Service bulletin · Airbus Helicopters

No revision namedAirbus Helicopters ASB No. SA330-53.56 Rev 0 · 12 pages · 745 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2024-1686, the docket of AD 2024-18-05. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2024-1686 (document 0005) · AD 2024-18-05

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
SA330-53.56

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 12OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2024-1686, the docket of AD 2024-18-05. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '9837cdc67baf34070dcae1d5a59e0158a0d30382fc81e2ed7c568c018583f7f6'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56 Civil version(s): J Military version(s): Ba, L, Sm

ALERT SERVICE BULLETIN

PROTECTIVE MEASURE FUSELAGE - Primary structure Check of suspension bars attachment plates For the attention of Revision No. Date of issue Revision 0 2023-04-03 Summary:

The purpose of this ALERT SERVICE BULLETIN is to make sure that:

- The front suspension bar attachment plate is compliant with the design of helicopters version Ba

- The RH and LH rear suspension bars attachment plates are compliant with the design of helicopters versions Ba, J, L and Sm.

Compliance:

It is mandatory to comply with this ALERT SERVICE BULLETIN.

Revision 0 2023-04-03 Page 1/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment or parts Helicopters SA330 versions Ba, J, L and Sm.

1.A.2. Non-installed equipment or parts Not applicable.

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON Reminder: so-called MK1 versions correspond to Super Puma helicopters AS332 C, C1, L, L1, B, B1, F1, M, M1, AS532 AC, AL, SC, UE, UL, so-called MK2 versions correspond to Super Puma helicopters AS332 L2, AS532 A2, AS532 U2 and so-called MK2+ versions correspond to Super Puma helicopters EC225 LP and EC725 AP.

During a maintenance of a helicopter from the Super Puma family, the diameter of the hole of the RH rear suspension bar attachment plate was checked at 33 mm (1.3 in) instead of 30 mm (1.181 in).

The RH rear Main Gear Box (MGB) fitting and the RH rear suspension bar attachment plate were also found damaged with a lot of fretting marks and oversized holes.

This was the result of erroneous installation of an AS332 MK2 or MK2+ plate instead of an AS332 MK1 plate and, therefore, the ALERT SERVICE BULLETIN No. 53.02.15 has been issued.

As the design of the Puma SA330 suspension bar attachment plates is partially similar to the design of the Super puma MK1 plates, it was decided to adapt the protective measures from the Super puma MK1 to the Puma SA330.

Consequently, the purpose of this ALERT SERVICE BULLETIN is to make sure that:

- The front suspension bar attachment plate is compliant with the design of helicopters version Ba.

- The RH and LH rear suspension bars attachment plates are compliant with the design of helicopters versions Ba, J, L and Sm.

1.D. DESCRIPTION The ALERT SERVICE BULLETIN includes the work steps that follow:

- Do a visual check of:

. The RH rear suspension bar attachment plate for helicopters versions Ba, J, L and Sm . The LH rear suspension bar attachment plate for helicopters versions Ba, J, L and Sm

- Do a measurement of the front suspension bar attachment plate only for helicopters version Ba

- Make sure that the RH and LH rear suspension bars attachment plates are for helicopters versions Ba, J, L and Sm.

- Make sure that the front suspension bar attachment plate is for helicopters SA330 version Ba

- Return the response form to Airbus Helicopters.

Revision 0 2023-04-03 Page 2/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

1.E. COMPLIANCE

1.E.1. Compliance at H/C manufacturer level Not applicable.

1.E.2. Compliance in service Helicopters/installed equipment or parts:

The operator must do the work on the helicopter.

Comply with paragraph 3. not more than 50 flight hours after you received this ALERT SERVICE BULLETIN.

Refer to the issue date on the page footer.

Non-installed equipment or parts:

Not applicable.

1.F. APPROVAL The technical content of this document is approved under the authority of the Design Organization Approval ref. EASA. 21J.700.

The technical content of this document is approved under the prerogatives of the recognition of design capability ref. FRA21J-002-DGA for French Government helicopters.

The technical content of this document is approved by Airbus Helicopters Airworthiness Department for export military versions.

1.G. MANPOWER Airbus Helicopters recommends that the personnel who will do this Service Bulletin have this qualification:

Qualification: 1 Mechanical Technician.

The man-hours are an estimate given for information only and for a standard helicopter configuration.

Estimated Man-hours: 2 hours for the Mechanical Technician.

The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.

