keyword Qty New P/N Old P/N Rem.

EN3308-050030F 1 Ti-Bolt 8 EN3308-050030F C, D Remark:

A = Without manufacturer monogram "D".

B = Preferred alternative.

C = With manufacturer monogram "D".

D = AHD does not take back parts with old part numbers.

PAGE 4 of 11 Revision 1, 2019-10-16 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001 Consumables to be ordered separately:

WARNING

RESPECT THE SAFETY DATA SHEET OF THE MANUFACTURER.

No. Keyword Qty. Specification ** Rem.

(approx.)

1 Sealing compound a.n.* 6050 A, B *a.n. = as needed ** For specification, refer to AMM 01-00-00, 2-1.

Remark:

A = If required.

B = Sealing compound CM 6068 can be used as an alternative material.

The consumables can be ordered separately from the BDSI company.

Website: https://www.boeingdistribution.com Telephone: +1.305.925.2600 Fax: +1.305.507.7191 AOG: +1.305.471.8888 AOG email: AOGdesk@boeingdistribution.com

2.D MATERIAL TO BE RETURNED None.

Revision 1, 2019-10-16 PAGE 5 of 11 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001

ACCOMPLISHMENT INSTRUCTIONS З.А GENERAL Not applicable.

З.В WORK STEPS З.В.1 Preliminary steps

1. De-energize the helicopter electrical system (AMM 24-32-00, 2-1).

PARTI

2. Remove tail structure access cover (AMM 52-40-00, 4-9).

3. Remove gearbox fairing (AMM 53-51-01, 4-5).

WARNING

DO NOT INSTALL TI-BOLTS WITH MANUFACTURER MONOGRAM "D".

NOTE Ti-Bolts with manufacturer monogram "D" should be replaced one by one.

NOTE The manufacturer monogram may not appear exactly as shown in the figures. If confirmation is needed contact your AH customer support.

PARTI

3.B.2 Inspection of the AFT connection of ball bearing control Inspect the manufacturer monogram (1, Fig. 1) marked on the head of the Ti-Bolt (5):

a. If the manufacturer monogram (1, Fig. 1) can be identified and is clearly not "D", proceed in accordance with Section 3.B.2.3.

b. If the manufacturer monogram (1, Fig. 1) is "D", replace the Ti-Bolt (5) in accordance with Section 3.B.2.2.

c. If the manufacturer monogram (1, Fig. 1) cannot be identified, replace the Ti-Bolt (5) in accordance with Section 3.B.2.2.

2. Replacement of the Ti-Bolt (5, Fig. 1):

a. Remove the Ti-Bolt (5, Fig. 1) (AMM 67-20-00, 4-17).

b. Install a Ti-Bolt (5, Fig. 1) with an identifiable manufacturer monogram that is clearly not "D" (AMM 67-20-00, 4-18). See Section 2.C for the required material.

PAGE 6 of 11 Revision 1, 2019-10-16 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001

3. Inspect the manufacturer monogram (1, Fig. 1) marked on the head of the Ti-Bolt (2):

a. If the manufacturer monogram (1, Fig. 1) can be identified and is clearly not "D", proceed in accordance with Section 3.B.3 to accomplish PART II or 3.B.4 to accomplish the final steps of PART I.

b. If the manufacturer monogram (1, Fig. 1) is "D", replace the Ti-Bolt (2) in accordance with Section 3.B.2.4.

c. If the manufacturer monogram (1, Fig. 1) cannot be identified, replace the Ti-Bolt (2) in accordance with Section 3.B.2.4.

4. Replacement of the Ti-Bolt (2, Fig. 1):

a. Remove the Ti-Bolt (2, Fig. 1) (AMM 67-20-00, 4-19).

b. Install a Ti-Bolt (2, Fig. 1) with an identifiable manufacturer monogram that is clearly not "D" (AMM 67-20-00, 4-20). See Section 2.C for the required material.

c. Proceed in accordance with Section 3.B.3 to accomplish PART II or 3.B.4 to accomplish the final steps of PART I.