The estimate of the helicopter downtime is 2 hours.

1.H. WEIGHT AND BALANCE Not applicable.

1.I. POWER CONSUMPTION Not applicable.

Revision 0 2023-04-03 Page 3/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

1.J. SOFTWARE UPGRADES/UPDATES Not applicable.

1.K. REFERENCES The following documents are required for compliance with this ALERT SERVICE BULLETIN.

Standard Practices Manual (MTC):

MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power generating systems - Technical instructions MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions Information Notices (IN):

IN: 3041-1-00: In need of your Technical Support? Contact us 24/7/365!

IN: 3481-1-00: The Marketplace: an AirbusWorld Ordering service IN: 3785-1-00: Introduction of the digital Service Bulletin reporting service SB Insight

1.L. OTHER AFFECTED PUBLICATIONS Not applicable.

1.M. PART INTERCHANGEABILITY OR MIXABILITY Not applicable.

Revision 0 2023-04-03 Page 4/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

2. EQUIPMENT OR PARTS INFORMATION

2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT Price For any information on the price of modification kits and/or components or for assistance, contact the Airbus Helicopters Network Sales and Customer Relations Department.

Availability Delivery lead times will be indicated by the Sales and Customer Relations Department on the operator's request.

Procurement Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:

Airbus Helicopters Etablissement de Marignane Direction des Ventes et Relations Client 13725 MARIGNANE CEDEX FRANCE In the purchase order, write the information that follows:

- The mode of transport

- The destination

- The serial numbers of the helicopters to change.

2.B. LOGISTIC INFORMATION Not applicable.

2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT Consumables to be ordered separately:

Refer to Work Cards indicated in this ALERT SERVICE BULLETIN.

You can order the consumables from the AirbusWorld Marketplace through e-ordering (IN No. 3481-1-00).

If you cannot get access to e-ordering, please contact your Logistic Focal Point.

Special tools:

Refer to Work Cards given in this ALERT SERVICE BULLETIN and the list that follows:

Key Word Qty Tool P/N or equivalent Item Gauge Commercial P/N ZZ

2.D. EQUIPMENT OR PARTS TO BE RETURNED Not applicable.

Revision 0 2023-04-03 Page 5/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL Non applicable.

3.B. WORK STEPS

3.B.1. Preliminary steps

- Disconnect all the electrical power supplies refer to the Work Card 20-07-03-406 (MTC).

- Install the access equipment.

- Open the sliding cowling and the engine cowlings.

3.B.2. Procedure

3.B.2.a. Visual check of the RH and LH rear suspension bar attachment plates for helicopters versions Ba, J, L and Sm

- Do a visual check of the RH rear suspension bar attachment plate (a).

- Make sure that the RH rear suspension bar attachment plate (a) (Figure 1) is a SA330 versions Ba or J or L or Sm plate.

NOTE 1 Examine precisely the specific area (A) of the RH rear suspension bar attachment plate (a).

- Do a visual check of the LH rear suspension bar attachment plate (b).

- Make sure that the LH rear suspension bar attachment plate (b) (Figure 2) is a SA330 versions Ba or J or L or Sm plate.

NOTE 2 Examine precisely the specific area (A) of the LH rear suspension bar attachment plate (b).

- Comply with paragraph 3.B.2.b. only for helicopters version Ba.

- Comply with paragraph 3.B.2.c. for helicopters versions J, L and Sm.

Revision 0 2023-04-03 Page 6/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

3.B.2.b. Measurement of the front suspension bar attachment plate only for helicopters version Ba

- Position the gauge (zz) on the area (A) of the front suspension bar attachment plate (e) (Figure 3, Detail F and Figure 4 and Figure 5).

Area A e

- e

- m Figure 4 Figure 5

CAUTION DO NOT POSITION THE GAUGE (zz) (NOT SHOWN) ON THE MASTIC SEALING BEAD (m) OF THE FRONT SUSPENSION BAR ATTACHMENT PLATE (e) (FIGURE 5).

- Measure the front suspension bar attachment plate (e) with the gauge (zz) (Figure 3, Detail D).

- Comply with paragraph 3.B.2.c.

3.B.2.c. Interpretation of the results

- If the thickness of the front suspension bar attachment plate (e) is less or equal to 6.5 mm (.256 in) (only for helicopters version Ba).

And,

- The RH rear suspension bar attachment plates (a) is a SA330 versions Ba or J or L or Sm plate, And,

- The LH rear suspension bar attachment plates (b) is a SA330 versions Ba or J or L or Sm plate:

. Comply with paragraph 3.B.3.