Revision 1, 2019-10-16 PAGE 7 of 11 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001 View A View B 2 9 8 C View C 4N 3780 1 Manufacturer monogram 2 Ti-Bolt EN3740-060022F 3 Fenestron actuator 4 Input lever 5 Ti-Bolt EN3740-060022F 6 Mobile end rods 7 Flexball Tail Rotor (T/R) 8 Bellows 9 Rod Assembly The manufacturer monogram may not appear exactly as shown.

If confirmation is needed contact your AH customer support.

Inspection of the AFT connection of ball bearing control Figure 1 PAGE 8 of 11 Revision 1, 2019-10-16 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001

PART II З.В.З Inspection of the HF antenna brackets EFFECTIVITY All helicopter with HF antenna brackets.

1. Inspect the manufacturer monogram (5, Fig. 2) marked on the head of the Ti-Bolt (3):

a. If the manufacturer monogram (5, Fig. 2) can be identified and is clearly not "D", proceed in accordance with Section 3.B.3.3.

b. If the manufacturer monogram (5, Fig. 2) is "D", replace the Ti-Bolt (3) in accordance with Section 3.B.3.2.

c. If the manufacturer monogram (5, Fig. 2) cannot be identified, replace the Ti-Bolt (3) in accordance with Section 3.B.3.2.

2. Replacement of the Ti-Bolt (3, Fig. 2):

a. Remove the Ti-Bolt (3, Fig. 2) and washer (4).

b. Discard the Ti-Bolt (3, Fig. 2).

c. Install a Ti-Bolt (3, Fig. 2) with an identifiable manufacturer monogram that is clearly not "D" and washer (4).

d. Torque the Ti-Bolt (3, Fig. 2) (MTC 20-02-05-404).

3. Inspect the manufacturer monogram (5, Fig. 2) marked on the head of the Ti-Bolt (7):

a. If the manufacturer monogram (5, Fig. 2) can be identified and is clearly not "D", proceed in accordance with Section 3.C.

b. If the manufacturer monogram (5, Fig. 2) is "D', replace the Ti-Bolt (7) in accordance with Section 3.B.3.4.

c. If the manufacturer monogram (5, Fig. 2) cannot be identified, replace the Ti-Bolt (7) in accordance with Section 3.B.3.4.

4. Replacement of the Ti-Bolt (7, Fig. 2):

a. Remove the Ti-Bolt (7, Fig. 2) and washer (6).

b. Discard the Ti-Bolt (7, Fig. 2).

c. Install a Ti-Bolt (7, Fig. 2) with an identifiable manufacturer monogram that is clearly not "D" and washer (6).

d. Torque the Ti-Bolt (7, Fig. 2) (MTC 20-02-05-404).

Revision 1, 2019-10-16 PAGE 9 of 11 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001 View A FW D Detail C Detail B

FW D FW D — 8 OD 2 , 7×4/2 3 x4 /2 _ 6x4 /2 4x4 x4/2 1 HF antenna «N 3300 2 Console 2 assy D231M1018101 3 Ti-Bolt EN3308-050030F 4 Washer D 5 Manufacturer monogram 6 Washer 7 Ti-Bolt EN3308-050030F 8 Console 3 assy D231M1019101 The manufacturer monogram may not appear exactly as shown.

If confirmation is needed contact your AH customer support.

Apply sealing compound (CM 6050).

Inspection of the HF antenna brackets Figure 2 PAGE 10 of 11 Revision 1, 2019-10-16 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-00A-001

3.В.4 Final steps

WARNING

MOVING PARTS MUST NOT TOUCH AND MUST

HAVE SUFFICIENT CLEARANCE BETWEEN THEM.

1. Move all controls several times through the full range and check the rotor flight controls for free movement over the whole stroke.

2. Install gearbox fairing (AMM 53-51-01, 4-5).

3. Install tail structure access cover (AMM 52-40-00, 4-9).

З.С COMPLIANCE CONFIRMATION Compliance with this document:

PARTI Confirm accomplishment of PART I of this ASB by an entry in the historical record of the helicopter.

PART II Confirm accomplishment of PART Il of this ASB by an entry in the historical record of the helicopter.

3.D OPERATING AND MAINTENANCE INSTRUCTIONS None.

APPENDIX None.

Revision 1, 2019-10-16 PAGE 11 of 11 This document is available on the internet: www.airbushelicopters.com/techpub/