- If the thickness of the front suspension bar attachment plate (e) is more than 6.5 mm (.256 in) (only for helicopters version Ba) and/or the RH rear suspension bar attachment plates (a) is a MK2 or MK2+ plate and/or the LH rear suspension bar attachment plates (b) is a MK2 or MK2+ plate:

. Contact Airbus Helicopters at the address that follows to get an approved repair:

. Airbus World: Technical Request Management https://airbusworld.helicopters.airbus.com . E-mail: support.technical-airframe.ah@airbus.com

- In any cases, complete and return the response form in the Appendix 4.A.

Revision 0 2023-04-03 Page 7/12 This document is available on the Internet: www.air elicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

3.B.3. Final steps

- Do an aspect check on the helicopter after inspection or repair, refer to the Work Card 20-07-03-408 (MTC).

- Close the sliding cowling and the engine cowlings.

- Connect all the electrical power supplies, refer to the Work Card 20-07-03-406 (MTC).

- Remove the access equipment.

3.C. RECORD OF COMPLIANCE Compliance with this document:

- Record the full compliance with this ALERT SERVICE BULLETIN, with the revision number, in the helicopter documents.

- Record compliance with this ALERT SERVICE BULLETIN (see IN 3785-1-00 for instructions):

QR code or hypertext link NOTE 3 The recording of compliance with ALERT SERVICE BULLETINS in the SB Insight tool does not replace the recording in the helicopter documents.

ASB SA330-53.56

3.D. OPERATING AND MAINTENANCE INSTRUCTIONS Not applicable.

Revision 0 2023-04-03 Page 8/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56 If SA330 versions Ba or Jor L or Sm RH rear plate installed:

Correct If MK2 or MK2+ RH rear plate installed:

Incorrect Back to paragraph 3.B.2.a.

Figure 1 - RH rear suspension bar attachment plate for versions Ba or J or L or Sm Revision 0 2023-04-03 Page 9/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56 If SA330 versions Ba or J or L or Sm LH rear plate installed:

Correct If MK2 or MK2+ LH rear plate installed:

Incorrect Back to paragraph 3.B.2.a.

Figure 2 - LH rear suspension bar attachment plate for versions Ba or J or L or Sm Revision 0 2023-04-03 Page 10/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56 D Area A

6.5 mm Max (.256 in) C

6.5 mm Max (.256 in) Back to paragraph 3.B.2.b.

Figure 3 - Front suspension bar attachment plate only for version Ba Revision 0 2023-04-03 Page 11/12 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 12OCROpen in PDF

AIRBUS HELICOPTERS No. SA330-53.56

4. APPENDIX

4.A. ALERT SERVICE BULLETIN RESPONSE FORM Response Form for ALERT SERVICE BULLETIN No. 53.56 "Check of suspension bars attachment plates" Return response form on SB Insight tool when you comply with paragraph 3.C. of this ALERT SERVICE BULLETIN.

In case you would not have access to the Technical Request Management, please send your response form to the following email address: customersupport.helicopters@airbus.com Please write in e-mail title the ALERT SERVICE BULLETIN reference - ALERT SERVICE BULLETIN title - Retex.

More details about Airbus Helicopters Technical Support organization and way to raise Technical Event available in IN 3041-1-00.

AIRBUS SB ID Card Questionnaire Page 1 of 1 Airbus Helicopters Questionnaire for SA330-53.56 SB ID Card Title FUSELAGE - Primary structure Check of suspension bars attachment plates Description The purpose of this ALERT SERVICE BULLETIN is to make sure that:

- The front suspension bar attachment plate is compliant with the design of helicopters version Ba

- The RH and LH rear suspension bars attachment plates are compliant with the design of helicopters versions Ba, J, L and Sm.

Compliance information Applied on:

On aircraft AC S/N: TTSN:

Questionnaire Is the RH rear suspension bar attachment plate an MK2 or MK2+ plate (for versions Ba or J or L or Sm)? *

• Yes • No Is the LH rear suspension bar attachment plate an MK2 or MK2+ plate (for versions Ba or J or L or Sm)? *

• Yes • No Is the front suspension bar attachment plate an SA330 version Ba plate (only for version Ba)? *

• Yes • No Revision 0 2023-04-03 Page 12/12 This document is available on the Internet: www. airb ushelicopters.com/techpub/